Data sheet

Three-phase monitoring relays CM-PAS

CM-PAS.31 and CM-PAS.41

The three-phase monitoring relays CM-PAS.x1

monitor the phase parameters phase sequence,
phase failure as well as phase unbalance.
All devices are available with two different terminal
versions. You can choose between the proven
screw connection technology (double-chamber
cage connection terminals) and the completely
tool-free Easy Connect Technology (push-in

2CDC 251 063 V0011

terminals).

Characteristics Approvals
–– Monitoring of three-phase mains for phase sequence, A UL 508, CAN/CSA C22.2 No.14
phase failure, phase unbalance
C GL
–– TRMS measuring principle
–– Threshold value for phase unbalance is adjustable as D GOST
absolute value K CB scheme pending
–– Tripping delay Tv adjustable or switched off by means of a
E CCC
logarithmic scale (0 s; 0,1-30 s)
–– ON-delayed tripping delay L RMRS
–– Powered by the measuring circuit
–– Precise adjustment by front-face operating controls
–– Screw connection technology or Marks
Easy Connect Technology available
a CE
–– Housing material for highest fire protection classification
UL 94 V-0 b C-Tick
–– Tool-free mounting on DIN rail as well as demounting
–– 2 c/o (SPDT) contacts
–– 22.5 mm (0.89 in) width
–– 3 LEDs for the indication of operational states
 Order data

Three-phase monitoring relays

Type Rated control supply voltage = measuring voltage Connection technology Order code

CM-PAS.31P 3 x 160-300 V AC Push-in terminals 1SVR 740 774 R1300

CM-PAS.31S Screw terminals 1SVR 730 774 R1300
CM-PAS.41P 3 x 300-500 V AC Push-in terminals 1SVR 740 774 R3300
CM-PAS.41S Screw terminals 1SVR 730 774 R3300

Accessories
Type Description Order code
ADP.01 Adapter for screw mounting 1SVR 430 029 R0100
MAR.01 Marker label for devices without DIP switches 1SVR 366 017 R0100
COV.11 Sealable transparent cover 1SVR 730 005 R0100

2 - Three-phase monitoring relays CM-PAS | Data sheet

 Connection technology
Maintenance free Easy Connect Technology with Approved screw connection technology with
push-in terminals double-chamber cage connection terminals
Type designation CM-xxS.yyP Type designation CM-xxS.yyS
2CDC 253 026 F0011

2CDC 253 025 F0011

Push-in terminals Double-chamber cage connection terminals

–– Tool-free connection of rigid and flexible wires with –– Terminal spaces for different wire sizes:
wire end ferrule according to DIN 46228-1-A, fine‑strand with/without wire end ferrule:
DIN 46228-4-E 1 x 0.5-2.5 mm² (2 x 20 - 14 AWG),
Wire size: 2 x 0.5-1.5 mm², (2 x 20 - 16 AWG) 2 x 0.5-1.5 mm² (2 x 20 - 16 AWG)
–– Easy connection of flexible wires without wire end rigid:
ferrule by opening the terminals 1 x 0.5-4 mm² (1 x 20 - 12 AWG),
–– No retightening necessary 2 x 0.5-2.5 mm² (2 x 20 - 14 AWG)
–– One operation lever for opening both connection –– One screw for opening and closing of both cages
terminals –– Pozidrive screws for pan- or crosshead screwdrivers
–– For triggering the lever and disconnecting of wires according to DIN ISO 2380-1 Form A 0.8 x 4 mm
you can use the same tool (Screwdriver according to (0.0315 x 0.157 in), DIN ISO 8764-1 PZ1 ø 4.5 mm
DIN ISO 2380-1 Form A 0.8 x 4 mm (0.0315 x 0.157 (0.177 in)
in), DIN ISO 8764-1 PZ1 ø 4.5 mm (0.177 in))
–– Constant spring force on terminal point independent
of the applied wire type, wire size or ambient
conditions (e. g. vibrations or temperature changes)
–– Opening for testing the electrical contacting
–– Gas-tight

Both the Easy Connect Technology with push-in terminals and screw connection technology with double-chamber cage
connection terminals have the same connection geometry as well as terminal position.

Data sheet | Three-phase monitoring relays CM-PAS - 3

 Functions

Operating controls

1 Adjustment of the threshold value Asym. for phase unbalace

2 Adjustment of the tripping delay Tv

3 Indication of operational states

R/T: red LED – Relay status / timing

F1: yellow LED – Fault message

F2: yellow LED – Fault message

1
4 Marker label
2CDC 251 063 V0011

Application
The three-phase monitoring relays CM-PAS.x1 are designed for use in three-phase mains for monitoring the phase
parameters phase sequence, phase failure as well as phase unbalance.
The CM-PAS.x1 provide an adjustable ON-delay and work according to the closed-circuit principle.

