Last Update: 27/09/24

RB 65 On – Off version - wash gun for food industry - 24 bar – 2.4 MPa
Technical manual: E 124
Guns suitable for use up to 24 bar – 2.4 MPa rated pressure pumps.
No fluid passage upon trigger release.
DN15
• 30.6450.00 RB65 G1/2 F
• 30.6453.00 RB65 w/SWIVEL G1/2 F
• 30.6350.00 RB65 S.S.T. aisi316 w/SWIVEL G1/2 F

- Low pressure spray gun with possibility to fit lances

- Covered by semi-housings of non-stainable shockproof
plastic, entirely sealed and with 3 rubber protective rings.
- Plastic trigger protected by hand guard.
- Minimum fatigue for trigger opening and use.
- Internal structure in brass and Sst
- Ergonomic construction
- On request, inlet swivel connection.

TECHNICAL SPECIFICATIONS

P/N FRAME PISTON SEALS RATED (1) MAX WEIGHT INLET

MAX FLOW
COLOR MATERIAL MATERIAL PRESSURE TEMPERATURE
RATE
CONTINUOUS
USE
L/
USGpm bar MPa °C °F g lbs
min
30.6450.00 Blue Brass Viton 100 25.6 24 2.4 60 140 1042 2.3 G 1/2” F
Swivel
30.6453.00 Blue Brass Viton 100 25.6 24 2.4 60 140 1154 2.5
G 1/2” F
S.S.T. Swivel
30.6350.00 Blue Viton 100 25.6 24 2.4 60 140 1154 2.5
aisi316 G 1/2” F

(1) The gun has been designed for continuous use, at a water temperature of 60°C (140°F). It can resist at the max
temperature of 90°C (195°F) for short periods only, as, when the gun shuts off, the heater continues to transmit the heat
to the water, thus increasing both temperature and pressure up to high, dangerous values.
Using the gun at a water temperature higher than 60°C involves for the operator the use of adequate safety devices,
such as gloves, glasses, etc.

Instruction manual, maintenance, installation, spare parts.

For a correct utilization, follow the directions of this manual n. 12.9124.00
Re-print them on the Use and Maintenance booklet of the machine.

1
 Last Update: 27/09/24

DIMENSIONAL DRAWING AND PRESSURE DROP

INSTRUCTIONS
This product is to be utilized with clean fresh water, even slightly additivated with normal detergents. For use involving
different or corrosive liquids, contact the PA Technical department. Appropriate filtration should be installed when using
unclean liquids. Choose the gun in line with the data of nominal running (system rated pressure, max flow and max
temperature). In any case, the pressure of the machine should not exceed the permissible pressure rate imprinted on the
gun.

INSTALLATION
This gun was designed to operate with hot water (in compliance with the technical specs). Provide the plant generating
hot water with an equipment limiting the incidental increase of the fluid temperature.
Always fit a safety valve to protect the delivery conduct when the latter is under pressure.
Choose a suitable nozzle and ad just the valve mounted in the front of the gun, thus obtaining a constant supply and
avoiding unpleasant pressure spike when closing the system.
If the nozzle wears out, the pressure falls. When you install a new nozzle, adjust the system back to the original
pressure.

OPERATIONS
The gun opens and closes a high pressure conduct by means of a piston acting on a seat; the return is controlled by a
spring which releases the trigger.
WATER HOSE FEED
By high or very unsteady pressure values on delivery, it is necessary to mount a pressure reducer , both to level the flow
rate on delivery and to protect the system components.

2
 Last Update: 27/09/24

PROBLEMS AND SOLUTIONS

PROBLEMS PROBABLE CAUSES SOLUTIONS
Leakage from the nozzle Presence of impurities Clean
Gun seat worn out Replace seat
Fit adequate filters and/or check
Leaking seals Seals worn out Replace seal

Difficult trigger opening High pressure inside circuit Control the bypass valve and adjust if
necessary

Read this manual before starting the assembly.

For a correct utilization, follow the directions described in this manual and re-print them on the Use and maintenance
manual of the machine.

The present manual is valid for all the guns named RB65 ON-OFF.

SPARES
Use original PA spares only in order to get both a correct operation and a long lasting, reliable product.

MAINTENANCE
Maintenance has to be carried out by Specialized Technicians.

STANDARD: every 400 working hours (about 10,000 cycles), check and lubricate the seals with water
resistant grease.
SPECIAL: every 800 working hours (about 20,000 cycles), check the wear of the seals and internal parts and
if necessary, replace with original PA parts, taking care during installation to lubricate with water resistant
grease.

