CONNECT 2 NA 09.

92 B
09 - 2010
COMMUNICATION PROTOCOL 3991051.01

A) Communication medium
● RS485
3-pin connector on terminal 1 of terminal block J11: A or +
terminal 2: B or –
terminal 3: connected to earth for shielding if desired
Two lights provide information on the status of the transmission
- D50 → Receive LED. Usually off; flashes when a message is received by the board.
If this light remains on, the bus is reversed. Swap terminals 1 and 2 on J11.
- D52 → Send LED. Usually off; lights up when the CPU sends a message over the bus.
Main control board for machines with one non-reversible refrigerating circuit
J11 J10 J9

3 2 1 3 2 1 3 2 1 12 11 10 9 8 7 6 5 4 3 2 1 11 10 9 8 7 6 5 4 3 2 1

J7 J5
D50 D52 D46 D48
4321 4321

12 11 10 9 8 7 6 5 4 3 2 1 11 10 9 8 7 6 5 4 3 2 1
J12

W3
J8 J6
J13

7531
8642
J14

+
PL1 SP1
TR1

1 2 3 4 5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3

J2 J3 J4

B) Transmission mode
● Serial, asynchronous, half duplex, RTU mode.
- 1 start bit,
- 8 data bits,
- The parity is set via parameter P702,
The number of stop bits is set via parameter P703,
- The transmission speed is set via parameter P701,
- The unit number on the bus is set via parameter P705.
● Coding of analogue values
Standard 32-bit IEEE format (2 registers).
Order of values:
- If P704 = No → Low order, high order.
- Si P704 = Yes → High order, low order.
● Function codes used.
1 or 2: read n bits
3 or 4: read multiple registers (16 bits)
5: write one bit …………..
6: write register function………
8: read diagnostics counters
11: read event counter
15: write n bits
16: write multiple registers (16 bits)
Note: the write functions are enabled if parameter P103 is set to "Remote, BMS…"
● Error codes:
1: function code unknown
2: address incorrect
3: data error

1/28
 NA 09. 92 B
CONNECT 2
09 - 2010
COMMUNICATION PROTOCOL 3991051.01

REGISTERS ACCESSIBLE BY CUSTOMER

Register No. Register No.

Description Format Type Setting
hexadecimal decimal

Registers accessible in read-only mode (Functions 3 or 4)

0x01 1 Controller name Decimal Read-only 33 = Connect 2
0x02 2 Actual operating mode Decimal Read-only
0x3 and 0x4 3 and 4 Outdoor temperature Float Read-only
0x5 and 0x6 5 and 6 Control setpoint Float Read-only
0x7 and 0x8 7 and 8 Evaporator inlet temperature Float Read-only
0x9 and 0xa 9 and 10 Evaporator outlet temperature Float Read-only
0xb and 0xc 11 and 12 Condenser temperature Float Read-only

0x20 and 0x21 32 and 33 P285 Heating mode runtime (in hours) Float Read-only
0x22 and 0x23 34 and 35 P286 Cooling mode runtime (in hours) Float Read-only
0x24 and 0x25 36 and 37 P287 Pump 1 runtime (in hours) Float Read-only
0x26 and 0x27 38 and 39 P288 Pump 2 runtime (in hours) Float Read-only
0x28 and 0x29 40 and 41 P310 Number of starts, stage 1, circuit 1 Float Read-only
0x2a and 0x2b 42 and 43 P311 Stage 1, circuit 1 runtime Float Read-only
0x2c and 0x2d 44 and 45 P313 Number of starts, stage 2, circuit 1 Float Read-only
0x2e and 0x2f 46 and 47 P314 Stage 2, circuit 1 runtime Float Read-only
0x30 and 0x31 48 and 49 P340 Number of starts, stage 1, circuit 2 Float Read-only
0x32 and 0x33 50 and 51 P341 Stage 1, circuit 2 runtime Float Read-only
0x34 and 0x35 52 and 53 P343 Number of starts, stage 2, circuit 2 Float Read-only
0x36 and 0x37 54 and 55 P344 Stage 2, circuit 2 runtime Float Read-only

Registers accessible in read mode (Functions 3 or 4) and write mode (Function 16

0x101 and 0x102 257 and 258 P121 Cooling setpoint 1 Float Read/Write
0x103 and 0x104 259 and 260 P122 Cooling setpoint 2 Float Read/Write
0x105 and 0x106 261 and 262 P123 Heating setpoint 1 Float Read/Write
0x107 and 0x108 263 and 264 P124 Heating setpoint 2 Float Read/Write
0x109 and 0x10a 265 and 266 P125.1 Setpoint for 4 mA in cooling mode Float Read/Write
0x10b and 0x10c 267 and 268 P125.2 Setpoint for 4 mA in heating mode Float Read/Write
0x10d and 0x10e 269 and 270 P126.1 Setpoint for 20 mA in cooling mode Float Read/Write
0x10f and 0x110 271 and 272 P126.2 Setpoint for 20 mA in heating mode Float Read/Write

Registers accessible in read mode (Functions 3 or 4) and write mode (Functions 6 or 16)
0x200 512 Year Decimal Read/Write 0 to 99
0x201 513 Month Decimal Read/Write 1 to 12
0x202 514 Day of the month Decimal Read/Write 1 to 31
0x203 515 Day of the week Decimal Read/Write 1 to 7 (1: Monday, 2: Tuesday, etc.)
0x204 516 Hours Decimal Read/Write 0 to 23
0x205 517 Minutes Decimal Read/Write 0 to 59

2/28
 NA 09. 92 B
CONNECT 2
09 - 2010
COMMUNICATION PROTOCOL 3991051.01

CUSTOMER ACCESS BITS

Hexadecimal Bit No.

Description Type Setting
bit No. decimal

Read-only bit (functions 1 or 2)

0x01 1 P103 Control type Read-only 0: Local, 1: Remote
Operating summary (On/Off and automatic operation
0x02 2 Read-only 1 = On
input closed)
0x03 3 State of pump 1 output Read-only 1 = On
0x04 4 State of pump 2 output Read-only 1 = On
0x05 5 Output state, stage 1, circuit 1 Read-only 1 = on
0x06 6 Output state, stage 2, circuit 1 Read-only 1 = On
0x07 7 Output state, stage 1, circuit 2 Read-only 1 = On
0x08 8 Output state, stage 2, circuit 2 Read-only 1 = On
0x09 9 State of auxiliary electric heater 1 or boiler Read-only 1 = On
0x0a 10 State of auxiliary electric heater 2 Read-only 1 = On
0x0b 11 State of auxiliary electric heater 3 Read-only 1 = On
0x0c 12 State of auxiliary electric heater 4 Read-only 1 = On
0x0d to 0x0f reserved
0x10 16 General fault summary (1 fault below present) Read-only 1 = Fault
0x11 17 Phase controller fault Read-only 1 = Fault
0x12 18 Water flow fault Read-only 1 = Fault
0x13 19 Pump 1 fault
0x14 20 Pump 2 fault Read-only 1 = Fault
0x15 21 Pump fault, 1 loop Read-only 1 = Fault
0x16 22 Pump fault, 2 loops Read-only 1 = Fault
0x17 23 Heat exchanger inlet sensor fault Read-only 1 = Fault
0x18 24 Heat exchanger outlet sensor fault Read-only 1 = Fault
0x19 25 Outdoor temperature sensor fault Read-only 1 = Fault
0x1a 26 Condenser sensor fault Read-only 1 = Fault
0x1b 27 Manifold outlet sensor fault Read-only 1 = Fault
0x1c 28 Fan fault Read-only 1 = Fault
0x1d 29 EEPROM FAULT Read-only 1 = Fault
0x1e 30 Loop inlet sensor fault (MULTICONNECT) Read-only 1 = Fault
0x1f 31 Loop outlet sensor fault (MULTICONNECT) Read-only 1 = Fault
0x20 32 AEROCONNECT link fault Read-only 1 = Fault
0x21 33 Outdoor temperature too high in cooling mode Read-only 1 = Fault
0x22 34 Change of operating mode fault Read-only 1 = Fault
0x23 35 Winter protection Read-only 1 = Fault
0x24 36 Exchanger ambient sensor fault Read-only 1 = Fault
0x25 to 0x3f reserved
0x40 64 Circuit 1 fault summary Read-only 1 = Fault
0x41 65 Stage 1, circuit 1 fault Read-only 1 = Fault
0x42 66 Stage 2, circuit 1 fault Read-only 1 = Fault
0x43 67 Manual HP fault, circuit 1 Read-only 1 = Fault
0x44 68 HP fault, circuit 1 pressure sensor Read-only 1 = Fault
0x45 69 Circuit 1 LP fault Read-only 1 = Fault
0x46 70 Water frosting fault, circuit 1 Read-only 1 = Fault
0x47 71 Refrigerant frosting fault, circuit 1 Read-only 1 = Fault
0x48 72 Exchanger frosting fault, circuit 1 Read-only 1 = Fault

3/28
 NA 09. 92 B
CONNECT 2
09 - 2010
COMMUNICATION PROTOCOL 3991051.01

Hexadecimal Bit No.

