AISSCE 2025
CHEMISTRY INVESTIGATORY PROJECT
ON
(TOPIC)
CONTENTS
1. CERTIFICATE
2.ACKNOWLEDGEMENT
3.INTRODUCTION
4. Internal Resistance
5.EXPERIMENTAL WORK
Objective
Apparatus Required
Theory
Circuit Diagram
Procedure
Results and Inferences
Precautions
Source of Error
6.BIBLIOGRAPHY
CERTIFICATE PAGE
This is to certify that Mohammed
Saim Rahman of class: - XII 'C' has
satisfactorily completed his Physics
investigatory project as prescribed by
the CBSE during the academic year
2024-2025.
Teacher’s signature:-
..............................
ACKNOWLEDGEMENT
I would like to sincerely and profusely
thank my Physics teacher Ms. Ahana Roy
and our lab attendant for their able
guidance and support in completing my
project.
I would also like to extend my gratitude to
the principal Mrs. Paromita Guha Ray for
providing me all the facilities that was
required.
SIGNATURE OF STUDENT:-
………………………………
INTRODUCTION
There is a great need of batteries in our
daily use electrical appliances and the use
is increasing every day. Thus, the batteries
need to be made more powerful so that
their potential can be increased greatly.
Thus, this project report is based on the
practical analysis for the factors affecting
the internal resistance of a cell.
When the internal resistance of the cell is
decreased we can increased the potential
difference across it, and hence make it
more reliable.
INTERNAL RESISTANCE
Internal resistance is defined as the resistance
offered by the electrolyte of the cell to the
flow of ions.
Its S.I unit is ohm (Ω).
For a cell of e.m.f. (E) and internal resistance
(r), connected to an external resistance (R)
such that (I) is the current flowing through the
circuit.
E = V + Ir
INTERNAL RESISTANCE, r = (E – V)/I
PRACTICAL ANALYSIS
OBJECTIVE:-
To study the various factors on which the internal resistance
of the cell depends.
APPARATUS REQUIRED:-
A potentiometer, a battery(or battery eliminator) , two one
way keys , a rheostat , a galvanometer , a resistance box , an
ammeter , a cell (Leclanche cell) , a jockey , a setsquare ,
connecting wires and sand papers.
THEORY:-
The internal resistance of a cell is the resistance offered by
its electrolyte to the flow of ions. The internal resistance of a
cell
Is directly proportional to the distance between the
electrodes.
Is inversely proportional to facing surface area of the
electrode in electrolyte.
Decrease with increase in temperature of electrolyte.
Is inversely proportional to the concentration of
electrolyte.
THE INTERNAL ESISTANCE OF A CELL IS GIVEN BY: -
R = (E – V)/I
CIRCUIT DIAGRAM:-
PROCEDURE:-
1. Clean the ends of the connecting wires with sand paper
make tight connection according to the circuit diagram.
2. Tighten the plugs of the resistance box.
3. Check the e.m.f. of the battery and of the cell and make
sure that e.m.f. of the battery is more than that of the
cell , otherwise null or balance point will not be
obtained
4. Keep both the electrodes at a distance of 16cm.
5. Take maximum current from the battery, making
rheostat resistance small.
6. Without inserting a plug in key K2, adjust the rheostat
so that a null point is obtained on the last wire of the
potentiometer.
7. Determine the position of the null point accurately using
a setsquare and measure the balancing length (l1),
between the null point and the end P.
8. Next introduce plugs in both keys K1 and K2.At the same
time, take out a small resistance (1 – 5 W) from the
shunt resistance box connected I parallel with the cell.
9. Slide the jockey along a potentiometer wire and obtain
the null point.
10. Measure the balancing length (l2) from end P.
Record these observations.
11. Now keep the electrodes 12cm apart.
12. Then remove the plugs of keys K1 andK2.Wait for
some time and repeat steps 7 to 10.
13. Next, keep the electrodes 9cm apart to
obtain another set of observations.
14. Keeping all other factor constant, increase the area
of the electrodes in the electrolyte by dipping them into
the electrolyte at different depths for each
observations.
15. Obtain three such observations by repeating steps
7 to 10.Record these readings.
16. Keeping all other factors constant, decrease the
concentration of electrolyte by adding distilled water for
different observations.
17. Obtain three such observations by repeating steps
7 to 10.Record these readings.
OBSERVATIONS:-
S.NO AMMETER POSITION OF NULL POINT SHUNT INTERNAL
RESISTANCE
READING (CM) RESISTANCE
WITH R WITHOUT R R (Ω) r (Ω)
(A)
(l1) (l2)
1. 0.3 660.5 35.5 1 0.94
2 1.77
2. 0.3 660.5 77.2
660.5 108.3 3 2.51
3. 0.3
TABLE FOR EFFECT OF SEPARATION BETWEEN ELECTRODES.
S.No Separation Balancing Balancing INTERNAL
RESISTANCE
Between Point Point r/d
Electrodes l1(cm) l2(cm) r(Ω)
d (cm)
1. 1.2 326.6 276.9 0.456 0.38
2. 2.5 320.7 219.1 0.95 0.38
3. 3.7 660.5 350.9 1.406 0.38
TABLE FOR EFFECT OF TEMPERATURE.
S.No Temperature l1 l2 Resistance INTERNAL Tr
T(ºC) R(Ω) RESISTANCE
(cm) (cm) (ΩK)
r(Ω)
1. 1.2 326.6 276.9 0.456 0.38 301.44
2. 2.5 320.7 219.1 0.95 0.38 291.96
3. 3.7 660.5 350.9 1.046 0.38 283.87
RESULTS AND INFERENCES:-
The electromotive force of the cell is constant and is equal
to E = 0.98 volt.
The internal resistance of a cell is directly proportional to
the separation between the electrodes.
The internal resistance of a cell is inversely proportional to
the area of the electrodes dipped in electrolyte.
The internal resistance of a cell is inversely proportional to
the temperature of electrolytes
The internal resistance of a cell is inversely proportional to
the concentration of the electrolyte.
PRECAUTIONS:-
The connections should be neat, clean and tight.
The plugs should be introduced in the keys only when
the observations are to be taken.
The positive polls of the battery E and cells E 1 and E2
should all be connected to the terminal at the zeros of
the wires.
The jockey key should not be rubbed along the wire. It
should touch the wire gently.
The ammeter reading should remain constant for a
particular set of observation. If necessary, adjust the
rheostat for this purpose.
SOURCES OF ERROR:-
The auxiliary battery may not be fully charged.
The potentiometer wire may not be of uniform cross
section and material density throughout its length.
End resistance may not be zero.
BIBLIOGRAPHY
1. WEBSITE:_
www.google.com
www.yahoo.com
www.wikipedia.org
www.bing.com
www.quora.com
2. BOOKS:_
Comprehensive Practical
manual
NCERT CLASS XII
