BACnet Gateway-3

Installation and Operation Manual

A
Document 53372
5/6/09 Rev:
P/N: 53372:A ECN: 08-717
Fire Alarm System Limitations
While a fire alarm system may lower insurance rates, it is not a substitute for fire insurance!
An automatic fire alarm system—typically made up of smoke detec- bedrooms), smoking in bed, and violent explosions (caused by escap-
tors, heat detectors, manual pull stations, audible warning devices, ing gas, improper storage of flammable materials, etc.).
and a fire alarm control panel with remote notification capability—can Heat detectors do not sense particles of combustion and alarm only
provide early warning of a developing fire. Such a system, however, when heat on their sensors increases at a predetermined rate or
does not assure protection against property damage or loss of life reaches a predetermined level. Rate-of-rise heat detectors may be
resulting from a fire. subject to reduced sensitivity over time. For this reason, the rate-of-
The Manufacturer recommends that smoke and/or heat detectors be rise feature of each detector should be tested at least once per year
located throughout a protected premise following the recommenda- by a qualified fire protection specialist. Heat detectors are designed to
tions of the current edition of the National Fire Protection Association protect property, not life.
Standard 72 (NFPA 72), manufacturer's recommendations, State and IMPORTANT! Smoke detectors must be installed in the same room
local codes, and the recommendations contained in the Guide for as the control panel and in rooms used by the system for the connec-
Proper Use of System Smoke Detectors, which is made available at tion of alarm transmission wiring, communications, signaling, and/or
no charge to all installing dealers. These documents can be found at power. If detectors are not so located, a developing fire may damage
[Link] the alarm system, crippling its ability to report a fire.
A study by the Federal Emergency Management Agency (an agency Audible warning devices such as bells may not alert people if these
of the United States government) indicated that smoke detectors may devices are located on the other side of closed or partly open doors or
not go off in as many as 35% of all fires. While fire alarm systems are are located on another floor of a building. Any warning device may fail
designed to provide early warning against fire, they do not guarantee to alert people with a disability or those who have recently consumed
warning or protection against fire. A fire alarm system may not provide drugs, alcohol or medication. Please note that:
timely or adequate warning, or simply may not function, for a variety
of reasons: • Strobes can, under certain circumstances, cause seizures in people
with conditions such as epilepsy.
Smoke detectors may not sense fire where smoke cannot reach the
• Studies have shown that certain people, even when they hear a fire
detectors such as in chimneys, in or behind walls, on roofs, or on the
alarm signal, do not respond or comprehend the meaning of the signal.
other side of closed doors. Smoke detectors also may not sense a fire
It is the property owner's responsibility to conduct fire drills and other
on another level or floor of a building. A second-floor detector, for training exercise to make people aware of fire alarm signals and
example, may not sense a first-floor or basement fire. instruct them on the proper reaction to alarm signals.
Particles of combustion or “smoke” from a developing fire may not • In rare instances, the sounding of a warning device can cause tempo-
reach the sensing chambers of smoke detectors because: rary or permanent hearing loss.
• Barriers such as closed or partially closed doors, walls, or chimneys A fire alarm system will not operate without any electrical power. If
may inhibit particle or smoke flow. AC power fails, the system will operate from standby batteries only for
• Smoke particles may become “cold,” stratify, and not reach the ceiling a specified time and only if the batteries have been properly main-
or upper walls where detectors are located. tained and replaced regularly.
• Smoke particles may be blown away from detectors by air outlets. Equipment used in the system may not be technically compatible
• Smoke particles may be drawn into air returns before reaching the with the control panel. It is essential to use only equipment listed for
detector. service with your control panel.
The amount of “smoke” present may be insufficient to alarm smoke Telephone lines needed to transmit alarm signals from a premise to a
detectors. Smoke detectors are designed to alarm at various levels of central monitoring station may be out of service or temporarily dis-
smoke density. If such density levels are not created by a developing abled. For added protection against telephone line failure, backup
fire at the location of detectors, the detectors will not go into alarm. radio transmission systems are recommended.
Smoke detectors, even when working properly, have sensing limita- The most common cause of fire alarm malfunction is inadequate
tions. Detectors that have photo-electronic sensing chambers tend to maintenance. To keep the entire fire alarm system in excellent work-
detect smoldering fires better than flaming fires, which have little visi- ing order, ongoing maintenance is required per the manufacturer's
ble smoke. Detectors that have ionizing-type sensing chambers tend recommendations, and UL and NFPA standards. At a minimum, the
to detect fast-flaming fires better than smoldering fires. Because fires requirements of NFPA 72 shall be followed. Environments with large
develop in different ways and are often unpredictable in their growth, amounts of dust, dirt or high air velocity require more frequent mainte-
neither type of detector is necessarily best and a given type of detec- nance. A maintenance agreement should be arranged through the
tor may not provide adequate warning of a fire. local manufacturer's representative. Maintenance should be sched-
uled monthly or as required by National and/or local fire codes and
Smoke detectors cannot be expected to provide adequate warning of should be performed by authorized professional fire alarm installers
fires caused by arson, children playing with matches (especially in

2 BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09

Installation Precautions
Adherence to the following will aid in problem-free installation with long-term reliability:
WARNING - Several different sources of power can be connected to Like all solid state electronic devices this system may operate errati-
the fire alarm control panel. Disconnect all sources of power before cally or can be damaged when subjected to lightning-induced tran-
servicing. The control unit and associated equipment may be dam- sients. Although no system is completely immune from lightning
aged by removing and/or inserting cards, modules, or interconnecting transients and interferences, proper grounding will reduce susceptibil-
cables while the unit is energized. Do not attempt to install, service, ity. Overhead or outside aerial wiring is not recommended, due to an
or operate this unit until this manual is read and understood. increased susceptibility to nearby lightning strikes. Consult with the
CAUTION - System Reacceptance Test after Software Changes. To Technical Services if any problems are anticipated or encountered.
ensure proper system operation, this product must be tested in accor- Disconnect AC power and batteries prior to removing or inserting cir-
dance with NFPA 72 after any programming operation or change in cuit boards. Failure to do so can damage circuits.
site-specific software. Reacceptance testing is required after any Remove all electronic assemblies prior to any drilling, filing, reaming,
change, addition or deletion of system components, or after any mod- or punching of the enclosure. When possible, make all cable entries
ification, repair or adjustment to system hardware or wiring. from the sides or rear. Before making modifications, verify that they
All components, circuits, system operations, or software functions will not interfere with battery, transformer, and printed circuit board
known to be affected by a change must be 100% tested. In addition, location.
to ensure that other operations are not inadvertently affected, at least Do not tighten screw terminals more than 9 in-lbs. Over-tightening
10% of initiating devices that are not directly affected by the change, may damage threads, resulting in reduced terminal contact pressure
up to a maximum of 50 devices, must also be tested and proper sys- and difficulty with screw terminal removal.
tem operation verified.
Though designed to last many years, system components can fail at
This system meets NFPA requirements for operation at 0°C to 49°C any time. This system contains static-sensitive components. Always
(32°F to 120°F) and at a relative humidity 93% ± 2% RH (non-con- ground yourself with a proper wrist strap before handling any circuits
densing) at 32°C ± 2°C (90°F ± 3°F). However, the useful life of the so that static charges are removed from the body. Use static-sup-
system's standby batteries and the electronic components may be pressive packaging to protect electronic assemblies removed from
adversely affected by extreme temperature ranges and humidity. the unit.
Therefore, it is recommended that this system and all peripherals be
installed in an environment with a nominal room temperature of 15- Follow the instructions in the installation, operating, and program-
27° C/60-80° F. ming manuals. These instructions must be followed to avoid damage
to the control panel and associated equipment. FACP operation and
Verify that wire sizes are adequate for all initiating and indicating reliability depend upon proper installation by authorized personnel.
device loops. Most devices cannot tolerate more than a 10% I.R.
drop from the specified device voltage.

FCC Warning
WARNING: This equipment generates, uses, and can radi- Canadian Requirements: This digital apparatus does not
ate radio frequency energy and if not installed and used in exceed the Class A limits for radiation noise emissions
accordance with the instruction manual, may cause inter- from digital apparatus set out in the Radio Interference
ference to radio communications. It has been tested and Regulations of the Canadian Department of Communica-
found to comply with the limits for class A computing tions. This Class A digital apparatus complies with Cana-
device pursuant to Subpart B of Part 15 of FCC Rules, dian ICES-003.
which is designed to provide reasonable protection against Le present appareil numerique n'emet pas de bruits radio-
such interference when operated in a commercial environ- electriques depassant les limites applicables aux appareils
ment. Operation of this equipment in a residential area is numeriques de la classe A prescrites dans le Reglement
likely to cause interference, in which case the user will be sur le brouillage radioelectrique edicte par le ministere des
required to correct the interference at his own expense. Communications du Canada. Cet appareil numerique de la
classe A est conforme a la norme NMB-003 du Canada.

Acclimate Plus™, HARSH™, NOTI•FIRE•NET™, VeriFire™, NION™, NOTIFER Intergrated Systems™ and ONYXWorks™ are trademarks, and
ONYX®, FlashScan®, UniNet®, VIEW®, NOTIFIER® are registered trademarks of Honeywell. Simplex® is registered trademark of Tyco
International Ltd. Echelon® is a registered trademark and LonWorks™ is a trademark of Echelon Corporation. ARCNET® is a registered trademark of Datapoint
Corporation. Microsoft® and Windows® are registered trademarks of the Microsoft Corporation. LEXAN® is a registered trademark of GE Plastics, a subsidiary of
General Electric Company.
© 2009 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited.

BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09 3

Documentation Feedback
Your feedback helps us keep our documentation up-to-date and accurate. If you have any comments, you can email
us.
Please include the following information:
• Product name and version number (if applicable)
• Manual page number
• Your comment
Send email messages to:
[Link]@[Link]
Please note this email address is for documentation feedback only. If you have any technical issues, please contact
Technical Services.

4 BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09

 Table of Contents
Section 1 NOTIFIER® BACnet Gateway-3 Features .............................................................. 7
1.1: Product Description .......................................................................................................................................7
1.1.1: BACnet GW-3 Features.......................................................................................................................7
1.2: Related Documentation .................................................................................................................................8
Table 1.1 Related Documentation ..........................................................................................................8
1.3: Agency Listings .............................................................................................................................................8
1.3.1: Compliance..........................................................................................................................................8
1.3.2: Installation ...........................................................................................................................................9
1.4: Environmental Requirements ........................................................................................................................9
1.5: Compatibility ..............................................................................................................................................10
1.6: Upgrade Information ...................................................................................................................................10
1.7: System Requirements ..................................................................................................................................10
1.8: System Architecture.....................................................................................................................................11
1.8.1: Single Panel Architecture ..................................................................................................................11
Figure 1.1 BACnet GW-3 Single Panel Diagram ................................................................................11
1.8.2: NFN Network Architecture ...............................................................................................................11
Figure 1.2 Notifier System Example 1- A Single NFN Network.........................................................12
Figure 1.3 Notifier System Example 2 - Multiple NFN Networks ......................................................13
Section 2 BACnet GW-3 Embedded Installation .................................................................. 15
2.1: Required Equipment ....................................................................................................................................15
2.2: BACnet GW-3 Installation Overview..........................................................................................................16
2.2.1: Gateway Installation Process Overview Flow Diagram....................................................................16
Figure 2.1 Gateway Installation Process Flow Diagram ......................................................................16
2.2.2: BACnet GW-3 Board Layout ............................................................................................................17
Figure 2.2 BACnet GW-3 Board..........................................................................................................17
2.3: Installing a CAB3/CAB4 Cabinet ...............................................................................................................18
Figure 2.3 CAB-3/CAB-4 Series Installation Document, 15330 .........................................................18
2.4: Installing a CHS-4L Chassis........................................................................................................................19
Figure 2.4 Installing a Chassis..............................................................................................................19
2.5: Installing the BACnet GW-3 Board.............................................................................................................20
Figure 2.5 Install BACnet GW-3 Board onto Chassis .........................................................................20
2.5.1: BACnet GW-3 Power Supply Connection .......................................................................................20
Table 2.1 Power Supply Specifications................................................................................................20
Figure 2.6 BACnet GW-3 Power Connection......................................................................................21
2.5.2: Wiring Restrictions............................................................................................................................21
2.5.3: Installing the Network Communication Module ...............................................................................22
Table 2.2 Network Communication Module Details ...........................................................................22
Figure 2.7 HS-NCM Installation Document PN 54014 .......................................................................22
Figure 2.8 NCM Installation Document
PN 51533 ..............................................................................................................................................22
2.6: Connecting BACnet GW-3 to an IP Network..............................................................................................23
Figure 2.9 IP Cable Connection .........................................................................................................23
2.7: Connecting BACnet GW-3 to an NFN Network or High Speed NFN Network .........................................23
Section 3 BACnet GW-3 Configuration and Operation ....................................................... 25
3.1: BACnet GW-3 Configuration ......................................................................................................................25
3.1.1: BACnet GW-3 Configuration Overview...........................................................................................25
3.1.2: BACNet Gateway Configuration Tool Installation ...........................................................................25
3.1.3: Connect the Configuration Computer to the BACnet GW-3 ............................................................26
3.1.4: Prepare the Configuration Computer to Communicate with BACnet GW-3....................................26
3.1.5: Log into the BACnet GW-3 for Configuration .................................................................................27
3.1.6: Configure the BACnet GW-3 ............................................................................................................28
3.1.7: Viewing BACnet GW-3 Activity with the BACNet Gateway Configuration Tool ..........................33
3.2: Connect the BACnet GW-3 to the NFN Network or FACP ........................................................................33
BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09 5
Table of Contents

Table 3.1 BACnet GW-3 to Fire System Connection Options.............................................................34

3.2.1: Connecting BACnet GW-3 to a High Speed NFN Network Control Module ..................................35
Figure 3.1 USB Connection..................................................................................................................35
Figure 3.2 NUP to NUP Connection ....................................................................................................36
3.2.2: Connecting BACnet GW-3 to an NFN Network Control Module ....................................................37
Figure 3.3 NUP to NUP Connection ....................................................................................................37
3.2.3: Connecting BACnet GW-3 Directly to a Fire Alarm Control Panel .................................................38
Figure 3.4 NUP to NUP Connection ....................................................................................................38
3.3: Back Up BACnet GW-3...............................................................................................................................38
3.4: Restore BACnet GW-3 ................................................................................................................................39
3.5: BACnet GW-3 Operation.............................................................................................................................40
3.5.1: About BACnet GW-3 Start Up..........................................................................................................40
Appendix A: PIC Statement ................................................................................................... 41
A.1: BACnet Protocol Implementation Conformance Statement (Normative) ..................................................41
Appendix B: BACnet GW-3 Compatible Node Types .......................................................... 47
B.1: Direct Connect Node Type Compatibility...................................................................................................47
Table B.1 Panel Communication Connection Table ............................................................................47
Appendix C: BACnet GW-3 Local Configuration ................................................................. 49
C.1: Direct Connection to the Gateway Board ...................................................................................................49
Figure C.1 Configuration Computer Direct Connection ......................................................................49
Table C.1 Cross Over Cable (568B).....................................................................................................50
Appendix D: Glossary ............................................................................................................ 51
Index ........................................................................................................................................ 53

6 BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09

 Section 1 NOTIFIER® BACnet Gateway-3 Features

1.1 Product Description

The NOTIFIER® BACnet Gateway-3 (BACnet GW-3) provides a communication link between
networks that use the BACnet communication protocol and Fire Alarm Control Panels (FACP)
resident on an NFN network or high speed NFN network. The BACnet GW-3 acts like any other
node on an NFN network or high speed NFN network. The NFN network communicates with the
gateway through an HS-NCM-W/SF/MF or NCM-W/F network control module that is on that NFN
network or through a direct connection to a single NOTIFIER® panel. The BACnet
communication protocol is an American National Standard (ANSI/ASHRAE 135-1995).
The BACnet GW-3 application represents physical fire devices as BACnet objects and manages the
object database. As events occur, the object properties are updated in real-time, and messages are
sent to the appropriate BACnet report destination (BACnet computer clients are computers with the
graphical user interface workstation front end). BACnet clients may make requests to read
properties of the BACnet objects. Those properties are the values of the device status and
programming. The user subscribes to Event Notification objects per FACP, and the BACnet device
receives events from objects on the FACP as a result of this subscription.
The BACnet client workstation front end must conform to BACnet Standard Annex J for IP and
support Device Objects, Binary Output Objects, and Multi-state Input or Life Safety Points/Zones.
It is also required to write to Notification Objects and receive confirmed/unconfirmed event
notification messages. For details, refer to Appendix A, “PIC Statement”, on page 41.
The BACnet GW-3 Configuration Tool, an offline programming utility that is included with the
BACnet GW-3 assembly when ordered, is used to configure the BACnet GW-3. It is installed onto
a computer that will be used to configure the gateway. Refer to “BACnet GW-3 Configuration” on
page 27.

1.1.1 BACnet GW-3 Features

Below are some of the features of the BACnet GW-3.
• Multiple Gateways can be used for large networks (greater than 15 panels/15,000 objects).
• Use of ethernet port for BACnet GW-3 configuration with the BACnet GW-3 Configuration
Tool.

NOTE: This manual is written with the understanding that its user is trained in BACnet operations
and services. The information provided here is solely for the configuration of the Gateway to
communicate event information to an existing BACnet network.

BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09 7

NOTIFIER® BACnet Gateway-3 Features Related Documentation

1.2 Related Documentation

Below is a list of documentation that relates to the use of the BACnet GW-3.

Table 1.1 Related Documentation

For information on Refer to Part No.

Compatible Devices Device Compatibility Document 15378

Cabinets & Chassis CAB-3/CAB-4 Series Installation Document 15330

Offline Programming Utility Veri•Fire™ Tools on-line help file VeriFire-TCD

Veri•Fire™ Medium Systems on-line help file VeriFire-CD

VeriFire-TCDNetworking NFN Manual 51584

NCM-W/F Installation Document 51533
HS-NCM-W/SF/MF Installation Document 54014
MIB Media Interface Board Manual 50255

Panels and Annunciators NFS-320 Installation/Operation/Programming Manual 52745/52746/52747

NFS-640 Installation/Operation/Programming Manual 52544/52545/52546
NFS2-640 Installation/Operation/Programming Manual 52741/52742/52743
NFS-3030 Installation/Operation/Programming Manual 51330/51344/51345
NFS2-3030 Installation/Operation/Programming Manual 52544/52546/52545
Network Control Annunciator (NCA) Manual 51482
Network Control Annunciator-2 (NCA-2) Manual 52482
Network Control Station (NCS) Manual 51095
AM2020/AFP1010 Installation, Operation, and Programming Manual 15088
DVC Series Digital Voice Command Manual 52411

1.3 Agency Listings

NOTE:
UL 864, 9th Edition—Notifier systems work with products that have been UL 864, 9th Edition
listed as well as products that have not received UL 864, 9th Edition certification. Operation of
systems that are comprised of equipment that is UL 864, 9th Edition listed together with products
that are not UL 864, 9th Edition listed requires the approval of the local Authority Having
Jurisdiction (AHJ).
CAN/ULC-S559-04, 1st Edition—Notifier systems work with products that have been CAN/ULC-
S559-04, 1st Edition listed as well as products that have not received CAN/ULC-S559-04, 1st
Edition certification. Operation of systems that are comprised of equipment that is CAN/ULC-
S559-04, 1st Edition listed together with products that are not CAN/ULC-S559-04, 1st Edition
listed requires the approval of the local Authority Having Jurisdiction (AHJ).