Description Type Setting
bit No. decimal

0x49 73 Discharge fault, stage 1, circuit 1 Read-only 1 = Fault

0x4a 74 Discharge fault, stage 2, circuit 1 Read-only 1 = Fault
0x4b 75 Defrosting fault, circuit 1 Read-only 1 = Fault
0x4c 76 Expansion valve fault, circuit 1 Read-only 1 = Fault
0x4d 77 Stepper motor fault, circuit 1 expansion valve Read-only 1 = Fault
0x4e 78 Low superheat fault, circuit 1 Read-only 1 = Fault
0x4f 79 High superheat fault, circuit 1 Read-only 1 = Fault
0x50 80 VCM module fault, expansion valve 1 Read-only 1 = Fault
0x51 81 Exchanger outlet sensor fault, circuit 1 Read-only 1 = Fault
0x52 82 Exchanger freon sensor fault, circuit 1 Read-only 1 = Fault
0x53 83 Sensor fault, coil A, circuit 1 Read-only 1 = Fault
0x54 84 Sensor fault, coil B, circuit 1 Read-only 1 = Fault
0x55 85 Sensor fault, coil C, circuit 1 Read-only 1 = Fault
0x56 86 Sensor fault, coil D, circuit 1 Read-only 1 = Fault
0x57 87 Discharge sensor fault, stage 1, circuit 1 Read-only 1 = Fault
0x58 88 Discharge sensor fault, stage 2, circuit 1 Read-only 1 = Fault
0x59 89 Circuit 1 HP sensor fault Read-only 1 = Fault
0x5a 90 Circuit 1 LP sensor fault Read-only 1 = Fault
0x5b 91 Circuit 1 suction sensor fault Read-only 1 = Fault
0x5c 92 Circuit 1 liquid sensor fault Read-only 1 = Fault
0x5d 93 Circuit 1 exp. valve board link fault Read-only 1 = Fault
0x5e 94 Link fault, additional board for reversible Read-only 1 = Fault
0x5f 95 Tsat discharge fault, Inverter compressor Read-only 1 = Fault
0x60 96 Mechanical fault, Inverter compressor Read-only 1 = Fault
0x61 to 0x7f reserved
0x80 128 Load shedding, stage 1, circuit 1 Read-only 1 = Load shedding
0x81 129 Load shedding, stage 2, circuit 1 Read-only 1 = Load shedding
0x82 to 0x9f reserved
0x100 256 Circuit 2 fault summary Read-only 1 = Fault
0x101 257 Stage 1, circuit 2 fault Read-only 1 = Fault
0x102 258 Stage 2, circuit 2 fault Read-only 1 = Fault
0x103 259 Manual HP fault, circuit 2 Read-only 1 = Fault
0x104 260 HP fault, circuit 2 pressure sensor Read-only 1 = Fault
0x105 261 Circuit 2 LP fault Read-only 1 = Fault
0x106 262 Water frosting fault, circuit 2 Read-only 1 = Fault
0x107 263 Refrigerant frosting fault, circuit 2 Read-only 1 = Fault
0x108 264 Exchanger frosting fault, circuit 2 Read-only 1 = Fault
0x109 265 Discharge fault, stage 1, circuit 2 Read-only 1 = Fault
0x10a 266 Discharge fault, stage 2, circuit 2 Read-only 1 = Fault
0x10b 267 Defrosting fault, circuit 2 Read-only 1 = Fault
0x10c 268 Expansion valve fault, circuit 2 Read-only 1 = Fault
0x10d 269 Stepper motor fault, circuit 2 expansion valve Read-only 1 = Fault
0x10e 270 Low superheat fault, circuit 2 Read-only 1 = Fault
0x10f 271 High superheat fault, circuit 2 Read-only 1 = Fault
0x110 272 VCM module fault, expansion valve 2 Read-only 1 = Fault
0x111 273 Exchanger outlet sensor fault, circuit 2 Read-only 1 = Fault
0x112 274 Exchanger freon sensor fault, circuit 2 Read-only 1 = Fault

4/28
 NA 09. 92 B
CONNECT 2
09 - 2010
COMMUNICATION PROTOCOL 3991051.01

Hexadecimal Bit No.

Description Type Setting
bit No. decimal

0x113 275 Sensor fault, coil A, circuit 2 Read-only 1 = Fault

0x114 276 Sensor fault, coil B, circuit 2 Read-only 1 = Fault
0x115 277 Sensor fault, coil C, circuit 2 Read-only 1 = Fault
0x116 278 Sensor fault, coil D, circuit 2 Read-only 1 = Fault
0x117 279 Stage 1, circuit 2 discharge sensor fault Read-only 1 = Fault
0x118 280 Stage 2, circuit 2 discharge sensor fault Read-only 1 = Fault
0x119 281 Circuit 2 HP sensor fault Read-only 1 = Fault
0x11a 282 Circuit 2 LP sensor fault Read-only 1 = Fault
0x11b 283 Circuit 2 suction sensor fault Read-only 1 = Fault
0x11c 284 Circuit 2 liquid sensor fault Read-only 1 = Fault
0x11d 285 Circuit 2 exp. valve board link fault Read-only 1 = Fault
0x11e 286 Link fault, additional board for reversible Read-only 1 = Fault
0x11f to 0x13f reserved
0x140 320 Load shedding, stage 1, circuit 2 Read-only 1 = Load shedding
0x141 321 Load shedding, stage 2, circuit 2 Read-only 1 = Load shedding
Read (Functions 1 or 2) and write (Functions 5 or 15) bit
0x200 512 On/Off Read/Write 1 = On
0x201 513 Control set to setpoint 1 or 2 Read/Write 1 = Control set to setpoint 2
0x202 514 Heating or cooling operation Read/Write 1 = Heating
Load shedding via Modbus, stage 1, circuit 1 (different
0x203 515 Read/Write 1 = Off
from 0 x 140)
0x204 516 Load shedding via Modbus, stage 2, circuit 1 Read/Write 1 = Off
0x205 517 Load shedding via Modbus, stage 1, circuit 2 Read/Write 1 = Off
0x206 518 Load shedding via Modbus, stage 2, circuit 2 Read/Write 1 = Off

5/28
 NA 09. 92 B
CONNECT 2
09 - 2010
COMMUNICATION PROTOCOL 3991051.01

CONFIGURATION PARAMETERS

Hexadecimal Decimal
Description Format Type Setting
bit number bit numbe

Registers accessible in read mode (functions 3 or 4) and write mode (functions 6 for 'Char' or 16)
Configuration parameters
0x1000 4096 P99 Lock Char Read/Write 0 or 1
0: R407c
0x1001 4097 P01 Refrigerant type Char Read/Write 1: 134a
2: 404a
1: Water-to-water unit
0x1002 4098 P02 Unit type Char Read/Write 2: Air-to-water unit
3: Reversible air-to-water unit
0x1003 4099 P03 Number of circuits Char Read/Write 1 or 2
0x1004 4100 P04 Number of stages on circuit 1 Char Read/Write 1 or 2
0x1005 4101 P05 Number of stages on circuit 2 Char Read/Write 1 or 2
0x1006 4102 P06 Number of evaporators Char Read/Write 1 or 2
0: Maneurop
0x1007 4103 P07 Compressor supplier Char Read/Write 1: Copeland
2: inverter
0: Propeller
0x1008 4104 P10 Fan type Char Read/Write 1: Centrifugal
2: Pressure
0: Intertwined
0x1009 4105 P11 Coil type Char Read/Write 1: Split
2: Mixed
0x100A 4106 P12 Pressure balancing valve Char Read/Write 0 or 1
0x100B 4107 P13 Balanced tandem compressors Char Read/Write 0 or 1
0x100C 4108 P14 Number of coil sensors per circuit Char Read/Write 1 to 4
0x100D 4109 P20 All-season function Char Read/Write 0 or 1
0: No control
0x100E 4110 P21 Speed control Char Read/Write 1: Acoustic optimisation
2: Energy optimisation
0x100F 4111 P22 Presence of electric auxiliary heaters Char Read/Write 0 or 1
0x1010 4112 P25 Number of pumps supplied by CIAT Char Read/Write 0 to 2
0x1011 4113 P26 0-10 V programmable output Char Read/Write 0: Two-way valve
1: Three-way valve
0x1012 4114 P27 Pump controlled by boiler Char Read/Write 0 or 1
0x1013 4115 P28 Master/Slave (2 machines) Char Read/Write 0 or 1
0x1014 4116 P29 Total recovery Char Read/Write 0 or 1
0x1015 4117 P29. 1 Recovery exchanger frost protection Char Read/Write 0 or 1
0x1016 & 0x1017 4118 & 4119 P30 HP1 sensor high value float Read/Write
0x1018 & 0x1019 4120 & 4121 P31 HP1 sensor low value float Read/Write
0x101a & 0x101b 4122 & 4123 P32 HP2 sensor high value float Read/Write
0x101c & 0x101d 4124 & 4125 P33 HP2 sensor low value float Read/Write
0x101e & 0x101f 4126 & 4127 P36 LP1 sensor high value float Read/Write
0x1020 & 0x1021 4128 & 4129 P37 LP1 sensor low value float Read/Write
0x1022 & 0x1023 4130 & 4131 P38 LP2 sensor high value float Read/Write
0x1024 & 0x1025 4132 & 4133 P39 LP2 sensor low value float Read/Write
0: None
0x1026 4134 P42 Electronic expansion valve driver Char Read/Write 1: Alco driver
2: CIAT driver

6/28
 NA 09. 92 B
CONNECT 2
09 - 2010
COMMUNICATION PROTOCOL 3991051.01

Hexadecimal Decimal
Description Format Type Setting
bit number bit numbe

0x1027 4135 P43 Superheat protection Char Read/Write 0 or 1

0x1028 & 0x1029 4136 & 4137 P44 Superheat minimum limit float Read/Write
0x102a & 0x102b 4138 & 4139 P45 Superheat maximum limit float Read/Write
0x102c 4140 P50 Compressor short-cycle protection Char Read/Write
0x102d 4141 P51 Discharge temperature limit Char Read/Write
0x102e & 0x102f 4142 & 4143 P52 Water frost limit float Read/Write
0x1030 & 0x1031 4144 & 4145 P53 Δ for refrigerant frost protection limit/P52 float Read/Write
0x1032 & 0x1033 4146 & 4147 P54 HP fault threshold float Read/Write
0x1034 & 0x1035 4148 & 4149 P55 LP fault threshold float Read/Write
0x1036 & 0x1037 4150 & 4151 P58 LP slope factor float Read/Write
0x1038 & 0x1039 4152 & 4153 P59 Water outlet temperature slope factor float Read/Write
0x103a & 0x103b 4154 & 4155 P63 Min. HP fault threshold float Read/Write
unsigned
0x103c 4156 P66 inverter compressor start time short Read/Write
integer
Configuration parameters for electronic expansion valve
0: EX4 valve
1: EX5 valve
0x103d 4157 P601 Circuit 1 valve type Char Read/Write 2: EX6 valve
3: EX7 valve
4: EX8 valve
0x103e & 0x103f 4158 & 4159 P602 Circuit 1 superheat setpoint float Read/Write
0x1040 4160 P603 Circuit 1 MOP value Char Read/Write 0 or 1
0x1041 4161 P604 Circuit 1 MOP value Char Read/Write

0x1042 4162 P605 Valve opening at AC mode start, circuit 1 Char Read/Write

P606 Valve opening at heat pump mode start,

0x1043 4163 Char Read/Write
circuit 1
0x1044 4164 P607 Open time at start, circuit 1 Char Read/Write
0x1045 4165 P608 Circuit 1 expansion valve slow mode Char Read/Write 0 or 1
0: EX4 valve
1: EX5 valve
0x1046 4166 P611 Circuit 2 valve type Char Read/Write 2: EX6 valve
3: EX7 valve
4: EX8 valve
0x1047 & 0x1048 4167 & 4168 P612 Circuit 2 superheat setpoint float Read/Write
0x1049 4169 P613 Circuit 2 MOP value Char Read/Write 0 or 1
0x104a 4170 P614 Circuit 2 MOP value Char Read/Write

0x104b 4171 P615 Valve opening at AC mode start, circuit 1 Char Read/Write

P616 Valve opening at heat pump mode start,

0x104c 4172 Char Read/Write
circuit 1
0x104d 4173 P617 Open time at start, circuit 2 Char Read/Write
0x104e 4174 P618 Circuit 1 expansion valve slow mode Char Read/Write 0 or 1

