OB3375

High performance buck LED driver

GENERAL DESCRIPTION FEATURES

The OB3375 is a high efficiency LED driver  Low system cost and high efficiency
designed for white LEDS and for large LCDS
 Quasi-Resonant buck topology operation
backlight. OB3375 is built-in a quasi-resonant
control method buck DC/DC converter. The  Programmable CC regulation
controller implements a peak current mode control  PWM and PWM to analog combination
scheme and an internal transconductance dimming
amplifier to accurately control the output current
 Zero voltage signal detected to improve
over a wide input and load conditions. The
transconductance amplifier reference is set by efficiency and EMI performance
internal reference voltage and the duty cycle at  LED+/LED- short circuit protection
HPWM pin. Low frequency LPWM dimming input  LED-/GND short circuit protection
that can accept an external control signal with a
 LED open loop protection
duty ratio of 1%-100%.
 Cycle-by-cycle current limiting
OB3375 offers comprehensive protection features
 Built-in leading edge blanking (LEB)
to protect the system in various fault conditions
 VIN under voltage lockout with hysteresis
such as Diode & Inductor short protection, CS
 Over temperature protection (OTP)
open protection, MOS drain source short
 Diode & Inductor short protection
protection, LED+/LED- short protection,
 MOSFET drain source short protection
LED-/GND short circuit protection, LED open loop
 CS open protection
protection, Over temperature protection (OTP).
 Low standby current
The cycle-by-cycle current limit function limits the
maximum current flowing through the external
MOSFET. APPLICATIONS
OB3375 is offered in SOP8 package.  LED backlight

TYPICAL APPLICATION

VIN

12V

ENA
OB3375
1
VIN GATE 8

LPWM 2 LPWM GND 7

3 HPWM CS 6

4
FAULT ZVS 5

HPWM

GND

©On-Bright Electronics Confidential Preliminary Datasheet

OB_DOC_DS_337500
-1-
 OB3375
High performance buck LED driver

GENERAL INFORMATION
Absolute Maximum Ratings Recommended Operating Range
Parameter Value Parameter Value
VIN, LPWM, HPWM, FAULT, Vin Voltage 9V to 30V
-0.3V to 35V
ZVS, GATE to GND LPWM Dimming Frequency 100Hz to 1KHz
CS to GND -0.3V to 7V HPWM Dimming Frequency 10KHz to 50KHz
Operating Ambient Temp. TA -40℃ ~ 85℃
Package Thermal Characteristics
Operating Junction Temp. TJ -40℃~ 150℃
Parameter RθJA (℃/W)
Min/Max Storage Temp. Tstg -55℃ ~150℃
SOP8 150
Lead Temp. (10 Sec) 260℃
Note: Stresses beyond those listed under “absolute maximum Ordering Information
ratings” may cause permanent damage to the device. These
are stress ratings only, functional operation of the device at
Part Number Description
these or any other conditions beyond those indicated under OB3375CP SOP8, Halogen-free in tube
“recommended operating conditions” is not implied. Exposure OB3375CPA SOP8, Halogen-free in T&R
to absolute maximum-rated conditions for extended periods
may affect device reliability.

Marking Information

OB3375 X X X

High performance Package

Package Halogen-free Packing
buck LED driver

C:SOP8 P:Halogen-free Blank:Tube

A: Taping

YWWZZZ
OB3375
Ps

Y:Year Code
WW:Week Code(01-52)
ZZZ:Lot Code
P:Halogen-free Package
s:Internal Code(Optional)

©On-Bright Electronics Confidential Preliminary Datasheet

OB_DOC_DS_337500
-2-
 OB3375
High performance buck LED driver

Terminal Assignments for SOP8 Package Parts

VIN 1 8 GATE

LPWM 2 7 GND
OB3375
HPWM 3 6 CS

FAULT 4 5 ZVS

Pin Num Pin Name I/O Description

1 VIN P Power supply input.
LPWM signal input pin for PWM dimming control and enable pin for
2 LPWM I/O
sleep mode control
3 HPWM I/O HPWM signal input pin for PWM to analog dimming control
4 FAULT I/O Fault signal for abnormal situation
5 ZVS I/O Quasi-Resonant signal
6 CS I/O Current sensing terminal.
7 GND P Power Ground.
8 GATE I/O Gate driver output