1.3.1 Compliance
This product has been investigated to, and found to be in compliance with the following standards.
National Fire Protection Association
• NFPA 72—National Fire Alarm Code
Underwriters Laboratories
• UL-864—Control Units for Fire Alarm Systems, Ninth Edition
• UL-2017—General-Purpose Signaling Devices and Systems, First Edition
Underwriters Laboratories Canada
• CAN/ULC-S527-99—Standard for Control Units for Fire Alarm Systems, Second Edition

8 BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09

Environmental Requirements NOTIFIER® BACnet Gateway-3 Features

• CAN/ULC-S559-04—Equipment for Fire Signal Receiving Centres and Systems, First

Edition

1.3.2 Installation
This product is intended to be installed in accordance with the following regulatory agencies.
Local
• AHJ—Authority Having Jurisdiction
National Fire Protection Association
• NFPA 70—National Electrical Code
• NFPA 72—National Fire Alarm Code
• NFPA 101—Life Safety Code
Underwriters Laboratories
• UL-1076—In certified applications, the unit shall be installed in accordance with Proprietary
Burglar Alarm Units and Systems, Fifth Edition
Underwriters Laboratories Canada
• C22.1–98—Canadian Electrical Code, Part I (Twentieth Edition), Safety Standard for
Electrical Installation
• CAN/ULC-S524-06—Standard for the installation of Fire Alarm Systems, Fifth Edition
• CAN/ULC-S561-03—Installation and Services for Fire Signal Receiving Centres and
Systems, First Edition

WARNING: Installation
! Improper installation, maintenance, and lack of routine testing could result in system malfunction.

About Ethernet Network Installations

“Listed for the purpose” has been formally interpreted by NFPA (Formal Interpretation 72-99-1)
for equipment on packet switched networks as being listed to the requirements applicable to
general purpose communications network equipment.
For ULC applications, the Internet cannot be used for either primary or ancillary functionality.
“Listed for the purpose” has been formally interpreted by NFPA (Formal Interpretation 72-99-1)
for equipment on packet switched networks as being listed to the requirements applicable to
general purpose communications network equipment.
For ULC applications, the Internet cannot be used for either primary or ancillary functionality.

1.4 Environmental Requirements

This product must be installed in the following environmental conditions:
• Temperature range of 0°C to 49°C (32°F - 120°F).
• 93% humidity non-condensing at 30°C (86°F).

The contents of this manual are important and must be kept in close proximity of the hardware. If
building ownership is changed, this manual and all other testing and maintenance information must
also be passed to the current owner of the facility. A copy of this manual was shipped with the
equipment and is also available from the manufacturer.

NOTE: Refer to Appendix A, “PIC Statement”, on page 41 for the BACnet PIC statement.

BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09 9

NOTIFIER® BACnet Gateway-3 Features Compatibility

1.5 Compatibility
NOTE: The BACnet GW-3 requires that at least one node on the NFN network be an ONYX
series panel. BACnet GW-3 does not run on an NFN network with no ONYX series panels.

Refer to Appendix B, “BACnet GW-3 Compatible Node Types”, on page 47 for supported panels
and annunciators.

1.6 Upgrade Information

Firmware for systems running BACnet GW-3 versions prior to 3.11 should not be upgraded unless
there is an ONYX series panel on the system. BACnet GW-3 does not run on an NFN network with
no ONYX series panels.

1.7 System Requirements

The BACnet GW-3 can monitor up to fifteen panels, but the combined object count across the
monitored panels cannot exceed 15,000 objects. This includes all detectors, monitor modules,
control modules, bell circuits, etc. Refer to the NFN network manual for details about wiring
limitations.
The computer on which the BACnet GW-3Configuration Tool is installed should be Windows 2000
or Window XP. The computer must communicate with the BACnet GW-3 over IP or through a
crossover cable from the BACnet GW-3 ethernet port.

10 BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09

System Architecture NOTIFIER® BACnet Gateway-3 Features

1.8 System Architecture

NOTE: The BACnet GW-3 client workstation is not intended as a primary annunciator and is ancillary
in nature.

These are connections options for the BACnet GW-3 architecture.

An Internet or Intranet IP network connection is used with both architectures.

1.8.1 Single Panel Architecture

Direct panel connection; a connection is made directly to a supported NOTIFIER® panel or
annunciator (Figure 1.1 on page 11). Refer to Appendix B, “BACnet GW-3 Compatible Node
Types”, on page 47 for supported panels and annunciators.

BACnet/IP Client with Workstation Front End

IP connection over
Ethernet

BACnet GW-3

NUP connection

FACP

Figure 1.1 BACnet GW-3 Single Panel Diagram

1.8.2 NFN Network Architecture

NFN network connection; a NUP connection is made to an NCM or HS-NCM board on the NFN
network as the BACnet GW-3 (Figure 1.2 on page 12)

BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09 11

NOTIFIER® BACnet Gateway-3 Features System Architecture

IP Network

BACnet/IP Client with Workstation Front End BACnet/IP Client with Workstation Front End

HS-NCM W/SF/MF
or
NCM W/F

BACnet GW-3

NFN Network

FACP FACP FACP

Figure 1.2 Notifier System Example 1- A Single NFN Network

12 BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09

System Architecture NOTIFIER® BACnet Gateway-3 Features

IP Network

Workstation/
PC Gateway
BACnet/IP Client with Workstation Front End

HS-NCM W/SF/MF
or
NCM W/F

Workstation/Echelon
Gateway

BACnet GW-3

Style 4 or 6 NION
Echelon
Network Wire NION
NFN Network or Fiber NFN Network
NION

FACP FACP FACP FACP FACP FACP

Figure 1.3 Notifier System Example 2 - Multiple NFN Networks

BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09 13

NOTIFIER® BACnet Gateway-3 Features System Architecture

14 BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09

 Section 2 BACnet GW-3 Embedded Installation
NOTE: The BACnet GW-3 is for ancillary use only and does not increase the burglary grade of service
for the system.

2.1 Required Equipment

The BACnet GW-3 requires the following:
BACnet GW-3 Assembly
The following are shipped with the BACnet GW-3:
• BACnet GW-3 board
• PNET-1 surge suppressor (P/N PNET-1)
• NUP to NUP Cable (P/N 75556)—used to connect the BACnet GW-3 board to an HS-NCM-
W/SF/MF boardl or NCM-W/F board and supported panel
• USB Cable (P/N 75665)—used to connect the BACnet GW-3 board to an HS-NCM-W/SF/MF
boardl
• Wire Leads to NUP Network Communications Module power cable (P/N 75583)
Network Components
• RJ45 to RJ45 standard Ethernet network cable—customer’s internet or intranet connection to
BACnet GW-3
• Workstation v3.11 or above (sold separately)
• NFN network—version 5.0 or above (sold separately)
• High Speed Network Communications Module: HS-NCM-W/SF/MF board—used to facilitate
network communication between the BACnet GW-3 and a High Speed NFN network (sold
separately) OR
• Network Communications Module: NCM-W/F board—used to facilitate network
communication between the BACnet GW-3 and an NFN network (sold separately).

NOTE: No HS-NCM-W/SF/MF board or NCM-W/F board is required when the BACnet GW-3
connects directly to a supported NOTIFIER® panel or annunciator when it is a standalone panel
or annunciator. Refer to “Panel Communication Connection Table” on page 47 for a list of
supported panels.

Cabinet and Hardware (sold separately)

• CAB-3/CAB-4 series cabinet
• CHS-4L chassis
Customer Supplied Equipment
• A computer to run the BACNet Gateway Configuration Tool and configure the BACnet GW-3.
Contact Technical Support for software version compatibility.

BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09 15

BACnet GW-3 Embedded Installation BACnet GW-3 Installation Overview

2.2 BACnet GW-3 Installation Overview

CAUTION: Multiple BACnet GW-3 Installations
! BACnet GW-3s must be installed and configured one at a time because all BACnet GW-3s use the
same predefined IP address and node number.

