CABLE TRUNKING
The metal cable trunking manufactured by SAN solve a variety of commercial
and industrial cable support needs regardless of the environment.
Manufactured from carbon steel, finished with either hot dip galvanized or
powder coating after fabrication the cable trunking is resistant to harsh solid
and performant environments.
SAN cable trunking products are ideal for all types of industrial applications,
even in special conditions like high concentrations of humidity or salinity, where
acids are used and when large quantities of cables are required (in the fields
petrochemical and iron and steel industries, power stations and underground or
maritime installations). SAN’s cable support systems are strong and perfectly fit
for the most complex applications. SAN cable trunking products are easy to
mount, practical, safe and equipped with snap-on covers, the new cable trays
can be fastened to the ceiling or to the wall, making it possible, thanks to the
wide range of trunking, corners, reducers and accessories, to satisfy all trunking
requirements without any problems.
Closed/punched base cable trays, along with SAN’s cable ladders, and trunking
systems, hot dip Galvanized or powder coating after production, make SAN metal
trunking systems the answer to all requirements, in any kind of application
context.
2
CABLE TRUNKING -
Earth bonding
Cable trunking and ducting systems are designed to carry single insulated
cables, and such systems must therefore provide the secondary protection
required by the Wiring Regulations. This means trunking and ducting systems
must be earth bonded together, and then connected to a suitable earth point.
SAN Engineering trunking is designed to provide such earth bonding, provided
that the system is fully assembled with all manufacturer’s original components,
including fixings, and that all fixings are fully tightened. This is achieved by a
combination of serrations under the head of the fixing screws and the internal
barbs on the fixing bars.
Electromagnetic Compatibility (EMC)
Cable trunking and ducting systems are considered passive under normal
conditions in respect of electromagnetic influences. The installation of current
carrying cables may cause emissions and these cables may also be influenced
by electromagnetic signals from elsewhere, but the degree of influence will
depend on the nature of the installation and the apparatus connected to the
system. Specific information relating to the details of cable separation required
according to the type of signal, and further information about EMC, is provided in
the relevant Standards and Regulations. However as a basic principle, if power
and signal cables are run in separate compartments of a metal trunking system,
then the metal segregation will significantly reduce the possibility of one circuit
having undesirable effect influence upon another.
Supporting Cable Trunking Systems
The connector between all types of cable trunking lengths is to provide
electrical and mechanical connection between the lengths; it does not provide a
load bearing connection between lengths. Consequently each length must be
fully supported so that there is no significant bending force applied to the
connector.
Each individual length of trunking is strong enough to carry the maximum
number of cables that can be physically fitted into the trunking whilst still being
able to correctly fit the cover without applying force. All supports must therefore
be designed to carry each length individually without relying on the connector.
3
CABLE TRUNKING SYSTEMS – LAYOUT
❑ Elbow 45
❑ Elbow 90
❑ Straight Reducer
❑ Straight Trunking
❑ Equal Tee
❑ Equal Cross
❑ 90 Bend Inside Cover
4
CABLE TRUNKING SYSTEMS
❑ Materials : Milld Steel, Stainless Steel, GI, Aluminum, EG.
❑ Thickness is minimum recommended as per SAN manufacturing standard.
❑ Heights available are standard, other heights are available as special request.
❑ Standard Couplers size is 100mm x side height of Trunking.
❑ Standard Hardware M6 Bolts for Cable Tray with M6 Nuts and Washer.
❑ Cable Trunking Length is SAN manufacturing standard; other Lengths can be provided upon request.
❑ Finishing Standards available : Hot Dip Galvanized / G.I / Epoxy Powder Coating.
Cable Trunking Straight (S T N )
Cable Trunking Straight (D T N )
5
CABLE TRUNKING SYSTEMS
Cable Trunking Straight (M T N )
6
CABLE TRUNKING SYSTEMS
Cable Trunking – Outdoor Application
Cable Trunking – Indoor Application
7
CABLE TRUNKING SYSTEMS – Fittings
Elbow 900
Elbow 450
Equal Cross
Equal Tee
8
CABLE TRUNKING SYSTEMS – Fittings
Elbow 900 Top Cover
Elbow 900 Outside Cover
Left Side / Right Side - Reducer
9
PRODUCT COATING
SAN Engineering offers best quality of its finished products, offering better
services to our clients globally. The 2 types of finishing available are
* Hot Dip Galvanization (HDG)
** EPOXY Powder Coating
HOT-DIP GALVANIZATION
EPOXY POWDER COATING
10
CABLE TRUNKING SYSTEMS – Quality Control
11
Address :
A-5-10, Empire Tower No. 8, Jalan 25/102A, Taman +603 5033 1741
SS16/1, 47500 Sri Muda, Seksyen 25, +603 5033 1742
Subang Jaya, 40400 Shah Alam, +6012 617 2936 (Akilan)
Selangor Darul Ehsan, Selangor Darul Ehsan, +6016 212 6740 (Norisz)
Malaysia Malaysia enquiry@[Link]
12