7/28
 NA 09. 92 B
CONNECT 2
09 - 2010
COMMUNICATION PROTOCOL 3991051.01

ADJUSTMENT PARAMETERS

Hexadecimal Decimal
Description Format Type Setting
bit number bit numbe

Registers accessible in read mode (functions 3 or 4) and write mode (functions 6 for 'Char' or 16)
0: French
1: English
2: German
0x1200 4608 P100 Local console language Char Read-only 3: Spanish
4: Dutch
5: Italian
6: Russian
0: As a function of On/Off
0x1201 4609 P108 Pump 2 control Char Read/Write
1: As a function of the control mode
0x1202 4610 P109 Pump 2 time delay Char Read/Write
0: Max. power
0x1203 4611 P111 Programmable output Char Read/Write 1: Boiler output
2: Cooling/heating output
0x1204 4612 P112 Number of electric stages Char Read/Write
0: Disabled
1: Load shedding of electric
0x1205 4613 P113 Programmable input Char Read/Write
auxiliary heaters
2: Electric auxiliary heaters forced on
0x1206 4614 P116 Link with Aeroconnect Char Read/Write 0 or 1
0: Cooling only
1: Heating only
2: Cooling/heating via console
0x1207 4615 P119 Operating mode Char Read/Write
or BMS
3: Cooling/heating via on/off input
4: Automatic cooling/heating
1: 1 setpoint
2: 2 setpoints via console or
0x1208 4616 P120 Number of setpoints Char Read/Write BMS
3: 2 setpoints via On/Off input
4: setpoint via 4-20 mA input
0x1208 to 0x1218 reserved
P127 Cooling controlled as a function of the
0x1219 4633 Char Read/Write 0 or 1
outdoor temperature
0x121a & 0x121b 4634 & 4635 P128 Drift start in cooling mode Float Read/Write
0x121c & 0x121d 4636 & 4637 P129 Drift end in cooling mode Float Read/Write
0x121e & 0x121f 4638 & 4639 P130 Cooling setpoint at end of drift Float Read/Write
P131 Heating controlled as a function of the
0x1220 4640 Char Read/Write 0 or 1
outdoor temperature
0x1221 & 0x1222 4641 & 4642 P132 Drift start in heating mode Float Read/Write
0x1223 & 0x1224 4643 & 4644 P133 Drift end in heating mode Float Read/Write
0x1225 & 0x1226 4645 & 4646 P134 Heating setpoint at end of drift Float Read/Write
0x1227 & 0x1228 4647 & 4648 P135 Minimum boiler setpoint Float Read/Write
0x1129 & 0x122a 4949 & 4650 P136 Max. outdoor temp. in auto heating mode Float Read/Write
0x122b & 0x122c 4651 & 4652 P137 Min. outdoor temp. in auto cooling mode Float Read/Write

8/28
 NA 09. 92 B
CONNECT 2
09 - 2010
COMMUNICATION PROTOCOL 3991051.01

Hexadecimal Decimal
Description Format Type Setting
bit number bit numbe

0x122d to 0x123f reserved

1: Return
0x1240 4672 P141 Control mode Char Read/Write 2: Supply
3: Outlet with compensation
0x1241 4673 P142 Water loop winter protection Char Read/Write 0 or 1
0x1242 & 0x1243 4674 & 4675 P143 Stage differential Float Read/Write
0x1244 & 0x1245 4676 & 4677 P144 Interstage differential Float Read/Write
0x1246 & 0x1247 4678 & 4679 P145 P coefficient Float Read/Write
0x1248 & 0x1249 4680 & 4681 P146 I coefficient Float Read/Write
0x124a & 0x124b 4682 & 4683 P147 D coefficient Float Read/Write
0x124c 4684 P148 T coefficient Char Read/Write
0x124d & 0x124e 4685 & 4686 P150 Compensation coefficient Float Read/Write
0x124f 4687 P151 Compensation time Char Read/Write
0x1250 4688 P154 Storage control Char Read/Write 0 or 1
0x1251 & 0x1252 4689 & 4690 P155 Delta T for storage control Float Read/Write
0x1253 & 0x1254 4691 & 4692 P157 Frosting start temperature Float Read/Write
0x1255 & 0x1256 4693 & 4694 P158 Defrosting end temperature Float Read/Write
1: Fixed time
0x1257 4695 P159 Frosting type Char Read/Write
2: Optimised
0x1258 4696 P160 Fixed frosting time Char Read/Write
0x1259 & 0x125a 4697 & 4698 P161 Frosting factor Float Read/Write
0x125b & 0x125c 4699 & 4700 P162 Reference outdoor temperature correction Float Read/Write
0x125d 4701 P163 Compressor 'Off' time delay during defrost Usi Read/Write
0x125e & 0x125f 4702 & 4703 P164 HP 'On' differential during defrosting Float Read/Write
0x1260 & 0x1261 4704 & 4705 P165 HP 'Off' differential during defrosting Float Read/Write
0x1262 to 0x126f reserved
0x1270 & 0x1271 4720 & 4721 P171 Charge limit temperature Float Read/Write
0: Automatic
0x1272 4722 P175 Load shedding mode Char Read/Write
1: Selective
0x1273 to 0x127a reserved
0x127b 4731 P180 Number of fan stages Char Read/Write
0x127c & 0x127d 4732 & 4733 P181 HP control setpoint Float Read/Write
0x127e & 0x127f 4734 & 4735 P183 HP control stage differential Float Read/Write
0x1280 & 0x1281 4736 & 4737 P184 HP control interstage differential Float Read/Write
0x1282 to 0x128f reserved
0x1290 4752 P191 Low Noise operation Char Read/Write 0 or 1
0x1291 & 0x1292 4753 & 4754 P192 Maximum fan speed Float Read/Write
0x1293 & 0x1294 4755 & 4756 P193 HP control setpoint in recovery mode Float Read/Write
0x1295 & 0x1296 4757 & 4758 P195 Delta P for power reduction Float Read/Write
0x1297 & 0x1298 4759 & 4760 P196 Return ΔP normal condensing control Float Read/Write
0x1299 & 0x129a 4761 & 4762 P197 Value at 0 V; 0-10 V output linked to P26 Float Read/Write
0x129b & 0x129c 4763 & 4764 P198 Value at 10 V; 0-10 V output linked to P26 Float Read/Write

9/28
 NA 09. 92 B
CONNECT 2
09 - 2010
COMMUNICATION PROTOCOL 3991051.01

Hexadecimal Decimal
Description Format Type Setting
bit number bit number

0x129d to 0x12aa reserved

0x12ab & 0x12ac 4779 & 4780 P220 Winter protection outdoor temperature Float Read/Write
0x12ad & 0x12ae 4781 & 4782 P222 Winter protection differential Float Read/Write
0x12af & 0x12b0 4783 & 4784 P225 Min. outdoor temperature in heating mode Float Read/Write 0=Disabled
0x12b1 & 0x12b2 4785 & 4786 P225.1 Max. outdoor temp. in cooling mode Float Read/Write
0x12b3 & 0x12b4 4787 & 4788 P226 Min. outdoor temp. for turning on auxiliaries Float Read/Write
0x12b5 4789 P230 Stage 1, circuit 1 'On' authorisation Char Read/Write 0 or 1
0x12b6 4790 P231 Stage 2, circuit 1 'On' authorisation Char Read/Write 0 or 1
0x12b7 4791 Reserved
0x12b8 4792 P232 Stage 1, circuit 2 'On' authorisation Char Read/Write 0 or 1
0x12b9 4793 P233 Stage 2, circuit 2 'On' authorisation Char Read/Write 0 or 1
0x12ba 4794 Reserved
0x12bb 4795 P235 Electric stage 1 'On' authorisation Char Read/Write 0 or 1
0x12bc 4796 P236 Electric stage 2 'On' authorisation Char Read/Write 0 or 1
0x12bd 4797 P237 Electric stage 3 'On' authorisation Char Read/Write 0 or 1
0x12be 4798 P238 Electric stage 4 'On' authorisation Char Read/Write 0 or 1
0x12bf & 0x12c0 4799 & 4800 Circuit 1 HP sensor adjustment Float Read/Write
0x12c1 & 0x12c2 4801 & 4802 Circuit 1 LP sensor adjustment Float Read/Write
0x12c3 & 0x12c4 4803 & 4804 Circuit 2 HP sensor adjustment Float Read/Write
0x12c5 & 0x12c6 4805 & 4806 Circuit 2 LP sensor adjustment Float Read/Write
0x12c7 & 0x12cf reserved
0x12d0 4816 Order number, digit 1 Char Read/Write 0 to 9
0x12d1 4817 Order number, digit 2 Char Read/Write 0 to 9
0x12d2 4818 Order number, digit 3 Char Read/Write 0 to 9
0x12d3 4819 Order number, digit 4 Char Read/Write 0 to 9
0x12d4 4820 Order number, digit 5 Char Read/Write 0 to 9
0x12d5 4821 Order number, digit 6 Char Read/Write 0 to 9
0x12d6 4822 Order number, digit 7 Char Read/Write 0 to 9
0x12d7 4823 Order number, digit 8 Char Read/Write 0 to 9
0x12d8 4824 SN, digit 1 Char Read/Write 0 to 9
0x12d9 4825 SN, digit 2 Char Read/Write 0 to 9
0x12da 4826 SN, digit 3 Char Read/Write 0 to 9
0x12db 4827 SN, digit 4 Char Read/Write 0 to 9
0x12dc 4828 SN, digit 5 Char Read/Write 0 to 9
0x12dd 4829 SN, digit 6 Char Read/Write 0 to 9
0x12de 4830 SN, digit 7 Char Read/Write 0 to 9
0x12df 4831 SN, digit 8 Char Read/Write 0 to 9

10/28
 NA 09. 92 B
CONNECT 2
09 - 2010
COMMUNICATION PROTOCOL 3991051.01

OPERATION PARAMETER

Hexadecimal Decimal
Description Format Type Setting
bit number bit number

Registers accessible in read-only mode (functions 3 or 4)

