BMR SERIES HYDRAULIC MOTOR
BMR series motor adapt the advanced Gerolor gear set design with shaft distribution flow,
which can automatically compensate in operating with high pressure, provide reliable and smooth
operation, high efficiency and long life.
Characteristic features:
*Advanced manufacturing devices for the Gerolor gear set, which use low pressure of start-up,
provide smooth, reliable operation and high efficiency.
*Shaft seal can bear high pressure of back and the motor can be used in parallel or in series.
*Special design in the driver-linker and prolong operating life
*Special design for distribution system can meet the requirement of low noise of unit.
*Compact volume and easy installation
Main Specification
Technical data for BMR with 25 and 1 in and 1 in splined and 28.56 tapered shaft
BMR BMR BMR BMR BMR BMR BMR BMR BMR BMR
Type BMRS BMRS BMRS BMRS BMRS BMRS BMRS BMRS BMRS BMRS
36 50 80 100 125 160 200 250 315 375
Geometric displacement (cm3/rev.) 36 51.7 81.5 102 127.2 157.2 194.5 253.3 317.5 381.4
cont. 1085 960 750 600 475 378 310 240 190 155
Max. speed (rpm)
int. 1220 1150 940 750 600 475 385 300 240 190
cont. 72 100 195 240 300 360 360 390 390 365
Max. torque (N•m) int. 83 126 220 280 340 430 440 490 535 495
peak 105 165 270 320 370 460 560 640 650 680
cont. 8.5 9.5 12.5 13.0 12.5 12.5 10.0 7.0 6.0 5.0
Max. output (kW)
int. 9.8 11.2 15.0 15.0 14.5 14.0 13.0 9.5 9.0 8.0
cont. 14.0 14 17.5 17.5 17.5 16.5 13 11 9 7
Max. pressure
int. 16.5 17.5 20 20 20 20 17.5 15 13 10
drop (MPa)
peak 22.5 22.5 22.5 22.5 22.5 22.5 22.5 20 17.5 15
cont. 40 50 60 60 60 60 60 60 60 60
Max. flow (L/min)
int. 45 60 75 75 75 75 75 75 75 75
Weight (kg) 6.5 6.7 6.9 7 7.3 7.6 8.0 8.5 9.0 9.5
* Continuous pressure:Max.value of operating motor continuously.
* Intermittent pressure:Max.value of operating motor in 6 seconds per minute .
* Peak pressure:Max.value of operating motor in 0.6 second per minute.
18
Main Specification
Technical data for BMR with 31.75 and 32 shaft
BMR BMR BMR BMR BMR BMR BMR BMR BMR BMR
Type BMRS BMRS BMRS BMRS BMRS BMRS BMRS BMRS BMRS BMRS
36 50 80 100 125 160 200 250 315 375
Geometric displacement (cm3/rev.) 36 51.7 81.5 102 127.2 157.2 194.5 253.3 317.5 381.4
cont. 1250 960 750 600 475 378 310 240 190 155
Max. speed (rpm)
int. 1520 1150 940 750 600 475 385 300 240 190
cont. 72 100 195 240 300 380 450 540 550 580
Max. torque (N•m) int. 83 126 220 280 340 430 500 610 690 690
peak 105 165 270 320 370 460 560 710 840 830
cont. 8.5 9.5 12.5 13.0 12.5 12.5 11.0 10.0 9.0 7.5
Max. output (kW)
int. 9.8 11.2 15.0 15.0 14.5 14.0 13.0 12.0 10.0 9.0
cont. 14.0 14 17.5 17.5 17.5 17.5 17.5 17.5 13.5 11.5
Max. pressure
int. 16.5 17.5 20 20 20 20 20 20 17.5 15
drop (MPa)
peak 22.5 22.5 22.5 22.5 22.5 22.5 22.5 22.5 21 17.5
cont. 45 50 60 60 60 60 60 60 60 60
Max. flow (L/min)
int. 55 60 75 75 75 75 75 75 75 75
Weight (kg) 6.5 6.7 6.9 7 7.3 7.6 8.0 8.5 9.0 9.5
* Continuous pressure:Max.value of operating motor continuously.
