NSK ELECTRONICS
8051 DEVELOPMENT BOARD
R1
2021
POWER OF
IMAGINATION
[Link]/com
8051 DEVELOPMENT BOARD R1 2021
The 8051 Development Board R1 is specifically designed to help the students and
learners for those who are starting in the area of Embedded systems. Basic 8051 microcontroller
families like Atmel, Philips, Nuvoton and SST as well as designing and testing your applications
in real-time. The main feature of this board is you can easily interface with PC and can also
download the hex file into the microcontroller on the board via USB & RS232 port. Flashing a
program 8051 microcontrollers like PHILIPS, NUVOTON, SST through software Flash Magic,
Nuvoton Flasher, SST Flasher respectively.
Key Features:
40-pin IC base for MCU
Operating Frequency: 11.0592 MHz crystal
32 I/O Pins for 8051
8 Push Buttons
4x4 Matrix Keypad
EEPROM 24Cxx Memory
Buzzer
8 No`s of LEDs
On Board Power Supply (12V, 5V, GND)
ULN2803A
Relay
ADC PCF8591
Serial 232 Port (Serial Communication)
USB Port (Serial Communication)
DS1307 RTC
L293D (Motor Drive)
16X2 LCD display
7 Segment Display
ISP programming
[Link]/com Page 2
8051 DEVELOPMENT BOARD R1 2021
FIGURE:
12 11 10 9
13
8
6
14
5
15
4
16
3
17
2
18
19 20 21 22
[Link]/com Page 3
8051 DEVELOPMENT BOARD R1 2021
FIGURE SPECIFICATIONS
1. DC JACK
2. DC JACK JUMPER
3. ON BOARD POWER SUPPLY
4. ULN2803A
5. ISP CONNECTOR
6. RELAY
7. RESET SWITCH
8. L293D
9. 16x2 LCD DISPLAY
10. RTC DS1307
11. RTC BATTERY SOCKET
12. 4 SEVEN SEGMENT
13. USB PORT
14. RS232 PORT
15. MICROCONTROLLER
16. ADC PCF8591
17. IO PINS
18. SWITCHES
19. EEPROM 24CXX
20. BUZZER
21. 4X4 KEYPAD
22. 8No`s LEDS
While executing the sections jumper required as per your applications.
Package Contents
1) Software CD (Flash Magic, Data Sheet, Example Programs, Manual, KEIL Eva).
2) 8051 Development Board (WITH CHIPS 8051 IC, MAX232, RTC1307, I2C24Cxx,
ULN2803, L293D, ADC PCF8591P & 16x2 LCD).
3) USB Cable.
[Link]/com Page 4
8051 DEVELOPMENT BOARD R1 2021
1. POWER SUPPLY
JUMPER
PLUG-IN ADAPTER
Connect Jumper then Plug-in adapter 12V.
On Board Power supplies 12V, 5V, GND.
2. MICROCONTROLLER SECTION
MICROCONTROLLER
ISP CONNECTOR
4 Ports / 32 I/O Pins.
ISP Connector for Programming purpose.
Port Pin I/O can used external devices.
[Link]/com Page 5
8051 DEVELOPMENT BOARD R1 2021
3. 4X4 MATRIX KEYPAD AND 8 SWITCHES
While using 4x4 Matrix Keypad or 8 Switches connect jumper Port2.0 to Port2.7
as per your requirements.
4. ULN 2803 SECTION
The ULN2803A provides 8 Darlington transistors with common emitter
configuration.
To drive motors and relays in this output section.
The output current to 500mA.
Connect jumper Port0.0 to Port0.7
5. RELAY SECTION
The Relay has NO-COM-NC.
NO
Connect Jumper P3.4
Relay Output connect to your as per applications.
[Link]/com Page 6
8051 DEVELOPMENT BOARD R1 2021
6. L293D SECTION
Connect Jumper Port1.0 to Port1.5
The L293D provides 4 high current outputs. (M1, M2).
To drive loads like Solenoids, DC Motors, Stepper Motor.
The output current to 600mA.
Motor connects to M1, M2 terminal block.
7. LCD DISPLAY
Connect jumpers Port0.6,07 and Port1.0 to Port1.7
As per requirements by giving LCD Commands you can display any character or
name. (Refer LCD Commands).
The Potentiometer
tentiometer 10k used to adjusting the LCD contrast.
[Link]/com Page 7
8051 DEVELOPMENT BOARD R1 2021
8. 7 SEGMENT DISPLAY
.
The four Seven segment can be used to display the numbers and hexadecimal
values to microcontroller.
Main feature is Multiplexing.
9. USB PORT / RS232 PORT
Used for Serial Communication.
Flashing the program through USB Port/ Serial Port.
10. RTC DS1307 SECTION
Connect jumper Port3.6 and Port3.7
CMOS Battery used for backup supply in proper timing operation.
[Link]/com Page 8
8051 DEVELOPMENT BOARD R1 2021
11. ADC SECTION
PCF8591 is a 8 bit A/D and D/A converter based on I2C bus.
4 Analog Inputs.
Flash the hex file into the microcontroller.
Connect Jumper and varying pot Digital output shown in LCD Display.
12. EEPROM 24CXX SECTION
Connect jumper Port3.6 and Port3.7
To read and write the data in EEPROM memory.
13. ONBOARD POWER SUPPLY SECTION
For external devices access 12V, 5V, GND.
14. BUZZER SECTION
Buzzer already connected to port pin.
Flash the hex file then connect jumper you can check the output of buzzer.
15. LED SECTION
Connect jumper Port0.0 and Port0.7
Flash the hex file then you can see the led outputs.
[Link]/com Page 9
8051 DEVELOPMENT BOARD R1 2021
[Link]/com Page 10
