D.

Instruction
Function Range Resolution Accuracy [Link] Other
A. Overview 600.0Ω 0.1Ω (1) Panel Description (refer to the image on the right)
The ZT-102L is a battery-powered digital multimeter with true RMS and auto- 1. LCD Display: Displays the measured values and units.
6.000kΩ 0.001kΩ
2. Function Keys
ranging capabilities. In addition to the standard multimeter functions, it also features 60.00kΩ 0.01kΩ ±(0.5%+3) Disables input voltage
Resistance 60MΩ 2a. "HOLD" Key: Press this key to freeze the current reading,
inductance measurement. The instrument has a 6000-count display, an LCD screen 600.0kΩ 0.1kΩ in this mode
and the screen will display the "HOLD" symbol. Press again to
with backlight for clear readings.. 6.000MΩ 0.001MΩ exit the hold state. To activate the backlight, press and hold 1
60.00MΩ 0.01MΩ ±(1.5%+3) this key for more than 2 seconds, and press again to turn off
B. Safety Information 6.000nF 0.001nF ±(5.0%+20) the backlight.
To prevent possible electric shock, fire, or personal injury, please read the safety 60.00nF 0.01nF 2b. "SELECT" Key: Press this key to toggle between AC/DC 2
precautions before use. 600.0nF 0.1nF voltage, diode/resistance/continuity, or ℃/℉ ranges.
(1) During measurement, do not exceed the "Technical Specifications" maximum 6.000μF 0.001μF ±(2.0%+5) Disables input voltage 3. Rotary Switch: Used to change the measurement function
Capacitance 60.00mF
measurement value. 60.00μF 0.01μF in this mode and range. 3
(2) Voltages below 36V are considered safe. When measuring DC voltage above 36V 600.0μF 0.1μF (Starting from OFF and rotating clockwise)
or AC voltage above 25V, ensure that the test leads have reliable contact, correct 6.000mF 0.001mF 3a. OFF Position: Power-off mode.
±(5.0%+5) 3b. AC/DC Voltage(V)/Frequency/Duty Cycle Range (referred
connections, and good insulation to avoid electric shock. 60.00mF 0.01mF
99.99Hz 0.01Hz to as voltage range).
(3) When changing functions or ranges, the test leads should be removed from the
999.9Hz 0.1Hz 3c. AC/DC Millivolt Voltage(mV)/Frequency/Duty Cycle Range
test points. (referred to as small voltage range).
ZT-102L Digital Multimeter User (4) Select the correct function and range; an over-range measurement will display
"OL."
Frequency
9.999kHz
99.99kHz
0.001kHz
0.01kHz
±(0.1%+2) 9.999MHz [Link]/Continuity/Diode/Capacitance Range (referred 6 4
to as resistance range).
Manual (5) Safety symbol explanation:
999.9kHz
9.999MHz
0.1kHz
0.001MHz
3e. Non-Contact Voltage Detection Range (NCV).
Hazardous Voltage Earth 3f. Inductance Range (L).
6.000mH 0.001mH ±(5%+50)
Double Insulated Low Battery 3g. AC/DC Current (A) Range (referred to as current range).
60.00mH 0.01mH 3h. AC/DC Current (mA) Range (referred to as small current 5
Risk of Danger. Check the User Manual. Disables input voltage
Inductance 600.0mH 0.1mH ±(3%+10) 60.00H range).
in this mode
C. Specifications 6.000H 0.001H 4. VΩHz: Input terminal for voltage, resistance, capacitance, inductance, frequency,
Electrical Specifications 60.00H 0.01H ±(5%+50) temperature, current (mA), continuity, diode, and duty cycle measurements.
Function Range Resolution Accuracy [Link] Other Duty Cycle 1%~99% 0.1% ±(0.1%+2) 5. COM: Common terminal for all measurements.
6.000V 0.001V Diode √(DC forward current is 5mA，voltage is 3.9V） 6. 10A: Input terminal for current (A) measurements.
DC Voltage 60.00V 0.01V Disables input
1000V Continuity √(no more than 50Ω) （2）Voltage Measurement
（V） 600.0V 0.1V voltage in this
±(0.5%+3) Input Resistance:10MΩ (-20~1000)℃ 1℃ 1000℃
1000V 1V Temperature ±(2.5%+5） mode 1. Insert the black test lead into the "COM" jack and the red test lead into the "VΩHz"
(-4~1832)℉ 1℉ 1832℉
DC Voltage 60.00mV 0.01mV jack.
