Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

ELECTRICAL NETWORK THEORY

DEPARTMENT OF ELECTRICAL ENGINEERING

Prepared By: Checked By: Approved By:

Engr. Yousaf Hameed Engr. M.Nasim Khan Dr.Noman Jafri

Lecturer (Lab) Electrical, Senior Lab Engineer Electrical, Dean,
FUUAST-Islamabad FUUAST-Islamabad FUUAST-Islamabad

Electrical Network Theory 1

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

Name: ____________________________________________

Registration No: ____________________________________

Roll No: ___________________________________________

Semester: _________________________________________

Batch: ____________________________________________

Electrical Network Theory 2

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

C
COON
NTTE
ENNT
TSS

Exp No List of Experiments

1 TO VERIFY SUPERPOSITION PRINCIPLE IN DC CIRCUITS

2 TO VERIFY THEVENIN THEOREM BY FINDING ITS THEVENIN’S EQUIVALENT CIRCUIT

3
TO VERIFY MAXIMUM POWER TRANSFER THEOREM

4
TO OBSERVE VARIATION IN IMPEDANCE AND CURRENT OF AN RC SERIES NETWORK IN AC CIRCUIT

5
TO OBSERVE VARIATION IN IMPEDANCE AND CURRENT OF AN RL SERIES NETWORK IN AC CIRCUIT

6
TO OBSERVED AND DETERMINE THE RESONANT FREQUENCY OF A RESONANT CIRCUIT

7 DC RC CIRCUIT AND TRANSIENT PHENOMENA

8
THE PULSE RESPONSE OF A SERIES RC NETWORK

9
THE PULSE RESPONSE OF A SERIES RL NETWORK

TO SHOW THE FREQUENCY RESPONSE OF A SERIES RLC NETWORK AND SHOW THAT THE RESONANT
10
FREQUENCY OF A SERIES RLC CIRCUIT IS GIVEN BY 1/2T LC

11 A. SINUSOIDAL RESPONSE OF RL CIRCUIT

B. SINUSOIDAL RESPONSE OF RC CIRCUIT
FREQUENCY CHARACTERISTICS OF A SIMPLE LOW PASS RL FILTER CIRCUIT AND TO UNDERSTAND THE
12
BEHAVIOR OF THE CIRCUIT WITH RELATION TO THE POLE ZERO LOCATION

13 FREQUENCY CHARACTERISTICS OF A SIMPLE HIGH PASS RL FILTER CIRCUIT AND TO UNDERSTAND THE
BEHAVIOR OF THE CIRCUIT WITH RELATION TO THE POLE ZERO LOCATION.
14
TO PLOT THE MAGNITUDE AND PHASE RESPONSE OF A SERIES RESONANAT BAND FILTER

15
TO PLOT THE MAGNITUDE AND PHASE RESPONSE OF A SERIES RESONANT BAND-STOP FILTER.

16
TO VERIFY THE PRINCIPLE OF SUPER POSITION USING AC AND DC SOURCES

Electrical Network Theory 3

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

EXPERIMENT NO: 01

SUPERPOSITION THEOREM
OBJECTIVE:

To Verify Superposition Principle in DC Circuits

REQUIRED:

1- DMM
2- 2 DC Power Supplies,
3- Resistances (1k Ω, 2k Ω, 430k Ω)
THEORY:

The superposition principle states that:

“The current through or voltage across, any resistive branch of a

multisource network is the algebraic sum of the contribution due to each
source acting independently.”

When the effect of one source is considered, the others are replaced by their internal
resistances. This principle permits one to analyze circuits without restoring to simultaneous
equations.

Superposition is effective only for linear circuit relationship. Non-linear effects, such as power,
which varies as the square of the current or voltage, cannot be analyzed using this principle.

FIGURE:

Fig-1

Electrical Network Theory 4

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

Fig – 2

Fig – 3

PROCEDURE:

1. Construct the Network of Fig-1, where R1 = 1 k Ω, R2 = 430 Ω, R3 = 2 k Ω. Verify the resistances

using DMM.
2. Using superposition and measured resistance values, calculate the currents indicated in
observation Table (a), for the network of Fig-1. Next to each magnitude include a small arrow to
indicate the current direction for each source and for the complete network.
3. Energize the network of Fig-1 and measure the voltages indicated in observation table b,
calculate current in Table (b) using Ohm’s Law. Indicate the polarity of the voltages and direction
of currents on Fig-1.
4. Construct the network of Fig -2. Note that source E2 has been removed.
5. Energize the network of Fig -2 and measure the voltages indicated in Table (c). Calculate
currents using Ohm’s Law.
6. Now construct the network of Fig -3. Note that source E1 has been removed.
7. Energize the network of Fig -3 and measure the voltages indicated in Table (d). Calculate
currents using Ohm’s Law.
8. Using the results of steps # 3, 5 and 7, determine the power delivered to each resistor and insert
in Table (e).

Electrical Network Theory 5

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

OBSERVATIONS:

Resistors:

Nominal Values (Ω) Measured Values (Ω)

1 1K

2 430

3 2K

a) Calculated Values for the Network of Fig. 1

Due to E1 Due to E2 Algebraic Sum (∑)

I1 = I1 = I1 =

I2 = I2 = I2 =

I3 = I3 = I3 =

b) Measured Values for the Network of Fig. 1

V1 V2 V3 I1 I2 I3

c) Measured Values for the Network of Fig. 2

V1 V2 V3 I1 I2 I3

d) Measured Values for the Network of Fig. 3

V1 V2 V3 I1 I2 I3

e) Power Absorbed ( use measured values of I and V)

E1 & E2 Acting
Due to E1 Due to E2 Sum of Columns 1 & 2
Simultaneously

Electrical Network Theory 6

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

EXPERIMENT NO: 02
VERIFICATION OF THEVENIN'S THEOREM

OBJECTIVE:

To Verify Thevenin Theorem by finding its Thevenin’s Equivalent Circuit

REQUIRED:
1. VOM/DMM
2. Power Supply
3. Resistances (120Ω, 1k Ω, 390Ω)
THEORY:
Any linear circuit is equivalent to a single voltage source (Thevenin's Voltage) in series
with single equivalent resistance (Thevenin’s Equivalent Resistances)
The current flowing through a load resistance RL connected across any two terminals A
and B of a network is given

FIGURE:

Fig – 1

Fig – 2

Electrical Network Theory 7

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

Fig – 3
PROCEDURE:
1. Reduce the circuit by calculating the Thevnin equivalent resistance across the terminals A & B
2. Determine the Thevinin equivalent voltage across terminals “A” and “B” for 5V, 10V, 15V.
3. Now, combine the Thevenin voltage with its resistance determines across 120Ω, 1K Ω, and 390
Ω resistors.
TABLE-1:

VS R1 R2 R3 VTH RTH

5V

10V

15V
TABLE-2:
Vs VTH RTH RL IL
120
5V 390
1K

120
10V 390
1K

120
15V 390
1K

Electrical Network Theory 8

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

EXPERIMENT NO: 03

VERIFICATION OF MAXIMUM POWER TRANSFER THEOREM

OBJECTIVE:

To Verify Maximum Power Transfer Theorem

Discussion
Maximum power transfer theorem states that any linear network, if the load resistance equals its
Thevenin’s equivalent resistance, the load can yield a maximum power from sources.
Now we consider the Thevenin’s equivalent shown in Fig 1. By Ohm’s Law, the power dissipated in the Load PRL
can be expressed as follows.
I = ETH / (RTH + RL)

PRL = I2*RL

PRL = [ETH / (ETH + RL)2*RL

or

Figure-1

Suppose ETH = 4V and RTH = 5Ω, then PRL can be expressed by the equation PRL = 16 RL / (5+RL)2. Now we
calculate and record each of the PRL values for each RL value from 1 Ω to 9 Ω increasing the step to 1 Ω. The
results are listed in Table 1 and plotted in Fig 2. From both Table 1 and fig- 2, you can find that the maximum
value of PRL occurs at RL = RTH.

Electrical Network Theory 9

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

Table – 1

Figure -2
Procedure
1. Set the Module KL-13001 on the main KL-21001, and locate the block a.
2. According to Figs. 1 , complete the experiment circuit with short-circuit clips.
3. Apply +15V to +V.
Turn off the power switch.
4. Adjust VR1 to 250 Ω. (Let R1=RTH, VR1=Rl).
Turn on the power.
Measure and record the current flowing through VR1 as indicated by the milliammter.
I = ______________________________ mA.
Calculate and record the power dissipated by VR1 using the equation
2
PRL = I *RL. PRL =______________________________ W.
Turn off the power.
5. Adjust VR1 to 500 Ω and repeat step 4.
I = ______________________________ mA
PRL = ______________________________ W
6. Adjust VR1 to 1 K Ω and repeat step 4.
I = ______________________________ mA
PRL = ______________________________ W
7. Adjust VR1 to 1.25 K Ω and repeat step 4.
I = ______________________________ mA
PRL = ______________________________ W
8. Adjust VR1 to 1.5 K Ω and repeat step 4.
I = ______________________________ mA
PRL = ______________________________ W
9. Complete Fig. 4 by using you measured I and calculated PRL values.

Electrical Network Theory 10

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

EXPERIMENT NO: 04
To observe variation in impedance and current of an RC series network in ac circuit

Discussion

When an ac voltage is applied across a pure resistance, the resultant current is in phase with the applied
voltage. Resistance therefore has no phase angle associated with it and is written as R˂0. When an ac
voltage is applied across a pure capacitor, the resultant current leads the voltage by 90. Capacitance
therefore has a phase angle associated with it. The opposition that a capacitor offers to the flow of
alternating current is called capacitive reactance and is written as Xc˂ -90, or –jXc. The magnitude of Xc is
Xc=1/2π fC= 1/wC.

An RC series circuit with an ac supply voltage is shown Fig . The impedance of this circuit can be expressed as
ZT = Z1 + Z2 = R 0 +XC -90

The current in the across R is

ER = I R

The voltage across C is

EC = I X C

By Kirchhoff’s voltage law, then

ΣV =E-VR-VC = 0

Or +

Figure

Electrical Network Theory 11

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

Procedure
1. Set the module KL-13001 on the main unit KL-21001, and locate the block e.

2. According to Figs. 1 complete the experiment circuit with short-circuit clips. Apply the AC power 9V to
EA. Measure and record EA = ______________________________ V

3. Calculated and record the values below.

Reactance of C2 XC = ______________________________ Ω

Total impedance ZT = ______________________________ Ω

Current in circuit I = ______________________________ mA

Voltage across R8 R = ______________________________ V

Voltage across C2 EC = ______________________________ V

Power dissipated P = ______________________________ mW

4. Measure and record the values of ER and EC by using the ac voltmeter.

Voltage across R8 R = ______________________________ V

Voltage across C2 EC = ______________________________ V

Are you sure the measured values equal to the calculated values of step 3?

Yes NO

4. Using the equation + , calculate the applied voltage of the circuit.

EA = ______________________________ V

Does the calculated value equal the measured value of step 2?

Yes NO

If no, explain it.

_____________________________________________________________________________________

5. Using the measured values of ER and EC, calculate and record the current I.

I = ______________________________ mA

Does the calculated value equal the measured value of step 3?