2.2.1 Gateway Installation Process Overview Flow Diagram

Start

“Installing a CAB3/CAB4
Cabinet” on page 18

“Installing the BACnet

GW-3 Board” on page 20

“Installing the Network

Communication Module”
on page 22

“Connecting BACnet GW-3 to an IP

Network” on page 23

To Section 3, “BACnet
GW-3 Configuration”, on
page 27

Figure 2.1 Gateway Installation Process Flow Diagram

16 BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09

BACnet GW-3 Installation Overview BACnet GW-3 Embedded Installation

2.2.2 BACnet GW-3 Board Layout

USB “A” Host (J13) USB “B” Device (J14)

Ethernet Connector
(J8)

Mounting Hole with NUP A Serial Data

Surrounding Connector (J6)
Grounding Area (5
locations)

not used (J7)

TB6:
NO
Com Not Used
NC
TB1:
-24 V Out
+24 V Out
-24 V In
+24 V In

Figure 2.2 BACnet GW-3 Board

BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09 17

BACnet GW-3 Embedded Installation Installing a CAB3/CAB4 Cabinet

2.3 Installing a CAB3/CAB4 Cabinet

Install a new CAB-3/CAB-4 series cabinet according to the requirements of the local authority
having jurisdiction or prepare an existing CAB-3/CAB-4 series cabinet that houses a supported
NOTIFIER® panel or annunciator. Refer to Appendix B, “BACnet GW-3 Compatible Node
Types”, on page 47 for list of supported panels and annunciators.

NOTE: The CAB3/CAB4 cabinet is ordered separately. For installation details, refer to the CAB-3/
CAB-4 Series Installation Document, 15330 and or the panel’s or annunciator’s documentation.

NOTE: Knockouts are provided on the unit so that the field wiring may be run in conduit if
required by the local authority having jurisdiction. All field wiring connections are intended to be
made at the installation wiring terminals provided as part of the unit.

CAB-3/CAB-4 Series Cabinets

Product Installation Document

PN 15330:I 10/23/07 07-695

1 General
All cabinets are fabricated from 16 gauge steel. The cabinet consists of two basic components: a backbox and a locking
door.
The key-locked door is provided with a pin-type hinge, two keys, and the necessary hardware to mount the door to the
backbox. The backbox has been engineered to provide ease-of-entry for the installer. Knockouts are positioned at
numerous points to let the installer bring conduit into the enclosure easily. Doors can be mounted on the left or right-hand
side. The same hinge works in both configurations, so that this choice can be made in the field. The door opens 180°.
Cabinets are available in five sizes: A through D, and AA. The outside dimensions are noted on each enclosure diagram.
“A” size accommodates one chassis, a power supply, and two 26 AH batteries; “D” size accommodates four chassis, a
power supply, and two 26 AH batteries; “AA” size holds one chassis with no compartment for batteries. A trim ring
option is available for semi-flush mounting. The CAB-3/CAB-4 Series is compatible with multiple chassis including the
CHS-M2, CHS2-M2, CHS-M3, CHS-4, CHS-4L, CHS-4N, CHS-BH, CHS-PS, CA-1, and CA-2. Note: CAB-4 series
backboxes and doors are sold separately.

2 Before You Begin

The option of mounting doors in either a left/right hand configuration
will aid in installation and service when two control panels are
CAB door [Link]

mounted in a confined area or side by side (as shown). In this manner

CAB door [Link]

the doors can be opened “barn door” style, permitting an open work
space. Note that in this type of installation it is necessary to leave
enough space between cabinets to insert a key into the locks on the
door frames.
IMPORTANT: Attach the two hinges and two alignment tabs to the
backbox before any equipment is installed. With chassis installed,
space is very limited.
Display Interface Assembly Note: When the door is left-hand
mounted, the Display Interface Assembly (DIA) dress panel cannot be
opened when the door is at less than a 120° angle to the cabinet. If you are using the left-hand mounting option, be sure
that the door can open at least 120°. This is especially important if the cabinet is to be mounted in a closed area, such as a
closet or utility room.

3 Door Assembly Instructions

Hinges can be either left or right hand mounted. The illustrations and text depict a left hand mounted example. For a right
hand mounting, simply substitute right for left in the instructions.
1. Insert door hinges (A) into the top and bottom slots of the side to be hinged (in this case the LEFT side). Secure the
hinges to the studs in the backbox with the #8 hex nuts provided. Note that the small hole on the outer tab faces
outward.
2. Thread stud (B) into the BOTTOM hinge first. Thread from the bottom up. Place the grounding “star” washer on the
stud. Place the door's lower corner onto this stud. Placing the door on the lower stud first provides a place for the door
to rest while you complete the assembly.
3. Align the door on the backbox, so that the door sits directly under the top hinge. Thread remaining stud (B) into the
TOP hinge and through the hole in the top of the door. Your door should now swing freely.

Figure 2.3 CAB-3/CAB-4 Series Installation Document, 15330

18 BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09

Installing a CHS-4L Chassis BACnet GW-3 Embedded Installation

2.4 Installing a CHS-4L Chassis

Figure 2.4 Installing a Chassis

BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09 19

BACnet GW-3 Embedded Installation Installing the BACnet GW-3 Board

2.5 Installing the BACnet GW-3 Board

Install BACnet GW-3 board onto the mounting studs on the CHS-4L chassis, making sure to use
only the mounting holes bordered by grounding area.

Grounding area

Figure 2.5 Install BACnet GW-3 Board onto Chassis

NOTE: There must be enough clearance on the right side of the printed circuit board to allow an
Ethernet cable to be connected to the Ethernet port.

2.5.1 BACnet GW-3 Power Supply Connection

The BACnet GW-3 requires +24VDC @450mA nominal and supervised battery backup in
accordance with local code requirements. Outside Canada, the BACnet GW-3 can be powered by
any regulated, UL 1481 listed, power limited, battery backed, +24 VDC power supply. For
Canadian installation, The BACnet GW-3 must be powered by a ULC listed Fire Alarm Control
Unit or a ULC listed power supply for fire application. Conform to UL or ULC standards as
applicable in your area.

Table 2.1 Power Supply Specifications

NOMINAL

Input Voltage +24VDC

Input Current @ +24VDC 450 mA without NCM or HS-NCM

20 BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09

Installing the BACnet GW-3 Board BACnet GW-3 Embedded Installation

TB1
24 V IN

Figure 2.6 BACnet GW-3 Power Connection

NOTE: All wiring from the power supply is power limited, and a separation of at least ¼” (6.35
mm) must be maintained between power limited and non-power limited wiring.

CAUTION: Power Sources

! Different sources of power are used in conjunction with the BACnet GW-3 product. Disconnect all
sources of power before servicing. This device and associated equipment may be damaged by
removing and/or inserting cards, modules or interconnecting cables while this unit is powered. This
damage may adversely affect the operation of this unit, but its effect may not be readily apparent.

For specific information about power configurations involving fire alarm control panels and
network communications modules, refer to Embedded Gateway Power Connections, PN 53600.

2.5.2 Wiring Restrictions

NOTE: All wiring connections are supervised and power limited.

NOTE: USB and NUP wiring connections to the HS-NCM must be located within 20 feet and
encased in conduit within the same room.

NOTE: In Canada, if the gateway is installed in a separate cabinet, the cabinet must be
connected to the Fire Alarm Control Panel (FACP) with a close nipple fitting.

RS232 (NUP)
• Line Impedance 5k ohm
• Max Distance 50 feet
Ethernet
• Line Impedance 100 ohm
• Max Distance 100 meters

BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09 21

BACnet GW-3 Embedded Installation Installing the BACnet GW-3 Board

USB
• Line Impedance 90 ohm ±15%
• Max Distance 40 meters

2.5.3 Installing the Network Communication Module

Install the type of network communication module you will use (whether high speed or not, wire or
fibre) onto the chassis in the new CAB3/CAB4 cabinet or an existing panel’s or annunciator’s
cabinet.

Table 2.2 Network Communication Module Details

HIGH SPEED NFN NETWORKS—USE HS-NCM ONLY NFN NETWORKS—USE NCM ONLY

Use the High Speed Network Control Module circuit board Use the Control Module circuit board configuration that fits
configuration that fits your installation needs. your installation needs.
• HS-NCM-W with twisted pair wire • NCM-W with twisted pair wire
• HS-NCM-SF with single mode fiber-optic cable • NCM-F with fiber-optic cable
• HS-NCM-MF with multimode fiber-optic cable

12 Clintonville Road
Northford, CT 06472-1610 USA 12 Clintonville Road
203-484-7161 • FAX 203-484-7118 Northford, CT 06472-1653 USA
[Link] 203-484-7161 • FAX 203-484-7118
HS-NCM-W, HS-NCM-MF, HS-NCM-SF, [Link]
HS-NCM-WMF, HS-NCM-WSF, HS-NCM-MFSF Network Communications Module NCM-W/F
High Speed Network Communications Module Product Installation Document
PN 54014:A 01/23/08 07-XXX Product Installation Document
PN 51533:C 12/28/2006 06-069
1 Product Overview
The High-Speed Network Communications Module (HS-NCM) provides a means for connecting specific Notifier fire 1 UL 864 Compliance
alarm control products to High-Speed NOTI•FIRE•NET™. There are six types of HS-NCMs available: HS-NCM-W for
connecting nodes with twisted-pair wire; HS-NCM-MF and HS-NCM-SF are used for connecting nodes with fiber-optic 1.1 Products Subject to AHJ Approval
cable; HS-NCM-WMF and HS-NCM-WSF are used for connecting nodes with fiber-optic cables to nodes with twisted-
pair wire; HS-NCM-MFSF for connecting nodes with multi-mode fiber cable to nodes with single-mode fiber cable. The This product has been certified to comply with the requirements in the Standard for Control Units and Accessories for Fire
following UL 9th Edition equipment may be used with the HS-NCM: Alarm Systems, UL 864 9th Edition.

