HINDUSTAN AERONAUTICS LIMITED

BANGALORE
FACILITIES MANAGEMENT DIVISION

NAME OF THE WORK: Construction of Shed to Raw Material for Outsourcing Department at LCA Plant – II at HAL [BC] – [Including Electrical Work].
CONTRACT NO. HAL/FMD/C-48/25-26

PRICE BID

Name of the Contractor : x

Sl. Rate in Figs

Specification Quantity Unit Rate in Words Amount
No. [Excluding GST]
Preamble:
(1) The subject work has been called on works contract basis and prevailing GST for same is 18%. Any change in GST +/- during the currency of contract shall be on HAL
account. The Tenderer shall abide by prevailing GST act.
(2) L1 (lowest quote) will be determined based on the total quoted amount including GST.
(3) This BOQ specification has to be read in conjunction with relevant CPWD specifications amended upto date/ detailed technical specification in tender document and tender
drawings if any.

Part 'I' - Civil Works431

1 Earth work in excavation by mechanical means (Hydraulic excavator)
/ manual means over areas in all kinds of soft / hard soil for
foundations, footings, column pedestals or members as per the
drawing, etc., (exceeding 30cm in depth, 1.50m in width as well as 10Sq m
on plan) including removal of vegetation and in-equalities, shoring, strutting
for protecting the sides of foundation if required, removing slips or falls in Rupees One Hundred
431.00 Cu m 173.00 74563.00
excavation, forming steps in sides of deep excavations and their removal or Seventy Three Only
covering up, levelling, ramming the bottom of excavation, getting out and
disposal of excavated earth lead upto 50m for all lifts with all labour, tools
& tackles, plant & machinery, hire & fuel charges, etc., all complete as directed
by Engineer-in-Charge.

2 Returning / filling in with useful excavated soil (excluding rock), free from
salts, organic or other deleterious matter (Other than black cotton soil & rock,
etc., in trenches, plinth, sides of foundations, etc., spreading in layers not
exceeding 20cm thick, watering, breaking / removing clods exceeding 50mm, Rupees One Hundred Ninety
ramming and consolidation of each deposited layer, etc., with all labour, tools 393.00 Cu m 191.02 75070.86
One and Two Paise Only
& tackles, plant & machinery, etc., lead upto 50m and for all lifts, etc., all
complete as directed by the Engineer-in-Charge.

Page 1
 NAME OF THE WORK: Construction of Shed to Raw Material for Outsourcing Department at LCA Plant – II at HAL [BC] – [Including Electrical Work].
CONTRACT NO. HAL/FMD/C-48/25-26

PRICE BID

Name of the Contractor : x

Sl. Rate in Figs

Specification Quantity Unit Rate in Words Amount
No. [Excluding GST]
3 Earth work in excavation by mechanical means (Hydraulic excavator) /
manual means in foundation trenches or drains, pipes, cables, ramp sides, etc.
in all kinds of soils (not exceeding 1.50m in width or 10Sq m on plan),
including dressing of sides and ramming of bottoms, for all lifts, including Rupees Two Hundred Fifty
getting out the excavated soil and disposal of surplus excavated soil as 4.00 Cu m 253.69 Three and Sixty Nine Paise 1014.76
directed, within a lead of 50m with all labour, tools & tackles, plant & Only
machinery, hire & fuel charges, etc., all complete as directed by Engineer-in-
Charge.

4 Extra for levelling & neatly dressing the excess soil in the visinity, etc., all
complete as directed by Engineer-in-Charge. Rupees Ninety and Sixty
42.00 Cu m 90.69 3808.98
Nine Paise Only

5 Supplying, mixing and placing plain cement concrete ([Link]) of required

thickness using 20mm nominal size down graded hard stone / granite
aggregate in accordance with IS 456 in Cills, fillets, coping, etc., upto floor
five level, including formwork, mechanical mixing, transporting, vibrating, Rupees Nine Thousand Six
consolidation, levelling, curing, dewatering if any, all materials, labour, lead & 0.50 Cu m 9643.63 Hundred Forty Three and 4821.82
lift, tools, plant & machinery, keeping concrete well wetted during the curing Sixty Three Paise Only
period and protecting it in extreme weather conditions, etc., including
finishing, etc., all complete as directed by the Engineer-in-Charge.