YES NO

6. Using the values of R, XC and ZT, plot a vector diagram in space below.

Electrical Network Theory 12

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

EXPERIMENT NO: 05
To observe variation in impedance and current of an RL series network in ac circuit

Discussion

When an ac voltage is applied across a pure inductance, the current lags the voltage by 90 ̊ .Inductance
therefore has phase angle associated with it .The opposition that an inductance offers to the flow of alternating
current is called inductive reactance and may be expressed as , or j

The magnitude of is = 2πfL =2 L

An RL series circuit with an ac supply voltage is shown in Fig-1.The impedance of this circuit can be expressed as

The current in the circuit is

L =E/ (the current lags the voltage)
The voltage across R is
=l R
The voltage across l is
=I
By Kirchhoff s voltage law, then
V= E - - =0

Figure

Electrical Network Theory 13

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

Procedure
1. Set the module KL -13001 on the main unit KL-21001, and locate the block f, link 0.5H
inductance at L1 position.
2. According to Figure complete the experiment circuit with short –circuit clips. Apply the AC
power 9V to EA.
Measure and record EA. EA =_________________________V
3. Calculate and record the values below.

Reactance of L1 = ______________________________ Ω

Total impedance = ______________________________ Ω

Current in circuit I= ______________________________ mA

Voltage across R9 = ______________________________ V

Voltage across L1 = ______________________________ V

Phase angle = ______________________________

Power dissipated P= ______________________________ mW

4. Measure and record the values of = and =by Using the AC voltmeter.

Voltage across R9 = ______________________________ V

Voltage across L1 = ______________________________ V

5. Do the measured values equal the calculated values of step 3?
Yes No

6. Using the equation , calculate the applied voltage of the circuit

EA = ______________________________ V
Does the calculated value equal the measured value of step 2?
Yes No
If No explain it.

__________________________________________________________
________________________________________________________

Electrical Network Theory 14

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

EXPERIMENT NO: 06
To Observed and determine the Resonant Frequency of a resonant circuit

Discussion:
Figure shows an RLC series-parallel circuit with an ac power supply as mentioned before.

The capacitive reactance and inductive reactance very with frequency. Therefore, the
net impedance of the parallel circuit consisting of l2 and C3 will vary with input frequency. At

some frequency which we will define as the resonant frequency .the parallel circuit operates

in resonance and equals the resonant frequency can be expressed as

Figure

Procedure
1. Set the module KL -13001 on the main unit KL -21001, and locate the block h.
2. According to Figure, complete the experiment circuit with short –circuit clips.
The L2 is the 0.1H inductor provided.

3. Set the function selector of function generator to sine wave position .connect the oscilloscope to
the output of function generator.
Adjust the amplitude and frequency control knobs to obtain an output of 1 KHz,
5Vp-p and connect it to the circuit input (I/P).

4. Using the oscilloscope, measure and record the voltage acrossL2, C3 and R12.

Electrical Network Theory 15

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

= _____________________V p-p

= _____________________V p-p

= _____________________V p-p

5. Using the equation , calculate and record the resonant frequency

of the circuit.

=______________________Hz

6. Vary the output frequency of function generator to obtain a maximum value of

VAB.
Using the oscilloscope, measure and record the input frequency

= _____________________Hz

7. Is there agreement between the frequency value f and the resonant frequency of
step 5?
Yes No

Electrical Network Theory 16

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

EXPERIMENT 07

DC RC CIRCUIT AND TRANSIENT PHENOMENA

DISCUSSION

The capacitor is a element which stores electric energy by charging the charge on it. Bear in mind that the charge
on a capacitor cannot change instantly. Fig. 1 shows a basic RC circuit consisting a dc voltage, switch, capacitor,
and resistor. Assume that the voltage across C is zero before the switch closes. Even at the instant when the
switch closes (connecting to VR1 and letting VR1 = R), the capacitor voltage will still be at zero, and so the full
voltage is impressed across the resistor. In other words, the peak value of charging current which starts to flow is
at first determined by the resistor. That is, Io =V/R.

Figure -1

As C begins to charged, a voltage is built up across it which bucks the battery voltage, leaving less voltage for the
resistor. As the charging continues, the current keeps decreasing. The charging current can be expressed by the
-t/RC,
formula i= (V/R)έ where έ = 2.718. Fig.2 shows how the charging current varies with time.

Fig.3 shows how the resistor voltage VR and the capacitor voltage VC vary with time when it is charging. The
-t/RC,
capacitor voltage VC is expressed by VC = V(1- έ ) and the resistor voltage is VR = Vέ-t/RC by Kirchhoff’s
voltage law, V= VR+VC at all times.

Figure -2 Figure-3

Electrical Network Theory 17

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

For the moments we assume that the VC is equal to the battery voltage. The switch is switched to connect the C
and R7 in shunt. The capacitor then discharges through R7 (letting R7=R), so the discharging current, the resistor
voltage, and the capacitor voltage can be expressed by the following:

L = -(V/R) έ-t/RC VC = V έ-t/RC VR = V- έ-t/RC

Fig 4 shows how the discharging current varies with time. Fig.5 shows how the VR and VC vary with time when it
is discharging.

Figure – 4 Figure- 5

When the capacitor charges, the final value of Vc is determined solely by battery voltage, and how long it takes to
get there depends on the resistor and capacitor sizes. The value of RC product is referred to as the time constant
(T or TC) of the RC circuit. That is, T= RC, where T is second, R in ohm, and C in farad. If t= 1T, the capacitor
will build up to 63% of this final voltage. The time constant chart is shown in Fig.6 curve as the capacitor charge
voltage and curve B is the capacitor discharge voltage. In practice, at t = 5T, we can consider that the Vc charges
to V or Vc discharges to 0

Figure - 6

Electrical Network Theory 18

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

PROCEDURE

1. Set the module KL-21001, and locate the block d.

2. According to figs.1 And 7 complete circuit with short- circuit clips.

Figure - 7

3. Adjust VR1 to 1 KΩ. Turn the switch to VR1 position.

Connect the voltmeter across the capacitor C1.
Adjust the positive to +10V and apply it to circuit.
At this instant the capacitor C1 begins to charge and the capacitor voltage Vc1 increases and finally
reaches to 10V as indicated by the voltmeter.