©On-Bright Electronics Confidential Preliminary Datasheet

OB_DOC_DS_337500
-3-
 OB3375
High performance buck LED driver

BLOCK DIAGRAM
VIN

UVLO Reference Vref

OTP

ZVS
zvs
detect

LPWM
Logic GATE
GATE
Control Driver
+

PWM

Soft

+
_
start Vth_ocp

CS
sense
High/low
Frequency
clamp Constant current CS
regulation

FAULT protection

HPWM GND

©On-Bright Electronics Confidential Preliminary Datasheet

OB_DOC_DS_337500
-4-
 OB3375
High performance buck LED driver

ELECTRICAL CHARACTERISTICS
VIN=12V,LPWM=5V, TA=25℃, if not otherwise noted.
Parameter Symbol Conditions Min Typical Max Units
Current Consumption
Input voltage range Vin 9 - 30 V
Vin=12V,LPWM=5V
Operating supply current 𝐼𝑉𝑉𝑉 - 1.1 1.3 mA
no load
LPWM low >50ms
Stand by current 𝐼𝑉𝑉𝑉_𝑠𝑠𝑠 - 20 30 uA
sleep mode
VIN UVLO
Vin under voltage lockout exit
UVLO(OFF) 7 8 9 V
(recovery)
Vin under voltage lockout
UVLO(ON) 6.2 7.2 8.2 V
enter
HPWM Section
HPWM(high) High Level 2 V
HPWM Logic input level
HPWM(low) Low Level 0.8 V
LPWM Control
LPWM(high) High Level 2.5 V
LPWM Input Threshold
LPWM(low) Low Level 1.3 V
Sleep mode time T_sleep 40 ms
Current Sense Input Section
Time of leading edge blanking 𝑇𝑙𝑙𝑙 250 350 450 ns
Threshold of over
𝑉𝑉ℎ𝑜𝑜𝑜 0.8 V
current protection
QR Section
Max frequency F max 200 230 260 KHz
Max gate off time Toff max 20 25 30 us
Max gate on time Ton max 20 25 30 us
Error Amplifier Section
Reference voltage of
Vth_ea 0.245 0.25 0.255 V
Error amplifier
Protection
Threshold of diode &
𝑉𝑉ℎ𝑐𝑐_ℎ𝑖𝑖ℎ1 1.5 V
Inductor short protection
Threshold of CS pin open
𝑉𝑉ℎ𝑐𝑐_ℎ𝑖𝑖ℎ2 2 V
protection
Temperature of thermal TOTP _ ON 150 ℃
shutdown
Temperature of thermal TOTP _ OFF 100 ℃
recovery
Gate Driver Output
Gate rise time Trise 1nF load - 150 ns
Gate fall time T fall 1nF load 30 ns

©On-Bright Electronics Confidential Preliminary Datasheet

OB_DOC_DS_337500
-5-
 OB3375
High performance buck LED driver

CHARACTERIZATION PLOTS
𝐼_𝑉𝑖𝑛(mA) vs Temperature 𝐼_(𝑉𝑖𝑛_𝑠𝑡𝑏)(uA) vs Temperature

2.000 50.00

𝐼_(𝑉𝑖𝑛_𝑠𝑡𝑏)(uA)
l𝐼_𝑉𝑖𝑛(mA)

1.600 40.00
1.200 30.00
0.800 20.00
0.400 10.00
0.000 0.00
-40 -10 20 50 80 110 140 -40 -10 20 50 80 110 140

Temperature(℃) Temperature(℃)

UVLO_OFF(V) vs Temperature UVLO_ON(V) vs Temperature

10.00 10.00
UVLO_OFF(V)

9.20 UVLO_ON(V) 9.00

8.40 8.00
7.60 7.00
6.80 6.00
6.00 5.00
-40 -10 20 50 80 110 140 -40 -10 20 50 80 110 140

Temperature(℃) Temperature(℃)

Ton_max(uS) vs Temperature Toff_max(uS) vs Temperature

50.00 50.00
Toff_max(uS)
Ton_max(uS)