0x1500 & 0x1501 5376 & 5377 P255 Exchanger 1 water inlet temperature Float Read-only
0x1502 & 0x1503 5378 & 5379 P256 Exchanger 1 water outlet temperature Float Read-only
0x1504 & 0x1505 5380 & 5381 P257 or P258 condenser temperature Float Read-only
0x1506 & 0x1507 5382 & 5383 P259.A Coil A circuit 1 temperature Float Read-only
0x1508 & 0x1509 5384 & 5385 P259.B Coil B circuit 1 temperature Float Read-only
0x150a & 0x150b 5386 & 5387 P259.C Coil C circuit 1 temperature Float Read-only
0x150c & 0x150d 5388 & 5389 P259.D Coil D circuit 1 temperature Float Read-only
0x150e & 0x150f 5390 & 5391 P260 Circuit 1 refrigerant temperature Float Read-only
0x1510 & 0x1511 5392 & 5393 P261 Manifold water outlet temperature Float Read-only
0x1512 & 0x1513 5394 & 5395 P262 Exchanger 2 water outlet temperature Float Read-only
0x1514 & 0x1515 5396 & 5397 P263.A Circuit 2 coil A temperature Float Read-only
0x1516 & 0x1517 5398 & 5399 P263.B Circuit 2 coil B temperature Float Read-only
0x1518 & 0x1519 5400 & 5401 P263.C Circuit 2 coil C temperature Float Read-only
0x151a & 0x151b 5402 & 5403 P263.D Circuit 2 coil D temperature Float Read-only
0x151c & 0x151d 5404 & 5405 P264 Circuit 2 refrigerant temperature Float Read-only
0x151e & 0x151f 5406 & 5407 P265 Exchanger ambient temperature Float Read-only
0x1520 5408 P266 Circuit 1 frosting time Char Read-only
0x1521 5409 P267 Circuit 2 frosting time Char Read-only
0x1522 5410 P270 Controller action time delay Char Read-only
0x1523 5411 P271 Calculated frosting time Char Read-only
0x1524 à 0x152f Reserved
0x1530 & 0x1531 5424 & 5425 P289 Number of times P99 set to 'no' Float Read-only
0x1532 5126 P290 Number of water flow cuts in one hour Char Read-only
0x1533 & 0x153f reserved
0x1540 & 0x1541 5440 & 5441 P300 Circuit 1 HP Float Read-only
0x1542 & 0x1543 5442 & 5443 P300.1 Circuit 1 HP control setpoint Float Read-only
0x1544 & 0x1545 5444 & 5445 P301 Circuit 1 condensing temperature Float Read-only
0x1546 & 0x1547 5446 & 5447 P302.1 Compressor 1 discharge temperature Float Read-only
0x1548 & 0x1549 5448 & 5449 P302.2 Compressor 2 discharge temperature Float Read-only
0x154a & 0x154b 5450 & 5451 P303.1 Compressor 1 disch. desuperheating Float Read-only
0x154c & 0x154d 5452 & 5453 P303.2 Compressor 2 disch. desuperheating Float Read-only
0x154e & 0x154f 5454 & 5455 P304 Circuit 1 LP Float Read-only
0x1550 & 0x1551 5456 & 5457 P305 Circuit 1 evaporating temperature Float Read-only
0x1552 & 0x1553 5458 & 5459 P306 Circuit 1 suction temperature Float Read-only
0x1554 & 0x1555 5460 & 5461 P307 Circuit 1 superheat Float Read-only
0x1556 5462 P308 No. of HP cuts on circuit 1 in 24 hours Char Read-only
0x1557 5463 P309 Number of LP cuts on circuit 1 in 24 hours Char Read-only
0x1558 5464 P312 Compressor 1 short-cycle protection integer Read-only
0x1559 5465 P313 Compressor 2 short-cycle protection integer Read-only
0x155a 5466 P322 Number of frost/water cuts on circuit 1 Char Read-only
0x155b 5467 P323 No. of frost/refrigerant cuts on circuit 1 Char Read-only

11/28
 NA 09. 92 B
CONNECT 2
09 - 2010
COMMUNICATION PROTOCOL 3991051.01

Hexadecimal Decimal
Description Format Type Setting
bit number bit number

0x155c 5468 P324.1 Number of C1 disch. cuts in 24 hours Char Read-only

0x155d 5469 P324.2 Number of C2 disch. cuts in 24 hours Char Read-only
0x155e & 0x155f 5470 & 5471 P325 Circuit 1 expansion valve opening % Float Read-only
0x1560 & 0x1561 5472 & 5473 P326 Circuit 1 liquid temperature Float Read-only
0x1562 & 0x1563 5474 & 5475 P327 Circuit 1 subcooling Float Read-only
0x1564 & 0x156f reserved
0x1570 & 0x1571 5488 & 5489 P330 Circuit 2 HP Float Read-only
0x1572 & 0x1573 5490 & 5491 P330.1 Circuit 2 HP control setpoint Float Read-only
0x1574 & 0x1575 5492 & 5493 P331 Circuit 2 condensing temperature Float Read-only
0x1576 & 0x1577 5494 & 5495 P332.1 Compressor 3 discharge temperature Float Read-only
0x1578 & 0x1579 5496 & 5497 P332.2 Compressor 4 discharge temperature Float Read-only
0x157a & 0x157b 5498 & 5499 P333.1 Compressor 3 disch. desuperheating Float Read-only
0x157c & 0x157d 5500 & 5501 P333.2 Compressor 4 disch. desuperheating Float Read-only
0x157e & 0x157f 5502 & 5503 P334 Circuit 2 LP Float Read-only
0x1580 & 0x1581 5504 & 5505 P335 Circuit 2 evaporating temperature Float Read-only
0x1582 & 0x1583 5506 & 5507 P336 Circuit 2 suction temperature Float Read-only
0x1584 & 0x1585 5508 & 5509 P337 Circuit 2 superheat Float Read-only 0x1584 & 0x1585
0x1586 5510 P338 Number of HP cuts on circ. 2 in 24 hours Char Read-only 0x1586
0x1587 5511 P339 Number of LP cuts on circ. 2 in 24 hours Char Read-only 0x1587
0x1588 5512 P342 Compressor 3 short-cycle protection Char Read-only 0x1588
0x1589 5513 P343 Compressor 4 short-cycle protection Char Read-only 0x1589
0x158a 5514 P352 Number of frost/water cuts on circuit 2 Char Read-only 0x158a
0x158b 5515 P353 Number of frost/refrigerant cuts on circ. 2 Char Read-only 0x158b
0x158c 5516 P354.1 Number of C3 disch. cuts in 24 hours Char Read-only 0x158c
0x158d 5517 P354.2 Number of C4 disch. cuts in 24 hours Char Read-only 0x158d
0x158e & 0x158f 5518 & 5519 P355 Circuit 2 expansion valve opening % Float Read-only 0x158e & 0x158f
0x1590 & 0x1591 5520 & 5521 P356 Circuit 2 liquid temperature Float Read-only 0x1590 & 0x1591
0x1592 & 0x1593 5522 & 5523 P357 Circuit 2 subcooling Float Read-only
0x1594 & 0x159f reserved
Bits 0 to 7: Edition; Bits 8 to
0x15a0 5536 P555 CPU software version number Char Read-only
15: Version
0x15a1 5537 P557 Circuit 2 board software version number Char Read-only
0x15a2 5538 P558 Circuit 1 EXV board software version number Char Read-only
0x15a3 5539 P558 Circuit 1 VCM module software version number Char Read-only
0x15a4 5540 P559 Circuit 2 EXV board software version number Char Read-only
0x15a5 5541 P559 Circuit 2 VCM module software version number Char Read-only

12/28
 NA 09. 92 B
CONNECT 2
09 - 2010
COMMUNICATION PROTOCOL 3991051.01

CUSTOMER ACCESS BITS

Hexadecimal Decimal
Description Type Setting
bit number bit number

Read-only bit (functions 1 or 2)

Input state zone
0x1000 4096 P400 Electric auxiliary board input state Read-only 0=Open
0x1001 4097 P402 Setpoint 1/2 input state Read-only 0=Open
0x1002 4098 P403 Water flow input state Read-only 0=Open
0x1003 4099 P404 Fan fault input state Read-only 0=Open
0x1004 4100 P405 Heating/cooling input state Read-only 0=Open
0x1005 4101 P406 Phase controller input state Read-only 0=Open
0x1006 4102 P407 Total recovery input state Read-only 0=Open
0x1007 4103 P408 State of input 1 on elec. aux. heater board Read-only 0=Open
0x1008 4104 P409 State of input 2 on elec. aux. heater board Read-only 0=Open
0x1009 4105 P410 State of load shedding input on auxiliary heater board Read-only 0=Open
0x100a 4106 P414 State of stage 1, circuit 1 load shed. input Read-only 0=Open
0x100b 4107 P415 State of stage 2, circuit 1 load shed. input Read-only 0=Open
0x100c 4108 P416 State of stage 1, circuit 2 load shed. input Read-only 0=Open
0x100d 4109 P417 State of stage 2, circuit 2 load shed. input Read-only 0=Open
0x100e 4110 P418 State of circuit 1 manual HP input Read-only 0=Open
0x100f 4111 P419 State of stage 1, circuit 1 motor fault input Read-only 0=Open
0x1010 4112 P420 State of stage 2, circuit 1 motor fault input Read-only 0=Open
0x1011 4113 P422 State of circuit 2 manual HP input Read-only 0=Open
0x1012 4114 P423 State of stage 1, circuit 2 motor fault input Read-only 0=Open
0x1013 4115 P424 State of stage 2, circuit 2 motor fault input Read-only 0=Open
0x1014 4116 P425 State of circuit 1 EXV fault input Read-only 0=Open
0x1015 4117 P426 State of circuit 2 EXV fault input Read-only 0=Open
0x1016 4118 State of pump 1 fault input Read-only 0=Open
0x1017 4119 State of pump 2 fault input Read-only 0=Open
Output state zone
0x1050 4176 P432 State of circuit 1 four-way valve output Read-only 0=Off
0x1051 4177 P433 State of circuit 2 four-way valve output Read-only 0=Off
0x1052 4178 P435 Heat trace cable state Read-only 0=Off
0x1053 4179 P436 Heater output state Read-only 0=Off
0x1054 4180 P437 State of desuperheater heater output Read-only 0=Off
0x1055 4181 P438 State of maximum power output Read-only 0=Off
0x1056 4182 P441 State of stage 1, circuit 1 fan output Read-only 0=Off
0x1057 4183 P442 State of stage 2, circuit 1 fan output Read-only 0=Off
0x1058 4184 P445 State of stage 3, circuit 1 fan output Read-only 0=Off
0x1059 4185 P443 State of stage 1, circuit 2 fan output Read-only 0=Off
0x105a 4186 P444 State of stage 2, circuit 2 fan output Read-only 0=Off
0x105b 4187 P446 State of stage 3, circuit 2 fan output Read-only 0=Off
0x105c 4188 P451 State of circuit 1 balancing valve Read-only 0=Off
0x105d 4189 P452 State of circuit 2 balancing valve Read-only 0=Off
Limiter state area
0x1100 4352 Charge limit (water temp. > P171 in cooling mode) Read-only 1=Limit on
0x1101 4353 Circuit 1 water frost limit Read-only 1=Limit on
0x1102 4354 Circuit 1 refrigerant frost limit Read-only 1=Limit on
0x1103 4355 Circuit 1 minimum HP limit Read-only 1=Limit on
0x1104 4356 Circuit 1 maximum HP limit Read-only 1=Limit on

13/28
 NA 09. 92 B
CONNECT 2
09 - 2010
COMMUNICATION PROTOCOL 3991051.01

Hexadecimal Decimal
Description Type Setting
bit number bit number

0x1105 4357 Stage 1, circuit 1 discharge limit Read-only 1=Limit on

0x1106 4358 Stage 2, circuit 1 discharge limit Read-only 1=Limit on
0x1107 4359 NU
0x1108 4360 Circuit 2 water frost limit Read-only 1=Limit on
0x1109 4361 Circuit 2 refrigerant frost limit Read-only 1=Limit on
0x110a 4362 Circuit 2 minimum HP limit Read-only 1=Limit on
0x110b 4363 Circuit 2 maximum HP limit Read-only 1=Limit on
0x110c 4364 Stage 1, circuit 2 discharge limit Read-only 1=Limit on
0x110d 4365 Stage 2, circuit 2 discharge limit Read-only 1=Limit on
0x110e 4366 Discharge limit in heating mode (setpoint drop) Read-only 1=Limit on