4. Turn the switch to R7 position.

The capacitor begins to discharge and the Vc decreases to 0V.

5. Using the equation T= RxC and the values of VR1 and C1 calculate the time constant
T = _______________Sec.

6. Calculate the values of charging capacitor voltage Vc1 at t = 0T, 1T, 2T, 3T, 4T, and 5T and plot
them on the graph of fig.8.
Draw a smooth curve through these plotted points.

Electrical Network Theory 19

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

This will be a charging curve.

10

0 1 2 3 4 5

Figure-8

7. Use the stopwatch to count the time constant or oscilloscope.

Turn the switch VR1 position, measure and record the time when the charging capacitor voltage Vc1
reaches 6.32V as indicated by the voltmeter.
T=_____________Sec.
Note: Make sure Vc1= 0 before changing the capacitor each time.

8. Measure the values of Vc1 at time t= 1T, 2T, 3T, 4T, 5T, and record the result in table 1.
TABLE-1
Time (t) 0T 1T 2T 3T 4T 5T

VC1

9. Plot the recorded values of t and Vc1 on the graph of Fig.8, and then draw a smooth curve through
these plotted points.
10. Comparing the curves of steps 9 and 6, is there good agreement between the two
Yes No

Electrical Network Theory 20

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

11. Adjust VR1 to 200Ω.

Calculated and record the time constant T.
T= _________Sec.
Charge the capacitor and observe the charge in Vc1 indicated by the voltmeter.
Is the charging time shorter than that of step 3 for Vc1 = 10V?
Yes No

12. Turn the switch to the VR1 position.

Apply the power + 10V to charge the capacitor to Vc1 = 10V.

13. Turn the switch to R7 position. The capacitor will discharge through R7.
Calculated and record the time constant for discharging.
T =_________________Sec.
14. Repeat step 6 for discharging curve.
15. Measure and record the time that Vc1 decreases from 10V to 3.68V.
T =_________________Sec.
Comparing this result with step 13, is there agreement between the two?
Yes No

16. Repeat step 8 for discharging and record the result in table 2.
TABLE-1
Time (t) 0T 1T 2T 3T 4T 5T

VC1

17. Repeat step 9 for discharging curve.

18. Comparing the curves or steps 17 and 14, is there good agreement between the two? Yes No

Electrical Network Theory 21

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

EXPERIMENT 08
PULSE RESPONSE OF A SERIES RC NETWORK
EQUIPMENT
1. Signal generator
2. Oscilloscope
3. Capacitor: 0.1µF / 0.001µF
4. Resistor: 10KΩ / 20 KΩ
CIRCUIT DIAGRAM

THEORY
The step response of a network is its behaviors when the excitation is the step function. We use a square wave
source, which in fact repeats the pulse every ‘T’ Seconds and allows a continuous display of repetitive responses
on a normal oscilloscope.

Charging a capacitor
We investigate the behavior of a capacitor when it is charged via a high resistor. At the instant when step voltage
is applied to the network, the voltage across the capacitor is zero because the capacitor is initially uncharged. The
entire applied voltage v will be dropped across the resistance R and the charging current is maximum.
But then gradually, voltage across the capacitor starts increasing as the capacitor start to charge and the charging
current starts decreasing. The decrease of the charging current and the increase of voltage across the capacitor
follow exponential law.
I(t) = V/R e-t/RC
However, the voltage across the capacitor is given by,
VC (t) = V (1- e-t/RC)
Where t= time elapsed since pulse is applied
τ = RC= Time constant of the circuit

Electrical Network Theory 22

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

Discharging a charged Capacitor

During the next half cycle of pulse, when the pulse amplitude is zero and capacitor is charged to potential
difference of V volts, now the capacitor discharges through resistor R. So, the voltage across capacitor decreases
exponentially and the discharge current rises instantly to a maximum value i.e Im=V/R and then decays
exponentally. Mathematically, it can be shown that voltage across the capacitor and discharging current are given
value by,
VC (t) = V e-t/CR
I(t) = -Im e-t/RC

Electrical Network Theory 23

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

PROCEDURE:
1. Set the out of the function generator to a square wave with frequency 500Hz and peak to peak amplitude
5V.
2. Wire the circuit on bread board.
3. Display simultaneously voltage Vin (t) across the function generator (on CH1) and VC (t) across the
capacitor C (on CH2).
4. Sketch the two measure wave forms Vin(t) and Vc (t), calculate and sketch the waveforms, VR(t) and I (t).
Label the time, voltage and current scales note that the voltage across the R is VR (t) also represents the
current I (t).
5. Measure the time constant τ, using the waveform VC (t). Expand the time scale and measure the time it
takes for the waveform to complete 63% of its total change, i.e 5V. Enter the measured value of τ in table.

6. Computer values of theoretically expected and experimentally obtained time constants τ.

Max frequency input pulse that can be applied:

If the pulse width is at least five time constant in length, the capacitor will have sufficient time to charge and
discharge when the pulse returns to 0 volts. Any increase in frequency beyond this will result in insufficient time
for the charge/discharge cycle to complete. This frequency is the max frequency of input pulse that can be
applied.

So min pulse width should be equal to 5RC and form this max frequency can be calculated.