40.00 40.00
30.00 30.00
20.00 20.00
10.00 10.00
0.00 0.00
-40 -10 20 50 80 110 140 -40 -10 20 50 80 110 140

Temperature(℃) Temperature(℃)

Vth_ea(V) vs Temperature

0.300
Vth_ea(mV)

0.250
0.200
0.150
0.100
-40 -10 20 50 80 110 140

Temperature(℃)

©On-Bright Electronics Confidential Preliminary Datasheet

OB_DOC_DS_337500
-6-
 OB3375
High performance buck LED driver

Function Description
General Operation The sensed error signal is amplified and
The OB3375 is a high efficiency LED driver compared to the CS pin sensing current signal to
designed for white LEDS and for large LCDS determine the on-time of the switching MOSFET.
backlight. OB3375 is built-in a quasi-resonant The error amplifier sources or sinks the current
control method buck DC/DC converter. The to the internal COMP to adjust the required
controller implements a peak current mode inductor current as the load changes.
control scheme and an internal The error amplifier reference is set by internal
transconductance amplifier to accurately control reference voltage and the duty cycle at HPWM
the output current over a wide input and load pin.
conditions. The transconductance amplifier The average LED current is approximated by the
reference is set by internal reference voltage and following equation；
the duty cycle at HPWM pin. 250 ∗ 𝐷𝐷𝐷𝐷𝐻𝐻𝐻𝐻 [𝑚𝑚]
𝐼𝐿𝐿𝐿 [𝑚𝑚] =
Low frequency LPWM dimming input that can 𝑅𝐶𝐶 [𝛺]
accept an external control signal with a duty ratio At light loading, the OB3375 automatically add
of 1%-100%. off time to improve efficiency and prevent
OB3375 offers comprehensive protection overcharging the output capacitor.
features to protect the system in various fault
Dimming Control
conditions such as Diode & Inductor short
The LED brightness is controlled by the PWM
protection, CS open protection, MOS DS short
signal at LPWM pin which has different duty
protection, LED+/LED- short protection,
cycle. OB3375 can accept an external PWM
LED-/GND short circuit protection, over
signal to LPWM pin in the range of 100Hz to 1
temperature protection (OTP). The
KHz with a swing voltage of 0V to a level greater
cycle-by-cycle current limit function limits the
than 2.5V.
maximum current flowing through the external
MOSFET. CS pin open Protection
OB3375 shuts down the output if CS pin is
Startup
floating. In case of CS pin floating, OB3375 will
OB3375 is enabled by applying a voltage of
pull up CS pin to internal 5V voltage. If the CS
greater than approximately 2.5V to LPWM pin.
voltage is greater than 2V (typical) at gate off
An on-chip internal 3.8M ohm pull down resistor
time, the gate output will be latched off for the
is inserted between LPWM pin and ground.
safe propose.
When the first rising edge is applied to LPWM
This protection is latched and can be reset from
input, the OB3375 will power up immediately,
VIN or LPWM.
and remains power up until the LPWM input is
lower than 1.3V for 40mS (typical), at this time LED+/LED- short & LED-/GND short
the chip will enter standby mode. At standby protection
mode, the power of the OB3375 will be lower When LED+/- short or LED- /GND short, IC can
than 20uA (typical). not detected demagnetization information ，
When LPWM is active high, The OB3375 will OB3375 will continuously work at max_off
check faults (UVLO, CS high, MOS ds short, state。After 60mS (typical), the gate output will
LED+/LED- short, LED-short to GND, OCP), if be latched off for the safe propose.
there is no fault, then the boost converter will This protection is latched and can be reset from
boost up the output with the internal soft start. VIN or LPWM.
UVLO Diode & Inductor Short Protection
An under-voltage lockout protection feature with When the diode or the inductor shorts, the
a hysteresis of about 800mv is provided for VIN. current of the power MOSFET increasing
When the voltage at this pin exceeds a threshold significantly. This state will cause the MOSFET
of approximately 8V (typ.), the IC starts normal permanent damage if the IC is continuously
operation. If the voltage at this pin drops below a working. OB3375 will monitor the voltage on CS
threshold of approximately 7.2V (typ.) , the IC pin voltage cycle by cycle. If the voltage on CS
stops switching operation. The IC resumes pin is greater than 1.5V (typical) for continuous
switching operation when the voltage at pin VIN 16 cycles, the IC will latch shutdown the gate
increases to a voltage above 8V (typical). output to prevent the MOSFET from permanent
LED Current Regulation damage.
The LED current is sensed by current sense This protection is latched and can be reset from
resistors connected between pin CS and GND VIN or LPWM.

