dmc sd 10
wide belt sanders
automatic wide belt sanders
dmc sd 10
automatic wide belt sanders
EVERYTHING
YOU NEED
WITH NO
COMPROMISES
1
dmc sd 10
automatic wide belt sanders
SOLID FLEXIBLE COMPACT READY EFFICIENT
Sturdy and ergonomic steel main frame to One unit, three possible configurations Reduced dimensions and no obstacles on Only half-day to be operative Oscillating blowers to minimise
satisfy all requirements thanks to the on/off function on CS unit the ground for the best space optimization compressed air consumption
Up to 11 kW power for excellent calibrating
2 3
sd 10
dmc sd 10
TECHNICAL FEATURES
automatic wide belt sanders
TECHNOLOGICAL ADVANTAGES Timed oscillating blowers enable
to minimise compressed air
consumption guaranteeing
reliability over time
Motorised belt conveyor
positioning, with digital
readout of working thickness
The out-feed pressure
roller allows a uniform
and intense pressure
in calibrating with high
removal and sanding of
short and narrow pieces
Pre-loading indicators
grant a better positioning
of the combined unit,
thus obtaining an
impeccable finishing
Electronic positioning “Hand-safety” device to
device for a precise offer the best and safest Exhaust hood for the
and fast working working conditions dust dispersion control
table opening during processing
In-feed idle roller conveyor permits Semi-stiff flat pad Rapid and precise
to resist heavy working loads for veneered locking system of the
panels sanding working unit
4 5
OWING TO THE dmc sd 10
automatic wide belt sanders
STURDINESS
OF THE STRUCTURE, Basis version
IT IS POSSIBLE TO SET CS 95
THE EXACT POWER FOR • Combined-unit equipped with:
HEAVY REMOVALS
- 85 sh rubber coated calibrating roller
- stiff sanding pad
Standard equipment
• Powered worktable positioning
• Digital readout of working thickness
• Rubber-coated-floating rollers at the infeed and outfeed operating unit
• Electronic oscillating of sanding belt
• Direct start main motor
• Feed belt speed with 2-speeds variable feed motor
1668
Main options
• Semi-stiff pad
• Grooved steel calibrating roller
• Pneumatic roller and pad control On/off
• Powered main motor
• Automatic star-delta start of the main motor
• Automatic feed conveyor centering
• Oscillating blower for sanding belt cleaning
• Electronic positioning of the working table
• Automatic pad operation
Technical features
• No. 2 infeed and outfeed support table rollers on the feed belt
Working width mm 950
Min/max machining thickness mm 4-170
Sanding belt width mm 970
Abrasive belts length mm 1525
Standard main motor power kw (HP) 5,5 (7,5) The technical data can vary according to the requested machine composition. In this catalogue,
machines are shown with options. The company reserves the right to modify technical
Standard feed belt speed m/min 4,5/9 specifications without prior notice; the modifications do not influence the safety foreseen
by the CE Norms.
Compressed air consumption (at 6 bar) Nl/min 20(*) (*) for machine without oscillating
blower
Inlet air consumption (at 22 m/sec) m3/h 1220 Noise levels according to the reference standard EN ISO 11202:2010 and EN ISO 3746:2010
6 7
ONE TOOL, dmc sd 10
automatic wide belt sanders
THREE OPTIONS
Precision in calibrating and quality RA – STEEL ROLLER
in sanding solid and veneered panels This is the ideal solution for calibrating with
provide higher finishing performance large-scale chip removal even on wood with a
compared to the market offer. differentiated grain and knotted solid wood.
This doesn’t require any maintenance.
PAD WITH GLUED GRAPHITE CLOTH
Depending on the machining, it is possible to
get as a standard equipment the TRP/I stiff
pad for solid wood processing, or the TSP/I
semi-stiff pad for veneered panel sanding.
AUTOMATIC ANTI-DUBBING DEVICE
The electronic timer synchronizes the pad
intervention with two standard feed belt
speeds. This allows to avoid the bevel of the
front or rear corner of veneered panels.
8 9
SMALL BODY, BIG dmc sd 10
automatic wide belt sanders
SOUL DUE TO
THE ENRICHED
TECHNOLOGICAL
FEATURES
AUTOMATIC BELT CENTERING
The automatic system allows joiners to be mostly
effective and, consequently, to be more profitable.
AUTOMATIC UNITS POSITIONING AUTOMATIC FEED CONVEYOR CENTERING
A strong pneumatic cylinder allows to connect/disconnect The pneumatic device maintains the conveyor belt
the operating units directly from the control panel, constantly centered on the feed rollers, with no regulation ELECTRONIC WORKING THICKNESS POSITIONING
maintaining the decimal regulation of working position. needed by the operator. It allows the panel thickness detection with high
precision. This device is equipped with a decimal
adjustment system which automatically sets the stock
removal.
OSCILLATING BELT CLEANING BLOWER
Allows to increase the blowers longlasting, improving,
at the same time, the finishing quality.
10 11
DMC SD 10 COMPACTNESS THE STRONGEST
ALLOWS THE JOINER WOOD TECHNOLOGIES
TO EASILY POSITION
THE MACHINE INSIDE ARE IN OUR DNA
HIS WORKSHOP, SCM. A HERITAGE OF SKILLS IN A UNIQUE BRAND
Over 65 years of success gives SCM the centre stage in woodworking
OPTIMISING HIS
technology. This heritage results from bringing together the best know-how in
machining and systems for wood-based manufacturing. SCM is present all over
the world, brought to you by the widest distribution network in the industry.
WORK SPACE
No floor obstructions, for greater work freedom.
65 years history
3 main production sites in Italy
300.000 square metres of production space
17.000 machines manufactured per year
90% export
20 foreign branches
350 agents and dealers
500 support technicians
500 registered patents
In SCM’s DNA also strength and solidity of a great Group. The SCM Group is a world leader, manufacturing industrial
equipment and components for machining the widest range of materials.
SCM GROUP, A HIGHLY SKILLED TEAM EXPERT
IN INDUSTRIAL MACHINES AND COMPONENTS
INDUSTRIAL MACHINERY INDUSTRIAL COMPONENTS
Stand-alone machines, integrated systems and services Technological components for the Group’s machines and systems,
dedicated to processing a wide range of materials. for those of third-parties and the machinery industry.
WOODWORKING TECHNOLOGIES TECHNOLOGIES FOR PROCESSING SPINDLES AND ELECTRIC PANELS METALWORK CAST IRON
COMPOSITE MATERIALS, ALUMINIUM, TECHNOLOGICAL
PLASTIC, GLASS, STONE, METAL COMPONENTS
12
REV. N. 00 - 06.2018
SCM GROUP SPA
via Casale 450 - 47826 Villa Verucchio, Rimini - Italy
tel. +39 0541 674111 - fax +39 0541 674274
dmc@[Link]
[Link]