Operating mode
The CM-PAS.x1 have 2 c/o (SPDT) contacts and are available for 3-wire AC systems. The units are adjusted with front-
face operating controls. Potentiometers, with direct reading scale, allow the adjustment of the threshold value for phase
unbalance (Asym %) and the tripping delay Tv. The tripping delay Tv is adjustable over a range of instantaneous to a 30 s
delay. Timing is displayed by a flashing yellow LED labelled R/T.

Adjustment potentiometer

Threshold values
By means of three separate potentiometers with direct reading scales, the threshold values for over- and undervoltage as
well as for phase unbalance can be adjusted within the measuring range.
Measuring range for phase unbalance
CM-PAS.31
2-25 % of average of phase voltages
CM-PAS.41

Tripping delay Tv
The tripping delay Tv can be adjusted within a range of 0.1 to 30 s by means of a potentiometer with logarithmic scale.
By turning to the left stop, the tripping delay can be switched off.

4 - Three-phase monitoring relays CM-PAS | Data sheet

Indication of operational states

LEDs, status information and fault messages

Operational state R/T: LED yellow F1: LED red F2: LED red
Control supply voltage applied,
V - -
output relay energized
Tripping delay Tv active W - -
Phase failure - V W
Phase sequence - W alternating
Phase unbalance - V V

Function descriptions / diagrams

Phase sequence and phase failure monitoring

Applying control supply voltage begins the fixed start-up delay Ts. When Ts is complete and all phases are present with
correct voltage, the output relays energize and the yellow LED R/T is on.

Phase sequence monitoring:

The output relays de-energize as soon as a phase sequence error occurs. The fault is displayed by alternated flashing of
the LEDs F1 and F2. The output relays re-energize automatically as soon as the phase sequence is correct again.

Phase failure monitoring:

The output relays de-energize instantaneously if a phase failure occurs. The fault is indicated by lightning of LED F1 and
flashing of LED F2. The output relays re-energize automatically as soon as the voltage returns to the tolerance range.

L1, L2, L3
2CDC 252 094 F0207

Measured value L1, L2, L3 L1, L3, L2 L1, L2, L3 L1, L2 L1, L2, L3 L1 L1, L2, L3

Ts L3 L2, L3

15-18
15-16
25-28
25-26

F1: red LED

2CDC 252 094 F0207

F2: red LED

R/T: yellow LED
Ts = start-up delay fixed 200 ms

Data sheet | Three-phase monitoring relays CM-PAS - 5

 Phase unbalance monitoring
Applying control supply voltage begins the fixed start-up delay Ts. When Ts is complete and all phases are present with
correct voltage and with correct phase sequence, the output relays energize and the yellow LED R/T is on.
If the voltage to be monitored exceeds or falls below the set phase unbalance threshold value, the output relays
de-energize after the set tripping delay Tv is complete. The LED R/T flashes during timing and turns off as soon as the
output relays de-energize.
The output relays re-energize automatically as soon as the voltage returns to the tolerance range, taking into account a
fixed hysteresis of 20 %. The LED R/T is on.

L1, L2, L3

2CDC 252 092 F0207

Unbalance
L3
Unbalance - Hysteresis

Measured value
L1, L2, L3 L1, L2
Unbalance + Hysteresis
Unbalance
Ts Tv <Tv Tv
15-18
15-16
25-28
25-26

F1: red LED

2CDC 252 092 F0207

F2: red LED
R/T: yellow LED
Ts = start-up delay fixed 200 ms
Tv = adjustable tripping delay

Electrical connection
L1, L2, L3 Control supply voltage = measuring voltage
L1 L2 L3
15-16/18 Output contacts - closed-circuit principle
25-26/28
L1 L2 L3 15 25

16 18 26 28
2CDC 252 037 F0008

26 25 28
16 15 18

Connection diagram CM-PAS.31 and CM-PAS.41

6 - Three-phase monitoring relays CM-PAS | Data sheet

Technical data
Data at Ta = 25 °C and rated values, unless otherwise indicated

Input circuit
Type CM-PAS.31 CM-PAS.41
Supply circuit = measuring circuit L1, L2, L3
Rated control supply voltage Us = measuring voltage 3 x 160-300 V AC 3 x 300-500 V AC
Rated control supply voltage Us tolerance -15...+10 %
Rated frequency 50/60 Hz
Frequency range 45-65 Hz
Typical current / power consumption 25 mA / 10 VA (230 V AC) 25 mA / 18 VA (400 V AC)