©On-Bright Electronics Confidential Preliminary Datasheet

OB_DOC_DS_337500
-7-
 OB3375
High performance buck LED driver

MOS drain source Short Protection logic level signal at FAULT pin. The output
The OB3375 has power MOS source drain stage of the FAULT pin adopts an open-drain
short protection, when power MOS source drain NMOS structure. When OB3375 is operating
short, the OB3375 will monitor the CS voltage normally, the voltage at FAULT pin is
greater than 2V at gate off time or CS voltage pulled-high through external circuits. When
greater than 0.25V continuous 50uS. The there is any error condition occurs, the voltage
gate output will be latched off for the safe at FAULT pin is pulled-low. The FAULT pin
propose. indicates the following seven conditions:
This protection is latched and can be reset from  CS Open
VIN or LPWM.  Diode & Inductor Short
Thermal Shutdown  LED +/LED- short
The OB3375 includes a thermal protection circuit.  Power MOS drain source short
When the junction temperature exceeds 150°C  LED-/ GND short
(typical), the controller and current sources shut  LED open
down and do not restart until the junction
temperature drops below 100°C (typical).
Indication for FAULT Condition
OB3375 builds an FAULT condition to output a

©On-Bright Electronics Confidential Preliminary Datasheet

OB_DOC_DS_337500
-8-
 OB3375
High performance buck LED driver

PACKAGE MECHANICAL DATA

SOP8

Dimensions In Millimeters Dimensions In Inches

Symbol
Min Max Min Max
A 1.350 1.750 0.053 0.069
A1 0.050 0.250 0.002 0.010
A2 1.250 1.650 0.049 0.065
b 0.310 0.510 0.012 0.020
c 0.100 0.250 0.004 0.010
D 4.700 5.150 0.185 0.203
E 3.800 4.000 0.150 0.157
E1 5.800 6.200 0.228 0.244
e 1.270 (BSC) 0.050 (BSC)
L 0.400 1.270 0.016 0.050
θ 0º 8º 0º 8º

©On-Bright Electronics Confidential Preliminary Datasheet

OB_DOC_DS_337500
-9-
 OB3375
High performance buck LED driver

IMPORTANT NOTICE
RIGHT TO MAKE CHANGES
On-Bright Electronics Corp. reserves the right to make corrections, modifications, enhancements,
improvements and other changes to its products and services at any time and to discontinue any product
or service without notice. Customers should obtain the latest relevant information before placing orders
and should verify that such information is current and complete.

WARRANTY INFORMATION
On-Bright Electronics Corp. warrants performance of its hardware products to the specifications applicable
at the time of sale in accordance with its standard warranty. Testing and other quality control techniques
are used to the extent it deems necessary to support this warranty. Except where mandated by
government requirements, testing of all parameters of each product is not necessarily performed.
On-Bright Electronics Corp. assumes no liability for application assistance or customer product design.
Customers are responsible for their products and applications using On-Bright’s components, data sheet
and application notes. To minimize the risks associated with customer products and applications,
customers should provide adequate design and operating safeguards.

LIFE SUPPORT
On-Bright Electronics Corp.’s products are not designed to be used as components in devices intended to
support or sustain human life. On-bright Electronics Corp. will not be held liable for any damages or claims
resulting from the use of its products in medical applications.

MILITARY
On-Bright Electronics Corp.’s products are not designed for use in military applications. On-Bright
Electronics Corp. will not be held liable for any damages or claims resulting from the use of its products in
military applications.

©On-Bright Electronics Confidential Preliminary Datasheet

OB_DOC_DS_337500
- 10 -