FAULT MEMORY

Hexadecimal Decimal
Description Format Type Setting
bit number bit number

Registers accessible in read-only mode (functions 3 or 4)

Fault memory area 1
unsigned
0x2000 8192 Fault number in fault memory Read-only
inIt
0x2001 8193 Fault memory year Char Read-only
0x2002 8194 Fault memory month Char Read-only
0x2003 8195 Fault memory day of month Char Read-only
0x2004 8196 Fault memory hour Char Read-only
0x2005 8197 Fault memory minutes Char Read-only
0x2006 & 0x2007 8198 & 8199 Fault memory HP Float Read-only
0x2008 & 0x2009 8200 & 8201 Fault memory condensing temperature Float Read-only
0x200a & 0x200b 8202 & 8203 Fault memory LP Float Read-only
0x200c & 0x200d 8204 & 8205 Fault memory evaporating temperature Float Read-only
0x200e & 0x200f 8206 & 8207 Fault memory suction temperature Float Read-only
0x2010 & 0x2011 8208 & 8209 Fault memory superheat Float Read-only
0x2012 8210 Stage 1 circuit x discharge Char Read-only
0x2013 8211 Stage 2 circuit x discharge Char Read-only
0x2014 & 0x2015 8212 & 8213 Outdoor temperature Float Read-only
0x2016 & 0x2017 8214 & 8215 Control setpoint Float Read-only
0x2018 & 0x2019 8216 & 8217 Water inlet temperature Float Read-only
0x201a & 0x201b 8218 & 8219 Circuit x water outlet temperature Float Read-only
0x201c & 0x201d 8220 & 8221 Hot water temperature Float Read-only
0x201e & 0x201f 8222 & 8223 Refrigerant temperature Float Read-only
Fault memory area 2
Unsigned
0x2060 8288 Fault number in fault memory Read-only
int
0x2061 8289 Fault memory year Char Read-only
0x2062 8290 Fault memory month Char Read-only
0x2063 8291 Fault memory day of month Char Read-only
0x2064 8292 Fault memory hour Char Read-only
0x2065 8293 Fault memory minutes Char Read-only
0x2066 & 0x2067 8294 & 8295 Fault memory HP Float Read-only

14/28
 NA 09. 92 B
CONNECT 2
09 - 2010
COMMUNICATION PROTOCOL 3991051.01

Hexadecimal Decimal
Description Format Type Setting
bit number bit number

0x2068 & 0x2069 8296 & 8297 Fault memory condensing temperature Float Read-only
0x206a & 0x206b 8298 & 8299 Fault memory LP Float Read-only
0x206c & 0x206d 8300 & 8301 Fault memory evaporating temperature Float Read-only
0x206e & 0x206f 8302 & 8303 Fault memory suction temperature Float Read-only
0x2070 & 0x2071 8304 & 8305 Fault memory superheat Float Read-only
0x2072 8306 Stage 1 circuit x discharge Char Read-only
0x2073 8307 Stage 2 circuit x discharge Char Read-only
0x2074 & 0x2075 8308 & 8309 Outdoor temperature Float Read-only
0x2076 & 0x2077 8310 & 8311 Control setpoint Float Read-only
0x2078 & 0x2079 8312 & 8313 Water inlet temperature Float Read-only
0x207a & 0x207b 8314 & 8315 Circuit x water outlet temperature Float Read-only
0x207c & 0x207d 8316 & 8317 Hot water temperature Float Read-only
0x207e & 0x207f 8318 & 8319 Refrigerant temperature Float Read-only
Fault memory area 3
Unsigned
0x20c0 8384 Fault number in fault memory Read-only
int
0x20c1 8385 Fault memory year Char Read-only
0x20c2 8386 Fault memory month Char Read-only
0x20c3 8387 Fault memory day of month Char Read-only
0x20c4 8388 Fault memory hour Char Read-only
0x20c5 8389 Fault memory minutes Char Read-only
0x20c6 & 0x20c7 8390 & 8391 Fault memory HP Float Read-only
0x20c8 & 0x20c9 8392 & 8393 Fault memory condensing temperature Float Read-only
0x20ca & 0x20cb 8394 & 8395 Fault memory LP Float Read-only
0x20cc & 0x20cd 8396 & 8397 Fault memory evaporating temperature Float Read-only
0x20ce & 0x20cf 8398 & 8399 Fault memory suction temperature Float Read-only
0x20d0 & 0x20d1 8400 & 8401 Fault memory superheat Float Read-only
0x20d2 8402 Stage 1 circuit x discharge Char Read-only
0x20d3 8403 Stage 2 circuit x discharge Char Read-only
0x20d4 & 0x20d5 8404 & 8405 Outdoor temperature Float Read-only
0x20d6 & 0x20d7 8406 & 8407 Control setpoint Float Read-only
0x20d8 & 0x20d9 8408 & 8409 Water inlet temperature Float Read-only
0x20da & 0x20db 8410 & 8411 Circuit x water outlet temperature Float Read-only
0x20dc & 0x20dd 8412 & 8413 Hot water temperature Float Read-only
0x20de & 0x20df 8414 & 8415 Refrigerant temperature Float Read-only
Fault memory area 4
Unsigned
0x2120 8480 Fault number in fault memory Read-only
int
0x2121 8481 Fault memory year Char Read-only
0x2122 8482 Fault memory month Char Read-only
0x2123 8483 Fault memory day of month Char Read-only
0x2124 8484 Fault memory hour Char Read-only
0x2125 8485 Fault memory minutes Char Read-only
0x2126 & 0x2127 8486 & 8487 Fault memory HP Float Read-only
0x2128 & 0x2129 8488 & 8489 Fault memory condensing temperature Float Read-only
0x212a & 0x212b 8490 & 8491 Fault memory LP Float Read-only
0x212c & 0x212d 8492 & 8493 Fault memory evaporating temperature Float Read-only
0x212e & 0x212f 8494 & 8495 Fault memory suction temperature Float Read-only
0x2130 & 0x2131 8496 & 8497 Fault memory superheat Float Read-only

15/28
 NA 09. 92 B
CONNECT 2
09 - 2010
COMMUNICATION PROTOCOL 3991051.01

Hexadecimal Decimal
Description Format Type Setting
bit number bit number

0x2132 8498 Stage 1 circuit x discharge Char Read-only

0x2133 8499 Stage 2 circuit x discharge Char Read-only
0x2134 & 0x2135 8500 & 8501 Outdoor temperature Float Read-only
0x2136 & 0x2137 8502 & 8503 Control setpoint Float Read-only
0x2138 & 0x2139 8504 & 8505 Water inlet temperature Float Read-only
0x213a & 0x213b 8506 & 8507 Circuit x water outlet temperature Float Read-only
0x213c & 0x213d 8508 & 8509 Hot water temperature Float Read-only
0x213e & 0x213f 8510 & 8511 Refrigerant temperature Float Read-only
Fault memory area 5
Unsigned
0x2180 8576 Fault number in fault memory Read-only
int
0x2181 8577 Fault memory year Char Read-only
0x2182 8578 Fault memory month Char Read-only
0x2183 8579 Fault memory day of month Char Read-only
0x2184 8580 Fault memory hour Char Read-only
0x2185 8581 Fault memory minutes Char Read-only
0x2186 & 0x2187 8582 & 8583 Fault memory HP Float Read-only
0x2188 & 0x2189 8584 & 8585 Fault memory condensing temperature Float Read-only
0x218a & 0x218b 8586 & 8587 Fault memory LP Float Read-only
0x218c & 0x218d 8588 & 8589 Fault memory evaporating temperature Float Read-only
0x218e & 0x218f 8590 & 8591 Fault memory suction temperature Float Read-only
0x2190 & 0x2191 8592 & 8593 Fault memory superheat Float Read-only
0x2192 8594 Stage 1 circuit x discharge Char Read-only
0x2193 8595 Stage 2 circuit x discharge Char Read-only
0x2194 & 0x2195 8596 & 8597 Outdoor temperature Float Read-only
0x2196 & 0x2197 8598 & 8599 Control setpoint Float Read-only
0x2198 & 0x2199 8600 & 8601 Water inlet temperature Float Read-only
0x219a & 0x219b 8602 & 8603 Circuit x water outlet temperature Float Read-only
0x219c & 0x219d 8604 & 8605 Hot water temperature Float Read-only
0x219e & 0x219f 8606 & 8607 Refrigerant temperature Float Read-only
Fault memory area 6
Unsigned
0x21e0 8672 Fault number in fault memory Read-only
int
0x21e1 8673 Fault memory year Char Read-only
0x21e2 8674 Fault memory month Char Read-only
0x21e3 8675 Fault memory day of month Char Read-only
0x21e4 8676 Fault memory hour Char Read-only
0x21e5 8677 Fault memory minutes Char Read-only
0x21e6 & 0x21e7 8678 & 8679 Fault memory HP Float Read-only
0x21e8 & 0x21e9 8680 & 8681 Fault memory condensing temperature Float Read-only
0x21ea & 0x21eb 8682 & 8683 Fault memory LP Float Read-only
0x21ec & 0x21ed 8684 & 8685 Fault memory evaporating temperature Float Read-only
0x21ee & 0x21ef 8686 & 8687 Fault memory suction temperature Float Read-only
0x21f0 & 0x21f1 8688 & 8689 Fault memory superheat Float Read-only
0x21f2 8690 Stage 1 circuit x discharge Char Read-only
0x21f3 8691 Stage 2 circuit x discharge Char Read-only
0x21f4 & 0x21f5 8692 & 8693 Outdoor temperature Float Read-only
0x21f6 & 0x21f7 8694 & 8695 Control setpoint Float Read-only
0x21f8 & 0x21f9 8696 & 8697 Water inlet temperature Float Read-only