Measuring circuit L1, L2, L3

Monitoring functions Phase failure J J
Phase sequence J J
Phase unbalance J J
Measuring range Phase unbalance 2-25 % of average of phase voltages
Thresholds Phase unbalance (switch-off value) adjustable within measuring range
Hysteresis related to
Phase unbalance fixed 20 %
the threshold value
Rated frequency of the measuring signal 50/60 Hz
Frequency range of the measuring signal 45-65 Hz
Maximum measuring cycle time 100 ms
Accuracy within the rated control supply voltage tolerance DU  0.5 %
Accuracy within the temperature range DU  0.06 % / °C
Measuring method True RMS

Timing circuit
Start-up delay Ts fixed 200 ms
Tripping delay Tv ON-delay
0 s; 0.1-30 s adjustable
Repeat accuracy (constant parameters) < w0.2 %
Accuracy within the rated control supply voltage tolerance Dt  0.5 %
Accuracy within the temperature range Dt  0.06 % / °C

User interface
Indication of operational states
Relay status / timing R/T yellow LED
Fault message F1 red LED
Fault message F2 red LED

Details see table ‚LEDs, status information and fault messages‘ on page 5 and ‚Function descriptions / diagrams‘ on page 5.

Data sheet | Three-phase monitoring relays CM-PAS - 7

 Output circuits
Kind of output 15-16/18 relay, 1st c/o (SPDT) contact
25-26/28 relay, 2nd c/o (SPDT) contact
1 x 2 (SPDT) contacts
Operating principle closed-circuit principle 1)

Contact material AgNi alloy, Cd free

Rated operational voltage Ue (IEC/EN 60947-1) 250 V
Minimum switching voltage / Minimum switching current 24 V / 10 mA
Maximum switching voltage / Maximum switching current see load limit curves
Rated operational current Ie AC12 (resistive) at 230 V 4A
(IEC/EN 60947-5-1) AC15 (inductive) at 230 V 3A
DC12 (resistive) at 24 V 4A
DC13 (inductive) at 24 V 2A
AC rating (UL 508) Utilization category
B 300
(Control Circuit Rating Code)
max. rated operational voltage 300 V AC
max. continuous thermal current at B 300 5A
max. making/breaking apparent power
3600/360 VA
at B 300
Mechanical lifetime 30 x 106 switching cycles
Electrical lifetime AC12, 230 V, 4 A 0.1 x 106 switching cycles
Maximum fuse rating to achieve n/c contact 6 A fast-acting
short-circuit protection n/o contact 10 A fast-acting

General data

MTBF on request
Duty time 100 %
Dimensions (W x H x D) product dimensions 22.5 x 85.6 x 103.7 mm (0.89 x 3.37 x 4.08 in)
packaging dimensions 97 x 109 x 30 mm (3.82 x 4.29 x 1.18 in)
Weight Screw connection technology Easy Connect Technology (push-in)
net weight CM-PAS.31 0.133 kg (0.293 lb) 0.124 kg (0.273 lb)
CM-PAS.41 0.132 kg (0.291 lb) 0.123 kg (0.271 lb)
gross weight CM-PAS.31 0.158 kg (0.348 lb) 0.149 kg (0.328 lb)
CM-PAS.41 0.157 kg (0.346 lb) 0.148 kg (0.326 lb)
Mounting DIN rail (IEC/EN 60715), snap-on mounting without any tool
Mounting position any
CM-PAS.31 CM-PAS.41
Minimum distance to other units horizontal 10 mm (0.39 in) in case of continuous voltage of ...
> 220 V > 400 V
Material of housing UL 94 V-0
Degree of protection housing IP50
terminals IP20

1) Closed-circuit principle: Output relay(s) de-energize(s) if measured value exceeds or falls below the adjusted threshold value.

8 - Three-phase monitoring relays CM-PAS | Data sheet

Electrical connection
Screw connection Easy Connect
technology Technology (push-in)
Wire size fine‑strand with(out) 1 x 0.5-2.5 mm² 2 x 0.5-1.5 mm²
wire end ferrule (1 x 20-14 AWG) (2 x 20-16 AWG)
2 x 0.5-1.5 mm²
(2 x 20-16 AWG)
rigid 1 x 0.5-4 mm² 2 x 0.5-1.5 mm²
(1 x 20-12 AWG) (2 x 20-16 AWG)
2 x 0.5-2.5 mm²
(2 x 20-14 AWG)
Stripping length 8 mm (0.32 in)
Tightening torque 0.6 - 0.8 Nm -
(5.31 - 7.08 lb.in)

Environmental data
Ambient temperature ranges operation -25...+60 °C
storage -40...+85 °C
Damp heat, cyclic (IEC/EN 60068-2-30) 55 °C, 6 cycles
Climatic category 3K3
Vibration, sinusoidal (IEC/EN 60255-21-1) Class 2
Shock (IEC/EN 60255-21-2) Class 2