Electrical Network Theory 24

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

OBSERVATION AND CALCULATIONS

Table-1

No. R C τ 5τ F

1 20KΩ 0.001µF

2 10KΩ 0.001µF

Charging of Capacitor
Table 2

Number of Time Constant Calculated Voltage Vc(volts) Measured Voltage Vc(volts)

1τ

2τ

3τ

4τ

5τ

Discharging of Capacitor
Table 3

Number of Time Constant Calculated Voltage Vc(volts) Measured Voltage Vc(volts)

1τ

2τ

3τ

4τ

5τ

Electrical Network Theory 25

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

WAVEFORMS OF VOLTAGES& CURRENTS

Vin (volts)

Time t (sec)

VC (volts)

Time t (sec)

I(t) (amps)

Time t (sec)

VR (volts)

Time t (sec)

Electrical Network Theory 26

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

EXPERIMENT 09
PULSE RESPONSE OF A SERIES RL NETWORK
EQUIPMENT
1. Signal generator
2. Oscilloscope
3. Inductor:100mH
4. Resistor: 10KΩ /20KΩ

CIRCUIT DIAGRAM

THEORY

This lab is similar to the RC circuit lab except that an Inductor replaces the capacitor. In this experiment we apply
a square waveform to the RL circuit to analyze the transient response of the circuit. The pulse –width relative to
the circuit’s time constant determines how it is affected by the RL circuit.

Rise of current

At the instant when step voltage is applied to an RL network, the current increases gradually and takes some time
to reach the final value. The reason the current does not build up instantly to its final value is that as the current
increases, the self-induced e.m.f in L opposes the change in current (Lenz’s Law). Mathematically, it can be
shown,

I(t) = V/R (1-e-t/τ)

Where t= time elapsed since pulse is appliad
τ= L/R= time constant of the circuit

Electrical Network Theory 27

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

(ii) Decay of the current

During the next half cycle of the pulse, when the pulse amplitude is zero, the current decreases to zero
exponentially. Mathematically, it can be shown,

I(t) = V/R e-t/τ

PROCERURE

1. Set the output of the function generator to a square-wave with frequency 2 KHz and peak-to-peak
amplitude 5V.
2. Wire the circuit on breadboard.
3. Display simultaneously voltage Vin (t) across the function generator (on CH 1) and VL (t) across the
inductor L (on CH 2).
4. Sketch the two measured waveform Vin (t) and VL (t), calculate and sketch the waveform, VR (t) and I(t),
Label the time, voltage and current scales. Note that the voltage across resistor R, VR (t), also represents
the current I(t).
5. Measure the time constant, τ using the wave form VR (t). Expand the time scale and measure the time it
takes for the waveform to complete 63% of its total change, i.e. 5V. Enter the measured value of τ in
Table.
6. Compare values of the theoretically expected and experimentally obtained time constants τ.

Electrical Network Theory 28

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

OBSERVATION AND CALCULATIONS

Table-1

No. R L τ 5τ FMAX

1 20KΩ 100 mH

2 10KΩ 100 mH

Rise of Current
Table 2

Number of Time Constant Calculated Current (Amps) Measured Current (Amps)

1τ

2τ

3τ

4τ

5τ

Decay of Current
Table 3

Number of Time Constant Calculated Current (Amps) Measured Current (Amps)

1τ

2τ

3τ

4τ

5τ

Electrical Network Theory 29

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

WAVEFORMS OF VOLTAGES& CURRENTS

Vin (volts)

Time t (sec)

VL (volts)

Time t (sec)

I(t) (amps)

Time t (sec)

VR (volts)

Time t (sec)

Electrical Network Theory 30

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

EXPERIMENT 10
TO SHOW THE FREQUENCY RESPONSE OF A SERIES RLC NETWORK AND SHOW THAT THE
RESONANT FREQUENCY OF A SERIES RLC CIRCUIT IS GIVEN BY 1/2T LC.

EQUIPMENT
1. Signal Generator
2. Inductor: 100-200 mH
3. Capacitors: 0.001µF and 0.01µF
4. Resistor: 100Ω 5 percent
5. Oscilloscope
6. Multimeter

CIRCUIT DIAGRAM

THEORY

As shown in the circuit diagram, resistor, inductor and capacitor are connected in series with an a.c. supply of
r.m.s. voltage V. The Phasor diagram is plotted as,
B

D
V
VL-VC

A
O VR
-VC

Electrical Network Theory 31

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

Let VR = IR = voltage drop across R

VL= IXL = voltage drop across L
VC = IXC = voltage drop across C

In voltage triangle of fig 1, OA represents VR, AB and AC represents the inductive and capacitive drop
respectively. It will be seen that VL and Vc are 180 degree out of phase with each other i.c. they are in direct
opposition to each other.
Subtracting AC from AB, we get the net reactive drop AD = I(XL – XC)

The appliad voltage V is represented by OD and is the vector sum of OA and AD.

OD = √ (OA2 + AD2)

V = √ [(IR)2 + ( IXL - IXC )2 ] = I √ [(R)2 + ( XL - XC )2 ]

I = V/√ [(R)2 + ( XL - XC )2 ] = V/Z

The term is known [(R)2 + ( XL - XC )2 ] as the impedance of the network. Obviously,

(Impedance)2 = (Resistance)2 + (Net Reactance)2

Resonance in RLC Networks

Resonance means to be in step with. When the appliad voltage and the current in an a.c. network are in step with
i.e. phase angle between voltage and current is zero or pf = 1, the circuit is said to be in resonance.
An a.c. circuit containing reactive element (L and C) is said to be in resonance when the net reactance is zero.
When a series R-L-C is in resonance, it possesses minimum impedance Z = R. Hence, circuit current is maximum,
it being limited by value of R alone. The current Io = V/R and is in phase with V. since circuit current is
maximum, it produces large voltage drops across L and C. but these drops being equal and opposite, cancel out
each other. Taken together, L and C from part of a circuit across which no voltage develops however, large the
current flowing. If it were for the presence of R, such a resonant circuit would act like a short circuit to currents of
the frequency to which it is often referred to as voltage resonance.
The frequency at which the net reactance of the series circuit is zero is called the resonant frequency. Its value can
be found as found as under:
XL- XC = 0
XL = XC or ωoL =1/ ωoC
ωo2=1/LC or (2πfo)2 = 1/ LC or fo=1/2π√LC
If L is in Henry and C is in Farad, then fo is in Hertz

Electrical Network Theory 32

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

PROCEDURE
1. For the given inductor and capacitor calculate the resonant frequency and connect the circuit as shown in
circuit diagram
2. Apply sinusoidal signal from the generator of the 5V pk to the network and set the frequency to a value of
500 Hz
3. Observe VR, VL and VC on the oscilloscope and record it.
4. Increase the frequency of the signal and for each frequency measure and record V, VR, VL and VC and
maintain applied voltage constant at 5VP
5. Now measure VR, VL and VC theoretically and compare the results.