16/28
 NA 09. 92 B
CONNECT 2
09 - 2010
COMMUNICATION PROTOCOL 3991051.01

Hexadecimal Decimal
Description Format Type Setting
bit number bit number

0x21fa & 0x21fb 8698 & 8699 Circuit x water outlet temperature Float Read-only
0x21fc & 0x21fd 8700 & 8701 Hot water temperature Float Read-only
0x21fe & 0x21ff 8702 & 8703 Refrigerant temperature Float Read-only
Fault memory area 7
Unsigned
0x2240 8768 Fault number in fault memory Read-only
int
0x2241 8769 Fault memory year Char Read-only
0x2242 8770 Fault memory month Char Read-only
0x2243 8771 Fault memory day of month Char Read-only
0x2244 8772 Fault memory hour Char Read-only
0x2245 8773 Fault memory minutes Char Read-only
0x2246 & 0x2247 8774 & 8775 Fault memory HP Float Read-only
0x2248 & 0x2249 8776 & 8777 Fault memory condensing temperature Float Read-only
0x224a & 0x224b 8778 & 8779 Fault memory LP Float Read-only
0x224c & 0x224d 8780 & 8781 Fault memory evaporating temperature Float Read-only
0x224e & 0x224f 8782 & 8783 Fault memory suction temperature Float Read-only
0x2250 & 0x2251 8784 & 8785 Fault memory superheat Float Read-only
0x2252 8786 Stage 1 circuit x discharge Char Read-only
0x2253 8787 Stage 2 circuit x discharge Char Read-only
0x2254 & 0x2255 8788 & 8789 Outdoor temperature Float Read-only
0x2256 & 0x2257 8790 & 8791 Control setpoint Float Read-only
0x2258 & 0x2259 8792 & 8793 Water inlet temperature Float Read-only
0x225a & 0x225b 8794 & 8795 Circuit x water outlet temperature Float Read-only
0x225c & 0x225d 8796 & 8797 Hot water temperature Float Read-only
0x225e & 0x225f 8798 & 8799 Refrigerant temperature Float Read-only
Fault memory area 8
Unsigned
0x22a0 8864 Fault number in fault memory Read-only
int
0x22a1 8865 Fault memory year Char Read-only
0x22a2 8866 Fault memory month Char Read-only
0x22a3 8867 Fault memory day of month Char Read-only
0x22a4 8868 Fault memory hour Char Read-only
0x22a5 8869 Fault memory minutes Char Read-only
0x22a6 & 0x22a7 8870 & 8871 Fault memory HP Float Read-only
0x22a8 & 0x22a9 8872 & 8873 Fault memory condensing temperature Float Read-only
0x22aa & 0x22ab 8874 & 8875 Fault memory LP Float Read-only
0x22ac & 0x22ad 8876 & 8877 Fault memory evaporating temperature Float Read-only
0x22ae & 0x22af 8878 & 8879 Fault memory suction temperature Float Read-only
0x22b0 & 0x22b1 8880 & 8881 Fault memory superheat Float Read-only
0x22b2 8882 Stage 1 circuit x discharge Char Read-only
0x22b3 8883 Stage 2 circuit x discharge Char Read-only
0x22b4 & 0x22b5 8884 & 8885 Outdoor temperature Float Read-only
0x22b6 & 0x22b7 8886 & 8887 Control setpoint Float Read-only
0x22b8 & 0x22b9 8888 & 8889 Water inlet temperature Float Read-only
0x22ba & 0x22bb 8890 & 8891 Circuit x water outlet temperature Float Read-only
0x22bc & 0x22bd 8892 & 8893 Hot water temperature Float Read-only
0x22be & 0x22bf 8894 & 8895 Refrigerant temperature Float Read-only

17/28
 NA 09. 92 B
CONNECT 2
09 - 2010
COMMUNICATION PROTOCOL 3991051.01

Hexadecimal Decimal
Description Format Type Setting
bit number bit number

Fault memory area 9

Unsigned
0x2300 8960 Fault number in fault memory Read-only
int
0x2301 8961 Fault memory year Char Read-only
0x2302 8962 Fault memory month Char Read-only
0x2303 8963 Fault memory day of month Char Read-only
0x2304 8964 Fault memory hour Char Read-only
0x2305 8965 Fault memory minutes Char Read-only
0x2306 & 0x2307 8966 & 8967 Fault memory HP Float Read-only
0x2308 & 0x2309 8968 & 8969 Fault memory condensing temperature Float Read-only
0x230a & 0x230b 8970 & 8971 Fault memory LP Float Read-only
0x230c & 0x230d 8972 & 8973 Fault memory evaporating temperature Float Read-only
0x230e & 0x230f 8974 & 8975 Fault memory suction temperature Float Read-only
0x2310 & 0x2311 8976 & 8977 Fault memory superheat Float Read-only
0x2312 8978 Stage 1 circuit x discharge Char Read-only
0x2313 8979 Stage 2 circuit x discharge Char Read-only
0x2314 & 0x2315 8980 & 8981 Outdoor temperature Float Read-only
0x2316 & 0x2317 8982 & 8983 Control setpoint Float Read-only
0x2318 & 0x2319 8984 & 8985 Water inlet temperature Float Read-only
0x231a & 0x231b 8986 & 8987 Circuit x water outlet temperature Float Read-only
0x231c & 0x231d 8988 & 8989 Hot water temperature Float Read-only
0x231e & 0x231f 8990 & 8991 Refrigerant temperature Float Read-only
Fault memory area 10
Unsigned
0x2360 9056 Fault number in fault memory Read-only
int
0x2361 9057 Fault memory year Char Read-only
0x2362 9058 Fault memory month Char Read-only
0x2363 9059 Fault memory day of month Char Read-only
0x2364 9060 Fault memory hour Char Read-only
0x2365 9061 Fault memory minutes Char Read-only
0x2366 & 0x2367 9062 & 9063 Fault memory HP Float Read-only
0x2368 & 0x2369 9064 & 9065 Fault memory condensing temperature Float Read-only
0x236a & 0x236b 9066 & 9067 Fault memory LP Float Read-only
0x236c & 0x236d 9068 & 9069 Fault memory evaporating temperature Float Read-only
0x236e & 0x236f 9070 & 9071 Fault memory suction temperature Float Read-only
0x2370 & 0x2371 9072 & 9073 Fault memory superheat Float Read-only
0x2372 9074 Stage 1 circuit x discharge Char Read-only
0x2373 9075 Stage 2 circuit x discharge Char Read-only
0x2374 & 0x2375 9076 & 9077 Outdoor temperature Float Read-only
0x2376 & 0x2377 9078 & 9079 Control setpoint Float Read-only
0x2378 & 0x2379 9080 & 9081 Water inlet temperature Float Read-only
0x237a & 0x237b 9082 & 9083 Circuit x water outlet temperature Float Read-only
0x237c & 0x237d 9084 & 9085 Hot water temperature Float Read-only
0x237e & 0x237f 9086 & 9087 Refrigerant temperature Float Read-only

18/28
 NA 09. 92 B
CONNECT 2
09 - 2010
COMMUNICATION PROTOCOL 3991051.01

Hexadecimal Decimal
Description Format Type Setting
bit number bit number

Fault memory area 11

Unsigned
0x23c0 9152 Fault number in fault memory Read-only
int
0x23c1 9153 Fault memory year Char Read-only
0x23c2 9154 Fault memory month Char Read-only
0x23c3 9155 Fault memory day of month Char Read-only
0x23c4 9156 Fault memory hour Char Read-only
0x23c5 9157 Fault memory minutes Char Read-only
0x23c6 & 0x23c7 9158 & 9159 Fault memory HP Float Read-only
0x23c8 & 0x23c9 9160 & 9161 Fault memory condensing temperature Float Read-only
0x23ca & 0x23cb 9162 & 9163 Fault memory LP Float Read-only
0x23cc & 0x23cd 9164 & 9165 Fault memory evaporating temperature Float Read-only
0x23ce & 0x23cf 9166 & 9167 Fault memory suction temperature Float Read-only
0x23d0 & 0x23d1 9168 & 9169 Fault memory superheat Float Read-only
0x23d2 9170 Stage 1 circuit x discharge Char Read-only
0x23d3 9171 Stage 2 circuit x discharge Char Read-only
0x23d4 & 0x23d5 9172 & 9173 Outdoor temperature Float Read-only
0x23d6 & 0x23d7 9174 & 9175 Control setpoint Float Read-only
0x23d8 & 0x23d9 9176 & 9177 Water inlet temperature Float Read-only
0x23da & 0x23db 9178 & 9179 Circuit x water outlet temperature Float Read-only
0x23dc & 0x23dd 9180 & 9181 Hot water temperature Float Read-only
0x23de & 0x23df 9182 & 9183 Refrigerant temperature Float Read-only
Fault memory area 12
Unsigned
0x2420 9248 Fault number in fault memory Read-only
int
0x2421 9249 Fault memory year Char Read-only
0x2422 9250 Fault memory month Char Read-only
0x2423 9251 Fault memory day of month Char Read-only
0x2424 9252 Fault memory hour Char Read-only
0x2425 9253 Fault memory minutes Char Read-only
0x2426 & 0x2427 9254 & 9255 Fault memory HP Float Read-only
0x2428 & 0x2429 9256 & 9257 Fault memory condensing temperature Float Read-only
0x242a & 0x242b 9258 & 9259 Fault memory LP Float Read-only
0x242c & 0x242d 9260 & 9261 Fault memory evaporating temperature Float Read-only
0x242e & 0x242f 9262 & 9263 Fault memory suction temperature Float Read-only
0x2430 & 0x2431 9264 & 9265 Fault memory superheat Float Read-only
0x2432 9266 Stage 1 circuit x discharge Char Read-only
0x2433 9267 Stage 2 circuit x discharge Char Read-only
0x2434 & 0x2435 9268 & 9269 Outdoor temperature Float Read-only
0x2436 & 0x2437 9270 & 9271 Control setpoint Float Read-only
0x2438 & 0x2439 9272 & 9273 Water inlet temperature Float Read-only
0x243a & 0x243b 9274 & 9275 Circuit x water outlet temperature Float Read-only
0x243c & 0x243d 9276 & 9277 Hot water temperature Float Read-only
0x243e & 0x243f 9278 & 9279 Refrigerant temperature Float Read-only