Isolation data
Type
Rated insulation input circuit / output circuit 600 V
voltage Ui output circuit 1 / output circuit 2 300 V
Rated impulse withstand voltage Uimp input circuit 6 kV, 1.2/50 µs
(IEC/EN 60664) output circuit 4 kV, 1.2/50 µs
Test voltage between all isolated circuits (routine test) 2.5 kV, 50 Hz, 1 s
Basic insulation input circuit / output circuit 600 V
Protective separation input circuit /
-
(IEC/EN 61140, EN 50178) output circuit
Pollution degree (IEC/EN 60664, IEC/EN 60255-5) 3
Overvoltage category (IEC/EN 60664, IEC/EN 60255-5) III

Standards
Product standard IEC/EN 60255-6, EN 50178
Low Voltage Directive 2006/95/EC
EMC directive 2004/108/EC
RoHS directive 2002/95/EC

Data sheet | Three-phase monitoring relays CM-PAS - 9

 Electromagnetic compatibility
Type
Interference immunity to IEC/EN 61000-6-1, IEC/EN 61000-6-2
electrostatic discharge IEC/EN 61000-4-2 Level 3 (6 kV / 8 kV)
radiated, radio-frequency, IEC/EN 61000-4-3 Level 3 (10 V/m)
electromagnetic field
electrical fast transient / burst IEC/EN 61000-4-4 Level 3 (2 kV / 2 kHz)
surge IEC/EN 61000-4-5 Level 4 (2 kV L-L)
conducted disturbances, induced by IEC/EN 61000-4-6 Level 3 (10 V)
radio-frequency fields
harmonics and interharmonics IEC/EN 61000-4-13 Class 3
Interference emission IEC/EN 61000-6-3, IEC/EN 61000-6-4
high-frequency radiated IEC/CISPR 22, Class B
EN 55022
high-frequency conducted IEC/CISPR 22, Class B
EN 55022

Technical diagrams

Load limit curves

V V
300 300
V 200 V 200
resistive load
resistive load
100 100
80 80
60 60
50 50
40 40
30 30
20 20
2CDC 252 194 F0205

2CDC 252 193 F0205

10 10
0.1 0.2 0.5 1 2 4 6 10 0.1 0.2 0.5 1 2 4 6 10
I A I A

AC load (resistive) DC load (resistive)

1.0
Switching cycles

0.9

0.8
F
0.7 250 V
resistive load
0.6

0.5
2CDC 252 192 F0205

0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
cos ϕ
2CDC 252 148 F0206

Derating factor F for inductive AC load

Switching current [A]

Contact lifetime

10 - Three-phase monitoring relays CM-PAS | Data sheet

Dimensions
in mm and inches

113.4 4.47”
105.9 4.17” 22.5 0.89”

85.6 3.37”

2CDC 252 009 F0011

103.7 4.08”

Accessories
in mm and inches

8 0.32”
22.5 0.89” 4.8 0.19”

68 2.68”
0.453”
11.5
0.256”

62.5 2.461”
6.5

0.315”
2CDC 252 008 F0010

2CDC 252 186 F0005

2CDC 252 010 F0011

0.394”

0.787”

3A11
8
10

20

60 2.362” 20 front to back

110.5 4.31”
70 2.756” 0.787”
ADP.01 ‑ Adapter for screw mounting MAR.01 ‑ Marker label for devices COV.11 ‑ Sealable transparent cover
without DIP switches

Further documentation

Document title Document type Document number

Electronic products and relays Technical catalogue 2CDC 110 004 C020x
CM-PAS, CM-PFS, CM-PSS, CM-PVS Instruction manual 1SVC 730 510 M0000

You can find the documentation on the internet at www.abb.com/lowvoltage -> Control Products ->
Electronic Relays and Controls -> Three Phase Monitors.

Data sheet | Three-phase monitoring relays CM-PAS - 11

Contact us

ABB STOTZ-KONTAKT GmbH

Document number 2CDC 112 180 D0201 (07.2012)

P. O. Box 10 16 80
69006 Heidelberg, Germany
Phone: +49 (0) 6221 7 01-0
Fax: +49 (0) 6221 7 01-13 25
E-mail: [email protected]

You can find the address of your

local sales organisation on the
ABB home page
http://www.abb.com/contacts
-> Low Voltage Products and Systems

Note:
We reserve the right to make technical changes
or modify the contents of this document without
prior notice. With regard to purchase orders, the
agreed particulars shall prevail. ABB AG does
not accept any responsibility whatsoever for
potential errors or possible lack of information in
this document.

We reserve all rights in this document and in

the subject matter and illustrations contained
therein. Any reproduction, disclosure to third
parties or utilization of its contents – in whole
or in parts – is forbidden without prior written
consent of ABB AG.

Copyright© 2012 ABB

All rights reserved