• NFS2-3030 The following products have not received UL 864 9th Edition certification and may only be used in retrofit applications.
• NFS2-640
Operation of the NCM-W, NCM-F with products not tested for UL 864 9th Edition has not been evaluated and may not
comply with NFPA 72 and/or the latest edition of UL 864. These applications will require the approval of the local
• NFS-320
Authority Having Jurisdiction (AHJ).
• NCA-2
• AM2020/AFP1010
• DVC
• MIB
One HS-NCM can provide network communication for up to two nodes (including fire alarm control panels and network
annunciators). • NAM-232

The HS-NCM can also be configured as a repeater. In this configuration, the HS-NCM can boost data signals between
network nodes to extend communication distances or to pass data transmissions between two differently configured 2 Product Overview
network segments when wire and fiber co-exist on a network. For limitations and network wiring information for the HS-
The Network Communications Module (NCM) provides a means for connecting specific Notifier fire alarm control
NCM in repeater mode, refer to the High-Speed Noti•Fire•Net Manual. When using the HS-NCM as a repeater, the node
address for the HS-NCM must be set to zero (default). The node address can be changed through a fire alarm control
products to NOTI•FIRE•NET™. There are two types of NCMs available: NCM-W for connecting nodes with twisted-
panel’s network programming or through VeriFire Tools. Refer to the VeriFire™ Tools CD on-line help file. pair wire, and NCM-F for connecting nodes with fiber-optic cable.

For instructions on the additional capabilities available with the DVC, refer to the DVC Manual. In most applications, one NCM is required per NOTI•FIRE•NET™ node (including fire alarm control panels and
network annunciators) . Even though the NCM has two NUP ports, only one may be connected to a NOTI•FIRE•NET™.
• Input power requirements: 24 VDC, 0.375 amps, regulated, power-limited compatible power supply UL/ULC listed node. Except in some DVC applications, do not connect two NCMs via NUP ports (aka “NUP to NUP”).
for fire protective signalling use.
• Communications circuit requirements: Refer to the High-Speed Noti•Fire•Net Manual for segment length limitations. For instructions on the additional capabilities available with the DVC, refer to the DVC Manual.
• Input power requirements: 24 VDC , 0.11 amps, regulated, power-limited compatible power supply UL/ULC listed
2 The Network Communications Module for Wire (HS-NCM-W) for fire protective signalling use.
• Communications circuit requirements: Refer to the NOTI•FIRE•NET™ Manual (Network Version 4.0 and Higher)
Channel A Channel B
• Supports twisted-pair wire medium. Connection Connection for wiring length and threshold information.
• NFPA Style 4 (Class B) operation or NFPA Style 7 USB
Connections
(Class A) operation.
• Transformer coupling provides electrical isolation EtherNet
Ground Fault Connection
between nodes. Detection
• Pluggable terminal wiring with strain relief. Switches
S1=CH. A
• Pluggable service connector (feeds signal directly S2=CH. B NUP
Ports
through) in the event that power must be removed from
a node (HS-NBB).
• Data is regenerated at each node.
• Two network ports to allow simultaneous connection to
[Link]

fire alarm control panel and to programming computer.

• Enables software and database upload/download over
High-Speed Noti•Fire•Net.

Figure 1 HS-NCM-W

Figure 2.7 HS-NCM Installation Document Figure 2.8 NCM Installation Document
PN 54014 PN 51533

BE SURE TO INSTALL THE CORRECT SPEED NETWORK CONTROL MODULE, BASED ON WHETHER YOU
HAVE AN NFN NETWORK OR A HIGH SPEED NFN NETWORK.

22 BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09

Connecting BACnet GW-3 to an IP Network BACnet GW-3 Embedded Installation

2.6 Connecting BACnet GW-3 to an IP Network

This allows the BACnet GW-3 to communicate through your IP network (Internet or Intranet)
Step 1. Plug the PNET-1 surge suppressor into the BACnet GW-3 board Ethernet connector.
Step 2. Plug the RJ45 cable into the PNET-1.
Step 3. Plug the RJ45 cable into your IP network.

PNET-1 To Internet or Intranet

Ethernet
Customer Supplied Cable
Connector (J8)

Figure 2.9 IP Cable Connection

NOTE: The Ethernet wire must be connected through the PNET-1 surge suppressor.

NOTE: The Ethernet port is power limited.

2.7 Connecting BACnet GW-3 to an NFN Network or High

Speed NFN Network
The BACnet GW-3 should not be connected to the NFN network until after it has been properly
configured. For more information, please refer to Section 3, “BACnet GW-3 Configuration and
Operation”, on page 25.
Once the BACnet GW-3 has been configured, refer to Section 3.2, “Connect the BACnet GW-3 to
the NFN Network or FACP” on page 33 for more information.

BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09 23

BACnet GW-3 Embedded Installation Connecting BACnet GW-3 to an NFN Network or High Speed NFN Network

24 BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09

 Section 3 BACnet GW-3 Configuration and Operation

3.1 BACnet GW-3 Configuration

CAUTION:
! Different sources of power are used in conjunction with this product. Disconnect all sources of power
before servicing. This device and associated equipment may be damaged by removing and/or inserting
cards, modules or interconnecting cables while this unit is powered. This damage may adversely affect
the operation of this unit, but its effect may not be readily apparent.

3.1.1 BACnet GW-3 Configuration Overview

Perform the gateway configuration in this order:
• “BACNet Gateway Configuration Tool Installation” on page 25
• “Connect the Configuration Computer to the BACnet GW-3” on page 26
• “Prepare the Configuration Computer to Communicate with BACnet GW-3” on page 26
• “Log into the BACnet GW-3 for Configuration” on page 27
• “Configure the BACnet GW-3” on page 28
• “Connect the BACnet GW-3 to the NFN Network or FACP” on page 33

3.1.2 BACNet Gateway Configuration Tool Installation

The BACNet Gateway Configuration Tool CD-ROM is provided when the gateway is ordered.
Use these steps as guideline to install the application onto the computer that has Windows 2000 or
XP installed.
Step 1. Insert the CD-ROM into the CD-ROM drive on the computer that will be connected to the
gateway so the gateway can be configured.
Step 2. From Windows Explorer or the Run command, select and start the [Link] file that is
located in the CD-ROM’s root directory. The installation program starts.

Step 3. Follow the displayed instructions to install the BACNet Gateway Configuration Tool.

BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09 25

BACnet GW-3 Configuration and Operation BACnet GW-3 Configuration

3.1.3 Connect the Configuration Computer to the BACnet GW-3

If your configuration computer is on the same IP network you connected the BACnet GW-3 to in
the section, Section 2.6, “Connecting BACnet GW-3 to an IP Network” on page 23, then your
configuration computer is already connected to the BACnet GW-3. Proceed to Section 3.1.4,
“Prepare the Configuration Computer to Communicate with BACnet GW-3” on page 26.
Otherwise, refer to Appendix C, “BACnet GW-3 Local Configuration”, on page 49.

3.1.4 Prepare the Configuration Computer to Communicate with

BACnet GW-3
Configure your configuration computer to communicate with the default BACnet GW-3 IP address
of [Link].:
Step 1. From the Windows taskbar, click Start Ö Connect To Ö Show All Connections.
Step 2. Right-click your LAN connection, and then click Properties in the menu that appears.

Step 3. Select Internet Protocol (TCP/IP), and then click Properties.

26 BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09

BACnet GW-3 Configuration BACnet GW-3 Configuration and Operation

Step 4. Record your current Internet Protocol (TCP/IP) property settings so you can restore them
later.
Step 5. Click Use the following IP address, and then type 192.168.1.X into the IP address field.

NOTE: X can be any number between 0 and 255 except for 2 (since the BACnet GW-3 default IP
address is [Link]).

Step 6. Click OK, and then close all remaining open windows.

3.1.5 Log into the BACnet GW-3 for Configuration

NOTE: The BACNet Gateway Configuration Tool must run at a resolution of 1024 X 768 or
greater.

Step 1. Launch the BACNet Gateway Configuration Tool by clicking Start Ö All Programs Ö
BACnet Gateway Config Tool from the Windows taskbar.
Step 2. Click the Address field, and then click the default gateway IP address [Link] in the
menu that drops down.

Step 3. Click File Ö Login....

BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09 27

BACnet GW-3 Configuration and Operation BACnet GW-3 Configuration

Step 4. Type the default password, 00000000, and then click OK.

3.1.6 Configure the BACnet GW-3

Set Up the SNTP Server
Synchronizing with an SNTP server allows the BACnet GW-3 to keep accurate time.

NOTE: By default, the BACnet GW-3 synchronizes its internal clock with the NFN network time,
or with the Fire Alarm Control Panel in the case of a direct connection. Configuring the SNTP
server is only necessary if you want the gateway to synchronize with another server, such as an
ONYXWorks® Workstation or an SNTP time server.

Step 1. In the left pane of the BACNet Gateway Configuration Tool under the Gateway heading,
click SNTP Configuration.
Step 2. Click the SNTP Server Address field under the Value heading, and then type the address
of the SNTP server.

Configure Time Zone Settings

Step 1. In the left pane of the BACNet Gateway Configuration Tool under the Gateway heading,
click Time Zone Configuration.
Step 2. Use the fields under the Value heading to enter your local Greenwich Mean Time offset
value as well as the appropriate information about the observance of Daylight Savings
Time.

28 BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09

BACnet GW-3 Configuration BACnet GW-3 Configuration and Operation

Configure IP Settings
Step 1. In the left pane of the BACNet Gateway Configuration Tool under the Gateway heading,
click IP Configuration.
Step 2. Click the fields under the Value heading, and type the IP, Subnet Mask, and Gateway
(router) addresses this BACnet GW-3 will use on your network.
Step 3. Click Apply to activate these settings.