6 Making plinth protection 50mm thick of cement concrete [Link] (1 cement :

3 coarse sand (zone-III) derived from natural sources : 6 graded stone
aggregate 20mm nominal size derived from natural sources) over 75mm thick Rupees Seven Hundred
bed of dry brick ballast 40mm nominal size, well rammed and consolidated and 80.00 Sq m 730.25 Thirty and Twenty Five Paise 58420.00
grouted with fine sand, including necessary curing, excavation, levelling & Only
dressing & finishing the top smooth, etc., all complete as directed by the
Engineer-in-Charge.

7 Providing, mixing and laying in position cement concrete ([Link]) derived

from natural sources of required thickness using 20mm down graded hard
stone/granite aggregate in accordance with IS 456 in all works up to plinth
level and in Flooring including mechanical mixing, transporting, vibrating, Rupees Seven Thousand One
consolidation, levelling, curing, dewatering if any, all materials, labour, lead & 39.00 Cu m 7109.25 Hundred Nine and Twenty 277260.75
lift, tools, plant & machinery, keeping concrete well wetted during the curing Five Paise Only
period and protecting it in extreme weather conditions, etc, all complete as
directed by the Engineer-in-Charge.

Page 2
 NAME OF THE WORK: Construction of Shed to Raw Material for Outsourcing Department at LCA Plant – II at HAL [BC] – [Including Electrical Work].
CONTRACT NO. HAL/FMD/C-48/25-26

PRICE BID

Name of the Contractor : x

Sl. Rate in Figs

Specification Quantity Unit Rate in Words Amount
No. [Excluding GST]
8 Formwork (Centering and shuttering including strutting, propping etc, and
removal of form) for the following RCC members which are defined as below,
in fair finished by providing timber, wooden planks, runners / M.S. sheets with
all supports, struts, braces, wedges, scaffolds, bracings, ladders, gangways,
dressing with oil including M.S. bolts nuts and washers, temporary openings,
filleting for a stop, chamfered edges, internal / external splayed, rounded
angles or grooves for forming throating including making temporary openings
in the forms for pouring concrete, etc., all complete as directed by the
Engineer-in-Charge for the sub-items mentioned below.
Note: Formwork material is contractor's own property and shall be removed
after completion of work.

a) Foundations, footings, bases of columns, pedestal, steps, etc., for

mass concrete. Rupees Three Hundred
156.00 Sq m 382.19 Eighty Two and Nineteen 59621.64
Paise Only

b) Lintels, Beams, etc.,

Rupees Seven Hundred
181.00 Sq m 717.68 Seventeen and Sixty Eight 129900.08
Paise Only

c) For Columns, Pillars, Piers, etc.,

Rupees Nine Hundred Thirty
48.00 Sq m 936.87 Six and Eighty Seven Paise 44969.76
Only

d) Chajja, Weather shade,Canopies, Corbels, etc., including edges

Rupees Nine Hundred
41.00 Sq m 926.93 Twenty Six and Ninety Three 38004.13
Paise Only

Page 3
 NAME OF THE WORK: Construction of Shed to Raw Material for Outsourcing Department at LCA Plant – II at HAL [BC] – [Including Electrical Work].
CONTRACT NO. HAL/FMD/C-48/25-26

PRICE BID

Name of the Contractor : x

Sl. Rate in Figs

Specification Quantity Unit Rate in Words Amount
No. [Excluding GST]
9 Supplying, straightening, fabricating (cutting & bending), placing in position
and binding steel reinforcement of TMT bars of not less than Fe 500 D
conforming to IS 1786 for all concrete reinforcment members / works above /
below plinth level, including cutting to length, bending to shape required,
including cranking, bending spirally for hooping for column, hooking ends and
binding with mild steel wire (Annealed) not less than 0.90mm dia or securing Rupees One Lakh Five
with clips, including fixing and bracing, wastage, welding, supporting or 10.856 MT 105120.00 Thousand One Hundred 1141182.72
otherwise holding firmly in position so that the placing and ramming of Twenty Only
concrete will not displace it, etc., complete all as per specifications, drawings
and as directed by the Engineer-in-Charge.
Note: a) Only authorized laps, chairs etc. shall be considered for
measurement.
b) The exposed Reinforcement bars shall be coated with cement slurry.
10 Providing and laying in position ready mixed or site batched M25 Grade with
minimum cement content of 330 kg/m3 design mix cement concrete for
reinforced cement concrete work; using coarseaggregate and fine
aggregate derived from natural sources, PortlandPozzolana / Ordinary Portland
/ Portland Slag cement, admixtures in recommended proportions as per IS:
9103 to accelerate / retard setting of concrete, to improve durability and
workability without impairing strength; including pumping of concrete to site of
laying, consolidation, levelling, curing, scaffolding, all materials, labour,
carriage for all leads & lifts; but excluding the cost of centering, shuttering,
finishing and reinforcement as per direction of the Engineer-in-Charge.
Note: (i) Mix design to be obtained from Govt. / NABL laboratory for site
batching concrete.