CAUTION: re-assemble the gun restoring the original conditions.

The manufacturer is not to be considered responsable for damage as a result from incorrect fitting
and maintenance.

Technical data, descriptions and illustrations are indicative and liable to modification without notice.

3
30.6450.00 RB65 [Link], on/off, brass 1/2FF -100l/min 30.6456.40 Lan,sst.RB65 1/2MF Bsp 400mm grip+cpl
30.6453.00 RB65 [Link], on/off, brass+sw5 1/2FF 100 30.6456.80 Lan,sst.RB65 1/2MF Bsp 800mm grip+cpl

Pos. P/N Description [Link] K1K2K3K4 Pos. P/N Description [Link] K1K2K3K4
1 30.6446.24 Casing-kit -RB65-100L v.2+scr. Sst. 1 1 22 30.6427.31R Coupl. -SW, 1/2F Bsp (1) 1 5
2 16.3075.51R S/tapping scr. 3,5x18 mm sst. 6 10 23 26.1075.85R Bushing, open 15,5x19x4mm (1) 1 10
3 30.6412.85R Front guard ring, TPEs blue v.2 1 5 24 10.3092.10R O-ring, 2x15 mm Vi 70 (1) 1 10
4 30.6413.85R Back guard ring, TPEs blue v.2 1 5 25 26.1074.85R Bushing, 15,5x19x4 mm PTFE (1) 1 10
5 30.6414.85R Lower guard ring, TPEs blue v.2 1 5 26 26.1072.31R Pin, M15x1-19 mm brass (1) 1 10
6 30.6407.31R Coupl., M16x1,5F-1/2F Bsp brass 1 5 27 30.6430.00 Swivel, brass-13mm [Link] ** 1 10
7 30.6409.36R Tube, M16x1,5 FF 130 mm brass 1 5 28 30.6431.31R 13mm hose barb, brass 1 3
8 30.6418.31R Regulating pin, M7 1 10 29 10.3060.00R O-ring, 1,78x12,42 mm 1 10
9 10.3064.10R O-ring 1.78 x 14 mm Viton 1 • • 10 30 10.3092.90R O-ring, 2x19 mm 1 10
10 30.6443.84R Sliding block, PA red 1 5 31 30.6432.31R Coupl. -SW, 1/2M Bsp brass 1 3
11 30.6417.31R Plug, M14x1 M brass 1 10 32 30.5017.35R Tube fastener, 1/2" Bsp (2) 1 5
12 10.3170.10R O-ring, 2,62x7,6 mm Vi 70 1 • • 10 33 30.6447.56R Tube, 1/2Bsp FF 796 mm Sst. (3) 1 1
13 30.6405.35R Housing -RB65, brass 1 3 33 30.6458.56R Tube, 1/2Bsp FF 398 mm Sst. (2) 1 1
14 30.6454.51R Spring, 2x12,9x40 mm Sst. 1 • 5 34 30.6457.31R Nozzle holder, 1/2Bsp FF (2) 1 5
15 30.6452.31R Piston -RB65 on/off, brass 1 • 5 35 13.5305.00R Plate, 8x1,5 mm Cu (2) 2 10
16 30.6408.85R Front seal, 11x20,5x3 mm FKM80 1 • • 10 36 11.4627.50R Hex. nut, M10, Sst. (2,3) 1 10
17 30.6451.31R Front coupl. -RB65 on/off, 1/2F Bsp brs 1 1 37 14.3799.51R Sst 10x21 mm washer (2,3) 1 5
18 30.6428.31R Parallel pin, 5x38 mm brass 1 10 38 41.0054.84R Knob, 32x115 mm PP blue (2,3) 1 5
19 30.6444.84R Trigger -RB65, PA red 1 5 39 16.2032.35R Sst. screw, DIN933 M10x35 mm (2,3) 1 5
20 30.6415.51R Trigger retainer, Sst. 1 5 40 30.6478.84R Plug, Knob PP blue (2,3) 1 5
21 30.6426.31R Coupl. -SW, M15x1F-M16x1,5F (1) 1 3 41 15.3814.00 Label "2,4MPa Tubo inox - PA" 1 1

** On request

Kit P/N Description

K1 30.6422.24 Seals spares kit -RB65, 3x1pcs. 1
K2 30.6459.24 Repair kit -RB65 on/off, 5x1pcs. 1

(1) 30.6453.00 (2) 30.6456.40 (3) 30.6456.80

Last updated 25/06/2025