Scribd
Upload
19 views4 pages

Experiment 6

The lab report details an experiment on non-inverting configurations of operational amplifiers, focusing on understanding their functionality and gain calculation. The experiment involved setting up a circuit with specific resistors and using an oscilloscope to observe the output waveform, confirming that the output signal maintained the same phase and was amplified as expected. The findings emphasize the importance of non-inverting amplifiers in electronic systems for signal amplification.

Uploaded by

Naimul Hasan Tanmoy
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
19 views4 pages

Experiment 6

The lab report details an experiment on non-inverting configurations of operational amplifiers, focusing on understanding their functionality and gain calculation. The experiment involved setting up a circuit with specific resistors and using an oscilloscope to observe the output waveform, confirming that the output signal maintained the same phase and was amplified as expected. The findings emphasize the importance of non-inverting amplifiers in electronic systems for signal amplification.

Uploaded by

Naimul Hasan Tanmoy
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd

Lab Report

Course Code : EEE 230.10


Course Title : Electronics Laboratory
Semester : Fall 2024

Experiment No. : 06
Experiment Name : Study of Non-Inverting Configurations of Operational Amplifier
with a specific gain.

Submitted By: Submitted To:


Name: S. M. NAIMUL HASAN TANMOY Name: Md. Manzurul Hasan
Student ID: 2023000500001 Designation: Lecturer
Batch: 40 Department: EEE
Shift: Regular

Date of Performance: 13/01/2025

Date of Submission: 30/01/2025


Objectives:
In this experiment, I aimed to:
1. Learn how a non-inverting amplifier works using an operational amplifier
(Op-amp).
2. Understand how to calculate and measure the gain of a non-inverting
amplifier.

Theory:
A non-inverting amplifier is a circuit where the input signal is applied to the
non-inverting terminal (+) of the Op-amp. This means that the output signal
remains in the same phase as the input signal.
The gain of a non-inverting amplifier is given by the formula:
𝑅𝑓
𝐺𝑎𝑖𝑛 = 1 +
𝑅𝑖𝑛
Where:
Rf Is the feedback resistor.
Rin Is the input resistor.
Since the gain is always greater than 1, this type of amplifier is used when we
need to increase the strength of a signal without changing its phase.

Equipment :
1. A breadboard to build the circuit.
2. Connecting wires to link components.
3. Two DC power sources to power the Op-amp.
4. A signal generator to provide the input signal.
5. An oscilloscope to observe input and output waveforms.
6. Resistors (2kΩ and 1kΩ) for setting the gain.
7. An IC 741 Op-amp as the main component.

Procedure:
1. I set up the circuit on the breadboard according to the given diagram.
2. I connected a 2kΩ resistor as the feedback resistor and a 1kΩ resistor as
the input resistor.
3. The input signal was connected to Pin 3 (the non-inverting terminal) of
the Op-amp.
4. I connected Pin 2 (the inverting terminal) to the resistor network.
5. Pin 7 and Pin 4 were connected to DC power sources to power the Op-
amp.
6. Pins 1, 5, and 8 were left unconnected, as required.
7. I used an oscilloscope to observe the input and output waveforms:
Channel 1 was connected to the input signal.
Channel 2 was connected to Pin 6 (the output).
8. compared the observed output with the expected gain calculation.

Results and Observations:


The output waveform followed the same phase as the input waveform.
The output voltage was greater than the input voltage, as predicted by the gain
formula.
The measured gain was close to the calculated value.
Discussion:
In this experiment, I successfully built and tested a non-inverting amplifier
using an Op-amp. The results confirmed that the amplifier increases the input
signal without changing its phase. Understanding this circuit is important for
designing electronic systems that require signal amplification.

You might also like