The BACnet GW-3 reboots automatically.

Restore Your Standard Internet Protocol (TCP/IP) Settings
Step 1. From the Windows taskbar, click Start Ö Connect To Ö Show All Connections.
Step 2. Right-click your LAN connection, and then click Properties in the menu that appears.

BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09 29

BACnet GW-3 Configuration and Operation BACnet GW-3 Configuration

Step 3. Select Internet Protocol (TCP/IP), and then click Properties.

Step 4. Enter the settings you recorded earlier into the Internet Protocol (TCP/IP) Properties
dialogue, and then click OK to return your configuration computer to your IP network.
Finalize the BACnet GW-3 Configuration
„ Log into the BACnet GW-3
Step 1. Click View Ö Refresh Gateway List to refresh the gateway address list.

Step 2. Click the Address field, and then, from the menu that drops down, click the IP address
you assigned this BACnet GW-3.

Step 3. Click File Ö Login....

Step 4. Type the default password, 00000000, and then click OK.

30 BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09

BACnet GW-3 Configuration BACnet GW-3 Configuration and Operation

The BACNet Gateway Configuration Tool now displays the remaining configurable
settings for the BACnet GW-3. Click the fields under the Value heading to enter
appropriate values, following the guidelines in the following steps.

„ Gateway Properties
• We recommend you select the Life Safety Notification Type if your system supports it.
Otherwise, virtually all clients support Multi State notification.

• Set the NCM address to a nonzero number.

• If you are adding the BACnet GW-3 to a network that already includes another gateway or
gateways, assign the Network Number based on the highest Network Number used by any
gateway already on the network. The Network Number for the new BACnet GW-3 must be
greater than the highest Network Number by one thousand. For example, if the network
already includes a gateway with a Network Number of 1001, then the lowest Network Number
which can be assigned to the new BACnet GW-3 is 2001.

„ BBMD Configuration
• If the BACnet GW-3 and the Building Management System (BMS) are connected to the IP
network across different subnets, they must be connected through a BACnet Broadcast
Management Device (BBMD). When using a BBMD, set the Foreign Device value to True
and enter values for IP Address, Port and Register Time.

BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09 31

BACnet GW-3 Configuration and Operation BACnet GW-3 Configuration

„ Multiple Gateways
• NFN networks with more than 15 nodes must be monitored using the Multiple Gateway
option.
• When using this Multiple Gateway option, set the Multiple Gateway value to True, and enter a
value for each network node to be monitored by this BACnet GW-3.

• You may enter up to 14 nodes for FACPs to be monitored, since the BACnet GW-3 can support
15 nodes including itself.

„ Apply Settings
Step 5. Once all BACnet GW-3 settings have been properly configured, click Apply at the bottom
of the Value pane to apply the settings and reboot the gateway.

NOTE: If you are changing settings on a BACnet GW-3 previously configured with monitored
nodes, this screen button will be labeled Apply And Delete Objects.

32 BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09

Connect the BACnet GW-3 to the NFN Network or FACP BACnet GW-3 Configuration and Operation

3.1.7 Viewing BACnet GW-3 Activity with the BACNet Gateway

Configuration Tool
The Gateway Activity window displays information about panels, network objects and NUP events
processed by the BACnet GW-3. This utility tracks up to the 4,000 most recent records. Store this
information permanently by clicking Save.

NOTE: The NFN network must be stable with very few events in order for the discovery process
to discover all objects upon initial configuration. After initial configuration, the BACnet GW-3
updates the network daily at its specified Network Update Time (the default time is [Link]).

It is helpful to launch the Gateway Activity window before connecting the BACnet GW-3 to an
NFN network or directly to a Fire Alarm Control Panel, so you can monitor the messages the
BACnet GW-3 generates in its initial Auto Discovery and Property Search routines. To open the
Gateway Activity window:
Step 1. Log into the BACnet GW-3 (refer to “Log into the BACnet GW-3” on page 30).
Step 2. Click View Ö Gateway Activity.

The Gateway Activity window opens. Network traffic will affect the time required to populate the
Gateway Activity window.

3.2 Connect the BACnet GW-3 to the NFN Network or FACP

The BACnet client workstation front end must conform to BACnet Standard Annex J for
IP and support Device Objects, Binary Output Objects, and Multi-state Input or Life
Safety Points/Zones. It is also required to write to Notification Objects and receive
confirmed/unconfirmed event notification messages. For details, refer to Appendix A,
“PIC Statement”, on page 41.

BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09 33

BACnet GW-3 Configuration and Operation Connect the BACnet GW-3 to the NFN Network or FACP

„ Find Your Fire System Connection Option

Once the BACnet GW-3 is connected to the IP network, connect it to either a fire alarm control
panel or an appropriate network control module. Refer to Table 3.1, "BACnet GW-3 to Fire System
Connection Options" for details.

NOTE: Make only one of these connections.

Table 3.1 BACnet GW-3 to Fire System Connection Options

When Connecting... Refer to

...to a high speed NFN network consisting exclusively of Section 3.2.1, “Connecting BACnet GW-3 to a High
High Speed compatible panels Speed NFN Network Control Module” on page 35

...to an NFN network Section 3.2.2, “Connecting BACnet GW-3 to an NFN

Network Control Module” on page 37

directly to a fire alarm control panel to be accessed Section 3.2.3, “Connecting BACnet GW-3 Directly to a
through the BACnet GW-3 Fire Alarm Control Panel” on page 38

34 BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09

Connect the BACnet GW-3 to the NFN Network or FACP BACnet GW-3 Configuration and Operation

3.2.1 Connecting BACnet GW-3 to a High Speed NFN Network

Control Module
• Use a HS-NCM-W for a twisted pair wire connection.
• Use a HS-NCM-SF for a single mode fiber-optic cable connection.
• Use a HS-NCM-MF for a multimode fiber-optic cable connection.
Connecting the BACnet GW-3 to an HS-NCM-W/SF/MF allows the gateway to communicate with
devices on a high speed NFN network. Connect an BACnet Gateway-3 to a High Speed Network
Control Moduleusing either of these methods:

„ USB to USB Cable Connection

Connecting the BACnet GW-3 to an HS-NCM-W, HS-NCM-SF or HS-NCM-MF allows the
gateway to communicate with devices on a high speed NFN network. Connect the cable between
the USB “A” port on a BACnet GW-3 board and the USB “B” port on an HS-NCM-W, HS-NCM-
SF or HS-NCM-MF. Or, connect the cable between the USB “B” port on a BACnet GW-3 board
and the USB “A” port on an HS-NCM-W, HS-NCM-SF or HS-NCM-MF.

USB cable

BACnet GW-3
HS-NCM-W/MF/SF

Figure 3.1 USB Connection

BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09 35

BACnet GW-3 Configuration and Operation Connect the BACnet GW-3 to the NFN Network or FACP

„ NUP to NUP Cable Connection

A NUP to NUP cable is used to connect between the gateway and the NFN network. Connect the
cable between to the BACnet GW-3 circuit board NUP “A” connector and an HS-NCM-W/SF/MF
board NUP “A” connector.

NUP to NUP cable

NUP A (J6)
USE NUP A ONLY
Connect to an HS-NCM-W/SF/MF
using NUP “A” only

Figure 3.2 NUP to NUP Connection

36 BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09

Connect the BACnet GW-3 to the NFN Network or FACP BACnet GW-3 Configuration and Operation

3.2.2 Connecting BACnet GW-3 to an NFN Network Control

Module
• Use an NCM-W for a twisted pair wire connection.
• Use an NCM-F for a fiber-optic cable connection.
Connecting the BACnet GW-3 to an NCM-W or NCM-F allows the gateway to communicate with
devices on an NFN network.

„ NUP to NUP Cable Connection

Connect the cable between to the BACnet GW-3 NUP “A” connector and an NCM-W or NCM-F
NUP connector.

NUP A (J6)
Use NUP “A” only.

NUP to NUP cable

Connect to an NCM-W/F,

Figure 3.3 NUP to NUP Connection

BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09 37

BACnet GW-3 Configuration and Operation Back Up BACnet GW-3

3.2.3 Connecting BACnet GW-3 Directly to a Fire Alarm Control

Panel
The BACnet GW-3 connects to Fire Alarm Control panels over NUP. Refer to Appendix B.1,
“Direct Connect Node Type Compatibility”, on page 47 for a list of supported panels.

NUP A (J6)
Use NUP “A” only.

NUP to NUP cable

Connect to FACP

Figure 3.4 NUP to NUP Connection

3.3 Back Up BACnet GW-3

Backing up the BACnet GW-3 is important once the gateway is working properly. In some cases, if
the gateway loses power while saving files, the gateway object database may be deleted. Without a
backup file, the gateway will need to rediscover the network and the recipient list may also need to
be set up again.

CAUTION: Auto Discovery and Property Search

! To ensure the full object database is preserved, give the BACnet GW-3 time to complete its initial
Auto Discovery and Property Search procedures before backing it up. For more information, please
refer to “Viewing BACnet GW-3 Activity with the BACNet Gateway Configuration Tool” on page 33.

Step 1. Log into the BACnet GW-3 (refer to “Log into the BACnet GW-3” on page 30).
Step 2. Click Tools Ö Backup Gateway.

38 BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09

Restore BACnet GW-3 BACnet GW-3 Configuration and Operation

Step 3. Navigate to where you want to store the backup file, type a name for the file, and then
click Save.