OBSERVATIONS &CALCULATIONS
Vrms= VP/√2
Calculated value
No. Frequency f (Hz) XL (ohms) XC (ohms) Z (ohms) I=VR/R VL=IXL (Volts) VC=IXC
(Amps) (Volts)

Measured Values
No. Frequency f (Hz) XL (ohms) XC (ohms) Z (ohms) I=VR/R VL=IXL (Volts) VC=IXC
(Amps) (Volts)

Electrical Network Theory 33

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

GRAPH

I (Amps)

f (Hz)

Z (ohms)

f (Hz)

Electrical Network Theory 34

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

EXPERIMENT 11(a)
SINUSOIDAL RESPONSE OF RL CIRCUIT
APPARATUS
1. Signal generator
2. Oscilloscope
3. Multimeter
4. Inductor 100 mH
5. Resistor 2K

CIRCUIT DIAGRAM

THEORY

Circuit containing inductance and resistance appear in variety of electronic circuits, from power supplies
to filters. In this experiment we are going to investigate the sinusoidal response of a series RL circuit. A difficulty
arises in conjunction with such circuit in that real conductor are not like ideal conductor we deal in our theory.
Since they are formed of coiled wire, they possess resistance as will as inductance. Furthermore their resistance
is dependent on frequency as will. As a consequence, the inserted R does not represent the total resistance of the
circuit. In addition, when we measure the voltage across a coil, we are getting both inductive and resistive
component of voltage, not simply VL. In this experiment, we will try to overcome this problem by making R
large compared with the ac resistance of coil, that is we will presume the coil is ideal.

Relation for steady state ac analysis are as follows

ZL =j2πfL
ZTOTAL = R+ZL
I = Vin / ZTOTAL
VR = IR
VL = IZL

Electrical Network Theory 35

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

PROCEDURE

1. Calculate and note down quantities ZL, Z TOTAL, I, VR and VL for a source voltage of 5V peak and
frequency 1 KHz. Remember to use Vrms = VP/√2 in calculations.
2. Connect the circuit as shown in diagram and adjust the function generator voltage and frequency to the
values chosen above.
3. Use Multimeter to measure voltages VL and VR and note down in Table.
4. Compare measured and calculated values.
5. Explain any discrepancies between measured and calculated values of VR and VL.
6. Draw a phasor diagram of the calculated voltages in diagram. Include I as a reference phasor and show
the position of VR and VL.

OBSERVATONS AND CALULATIONS

Table 1
CALCULATION PARAMETERS
ZL ZTOTAL I VR VL

Table 2
MEASURED
I= VR/R ZL =VL/I Z=Vi/I
VR VL

Electrical Network Theory 36

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

EXPERIMENT 11(b)
SINUSOIDAL RESPONSE OF RC CIRCUIT
APPARATUS
1. Signal generator
2. Oscilloscope
3. Capacitor 0.1µF
4. Resistor 2K
CIRCUIT DIAGRAM

PROCEDURE

(Similar to the above part, except a capacitor replaces inductor)

1. Calculate and note down quantities ZC, ZTOTAL, VR and VC for a source voltage of 5V peak and
frequency 1 KHz. Remember to use Vrms = Vp/√ 2 in calculations
2. Connect the circuit as shown in diagram and adjust the function generator voltage and frequency to the
values chosen above.
3. Use Multimeter to measure voltages VC and VR and note down in Table.
4. Compare measured and calculated values.
5. Explain any discrepancies between measured and calculated values of VR and VC.
6. Draw a phasor diagram of the calculated voltages in diagram. Include I as a reference phasor and show
the positions of Vi, VR and VC .

Electrical Network Theory 37

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

OBSERVATIONS AND CALCULATIONS

Table 1
Calculation Parameters
ZC ZTOTAL I VR VC

Table 2
Measured
I= VR/R ZC= VC/I Z =Vi/ I
VR VC

Electrical Network Theory 38

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

EXPERIMENT 12
FREQUENCY CHARACTERISTICS OF A SIMPLE LOW PASS RL FILTER CIRCUIT AND TO UNDERSTAND THE
BEHAVIOR OF THE CIRCUIT WITH RELATION TO THE POLE ZERO LOCATION.

APPARATUS
1. Signal generator
2. Oscilloscope
3. Multi-meter
4. Inductor 100 mH
5. Resistor 2K
CIRCUIT DIAGRAM

THEORY

By using various combinations of resistances capacitor and inductor we can make circuit that have the
property of passing or rejecting either low or high frequencies or bands or frequencies. These frequency selective
networks, which alter the amplitude and phase characteristics of the input ac signal, are called fillers. Or in other
words,
“A filter is an AC circuit that separates some frequencies from other in within maxid-frequency signals.”
A basic RL low-pass filter is shown in figure. Notice that the output voltage is taken across the resistor.