a) All works upto plinth level including necessary openings and packing if any
for laying pipes, cables, etc., Rupees Nine Thousand Two
47.00 Cu m 9263.12 Hundred Sixty Three and 435366.64
Twelve Paise Only

b) All works above plinth level upto floor V level including necessary openings
and packing if any for laying pipes, cables etc., Rupees Nine Thousand Six
17.00 Cu m 9609.72 Hundred Nine and Seventy 163365.24
Two Paise Only

Page 4
 NAME OF THE WORK: Construction of Shed to Raw Material for Outsourcing Department at LCA Plant – II at HAL [BC] – [Including Electrical Work].
CONTRACT NO. HAL/FMD/C-48/25-26

PRICE BID

Name of the Contractor : x

Sl. Rate in Figs

Specification Quantity Unit Rate in Words Amount
No. [Excluding GST]
11 Construction of Coursed rubble masonry (first sort) in cement mortar
(1:6) (1 cement : 6 coarse sand) with hard stone, solidly hearted faces, beds
and joints squared back, in foundation and below plinth including levelling up
Rupees Eight Thousand Five
with cement concrete [Link] (1 cement : 6 coarse sand : 12 graded stone 1.50 Cu m 8588.02 Hundred Eighty Eight and 12882.03
aggregate 20mm nominal size) upto plinth level, raking out joints 10mm deep,
Two Paise Only
curing, providing weep holes if any, etc., all complete as directed by the
Engineer-in-Charge.

12 Providing and fixing expansion hold fasteners with threaded dia of 6mm
on C.C. / R.C.C. / Brick masonry surface backing including drilling necessary
Rupees Thirty Five and
holes and the cost of bolt, etc., all complete as per the architectural drawings 140.00 Each 35.83 5016.20
Eighty Three Paise Only
and the directions of Engineer-in-Charge .

13 Providing and fixing M.S. grills of required pattern in openings/ wooden

frames of windows, Ventilators, etc., with rawl plugs screws, ends of bars
shouldered and / or riveted, welded, etc., of approved design using MS
structurals such as flats, angles, round / square bars, etc., including necessary Rupees Two Hundred Thirty
432.00 Kgs 232.30 100353.60
cutting, welding, embedding in concrete, masonry etc.,including priming coat Two and Thirty Paise Only
with approved steel primer, etc., all complete as directed by the Engineer-in-
Charge.

14 Supplying and fixing the [40 x 5]mm flat iron hold fast 40cm long of
approved make and design to door with all required screws, bolts, nuts,
washers, etc., including fixing to frame with 10mm diameter bolts, nuts and
wooden plugs and embedding in cement concrete block [30 x 10 x 15]cm Rupees Two Hundred Twenty
6.00 Each 223.04 1338.24
[Link] mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm Three and Four Paise Only
nominal size), etc., all complete as directed by the Engineer-in-Charge.

15 Structural steel work riveted, bolted or welded in built up sections, trusses

and framed work, including cutting, hoisting, fixing in position and applying a Rupees One Lakh Thirty
priming coat of approved steel primer, etc., all complete as per direction of 18.534 MT 130310.00 Thousand Three Hundred Ten 2415165.54
Engineer- in-Charge. Only

Page 5
 NAME OF THE WORK: Construction of Shed to Raw Material for Outsourcing Department at LCA Plant – II at HAL [BC] – [Including Electrical Work].
CONTRACT NO. HAL/FMD/C-48/25-26

PRICE BID

Name of the Contractor : x

Sl. Rate in Figs

Specification Quantity Unit Rate in Words Amount
No. [Excluding GST]
16 Supplying, fabricating and fixing second class teak wooden plain,
solid, straight chowkats and frames of doors, windows, partitions, wall
panelling frames and other frames, wrought framed, rebated on the solid, Rupees One Lakh Thirty Nine
rounded or chamfered, put together with glue, pinned at joints and fixed to Thousand Three Hundred
0.09 Cu m 139315.39 12538.39
wall or in position with hold fast lugs or with dash fasteners of required dia & Fifteen and Thirty Nine Paise
length, etc., all complete as directed by the Engineer-in-Charge. Only