3.4 Restore BACnet GW-3

Follow these steps to restore a previously backed up BACnet GW-3.
Step 1. Log into the BACnet GW-3 (refer to “Log into the BACnet GW-3” on page 30).
Step 2. Click Tools Ö Restore Gateway.

Step 3. Navigate to where the backup file (.bnk) was saved, click on the file name, and then click
Open.

The gateway is restored, and reboots automatically.

BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09 39

BACnet GW-3 Configuration and Operation BACnet GW-3 Operation

3.5 BACnet GW-3 Operation

3.5.1 About BACnet GW-3 Start Up
On start up, the gateway auto discovers devices (panels and annunciators.) and objects (detectors,
modules, panels circuits, zones, loops, battery, AC Power, Ground, etc....) on NFN network it is
connected to and creates BACnet objects according to your configuration.
Devices and objects are given names Below are some format examples:

An AFP1010 as node 142: .Name = 142AFP1010 (BACnet Device Object)

An NFS640 as node 234: .Name = 234_NFS640 (BACnet Device Object)

(Detector) Loop 5, Detector 83: L005D083 (BACnet Life Safety Point or Multi-state Input Object)

(Zone) Zone 134: ZONE0134 (BACnet Life Safety Zone or Multi-state Input Object)

Any Node, Loop 5, Control Module 12: L005C012 (BACnet Binary Output Object)

An AM2020 as node 120: .Name = 120_AM2020 (_ denotes spaces) (BACnet Device Object)

An NCM as node 11 connected to BACnet GW: .Name = 011_ _ _ BACGW (BACnet Device Object)

(Module) Loop 9, Module 120: L009M120 (BACnet Life Safety Point or Multi-state Input Object)

(Zone) Zone 1003: ZONE1003 (BACnet Life Safety Zone or Multi-state Input Object)

(Panel Internal Devices)--LOOP 8, LOOP10, BATTERY, ANNUN021, ACPOWER, PANEL (BACnet Life Safety Point or
Multi-state Input Object)

40 BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09

 Appendix A: PIC Statement

A.1 BACnet Protocol Implementation Conformance

Statement (Normative)
(This appendix is part of this Standard and is required for its use.)
• Applications Software Version: 3.11
• Firmware Revision: 3.11
• BACnet Protocol Revision: 1.2
Product Description:
This product presents NOTIFIER® Fire Panel and Annunciator nodes (operating as part of a NFN
network or stand-alone) and their associated objects as BACnet objects. Event notification for
Alarms, Troubles and other states are sent to registered BACnet client workstations.
BACnet Standardized Device Profile (Annex L)

BACnet Inter-operability Building Blocks Supported (Annex K)

DS-RP-B DS-RPM-B

DS-WP-B DS-WPM-B

AE-N-I-B AE-ACK-B

AE-ASUM-B AE-INFO-B

DM-DDB-B

DM-DOB-A DM-DOB-B

DM-LM-B

Segmentation Capability
• Segmented requests supported, Window Size 1024 max.
• Segmented responses supported, Window Size 1024 max.
Standard Object Types Supported - Life Safety Point/Life Safety Zone

BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09 41

PIC Statement BACnet Protocol Implementation Conformance Statement (Normative)

Present Value BACnet Enumeration BACnetLifeSafetyState NFN State

0 IssQ uiet Norm al

1 IssP reA larm P reA larm

2 IssA larm Fire A larm , S ecurity A larm (Life/P rope rty), C ritical P rocess A larm
(Life/P rope rty), M edical E m ergency
3 IssFault S ecurity Trouble, Fire Trouble, Non-Fire Trouble, Fire D evice or Zone
D isabled , Non-Fire D evice D isabled

7 IssA ctive Non-Fire A ctivation

22 IssS upervisory Supervisory (E quipm ent), S upervisory (G uard’s Tour)

Tracking Value BACnet Enumeration BACnetLifeSafetyState NFN State

0 IssQ uiet Norm al

1 IssP reA larm P reA larm

2 IssA larm Fire A larm , S ecurity A larm (Life/P rope rty), C ritical P rocess A larm
(Life/P rope rty), M edical E m ergency
3 IssFault S ecurity Trouble, Fire Trouble, Non-Fire Trouble, Fire D evice or Zone
D isabled , Non-Fire D evice D isabled
7 IssA ctive Non-Fire A ctivation

22 IssS upervisory Supervisory (E quipm ent), S upervisory (G uard’s Tour)

Event State BACnet Enumeration BACnetEventState NFN State

0 E sNorm al Norm al

1 E sFault S ecurity Trouble, Fire Trouble, Non-Fire Trouble, Fire D evice or Zone
D isabled , Non-Fire D evice D isabled
2 E sO ffNorm al A ll statuses other than norm al and fault.

Reliability BACnet Enumeration BACnetReliability NFN State

0 reNoFaultD etected A ll statuses other than trouble.

7 re_ UnreliableO ther S ecurity Trouble, Fire Trouble, Non-Fire Trouble

Mode BACnet Enumeration BACnetMode NFN State

0 Ism O ff P ow er-Up State

10 Ism E nabled S et if point has bee n disabled and subsequently enabled since startup.

11 Ism D isabled Fire D evice or Zone D isab led , Non-Fire D evice D isabled

Silence State BACnet Enumeration NFN State

0 ssUnsilenced A udibles Unsilenced

1 ssA udiblesS ilenced A udibles S ilenced

Operation BACnet Enumeration NFN State

Expected
0 NA

Maintenance BACnet Enumeration NFN State

Required
NA NA NA

Event Enable BACnet Event Transition Bit

toO ffNorm al

toFault

Direct Reading R E AL NA % A larm

Status Flags Boolean BACnet Status Flags NFN State

0,0,0,0 Norm al

1,0,0,0 InA larm Fire A larm , S ecurity A larm (Life/P rope rty), C ritical P rocess A larm
(Life/P rope rty), M edical E m ergen , P reA larm

1,1,0,0 InAlarm , Fault S ecurity Trouble, Fire Trouble, Non-Fire Trouble

1,0,0,1 InA larm , O utO fService Fire D evice or Zone D isab led , Non-Fire D evice D isabled

Out of Service Boolean NFN State

0 FALSE A ll statuses other than disable

1 TR UE Fire D evice or Zone D isab led , Non-Fire D evice D isabled

42 BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09

BACnet Protocol Implementation Conformance Statement (Normative) PIC Statement

Standard Object Types Supported - Multi-state Input Standard Object Types

BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09 43

PIC Statement BACnet Protocol Implementation Conformance Statement (Normative)

Supported - Binary Output

Present Value BACnet Enumeration BACnetLifeSafetyState NFN State
0 IssQ uiet Norm al

1 IssP reAlarm P reAlarm

2 IssAlarm Fire Alarm , Security Alarm (Life/Prope rty), C ritical Process A larm
(Life/P roperty), M edical E m ergency
3 IssFault S ecurity Trouble, Fire Trouble, Non-Fire Trouble, Fire D evice or Zone
D isabled, Non-Fire D evice D isabled
7 IssA ctive Non-Fire A ctivation

22 IssSupervisory Supervisory (E quipm ent), Supervisory (G uard’s Tour)

Tracking Value BACnet Enumeration BACnetLifeSafetyState NFN State

0 IssQ uiet Norm al

1 IssP reAlarm P reAlarm

2 IssAlarm Fire Alarm , Security Alarm (Life/Prope rty), C ritical Process A larm
(Life/P roperty), M edical E m ergency
3 IssFault S ecurity Trouble, Fire Trouble, Non-Fire Trouble, Fire D evice or Zone
D isabled, Non-Fire D evice D isabled
7 IssA ctive Non-Fire A ctivation

22 IssSupervisory Supervisory (E quipm ent), Supervisory (G uard’s Tour)

Event State BACnet Enumeration BACnetEventState NFN State

0 E sNorm al Norm al

1 EsFault S ecurity Trouble, Fire Trouble, Non-Fire Trouble, Fire D evice or Zone
D isabled, Non-Fire D evice D isabled
2 E sO ffNorm al All statuses other than norm al and fault.

Reliability BACnet Enumeration BACnetReliability NFN State

0 reNoFaultD etected All statuses other than trouble.

7 re_UnreliableO ther Security Trouble, Fire Trouble, Non-Fire Trouble

Mode BACnet Enumeration BACnetMode NFN State

0 Ism O ff Pow er-Up State

10 Ism E nabled S et if point has been disabled and subsequently enabled since startup.

11 Ism D isabled Fire D evice or Zone D isabled, Non-Fire D evice D isabled

Silence State BACnet Enumeration NFN State

0 ssUnsilenced Audibles Unsilenced

1 ssA udiblesS ilenced Audibles S ilenced

Operation BACnet Enumeration NFN State

Expected
0 NA

Maintenance BACnet Enumeration NFN State

Required
NA NA NA

Event Enable BACnet Event Transition Bit

toO ffNorm al

toFault

Direct Reading R E AL NA % Alarm

Status Flags Boolean BACnet Status Flags NFN State

0,0,0,0 Norm al

1,0,0,0 InA larm Fire Alarm , Security Alarm (Life/Prope rty), C ritical Process A larm
(Life/P rope rty), M edical E m ergen , PreA larm

1,1,0,0 InA larm , Fault S ecurity Trouble, Fire Trouble, Non-Fire Trouble

1,0,0,1 InA larm , O utO fS ervice Fire D evice or Zone D isabled, Non-Fire D evice D isabled

Out of Service Boolean NFN State

0 FA LS E All statuses other than disable

1 TR UE Fire D evice or Zone D isabled, Non-Fire D evice D isabled

44 BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09

BACnet Protocol Implementation Conformance Statement (Normative) PIC Statement

Standard Object Types Supported - Notification Class

Write Property/Add List element required for Intrinsic Reporting.