600mV General Specifications Mechanical Specifications
（mV） 600.0mV 0.1mV Dimension 130*65*32mm 2. Turn the knob switch to the voltage range or millivolt voltage range.
LCD Display 6000 counts
6.000V 0.001V Weight 130g(battery included)
Measurement Range Auto
AC Voltage 60.00V 0.01V Input Resistance:10MΩ Battery Type 1.5V AAA Battery * 2 3. Press the SELECT key to toggle between AC and DC voltage measurement.
750V Material ABS
（V） 600.0V 0.1V （600mV range, ＞60MΩ） Warranty One years
±(1.0%+3) Sampling Rate 3 times/second 4. Touch the test leads to the correct test points on the circuit.
750V 1V Frequency Response: Environmental Specifications
AC Voltage 60.00mV 0.01mV 40Hz-1kHz Ture RMS √ 5. Read the displayed voltage value on the screen.
Operating Temperature 0~40℃
600mV Data Hold √
（mV） 600.0mV 0.1mV Environment Humidity ＜75%
DC Current 6.000A 0.001A Screen Backlight √ *Attention:
Storage Temperature -20~60℃
10A Low Battery Indication √
（A） 10.00A 0.01A [Link]：10A（no Environment Humidity ＜80% a. The measured voltage must not exceed the rated maximum test value, as it may
±(1.2%+3) Auto Power Off √
DC Current 60.00mA 0.01mA more than 15 seconds） damage the instrument and pose a risk to personal safety.
600mA
（mA） 600.0mA 0.1mA No Voltage input at this Safety Specifications
AC Current 6.000A 0.001A mode b. When measuring high-voltage circuits, avoid touching the high-voltage components.
EN 61010-1: 2010; EN 61326-1: 2013; FCC Part 15 Subpart B: 2016
10A
（A） 10.00A 0.01A Frequency Response(AC): Standard Accessories
±(1.5%+3)
AC Current 60.00mA 0.01mA 40Hz-1kHz Battery * 2pcs; Test Lead * 1 pair; Drawstring Pouch * 1pc
600mA
（mA） 600.0mA 0.1mA TP01K thermocouple probe * 1pc ; English User Manual; Gift Box
-1- -2- -3- -4-
(3) Current Measurement 4, Read the forward voltage displayed on the screen.; (11) Auto Power Off F. Troubleshooting
1. Insert the black test lead into the "COM" jack, and the red test lead into the "VΩHz" jack 5. If the test lead polarity is reversed or the diode is faulty, the screen will display "OL." 1. If the instrument is not used for 15 minutes, it will automatically power off. If your instrument is not functioning properly, the following methods can help you
(for maximum test value of 600mA) or the "10A" jack (for maximum test value of 10A). *Attention: 2. One minute before powering off, the built-in buzzer will emit five beeps as a quickly resolve common issues. If the problem persists and cannot be resolved, please
2. Turn the knob switch to the current range or small current range. a. Inputting voltage in the diode range is strictly prohibited. reminder. contact the maintenance center or the distributor for assistance.
3. Press the SELECT key to toggle between AC and DC current measurement. b. Before testing, disconnect the circuit's power supply and discharge all high-voltage 3. To restart the instrument after auto power off, simply press the SELECT key to
4. Disconnect the circuit path to be tested, connect the test leads in series with the circuit, turn on the power. Fault Phenomenon Inspection Area and Method
capacitors.
and apply power to the circuit. 4. If you wish to disable the auto power off function, hold down the SELECT key
(7) Capacitance Measurement while turning on the instrument. The buzzer will emit four beeps, indicating that Display screen not Power not connected; Replace battery
5. Read the displayed current value on the screen. showing
1. Insert the black test lead into the "COM" jack and the red test lead into the "VΩHz" the auto power off has been canceled.
* Attention: jack. E. Maintenance and Care Symbol appearing Replace battery
a. The measured current must not exceed the rated maximum test value, as it may damage 2. Turn the knob switch to the resistance range, and press the SELECT key three times Except for battery and fuse replacement, please do not attempt to repair this
the instrument and pose a risk to personal safety. to switch to the capacitance range. product or modify the circuit unless you have the required qualifications and possess No current input Replace fuse
b. If the magnitude of the current to be measured is unknown, perform a preliminary test 3. Connect the red test lead to the positive terminal of the capacitor to be tested, and the appropriate calibration, performance testing, and maintenance operation
using the 10A jack and then select the appropriate range based on the displayed value. the black test lead to the negative terminal. instructions.
