UCP 210
Pillow block ball bearing unit with extended inner
ring and set screw locking, cast iron, Japanese
standards
Pillow (plummer) block ball bearing units consist of an insert bearing
mounted in a cast iron housing that can be bolted to a support surface.
This variant is strong and stiff, and is suitable for applications with both
constant and alternating directions of rotation. It has an inner ring
extended on both sides and is locked onto the shaft by tightening a set
screw on the inner ring, making it easy to mount.
• Strong
• Designed for a constant and alternating rotation
• Ready to mount
• Lubricated and sealed bearing
• Quick locking onto the shaft
• Cost-effective
Overview
Dimensions
Shaft diameter 1.969 in
Centre height (pillow block) 2.252 in
Housing overall width 2.205 in
Centre distance between bolt holes 6.26 in
Bearing width, total 2.031 in
Performance Properties
Basic dynamic load 7 891 lbf Housing Pillow block
rating type
Basic static load 5 216 lbf Number of bolt holes 2
rating for fasteners
Limiting speed 3 300 r/min Fastening bolt Plain
hole type
Note Limiting speed with shaft
tolerance h6 Retaining feature, Set screws
inner ring
Bore Cylindrical
type
Rubber Without
seating ring
Generated from www.skf.com on 2024-01-27 Page 1 of 5
Material, Cast iron
housing
Material, Bearing steel
bearing
Without
Coating
Sealing, Seal and flinger on both sides
bearing
Sealing Contact, standard
type
Sealing, Without
unit
Grease
Lubricant
Relubrication With
hole
Grease With
fitting
Generated from www.skf.com on 2024-01-27 Page 2 of 5
Technical Specification
Compliance with standard JIS
Purpose specific For material handling applications
Material, housing Cast iron
Sealing, bearing Seal and flinger on both sides
Sealing type, bearing Contact, standard
Sealing, unit Without
Coating Without
Dimensions
d 1.969 in Bore diameter
d1 ≈ 2.445 Shoulder diameter of inner ring
in
A 2.205 in Base width
A1 1.26 in Top width
B 2.031 in Width of inner ring
B4 0.374 in Distance from locking device side face to
thread centre
H 2.252 in Height of spherical seat centre
H1 0.748 in Foot height
H2 4.567 in Overall height
J 6.26 in Distance between attachment bolts
J max. Distance between attachment bolts
6.339 in
J min. Distance between attachment bolts
6.181 in
L 8.13 in Overall length
N 0.787 in Diameter of attachment bolt hole
N1 0.866 in Length of attachment bolt hole
s1 1.283 in Distance from locking device side face to
raceway centre
Generated from www.skf.com on 2024-01-27 Page 3 of 5
Threaded hole
RG 1/8-27 NPT Housing thread for the grease fitting
R1 0.118 in Axial position of the housing thread
Rα 45 ° Angular position of the housing thread
Grease fitting
DN 0.259 in Diameter of head sphere of grease
fitting
SWN0.437 in Hexagonal key size for the grease fitting
GN 1/8-27 Thread of grease fitting
NPT
Calculation data
Basic dynamic load rating C 7 891 lbf
Basic static load rating C0 5 216 lbf
Fatigue load limit Pu 220 lbf
Limiting speed 3 300 r/min
Limiting speed with shaft tolerance h6
Mass
Mass bearing unit 5.952 lb
Mounting information
Set screw G2 M10x1.25
Hexagonal key size for set screw 0.2 in
Recommended tightening torque for set screw 146.037 lbf·in
Recommended diameter for attachment bolts, mm G 16.002 mm
Recommended diameter for attachment bolts, inch G 0.625 in
Generated from www.skf.com on 2024-01-27 Page 4 of 5
Terms and conditions
By accessing and using this website / app owned and published by AB SKF (publ.)
(556007-3495 · Gothenburg) (“SKF”), you agree to the following terms and conditions:
Warranty Disclaimer and Limitation of Liability
Although every care has been taken to assure the accuracy of the information on this website / app, SKF
provides this information "AS IS" and DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. You acknowledge that your use of this website / app is at your sole risk, that you assume full
responsibility for all costs associated with use of this website / app, and that SKF shall not be liable for any
direct, incidental, consequential, or indirect damages of any kind arising out of your access to, or use of the
information or software made available on this website / app. Any warranties and representations in this
website / app for SKF products or services that you purchase or use will be subject to the agreed upon terms
and conditions in the contract for such product or service. Further, for non-SKF websites / apps that are
referenced in our website / app or where a hyperlink appears, SKF makes no warranties concerning the
accuracy or reliability of the information in these websites / apps and assumes no responsibility for material
created or published by third parties contained therein. In addition, SKF does not warrant that this website /
app or these other linked websites / apps are free from viruses or other harmful elements.
Third Party Services
When viewing YouTube content via the SKF website(s) (i.e. using YouTube API Services), you agree to be
bound by the YouTube Terms of Service.
Copyright
Copyright in this website / app copyright of the information and software made available on this website /
app rest with SKF or its licensors. All rights are reserved. All licensed material will reference the licensor that
has granted SKF the right to use the material. The information and software made available on this website /
app may not be reproduced, duplicated, copied, transferred, distributed, stored, modified, downloaded or
otherwise exploited for any commercial use without the prior written approval of SKF. However, it may be
reproduced, stored and downloaded for use by individuals without prior written approval of SKF. Under no
circumstances may this information or software be supplied to third parties.
This website /app includes certain images used under license from Shutterstock, Inc.
Trademarks and Patents
All trademarks, brand names, and corporate logos displayed on the website / app are the property of SKF or
its licensors, and may not be used in any way without prior written approval by SKF. All licensed trademarks
published on this website / app reference the licensor that has granted SKF the right to use the trademark.
Access to this website / app does not grant to the user any license under any patents owned by or licensed to
SKF.
Changes
SKF reserves the right to make changes or additions to this website / app at any time.
Generated from www.skf.com on 2024-01-27 Page 5 of 5