17 Providing, fabricating and fixing 35mm thick flush door shutters

conforming to IS :2202 (Part I) decorative type, core of block board
construction with frame of 1st class hard wood & lipping with 2nd class teak
wood battens 25mm minimum depth on all edges and well matched Rupees Three Thousand
commercial 3ply veneering with vertical grains or cross bands including ISI 2.88 Sq m 3836.13 Eight Hundred Thirty Six and 11048.05
marked butt hinges with necessary screws and face veneers on both faces of Thirteen Paise Only
shutters and provision of rebates,suitable blocks for taking mortice locks,
latches or other fittings, fitting to frames / chowkats, etc., all complete as
directed by the Engineer-in-Charge.
18 Providing, fixing, testing and commissioning single socketed pipes of
110mm dia, on wall face unplasticised Rigid PVC rain water pipes of
6Kg/cm² SWR grade and of approved make conforming to IS : 13592 Type A,
including jointing together with seal ring conforming to IS : 5382, leaving 10 Rupees Three Hundred Sixty
mm gap for thermal expansion and all necessary fittings & specials, bends, 36.00 Rm 367.81 Seven and Eighty One Paise 13241.16
branches, sockets, clamps, pipe cutting and wastages, cutting and making Only
good the walls, connecting to existing lines, etc., along with removal of
existing rain water pipes, etc., all complete as directed by the Engineer-in-
Charge.

Page 6
 NAME OF THE WORK: Construction of Shed to Raw Material for Outsourcing Department at LCA Plant – II at HAL [BC] – [Including Electrical Work].
CONTRACT NO. HAL/FMD/C-48/25-26

PRICE BID

Name of the Contractor : x

Sl. Rate in Figs

Specification Quantity Unit Rate in Words Amount
No. [Excluding GST]
19 Providing and fixing Pre-painted Galvalume sheet (PPGL) / precoated
galvanised iron profile sheets (size, shape and pitch of corrugation as approved
by Engineer-in-Charge) of total coated thickness 0.50mm (base metal of
minimum 0.45mm thickness with total coating thickness of 0.05mm) with zinc-
AL alloy coating over 240 mpa steel grade, 5-7 microns epoxy primer on both
side of the sheet and Silicon Modified polyester (SMP) top coat 15-18
microns. Sheet should have protective guard film of 25 microns minimum to
avoid scratches during transportation and should be supplied in single length
upto 12 metre or as desired by Engineer-in-Charge. The sheet shall be fixed
Rupees Seven Hundred
using self drilling /self tapping screws of size [5.50 x 55]mm with EPDM seal,
531.00 Sq m 719.88 Nineteen and Eighty Eight 382256.28
complete upto any pitch in horizontal / vertical or curved surfaces, excluding
Paise Only
the cost of purlins, rafters and trusses and including cutting to size and shape
wherever required, etc., all complete as directed by the Engineer-in-Charge.
Note: A performance guarantee bond for 5 years for leak proof roofing shall be
given by the contractor on non-judicial stamp paper of Rs.500/-. The 10% of
completed value of this item shall be dedcuted as defect liability deposit and
the same shall be returned after sucessful completion of 5 years from the date
of completion of contract / project as a whole.

20 Providing and fixing Ridge (width 500-600mm) Pre-painted Galvalume

sheet (PPGL) / precoated galvanised steel sheet roofing accessories of total
coated thickness 0.50 mm (base metal of minimum 0.45mm thickness with
total coating thickness of 0.05mm) with with zinc-AL alloy coating over 240
mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and
Silicon Modified polyester (SMP) top coat 15-18 microns polyester top
coat 15-18 microns using self drilling/ self tapping screws complete Ridge Rupees Five Hundred
Plain [500-600mm], etc., all complete as directed by the Engineer-in-Charge. 20.00 Rm 518.83 Eighteen and Eighty Three 10376.60
Note: A performance guarantee bond for 5 years for leak proof roofing shall be Paise Only
given by the contractor on non-judicial stamp paper of Rs.500/-. The 10% of
completed value of this item shall be dedcuted as defect liability deposit and
the same shall be returned after sucessful completion of 5 years from the date
of completion of contract / project as a whole.