Under the current measurement mode, it is strictly prohibited to input voltages higher 4. . After the reading stabilizes, read the displayed capacitance value on the screen.. (1) This product should not be stored or used in high-temperature, high-humidity, Limited Warranty and Scope of Responsibilities
than 36V DC or 25V AC peak. * Attention : flammable, explosive, or strong magnetic field environments.
Before testing, disconnect the circuit's power supply and discharge all high-voltage (2) Use a damp cloth and mild cleaning agent to clean the casing; do not use From the date of purchase, this product is eligible for a one-year warranty
(4) Resistance Measurement capacitors. corrosive agents or solvents. service. However, this warranty does not cover fuses (blown), disposable
1. Insert the black test lead into the "COM" jack and the red test lead into the "VΩHz" (3) Before cleaning the product, ensure to clear the input signal first. batteries (used up), or damages resulting from accidents, negligence, misuse,
jack. (8) Frequency and Duty Cycle Measurement (4) If not in use for an extended period, remove the battery to prevent battery modification, contamination, or abnormal operating environments.
2. Turn the knob switch to the resistance range, and the screen will display "OL" by 1. Insert the black test lead into the "COM" jack and the red test lead into the "VΩHz" leakage and corrosion of the instrument.
default. jack. (5) Pay attention to battery usage; when the display shows the " " symbol,
2. Turn the knob switch to the frequency range, and press the SELECT key again to Any changes to this user manual will not be separately notified;
3. Touch the test leads to the desired circuit test points.; replace the battery following these steps:
measure the duty cycle if needed. The contents of this user manual are believed to be accurate. If users find any
4. Read the displayed resistance value on the screen. 1Unscrew the screw holding the battery in place on the back cover, and open
3. Touch the test leads to the desired circuit test points.; the battery compartment door; errors, omissions, etc., please contact the manufacturer;
* Attention: 4. Read the displayed frequency/duty cycle value on the screen. The company is not liable for accidents and hazards caused by user errors in
a. Before measuring live resistance, ensure that all power sources in the tested circuit 2Remove the old battery and replace it with two new batteries of the same
* Attention : type.; operation;
are turned off, and all capacitors are completely discharged. a. The frequency range is suitable for measuring high frequencies and low voltages. The functions described in this user manual should not be considered as reasons
b. Inputting voltage in the resistance range is strictly prohibited. 3. Close the battery compartment door and tighten the screw.
(9) Temperature Measurement (6) When replacing the fuse, use a fuse of the same specification and model. to use the product for special purposes.
(5) Continuity Measurement 1. Insert the black plug of the thermocouple into the "COM" jack and the red plug Follow the same steps as in (5).
1. Insert the black test lead into the "COM" jack and the red test lead into the "VΩHz" into the "VΩHz" jack.
jack. 2. Turn the knob switch to the temperature range, and the screen will display the
2. Turn the knob switch to the resistance range, and press the SELECT key once to Warning：
room temperature by default. Press the SELECT key to switch between ℃/℉.
switch to the continuity range. 3. Place the temperature sensor of the thermocouple in the temperature field to be 1. Do NOT exceed the “maximum value” indicated in the Specification;
3. Touch the test leads to the two points of the circuit to be tested. measured. 2. Do not measure voltage in current、 resistance、 diode、 continuity、
4. If the resistance value is less than 50Ω, the buzzer will sound, indicating a short 4. Read the displayed temperature value on the screen. temperature or inductance mode.
circuit. * Attention : 3. Do not use this instrument when the battery is not installed or the back cover
*Attention: a. Inputting voltage in the temperature range is strictly prohibited. is not securely closed.
a. Inputting voltage in the continuity range is strictly prohibited. 4. Before replacing the battery or fuse, remove the test leads from the test
(10) Inductance Measuring points and turn off the instrument.
(6) Diode Measurement 1. Insert the black test lead into the "COM" terminal and the red test lead into the
1, Insert the black test lead into the "COM" jack and the red test lead into the "VΩHz" "VΩHz" terminal.
jack. 2. Turn the knob switch to the "L" (inductance) position.
2. Turn the knob switch to the resistance range, and press the SELECT key twice to 3. Use the red and black test leads to probe the two terminals of the inductor to be
switch to the diode range. measured. The instrument will automatically select the appropriate range based on
3. Connect the red test lead to the positive terminal of the diode to be tested, and the the inductance value.
black test lead to the negative terminal. 4. After the reading stabilizes, read the inductance value displayed on the screen.
-5- -6- -7- -8-