Scribd
Upload
81 views1 page

SILIKAL® R 17 Application Guide

SILIKAL® R 17 is a reactive resin mortar designed for concrete repairs and screed, featuring high compressive strength (75 N/mm²) and good self-leveling properties. It is suitable for both indoor and outdoor applications, with a processing time of 15 minutes and a minimum layer thickness of 6 mm. The product requires specific mixing instructions and can be used within a temperature range of -10 °C to +35 °C.

Uploaded by

hockeay123
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
81 views1 page

SILIKAL® R 17 Application Guide

SILIKAL® R 17 is a reactive resin mortar designed for concrete repairs and screed, featuring high compressive strength (75 N/mm²) and good self-leveling properties. It is suitable for both indoor and outdoor applications, with a processing time of 15 minutes and a minimum layer thickness of 6 mm. The product requires specific mixing instructions and can be used within a temperature range of -10 °C to +35 °C.

Uploaded by

hockeay123
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd

SILIKAL® R 17

Product information

Reactive resin mortar for concrete repairs and screed

Properties Area of application


– High compressive strength (75 N/mm²) – Reactive resin mortar indoors and outdoors
– High tensile strength in bending (17 N/mm²)
– Low shrinkage
– Wear-resistant
– Good self levelling properties
– Processing time / hardening time at +20 °C: 15 min / 1 h

Guide for application and calculation


SILIKAL® R 17 Amount Quantity in ltr. Quantity in ltr. Minimum layer
in kg fixed volume thickness in mm
a) SILIKAL® R 17 Powder 15.00 11.50
SILIKAL® R 17 Hardener 1.85 2.00 8.50 6
16.85
b) SILIKAL® R 17 Powder 15.00 11.50
SILIKAL® R 17 Hardener 1.85 2.00
11.60 25
SILIKAL® Filler QS 2 – 8 mm 8.00 5.00
24.85
c) SILIKAL® R 17 Powder 15.00 11.50
SILIKAL® R 17 Hardener 1.85 2.00
SILIKAL® Filler QS 2 – 8 mm 3.00 1.90 14.25 50
SILIKAL® Filler QS 8 – 16 mm 12.00 7.50
31.85

Advice on application
– First add hardener liquid, then slowly stir in the powder component, then (as required) add SILIKAL® Filler QS and stir for
roughly 2 minutes until an homogeneous mortar is created, then use immediately.
– The minimum layer thickness is 6 mm – not extendable to zero.
– Do not use any fillers other than those named in the table “Guide for application and calculation”.
– Note: If priming must be performed at temperatures between -11 °C and -25 °C, the special product SILIKAL® R 51 (-25 °C)
can be used (data sheet on request).

Characteristics as delivered
Property Approx. value
Viscosity, +20 °C 1 mPa · s
Density, +20 °C 0.93 g/cm3
Application temperature -10 °C to +35 °C

CE marking

05
SILIKAL GmbH
Ostring 23 · 63533 Mainhausen
DOP: [Link]
R17-001
EN 13813:2002
SR–C70–F15–B2,0–IR4–AR0,5–Bfl-s1
Synthetic resin screed
for application in buildings
Flexural strength > 17 N/mm2
Compressive strength > 75 N/mm2
Bond strength B 2.0
Impact resistance IR 0.4
Reaction to fire Bfl-s1

Other applicable documents


SILIKAL® Filler QS Data sheet FQS The information in this data sheet replaces all previous information about the product
and its application. The application instructions as well as the technical data of the
General notes Technical documentation MMA product are only guidelines. The buyer is responsible for the application and claims of
Safety data sheets All used Silikal products third parties.

Silikal Product Iinformation Silikal GmbH


Data sheet SILIKAL® R 17 Ostring 23 · 63533 Mainhausen · Germany
Page 1 of 1 Phone: +49 (0) 61 82 / 92 35-0
94 Issue MMA 7.02A – February 2023 mail@[Link] · [Link]

You might also like