* Intermittent pressure:Max.value of operating motor in 6 seconds per minute .
* Peak pressure:Max.value of operating motor in 0.6 second per minute.
19
BMR DIMENSIONS AND MOUNTING DATA
MOUNTING
Flange 2
PORT
Flange 4
Model L L1 Flange H4/H5
BMR36 137 7
BMR50 140 10
BMR80 146 16
BMR100 150 20
BMR125 155 25
BMR160 161.5 30.5
BMR200 170 38.1
BMR250 180 50
BMR315 192 62
BMR375 204 74
Code
D (depth) M (depth) S (depth) P (depth) R (depth)
Mounting
P(A,B) G1/2 (15) M22 x 1.5 (15) 7/8-14 O-ring (17) 1/2-14NPTF (15) PT(RC)1/2 (15)
C 4-M8 (13) 4-M8 (13) 4-5/16-18UNC(13) 4-5/16-18UNC(13) 4-M8 (13)
T G1/4 (12) M14 x 1.5 (12) 7/16-20UNF (12) 7/16-20UNF (12) PT(RC)1/4 (9.7)
20
BMRS DIMENSIONS AND MOUNTING DATA
MOUNTING
Flange H2
PORT: G、S、P、R、M1、M2、
M3
Flange H6
PORT: B4、B5
Model L L1 Flange H4/H5
BMRS36 141 7
BMRS50 144 10
BMRS80 150 16
BMRS100 154 20
BMRS125 159 25
BMRS160 165.5 30.5
BMRS200 174 38.1
BMRS250 184 50
BMRS315 196 62
BMRS375 208 74
Code
G (depth) S (depth) P (depth) R (depth) M1 (depth) M2 (depth) M3 (depth) B4 (depth) B5 (depth)
Mounting
P(A,B) G1/2 (15) 7/8-14 O-ring (17) 1/2-14NPTF (15) PT(RC)1/2 (15) M18 x 1.5 (15) M20 x 1.5 (15) M22 x 1.5 (15) ø10 ø10
T G1/4 (12) 7/16-20UNF (12) 7/16-20UNF (12) PT(RC)1/4 (9.7) M10 x 1 (12) M10 x 1 (12) M10 x 1 (12) 7/16-20UNF(12) G1/4(12)
C – – – – – – – 4-5/16-18UNC(13) 4-M8(13)
21
BMR SHAFT EXTENSIONS DIMENSIONS DATA
Shaft A: Cylindrical shaft ø25 Shaft B: Cylindrical shaft ø32
Parallel key 8x7x32 Parallel key 10x8x45
Shaft C: Cylindrical shaft ø25.4
Parallel key 6.35x6.35x31.75
Shaft E: Splined SAE 6B
Shaft F: Splined
14-DP12/24 Shaft G: Cylindrical shaft ø31.75
Parallel key 7.96x7.96x31.75
Shaft T: Cone-shaft ø28.56 Shaft R:Cylindrical shaftø25.4
Parallel key B5x5x14 Parallel key 6.35x6.35x31.75
Tightening torque:100±10Nm
△
Motor Mounting Surface
22
23
BMRS SHAFT EXTENSIONS DIMENSIONS DATA
Shaft A: Cylindrical shaft ø25
Parallel key 8x7x32 Shaft H1: Cylindrical shaft ø25.4
Pin hole ø8
Shaft R: Cylindrical shaftø25.4 Shaft D: Cylindrical shaft ø22.22
Parallel key 6.35x6.35x31.75 Parallel key 6.35x6.35x25.4
Shaft T2: Cone-shaft ø25.4
Parallel key ø25.4x6.35
Tightening torque:200±10Nm
Motor Mounting Surface
△
24
Order Information 1 2 3 4 5 6 7 8
BMR
Pos.1 2 3 4 5 6 7 8
Code Disp. Flange Output Shaft Port and Drain Port Rotation Direction Paint Unusually Function
36 D G1/2 Manifold Mount