19/28
 NA 09. 92 B
CONNECT 2
09 - 2010
COMMUNICATION PROTOCOL 3991051.01

Hexadecimal Decimal
Description Format Type Setting
bit number bit number

Fault memory area 13

Unsigned
0x2480 9344 Fault number in fault memory Read-only
int
0x2481 9345 Fault memory year Char Read-only
0x2482 9346 Fault memory month Char Read-only
0x2483 9347 Fault memory day of month Char Read-only
0x2484 9348 Fault memory hour Char Read-only
0x2485 9349 Fault memory minutes Char Read-only
0x2486 & 0x2487 9350 & 9351 Fault memory HP Float Read-only
0x2488 & 0x2489 9352 & 9353 Fault memory condensing temperature Float Read-only
0x248a & 0x248b 9354 & 9355 Fault memory LP Float Read-only
0x248c & 0x248d 9356 & 9357 Fault memory evaporating temperature Float Read-only
0x248e & 0x248f 9358 & 9359 Fault memory suction temperature Float Read-only
0x2490 & 0x2491 9360 & 9361 Fault memory superheat Float Read-only
0x2492 9362 Stage 1 circuit x discharge Char Read-only
0x2493 9363 Stage 2 circuit x discharge Char Read-only
0x2494 & 0x2495 9364 & 9365 Outdoor temperature Float Read-only
0x2496 & 0x2497 9366 & 9367 Control setpoint Float Read-only
0x2498 & 0x2499 9368 & 9369 Water inlet temperature Float Read-only
0x249a & 0x249b 9370 & 9371 Circuit x water outlet temperature Float Read-only
0x249c & 0x249d 9372 & 9373 Hot water temperature Float Read-only
0x249e & 0x249f 9374 & 9375 Refrigerant temperature Float Read-only
Fault memory area 14
Unsigned
0x24e0 9440 Fault number in fault memory Read-only
int
0x24e1 9441 Fault memory year Char Read-only
0x24e2 9442 Fault memory month Char Read-only
0x24e3 9443 Fault memory day of month Char Read-only
0x24e4 9444 Fault memory hour Char Read-only
0x24e5 9445 Fault memory minutes Char Read-only
0x24e6 & 0x24e7 9446 & 9447 Fault memory HP Float Read-only
0x24e8 & 0x24e9 9448 & 9449 Fault memory condensing temperature Float Read-only
0x24ea & 0x24eb 9450 & 9451 Fault memory LP Float Read-only
0x24ec & 0x24ed 9452 & 9453 Fault memory evaporating temperature Float Read-only
0x24ee & 0x24ef 9454 & 9455 Fault memory suction temperature Float Read-only
0x24f0 & 0x24f1 9456 & 9457 Fault memory superheat Float Read-only
0x24f2 9458 Stage 1 circuit x discharge Char Read-only
0x24f3 9459 Stage 2 circuit x discharge Char Read-only
0x24f4 & 0x24f5 9460 & 9461 Outdoor temperature Float Read-only
0x24f6 & 0x24f7 9462 & 9463 Control setpoint Float Read-only
0x24f8 & 0x24f9 9464 & 9465 Water inlet temperature Float Read-only
0x24fa & 0x24fb 9466& 9467 Circuit x water outlet temperature Float Read-only
0x24fc & 0x24fd 9468 & 9469 Hot water temperature Float Read-only
0x24fe & 0x24ff 9470 & 9471 Refrigerant temperature Float Read-only

20/28
 NA 09. 92 B
CONNECT 2
09 - 2010
COMMUNICATION PROTOCOL 3991051.01

Hexadecimal Decimal
Description Format Type Setting
bit number bit number

Fault memory area 15

Unsigned
0x2540 9536 Fault number in fault memory Read-only
int
0x2541 9537 Fault memory year Char Read-only
0x2542 9538 Fault memory month Char Read-only
0x2543 9539 Fault memory day of month Char Read-only
0x2544 9540 Fault memory hour Char Read-only
0x2545 9541 Fault memory minutes Char Read-only
0x2546 & 0x2547 9542 & 9543 Fault memory HP Float Read-only
0x2548 & 0x2549 9544 & 9545 Fault memory condensing temperature Float Read-only
0x254a & 0x254b 9546 & 9547 Fault memory LP Float Read-only
0x254c & 0x254d 9548 & 9549 Fault memory evaporating temperature Float Read-only
0x254e & 0x254f 9550 & 9551 Fault memory suction temperature Float Read-only
0x2550 & 0x2551 9552 & 9553 Fault memory superheat Float Read-only
0x2552 9554 Stage 1 circuit x discharge Char Read-only
0x2553 9555 Stage 2 circuit x discharge Char Read-only
0x2554 & 0x2555 9556 & 9557 Outdoor temperature Float Read-only
0x2556 & 0x2557 9558 & 9559 Control setpoint Float Read-only
0x2558 & 0x2559 9560 & 9561 Water inlet temperature Float Read-only
0x255a & 0x255b 9562 & 9563 Circuit x water outlet temperature Float Read-only
0x255c & 0x255d 9564 & 9565 Hot water temperature Float Read-only
0x255e & 0x255f 9566 & 9567 Refrigerant temperature Float Read-only
Fault memory area 16
Unsigned
0x25a0 9632 Fault number in fault memory Read-only
int
0x25a1 9633 Fault memory year Char Read-only
0x25a2 9634 Fault memory month Char Read-only
0x25a3 9635 Fault memory day of month Char Read-only
0x25a4 9636 Fault memory hour Char Read-only
0x25a5 9637 Fault memory minutes Char Read-only
0x25a6 & 0x25a7 9638 & 9639 Fault memory HP Float Read-only
0x25a8 & 0x25a9 9640 & 9641 Fault memory condensing temperature Float Read-only
0x25aa & 0x25ab 9642 & 9643 Fault memory LP Float Read-only
0x25ac & 0x25ad 9644 & 9645 Fault memory evaporating temperature Float Read-only
0x25ae & 0x25af 9646 & 9647 Fault memory suction temperature Float Read-only
0x25b0 & 0x25b1 9648 & 9649 Fault memory superheat Float Read-only
0x25b2 9650 Stage 1 circuit x discharge Char Read-only
0x25b3 9651 Stage 2 circuit x discharge Char Read-only
0x25b4 & 0x25b5 9652 & 9653 Outdoor temperature Float Read-only
0x25b6 & 0x25b7 9654 & 9655 Control setpoint Float Read-only
0x25b8 & 0x25b9 9656 & 9657 Water inlet temperature Float Read-only
0x25ba & 0x25bb 9658 & 9659 Circuit x water outlet temperature Float Read-only
0x25bc & 0x25bd 9660 & 9661 Hot water temperature Float Read-only
0x25be & 0x25bf 9662 & 9663 Refrigerant temperature Float Read-only

21/28
 NA 09. 92 B
CONNECT 2
09 - 2010
COMMUNICATION PROTOCOL 3991051.01

Hexadecimal Decimal
Description Format Type Setting
bit number bit number

Fault memory area 17

Unsigned
0x2600 9728 Fault number in fault memory Read-only
int
0x2601 9729 Fault memory year Char Read-only
0x2602 9730 Fault memory month Char Read-only
0x2603 9731 Fault memory day of month Char Read-only
0x2604 9732 Fault memory hour Char Read-only
0x2605 9733 Fault memory minutes Char Read-only
0x2606 & 0x2607 9734 & 9735 Fault memory HP Float Read-only
0x2608 & 0x2609 9736 & 9737 Fault memory condensing temperature Float Read-only
0x260a & 0x260b 9738 & 9739 Fault memory LP Float Read-only
0x260c & 0x260d 9740 & 9741 Fault memory evaporating temperature Float Read-only
0x260e & 0x260f 9742 & 9743 Fault memory suction temperature Float Read-only
0x2610 & 0x2611 9744 & 9745 Fault memory superheat Float Read-only
0x2612 9746 Stage 1 circuit x discharge Char Read-only
0x2613 9747 Stage 2 circuit x discharge Char Read-only
0x2614 & 0x2615 9748 & 9749 Outdoor temperature Float Read-only
0x2616 & 0x2617 9750 & 9751 Control setpoint Float Read-only
0x2618 & 0x2619 9752 & 9753 Water inlet temperature Float Read-only
0x261a & 0x261b 9754 & 9755 Circuit x water outlet temperature Float Read-only
0x261c & 0x261d 9756 & 9757 Hot water temperature Float Read-only
0x261e & 0x261f 9758 & 9759 Refrigerant temperature Float Read-only
Fault memory area 18
Unsigned
0x2660 9824 Fault number in fault memory Read-only
int
0x2661 9825 Fault memory year Char Read-only
0x2662 9826 Fault memory month Char Read-only
0x2663 9827 Fault memory day of month Char Read-only
0x2664 9828 Fault memory hour Char Read-only
0x2665 9829 Fault memory minutes Char Read-only
0x2666 & 0x2667 9830 & 9831 Fault memory HP Float Read-only
0x2668 & 0x2669 9832 & 9833 Fault memory condensing temperature Float Read-only
0x266a & 0x266b 9834 & 9835 Fault memory LP Float Read-only
0x266c & 0x266d 9836 & 9837 Fault memory evaporating temperature Float Read-only
0x266e & 0x266f 9838 & 9839 Fault memory suction temperature Float Read-only
0x2670 & 0x2671 9840 & 9841 Fault memory superheat Float Read-only
0x2672 9842 Stage 1 circuit x discharge Char Read-only
0x2673 9843 Stage 2 circuit x discharge Char Read-only
0x2674 & 0x2675 9844 & 9845 Outdoor temperature Float Read-only
0x2676 & 0x2677 9846 & 9847 Control setpoint Float Read-only
0x2678 & 0x2679 9848 & 9849 Water inlet temperature Float Read-only
0x267a & 0x267b 9850 & 9851 Circuit x water outlet temperature Float Read-only
0x267c & 0x267d 9852 & 9853 Hot water temperature Float Read-only
0x267e & 0x267f 9854 & 9855 Refrigerant temperature Float Read-only

22/28
 NA 09. 92 B
CONNECT 2
09 - 2010
COMMUNICATION PROTOCOL 3991051.01

Hexadecimal Decimal
Description Format Type Setting
bit number bit number

Fault memory area 19

Unsigned
0x26c0 9920 Fault number in fault memory Read-only
int
0x26c1 9921 Fault memory year Char Read-only
0x26c2 9922 Fault memory month Char Read-only
0x26c3 9923 Fault memory day of month Char Read-only
0x26c4 9924 Fault memory hour Char Read-only
0x26c5 9925 Fault memory minutes Char Read-only
0x26c6 & 0x26c7 9926 & 9927 Fault memory HP Float Read-only
0x26c8 & 0x26c9 9928 & 9929 Fault memory condensing temperature Float Read-only
0x26ca & 0x26cb 9930 & 9931 Fault memory LP Float Read-only
0x26cc & 0x26cd 9932 & 9933 Fault memory evaporating temperature Float Read-only
0x26ce & 0x26cf 9934 & 9935 Fault memory suction temperature Float Read-only
0x26d0 & 0x26d1 9936 & 9937 Fault memory superheat Float Read-only
0x26d2 9938 Stage 1 circuit x discharge Char Read-only
0x26d3 9939 Stage 2 circuit x discharge Char Read-only
0x26d4 & 0x26d5 9940 & 9941 Outdoor temperature Float Read-only
0x26d6 & 0x26d7 9942 & 9943 Control setpoint Float Read-only
0x26d8 & 0x26d9 9944 & 9945 Water inlet temperature Float Read-only
0x26da & 0x26db 9946 & 9947 Circuit x water outlet temperature Float Read-only
0x26dc & 0x26dd 9948 & 9949 Hot water temperature Float Read-only
0x26de & 0x26df 9950 & 9951 Refrigerant temperature Float Read-only
Fault memory area 20
Unsigned
0x2720 10016 Fault number in fault memory Read-only
int
0x2721 10017 Fault memory year Char Read-only
0x2722 10018 Fault memory month Char Read-only
0x2723 10019 Fault memory day of month Char Read-only
0x2724 10020 Fault memory hour Char Read-only
0x2725 10021 Fault memory minutes Char Read-only
0x2726 & 0x2727 10022 & 10023 Fault memory HP Float Read-only
0x2728 & 0x2729 10024 & 10025 Fault memory condensing temperature Float Read-only
0x272a & 0x272b 10026 & 10027 Fault memory LP Float Read-only
0x272c & 0x272d 10028 & 10029 Fault memory evaporating temperature Float Read-only
0x272e & 0x272f 10030 & 10031 Fault memory suction temperature Float Read-only
0x2730 & 0x2731 10032 & 10033 Fault memory superheat Float Read-only
0x2732 10034 Stage 1 circuit x discharge Char Read-only
0x2733 10035 Stage 2 circuit x discharge Char Read-only
0x2734 & 0x2735 10036 & 10037 Outdoor temperature Float Read-only
0x2736 & 0x2737 10038 & 10039 Control setpoint Float Read-only
0x2738 & 0x2739 10040 & 10041 Water inlet temperature Float Read-only
0x273a & 0x273b 10042 & 10043 Circuit x water outlet temperature Float Read-only
0x273c & 0x273d 10044 & 10045 Hot water temperature Float Read-only
0x273e & 0x273f 10046 & 10047 Refrigerant temperature Float Read-only