„ Data Link Layer Options

„ Device Address Binding:

Is static device binding supported? (This is currently necessary for two-way communication with
MS/TP slaves and certain other devices.)
• Select - Yes
• No

„ Networking Options:
• Select - Router, Clause 6 - List all routing configurations, e.g., ARCNET-Ethernet, Ethernet-
MS/TP, etc. BACnet to Proprietary ARCnet Fire Network
• Annex H, BACnet Tunneling Router over IP
• BACnet/IP Broadcast Management Device (BBMD)
Does the BBMD support registrations by Foreign Devices?
• Yes
• Select - No

„ Character Sets Supported:

Indicating support for multiple character sets does not imply that they can all be supported
simultaneously.

If this product is a communication gateway, describe the types of non-BACnet equipment/

network(s) that the gateway supports:
Notifier Fire and Annunciator nodes compatible with NFN network v5.0 and later operating in a
network or stand-alone configuration.

BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09 45

PIC Statement BACnet Protocol Implementation Conformance Statement (Normative)

46 BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09

 Appendix B: BACnet GW-3 Compatible Node Types
NOTE: The BACnet GW-3 requires that at least one node on the NFN network be an ONYX
series panel. BACnet GW-3 does not operate on an NFN network with no ONYX series panels.

B.1 Direct Connect Node Type Compatibility

Refer to Section 3.2.3, “Connecting BACnet GW-3 Directly to a Fire Alarm Control Panel” on
page 38.

Table B.1 Panel Communication Connection Table

Supported Panel Types

NFS-320

NFS2-640

NFS2-3030

NCM

NFS-640

NFS-3030

BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09 47

BACnet GW-3 Compatible Node Types Direct Connect Node Type Compatibility

48 BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09

 Appendix C: BACnet GW-3 Local Configuration

NOTE: This procedure is only necessary if you are configuring an BACnet GW-3 using a
Configuration computer that is not already on the same IP network as the BACnet GW-3. Refer to
“Connecting BACnet GW-3 to an IP Network” on page 23.

NOTE: A direct connection requires that a cross over Ethernet cable to be made or purchased
by the customer.

C.1 Direct Connection to the Gateway Board

Step 1. Connect the cross over cable between the configuration computer network card’s Ethernet
connector and the BACnet GW-3 board’s Ethernet connector (refer to "Cross Over Cable
Specifications").

PNET-1 To Configuration Computer

Ethernet
Customer Supplied Cable
Connector (J8)

Figure C.1 Configuration Computer Direct Connection

Step 2. You have completed the connections, proceed to “Add the IP Subnet of the BACnet GW-3
into the Configuration PC” on page 28.

„ Cross Over Cable Specifications

This cross over cable will be directly connected between the configuration computer network card
Ethernet connector and the BACnet GW-3 board Ethernet connector.

BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09 49

BACnet GW-3 Local Configuration Direct Connection to the Gateway Board

The cross over cable can be purchased or you can make one. Please use the following information
for the correct pinout requirements for each end of the cable. EIA/TIA wire color-code standard
568B is applicable.

Table C.1 Cross Over Cable (568B)

RJ45 Pin # RJ45 Pin #

Wire Color Diagram End #1 Wire Color Diagram End #2
(END 1) (END 2)

1 White/Orange 1 White/Green

2 Orange 2 Green

3 White/Green 3 White/Orange

4 Blue 4 Blue

5 White/Blue 5 White/Blue

6 Green 6 Orange

7 White/Brown 7 White/Brown

8 Brown 8 Brown

50 BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09

 Appendix D: Glossary
B
NOTIFIER® BACnet Gateway-3 An interface that
allows the NFN network to communicate with a
BACnet network.
F
FTP File Transfer Protocol, used to back up the
NOTIFIER® BACnet Gateway-3 database and
download firmware for field upgrades.
H
HS-NCM-W/SF/MF High Speed Network Control
Module, a network interface enabling the NOTIFIER®
BACnet Gateway-3 to communicate with other NFN
devices.
I
IP Address Logical address designating a node on an
IP network with the format [Link],
where NNN groups can be between 0 and 255.
NFN The network of Fire Alarm Control
[Link] - Local area network protocol.
T
Telnet An Internet protocol that allows you to
communicate directly with another computer on the
Internet by specifying the host name, port and terminal
type.

BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09 51

Glossary

52 BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09

 Index
A configuration 49
features 7
ANSI/ASHRAE 135-1995 7
Hardware Installation 20
architecture
system 11 IP cable connection 23
Required Equipment 15
ARCNET 45
gateway
configuration overview 25
B Gateway board
BACnet Configuration Tool layout 17
installation procedure 25 Gateway Installation
BACnet Gateway Overview 16
Features 7
BACnet Gateway part number 15 H
BACnet Inter-operability Building Blocks 41
BACnet Standard Annex J for IP 7 HS-NCM board 22
Bacnet Standardized Device Profile 41
Binary Output Objects 7 I
Installation
C Environmental Conditions 9
IP Address 51
Cabinet Installation 18
Character Sets Supported 45
Configuration computer L
connections 26 Life Safety Points 7
configuration computer Life Safety Zones 7
direct connection 49 Line Impedance 21

D M
Data Link Layer Options 45 Max Distance 21
device Multi-state Input 7
BACnet names 40
Device Address Binding 45
Device Compatibility 8
N
Device Objects 7 NCM board 22
Network Cable Connection 35
Network Communication Module Installation 22
E Network Interface Board 15
EIA/TIA wire color-code standard 50 NFN Network Connections 23
Ethernet Normative 41
Line Impedance 21 Notification Class 45
Max Distance 21 Notification Objects 7
Ethernet cross over cable NUP
specifications 49 Line Impedance 21
Ethernet Network Max Distance 21
about 9 NUP to NUP Cable 15
NUP to NUP Cable Connection 36, 37
F
fiber-optic cable 22 O
object
G BACnet names 40
Gateway
assembly 15

BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09 53

 Index

P
PIC STATEMENT 41
PNET-1 15
Power Connections 20

R
Related Documentation 8
RS232
Line Impedance 21
Max Distance 21

S
Segmentation Capability 41
Serial Configuration Tool
operating system 10
Standard Object Types Supported 41
Supported - Binary Output 44
System Requirements 10

T
twisted pair wire 22

U
USB
Line Impedance 22
Max Distance 22

W
Wiring
Power 20

54 BACnet Gateway-3 Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09

 Limited Warranty
Honeywell International Inc. warrants products manufactured by
it to be free from defects in materials and workmanship for
eighteen (18) months from the date of manufacture, under normal
use and service. Products are date stamped at time of
manufacture. The sole and exclusive obligation of Honeywell
International Inc. is to repair or replace, at its option, free of charge
for parts and labor, any part that is defective in materials or
workmanship under normal use and service. All returns for credit
are subject to inspection and testing at the factory before actual
determination is made to allow credit. Honeywell International
Inc. does not warrant products not manufactured by it, but assigns
to the purchaser any warranty extended by the manufacturer of
such products. This warranty is void if the product is altered or
repaired by anyone other than Honeywell International Inc. or as
expressly authorized by Honeywell International Inc. in writing, or
is serviced by anyone other than Honeywell International Inc. or
its authorized distributors. This warranty is also void if there is a
failure to maintain the products and systems in which they operate
in a proper and workable manner. In case of defect, secure a
Return Material Authorization form from our Return Authorization
Department.
This writing constitutes the only warranty made by Honeywell
International Inc., with respect to its products. Honeywell
International Inc., does not represent that its products will prevent
any loss by fire or otherwise, or that its products will in all cases
provide the protection for which they are installed or intended.
Buyer acknowledges that Honeywell International Inc., is not an
insurer and assumes no risk for loss or damages or the cost of any
inconvenience, transportation damage, misuse, abuse, accident or
similar incident.
HONEYWELL INTERNATIONAL INC. GIVES NO WARRANTY,
EXPRESS OR IMPLIED, OF MERCHANTABILITY, FITNESS FOR
ANY PARTICULAR PURPOSE, OR OTHERWISE WHICH
EXTENDS BEYOND THE DESCRIPTION ON THE FACE
HEREOF. UNDER NO CIRCUMSTANCES SHALL HONEYWELL
INTERNATIONAL INC. BE LIABLE FOR ANY LOSS OF OR
DAMAGE TO PROPERTY, DIRECT, INCIDENTAL OR
CONSEQUENTIAL, ARISING OUT OF THE USE OF, OR
INABILITY TO USE HONEYWELL INTERNATIONAL INC.’S
PRODUCTS. FURTHERMORE, HONEYWELL INTERNATIONAL
INC. SHALL NOT BE LIABLE FOR ANY PERSONAL INJURY OR
DEATH WHICH MAY ARISE IN THE COURSE OF, OR AS A
RESULT OF, PERSONAL, COMMERCIAL OR INDUSTRIAL USE
OF ITS PRODUCTS.

NOTIFIER® BACnet Gateway-3 - Installation and Operation Manual - P/N: 53372:Rev: A 5/6/09 55
 World Headquarters
12 Clintonville Road
Northford, CT 06472-1610 USA
203-484-7161
fax 203-484-7118

[Link]