A Shaft Ø25,parallel Key 8x7x32
50 4-M8, G1/4
2 2-Ø13.5Rhomb-flange, B Shaft Ø32,parallel Key 10x8x45
80 M M22×1.5 Manifold Mount
pilot Ø82.5×8 Shaft Ø25.4,parallel Key 6.35x6.35x31.75
C 4-M8, M14×1.5 Omit Standard
100 4 4-Ø13.5Rhomb-flange, 00 No paint
E Shaft Ø25.4,splined tooth SAE 6B S 7/8-14 O-ring manifold N Big radial force
125 pilot Ø82.5×8 Omit Standard Omit Blue
BMR R Short shaft Ø25.4,parallel key 6.35x6.35x31.75 4-5/16-18UNC, 7/16-20UNF 0 No case drain
160 H4 4-3/8-16 Square-flange, R Opposite B Black
F Shaft Ø31.75,splined tooth 14-DP12/24 P 1/2-14 NPTF F Free Running
200 pilot Ø44.4×2.8 S Silver grey
FD Long shaft Ø31.75,splined tooth 14-DP12/24 Manifold 4-5/16-18UNC, LS Low Speed
250 H5 4-M10 Square-flange,
Shaft Ø31.75,parallel Key 7.96x7.96x31.75
7/16-20UNF
pilot Ø44.4×2.8 G
315 R PT(Rc)1/2 Manifold 4-M8,
T Cone-Shaft Ø28.56,parallel Key B5x5x14
375 PT(Rc)1/4
1 2 3 4 5 6 7 8
BMRS
Pos.1 2 3 4 5 6 7 8
25
Code Disp. Flange Output Shaft Port and Drain Port Rotation Direction Paint Unusually Function
K Shaft Ø25.4,Woodruff Key
Ø25.4×6.35
G G1/2, G1/4
S Sub-shaft Ø25.4,splined tooth
S 7/8-14 O-ring 7/16-20UNF
36 SAE 6B
H2 2-Ø13.5Rhomb-flange, (G1/4)
50 A Shaft Ø25 , parallel key 8×7×32
pilot Ø82.5×2.8 P 1/2-14 NPTF, 7/16-20UNF
80 R Shaft Ø25.4, parallel key
H6 4-Ø13.5Rhomb-flange, (G1/4) Omit Standard
100 6.35×6.35×31.75
pilot Ø82.5×2.8 T 3/4-16 O-ring, 7/16-20UNF 00 No paint
H Sub-shaft Ø25.4,Pin hole Ø10.3 N Big radial force
125 H4 4-3/8-16 Square-flange, R PT(Rc)1/2, PT(Rc)1/4 Omit Standard Omit Blue
BMRS H1 Shaft Ø25.4, pin hole Ø8 0 No case drain
160 pilot Ø44.4×2.8 B4 Ø10 O-ring manifold R Opposite B Black
D Shaft Ø22.22, parallel key F Free Running
200 H5 4-M10 Square-flange, 4x5/16-18, 7/16-20UNF S Silver grey
6.35×6.35×25.4 LS Low Speed
250 pilot Ø44.4×2.8 B5 Ø10 O-ring manifold 4xM8,
I Shaft Ø22.22, splined tooth
315 G1/4
13-DP16/32
M1 M18×1.5, M10×1
375 T2 Cone shaft Ø25.4 , woodruff key
M2 M20×1.5, M10×1
Ø25.4×6.35
M3 M22×1.5, M10×1
P Shaft Ø25,parallel Key 8×7×28
J Shaft Ø25,parallel Key 7×7×32
Note:When the table is used, please fill the code of left rows in dash area and give us, which the code information is consists of construction, displacement, mounting flange, output
shaft and ports. If the specification is not in the table or you have specific requirements, please contact us.