23/28
 NA 09. 92 B
CONNECT 2
09 - 2010
COMMUNICATION PROTOCOL 3991051.01

NUMERICAL LIST OF FAULTS

Decimal
Hexadecimal
fault Description
fault number
number
0x002 2 Power cut
0x003 3 Water flow fault
0x004 4 Outdoor temperature too low
0x005 5 Fan fault
0x006 6 Auxiliary heater board input 1 fault
0x007 7 Auxiliary heater board input 2 fault
0x008 8 EEPROM fault
0x00c 12 Automated self-regulating control
0x00d 13 Multiconnect link fault
0x012 18 Aeroconnect fault
0x013 19 Aeroconnect link fault
0x014 20 Outdoor temperature too high in cooling mode

0x081 129 Outdoor temperature sensor fault

0x082 130 Exchanger water inlet sensor fault
0x083 131 Exchanger water outlet sensor fault
0x084 132 Condenser sensor fault
0x085 133 Manifold outlet sensor fault
0x086 134 Exchanger ambient sensor fault
0x087 135 Pump 1 fault
0x088 136 Pump 2 fault
0x089 137 Phase controller fault

0x101 257 Circuit 1 frosting fault

0x102 258 Circuit 1 refrigerant frosting fault
0x103 259 NU
0x104 260 NU
0x105 261 NU
0x106 262 Circuit 1 LP fault
0x107 263 Circuit 1 HP fault
0x108 264 Manual HP fault, circuit 1
0x109 265 Circuit 1 motor 1 fault
0x10a 266 Circuit 1 motor 2 fault
0x10b 267 Circuit 1 discharge fault
0x10c 268 Circuit 1 defrosting fault
0x10d 269 NU
0x10e 270 Circuit 1 exchanger frosting fault
0x10f 271 NU
0x110 272 Circuit 1 Alco expansion valve fault
0x111 273 Circuit 1 maximum superheat fault

0x181 385 Coil A circuit 1 sensor freon fault

0x182 386 Circuit 1 exchanger freon fault
0x183 387 Circuit 1 exchanger water outlet sensor fault
0x184 388 NU

24/28
 NA 09. 92 B
CONNECT 2
09 - 2010
COMMUNICATION PROTOCOL 3991051.01

Decimal
Hexadecimal
fault Description
fault number
number
0x185 389 Circuit 1 HP sensor fault
0x186 390 Circuit 1 LP sensor fault
0x187 391 Coil B circuit 1 freon sensor fault
0x188 392 Circuit 1 suction sensor fault
0x189 393 Circuit 1 expansion valve board link fault
0x18a 394 Circuit 1 expansion valve motor fault
0x18b 395 Circuit 1 superheat fault
0x18c 396 Circuit 1 VCM module fault
0x18d 397 Circuit 1 inverter discharge fault
0x18e 398 Auxiliary heater board link fault
0x18f 399 Circuit 1 reversible board link fault
0x190 400 Circuit 2 reversible board link fault
0x191 401 Coil C circuit 1 freon sensor fault
0x192 402 Coil D circuit 1 freon sensor fault
0x193 403 Circuit 1 liquid sensor fault
0x194 404 Stage 1, circuit 1 discharge sensor fault
0x195 405 Stage 2, circuit 1 discharge sensor fault

0x201 513 Circuit 2 frosting fault

0x202 514 Circuit 2 refrigerant frosting fault
0x203 515 NU
0x204 516 NU
0x205 517 NU
0x206 518 Circuit 2 LP fault
0x207 519 Circuit 2 HP fault
0x208 520 Manual HP fault, circuit 2
0x209 521 Circuit 2 motor 1 fault
0x20a 522 Circuit 2 motor 2 fault
0x20b 523 Circuit 2 discharge fault
0x20c 524 Circuit 2 defrosting fault
0x20d 525 NU
0x20e 526 Circuit 2 exchanger frosting fault
0x20f 527 NU
0x210 528 Circuit 2 Alco expansion valve fault
0x211 529 Circuit 2 maximum superheat fault

0x281 641 Circuit 2 coil A sensor freon fault

0x282 642 Circuit 2 exchanger freon fault
0x283 643 Circuit 2 exchanger water outlet sensor fault
0x284 644 NU
0x285 645 Circuit 2 HP sensor fault
0x286 646 Circuit 2 LP sensor fault
0x287 647 Coil B circuit 2 freon sensor fault
0x288 648 Circuit 2 suction sensor fault
0x289 649 Circuit 2 expansion valve board link fault
0x28a 650 Circuit 2 expansion valve motor fault
0x28b 651 Circuit 2 superheat fault

25/28
 NA 09. 92 B
CONNECT 2
09 - 2010
COMMUNICATION PROTOCOL 3991051.01

Decimal
Hexadecimal
fault Description
fault number
number
0x28c 652 Circuit 2 VCM module fault
0x28d 653 Coil C circuit 2 freon sensor fault
0x28e 654 Coil D circuit 2 freon sensor fault
0x28f 655 Circuit 2 liquid sensor fault
0x290 656 Discharge 4 sensor fault
0x291 657 Stage 1, circuit 1 discharge sensor fault
0x292 658 Stage 2, circuit 1 discharge sensor fault

TIME SCHEDULES

Hexadecimal Decimal bit

Description Format Type Setting
bit number number

Registers accessible in read mode (functions 3 or 4) and write mode (functions 6 for 'Char' or 16)
Time schedule 1
0x3000 12288 Start time Char Read/Write
0x3001 12289 Start minutes Char Read/Write
0x3002 12290 End time Char Read/Write
0x3003 12291 End minutes Char Read/Write
0x3004 12292 Selected day Char Read/Write
Time schedule 2
0x3010 12304 Start time Char Read/Write
0x3011 12305 Start minutes Char Read/Write
0x3012 12306 End time Char Read/Write
0x3013 12307 End minutes Char Read/Write
0x3014 12308 Selected day Char Read/Write
Time schedule 3
0x3020 12320 Start time Char Read/Write
0x3021 12321 Start minutes Char Read/Write
0x3022 12322 End time Char Read/Write
0x3023 12323 End minutes Char Read/Write
0x3024 12324 Selected day Char Read/Write
0x3025 12325 Program type Char Read/Write
Time schedule 4
0x3030 12336 Start time Char Read/Write
0x3031 12337 Start minutes Char Read/Write
0x3032 12338 End time Char Read/Write
0x3033 12339 End minutes Char Read/Write
0x3034 12340 Selected day Char Read/Write
Time schedule 5
0x3040 12352 Start time Char Read/Write
0x3041 12353 Start minutes Char Read/Write
0x3042 12354 End time Char Read/Write
0x3043 12355 End minutes Char Read/Write
0x3044 12356 Selected day Char Read/Write

26/28
 NA 09. 92 B
CONNECT 2
09 - 2010
COMMUNICATION PROTOCOL 3991051.01

Hexadecimal Decimal bit

Description Format Type Setting
bit number number

Time schedule 6
0x3050 12368 Start time Char Read/Write
0x3051 12369 Start minutes Char Read/Write
0x3052 12370 End time Char Read/Write
0x3053 12371 End minutes Char Read/Write
0x3054 12372 Selected day Char Read/Write
Holiday zone 1
0x3100 12544 Start day Char Read/Write
0x3101 12545 Start month Char Read/Write
0x3102 12546 End day Char Read/Write
0x3103 12547 End month Char Read/Write
0x3104 12548 Zone type Char Read/Write
Holiday zone 2
0x3110 12560 Start day Char Read/Write
0x3111 12561 Start month Char Read/Write
0x3112 12562 End day Char Read/Write
0x3113 12563 End month Char Read/Write
0x3114 12564 Zone type Char Read/Write
Holiday zone 3
0x3120 12576 Start day Char Read/Write
0x3121 12577 Start month Char Read/Write
0x3122 12578 End day Char Read/Write
0x3123 12579 End month Char Read/Write
0x3124 12580 Zone type Char Read/Write
Holiday zone 4
0x3130 12592 Start day Char Read/Write
0x3131 12593 Start month Char Read/Write
0x3132 12594 End day Char Read/Write
0x3133 12595 End month Char Read/Write
0x3134 12596 Zone type Char Read/Write
Holiday zone 5
0x3140 12608 Start day Char Read/Write
0x3141 12609 Start month Char Read/Write
0x3142 12610 End day Char Read/Write
0x3143 12611 End month Char Read/Write
0x3144 12612 Zone type Char Read/Write
Holiday zone 6
0x3150 12624 Start day Char Read/Write
0x3151 12625 Start month Char Read/Write
0x3152 12626 End day Char Read/Write
0x3153 12627 End month Char Read/Write
0x3154 12628 Zone type Char Read/Write

27/28
 NA 09. 92 B
CONNECT 2
09 - 2010
COMMUNICATION PROTOCOL 3991051.01

Program type Description Zone type Description

0 Programme deselected 0 Zone deselected

1 Setpoint 1 - off 1 Off
2 Setpoint 2 - off 2 Start on setpoint 1
3 Setpoint 1 - setpoint 2 3 Start on setpoint 2
4 Setpoint 2 - setpoint 1
Selected day
Bit 0 1 = Monday selected
Bit 1 1 = Tuesday selected
Bit 2 1 = Wednesday selected
Bit 3 1 = Thursday selected
Bit 4 1 = Friday selected
Bit 5 1 = Saturday selected
Bit 6 1 = Sunday selected
Bit 7 NU

This document is non-contractual. As part of its policy of continual product improvement, CIAT reserves the right to make any technical modification it feels appropriate without prior notification.

Head office CIAT service

Avenue Jean Falconnier – B.P.14 Tél. : +33 (0)4 79 42 42 90 – Fax : +33 (0)4 79 42 42 13
01350 - Culoz - France
Tél. +33 (0)4 79 42 42 42 – Fax : +33 (0)4 79 42 42 10 ISO 9001 – ISO 14001
OHSAS 18001
[email protected] - www.ciat.com

Compagnie Industrielle d’Applications Thermiques – S.A. with a registered capital of 26 728 480 € - R.C.S. Bourg-en-Bresse B 545.620.114

28/28