When the input is dc (0 Hz) the output voltage ideally equals the input voltage because XL is a short circuit. As
the input frequency is increased, XL increases and as a result V out gradually decreases unit the critical frequency is
reached. At this point, XL = R and the frequency is

Electrical Network Theory 39

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

2πfCL =R
fc = R/2πL
fc = 1/2π(L/R)
just as in the RC low-pass filter, Vout = 0.707 Vin and, thus the output voltage is down 3dB at the critical
frequency.
The RL low-pass filter acts as a lag network. The phase shift from input to output is expressed as
θ = - tan-1 (XL/R)
At the critical frequency, XL = R and, therefore, θ = -45o. as the input frequency is reduced as decreases and
approaches 0o as the frequency approaches zero as shown in figure

PROCEDURE

1. Apply a 1 Vpp 100Hz signal as input to the network and measure the corresponding output
voltage level. Determine the decibel gain of the filter.
G (dB) = log [Vo/Vin]
2. Determine the phase difference between Vo and Vin in degrees.
3. Repeat step 1 and 2 for the following frequencies: 200 Hz, 500Hz, 1 KHz, 1.5 KHz, 2 KHz,
3 KHz, 5 KHz, 10 KHz, 20 KHz, 50 KHz.

Electrical Network Theory 40

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

OBSERVATIONS AND CALCULATIONS

fc =

No Input frequency Input voltage output voltage Vo /Vin db =(20 log θ (degrees)
f(Hz)
Vin RMS(volts) Vo RMS(volts) (volts) Vo /Vin

Electrical Network Theory 41

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

EXPERIMENTS 13
FREQUENCY CHARACTERISTICS OF A SIMPLE HIGH PASS RL FILTER CIRCUIT AND TO UNDERSTAND THE
BEHAVIOR OF THE CIRCUIT WITH RELATION TO THE POLE ZERO LOCATION.

APPARATUS
1. Signal generator
2. Oscilloscope
3. Multi-meter
4. Inductor 100 mH
5. Resistor 1.5K
CIRCUIT DIAGRAM

THEORY

A high pass filter allows signals with higher frequencies to pass from input to output while rejecting lower
frequency considered to be lower end of pass band is called the critical frequency. It is the frequency at which the
output is 70.7%of the maximum.
A basic RL high-pass filter is shown in figure. Notice that the output is taken across the inductor.

When the input frequency is at its critical value, XL =R, and the output voltages is 0.707Vin. As the frequency
increases above fc, XL increases and, as a result, the output voltages increase until it equal Vin. The expression for
the critical frequency of the high-pass filter is the same as for the low-pass filter.

Electrical Network Theory 42

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

fc =

Frequency characteristics of high pass filter is shown below

Both the RC and the RL high-pass filter act as lead network. Recall from previous experiments that the phase shift
from input to output for the RC lead network is:

θ =tan-1[ ]

And for the RL lead network is:

θ = 90o – tan -1 [ ]

At the critical frequency, XL = R and, therefore, θ = 45o. As the frequency is increased, θ decreases toward 0o as
shown in figure.

PROCEDURE
1. Apply a 10 Vpp 100 Hz signal as input to the network and measure the corresponding output voltage level.
Determine the decibel gain of the filter.
G (db) = 20 log [Vo/ Vin]
2. Determine the phase difference between Vo and Vin in degrees.
3. Repeat step 1 and 2 for the following frequencies: 200 Hz, 500Hz, 1KHz, 1.5 KHz, 2KHz, 3kHz, 5 KHz,
10 KHz, 20KHz, 50 KHz.

Electrical Network Theory 43

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

OBSERVATIONS AND CALCULATIONS

fc = Vin

No Input frequency f(Hz) Input voltage Vin Output voltage Vo/ Vin dB =(20 θ
RMS(volts) Vo RMS(volts) (volts) log Vo/ Vin) (degrees)

Electrical Network Theory 44

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

EXPERIMENT 14
TO PLOT THE MAGNITUDE AND PHASE RESPONSE OF A SERIES RESONANAT BAND FILTER

APPARATUS
1. Signal Generator
2. Oscilloscope
3. Multimeter
4. Capacitor: 0.01µ F
5. Inductor 100-200 mH
6. Resistors (1/4W): 1KΩ±5 percent

CIRCUIT DIAGRAM

THEORY

BAND PASS FILTER

It allows a certain band of frequencies to pass and attenuates or rejects all frequencies below and above the pass
band. A combination of low-pass and high-pass filter can be used to form band pass filters.

Low pass High pass

Vin Filter Filter Vout

Low-pass and high-pass filters used to form a band-pass filter

Electrical Network Theory 45

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

OPERATION OF SERIES RESONANT BAND PASS FILTERS

A series resonant filter has minimum input impedance. At critical frequency the inductor and the capacitor in
series behave a simple resistor. Hence making of maximum output a cross the load resister. At the frequency other
then resonant frequency, reactance offered by the inductor or capacitor is very large, hence output voltage will be
very small at high as well as at low frequencies.
BANDWIDTH
The bandwidth of a band pass filter is the range of frequencies for which the current, and therefore the output
voltage, is equal or greater than 70.7 percent of its value at the resonant frequency.

Mathematically bandwidth = Resonant Frequency fr

Quality Factor q
QUALITY FACTOR
Quality factor is the ratio of reactive power developed in inductor or capacitor to average power the dissipated in
resistor.
Quality factor = Reactive power developed in inductor or capacitor
Average power dissipated in resistor
Quality factor indicates the selectivity of the filter and can be expressed as,
Quality factor = ώL/R
= 2πfrL/R
PROCEDURE
1. For the components used in the circuits, calculate and record the resonant frequencies for the circuit in the
fig. Calculate, also, the circuit-Q and bandwidth of the circuit.
2. Construct the circuit shown in fig
3. At a frequency of 500 Hz adjust Vin to some convenient value, such as 5V rms.
4. Use Multi-meter to measure Vo and record it in table.
5. Vary the frequency, measure and record Vo while maintaining constant.
6. Complete the decibel gain row of the table.
7. Plot the decibel voltage in ratio versus log frequency

Electrical Network Theory 46

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

OBSERVATION&CALCULATION
Resonant Frequency fr = 1/2π√LC
Quality Factor Q = ώL/R
Bandwidth = fr/Q
No. Input frequency f(Hz) Input voltage Vin Output voltage Vo/Vin db= 20log
(volts) Vo (volts)
(volts) (Vo/ Vin)

Electrical Network Theory 47

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

EXPERIMENT NO 15
TO PLOT THE MAGNITUDE AND PHASE RESPONSE OF A SERIES RESONANT BAND-STOP FILTER.

APPARTUS
1. Signal Generator
2. Oscilloscope
3. Multi-meter
4. Capacitor 10µF
5. Inductor 100 to 200 M Hz
6. Resistor (1/4W): 500Ω 1K Ω ±4%

CIRCUIT DIAGRAM

THEORY

BAND STOP FILTER

It is a filter that rejects a certain band or range of frequencies while passing all frequencies below and above the
rejected band. Band stop filters block signals occurring between two given frequencies, FL and FH.

It can be made out of a low-pass and a high pass filter by connecting the two filter sections in parallel with each
other instead of in series.
Passes Low Frequencies

Low-Pass Filter

Signal Input Signal Output

High-Pass Filter

Passes High Frequencies

Electrical Network Theory 48

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

OPERATION OF BAND STOP FILTER

When the series LC combination reaches resonance, its very low impedance shorts out the signal,
dropping it across resistor R1 and preventing its passage on to the load. Thus, within the band at which
the resonant frequencies occur there is a relatively less output and that set of frequencies are attenuated.

At frequencies other the resonant frequencies, the reactance offered by inductor and capacitor is very
large, thus outside the band at which resonant frequency occurs, there is large output and that set of
frequencies or passed to the output.

CORNER FREQUENCY
Because a real filter rolls off gradually, you usually specify the corner frequency as the frequency at
which the response is 1/√2(0.707) of that in the pass band. Because electronics engineer traditionally
describe relative signal strengths in decibels, the frequency is also referred to as 3-db point.

PROCEDURE

1. For the components used in the circuits, calculate and record the resonant frequencies for the
circuit in the fig. Calculate, also, the circuit-Q and bandwidth of the circuit.
2. Construct the circuit shown in fig
3. At a frequency of 500 Hz adjust Vin to some convenient value, such as 5V rms.
4. Use multi-meter to measure Vo and record it in table.
5. Vary the frequency, measure and record Vo while maintaining constant.
6. Complete the decibel gain row of the table.
7. Plot the decibel voltage in ratio versus log frequency

Electrical Network Theory 49

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

OBSERVATION & CALCULATION

Resonant Frequency fr = 1/2π√LC
Quality Factor Q = ώL/R
Bandwidth = fr/Q

No. Input frequency Input voltage Vin Output voltage Vo/Vin db= 20log
f(Hz) (volts) Vo (volts) (volts) (Vo/ Vin)

Electrical Network Theory 50

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

EXPERIMENT NO 16
TO VERIFY THE PRINCIPLE OF SUPER POSITION USING AC AND DC SOURCES

APPARATUS
1. Signal Generator
2. DC power Supply
3. Oscilloscope
4. Capacitor 0.1µF
5. Resistor 20 K

CIRCUIT DIAGRAM

THEORY
We often encounter circuits in which voltage and currents are made of both AC and DC components, i.e. they are
energized from DC and AC sources simultaneously. Signals and such circuitry are often referred to as “AC riding
on top of DC” and we can examine this behavior with the help of an Oscilloscope.

To analyze such circuits, the technique of super position may be employed. This involves analyzing the circuits
separately for each source in it by “killing” the remaining sources. Recall the voltage source or treated as short
circuits and current sources as open circuits.

In many applications, the capacitor in a circuit has such a low reactance at the operating frequency that it
can be considered it short circuit. To a DC sources, it is treated as an open circuit, of course. These simple ideas
allow us to analyze circuits with combined DC/AC signal sources very easily.
In this experiment we are going to look at a circuit that contains such a combination of sources. In
addition it will contain only resistors and capacitors. Frequency will be selected in such a way that capacitive
reactance is a small enough to be ignored.

Electrical Network Theory 51

Federal Urdu University of Arts, Science & Technology Islamabad – Pakistan Electrical Engineering

PROCEDURE

1. Use principle of superposition to calculate the DC and AC components of voltage across R and C. Take
f= 10KHz. Treat C as an open for DC and as a short for AC to facilitate your calculations
2. Set the output of function generator 1V rms sine wave and frequency 10 KHz. Also set the output of DC
supply equal to 2V.Connect the circuit as shown in diagram. (You can also use DC offset knob on
function generator instead of using DC supply. For that purpose connect oscilloscope across function
generator with output 1V rms sine wave. Now change the DC offset and observe the effect on
oscilloscope. Adjust the offset knob until you see a sine wave riding on a DC level of 2V with peak to
peak value of 2.8V approximately).
3. Connect the oscilloscope probes across terminal A and B, set it for DC coupling and observe the wave
form. You should see a sine wave riding on DC level of 2V. Sketch the wave form in your note book.
4. Change to AC coupling and note the effect.
5. Using multi-meter, measure both the DC and AC Voltage across R and C.
6. Record these values in table 1.you can also confirm your reading using oscilloscope.
7. Now connect the oscilloscope probes across R and observe the waveform. Change the coupling from DC
to AC and AC to DC and observe the effect. Also sketch the waveform.
8. Now adjust the frequency of the generator to 1 KHz, and if necessary, re-adjust the terminal voltage
components (DC and AC) to their original values just as instep 2.
9. Again measure AC and DC voltage across R and C using multi-meter and record in table 2. Why are
things so different when the frequency is changed to 1 KHz
OBSERVATION AND CALCULATIONS
Table-1
f = 10KHz Vc VR

dc ac dc ac

Calculated

Measured

Table-2
VC VR

dc ac dc ac

Electrical Network Theory 52