Page 7
 NAME OF THE WORK: Construction of Shed to Raw Material for Outsourcing Department at LCA Plant – II at HAL [BC] – [Including Electrical Work].
CONTRACT NO. HAL/FMD/C-48/25-26

PRICE BID

Name of the Contractor : x

Sl. Rate in Figs

Specification Quantity Unit Rate in Words Amount
No. [Excluding GST]
21 Providing and fixing Falshings up to width of 600mm Pre-painted
Galvalume sheet (PPGL)/ precoated galvanised steel sheet roofing
accessories of total coated thickness 0.50 mm (base metal of minimum 0.45
mm thickness with total coating thickness of 0.05 mm) with [Link]
coating, in 240 mpa steel grade, 5-7 microns epoxy primer on both side
and Silicon Modified polyester (SMP) of the sheet and polyester top coat Rupees Four Hundred
15-18 microns using self drilling/ self tapping screws complete, etc., all 92.00 Rm 473.26 Seventy Three and Twenty 43539.92
complete as directed by the Engineer-in-Charge. Six Paise Only
Note: A performance guarantee bond for 5 years for leak proof roofing shall be
given by the contractor on non-judicial stamp paper of Rs.500/-. The 10% of
completed value of this item shall be dedcuted as defect liability deposit and
the same shall be returned after sucessful completion of 5 years from the date
of completion of contract / project as a whole.

22 Providing and fixing Gutter to Girth 600mm Pre-painted Galvalume sheet

(PPGL) / precoated galvanised steel sheet roofing accessories of total coated
thickness 0.50mm (base metal of minimum 0.45mm thickness with total
coating thickness of 0.05 mm) with [Link] over 240 mpa steel grade,
5-7 microns epoxy primer and Silicon Modified polyester (SMP) top coat
15-18 microns on both side of the sheet using self drilling/ self tapping screws, Rupees One Thousand Two
etc., all complete as directed by the Engineer-in-Charge. 40.00 Rm 1280.31 Hundred Eighty and Thirty 51212.40
Note: A performance guarantee bond for 5 years for leak proof roofing shall be One Paise Only
given by the contractor on non-judicial stamp paper of Rs.500/-. The 10% of
completed value of this item shall be dedcuted as defect liability deposit and
the same shall be returned after sucessful completion of 5 years from the date
of completion of contract / project as a whole.

23 Providing, applying and laying cement mortar (1:6) plastering 15mm

thick on brick / solid blocks / concrete surfaces, finished even and smooth
with trowel for Internal / External walls, etc., including supply and fixing
of hexagonal chicken mesh minimum 150mm wide having opening [20 x
20]mm of 26 gauge at juncitons of concrete & brick work or between different
Rupees Three Hundred
material, including making grooves as per the requirement not exceeding
189.00 Sq m 373.27 Seventy Three and Twenty 70548.03
10mm width and not exceeding 10mm deep with necesary materials, labour,
Seven Paise Only
scaffolding, curing, tools and tackles, etc., at all heights, etc., all complete as
directed by the Engineer-in-Charge.

Page 8
 NAME OF THE WORK: Construction of Shed to Raw Material for Outsourcing Department at LCA Plant – II at HAL [BC] – [Including Electrical Work].
CONTRACT NO. HAL/FMD/C-48/25-26

PRICE BID

Name of the Contractor : x

Sl. Rate in Figs

Specification Quantity Unit Rate in Words Amount
No. [Excluding GST]
24 Providing, applying and laying 18mm thick cement plaster work in two
coats for external areas as directed. First coat 12mm thick in cement
mortar (1:5) made rough to recieve top coat, second coat 6mm thick in
cement mortar (1:6) , final surface finished with a floating coat of neat cement
after necessary preparation of surface, at all levels including supply and fixing Rupees Five Hundred Five
of hexagonal chicken mesh minimum 150mm wide having opening [20 x 308.00 Sq m 505.36 155650.88
and Thirty Six Paise Only
20]mm of 26 gauge at juncitons of concrete & brick work or between different
material, with necesary materials, labour, scaffoldings, curing, tools and
tackles, plants, etc., threading if any as directed, etc., all complete as directed
by the Engineer-in-Charge.
25 Painting newly plastered external surfaces with two or more coats
applied at 1.43 litre/10Sq m/ as per manufacturer specifications of 100%
premium acrylic emulsion paint having VOC less than 50 grams/ litre and UV
resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance
exterior paint with silicon additives of approved make, colour, shade, tint &
pattern at all levels, over and including a coat of approved acrylic primer Rupees One Hundred
including preparing the surface by removing loose dirt and any organic growth, 308.00 Sq m 176.65 Seventy Six and Sixty Five 54408.20
filling of cracks, necessary scaffolding, etc., all complete as directed by the Paise Only
Engineer-in-Charge.
Note: The paint shall have anti-algal, anti-fungal, UV resistant & anti-
tarnishing qualities with 100% acrylic base and silicon or elastomeric additives.

26 Painting Steel surfaces of any description with two coats of synthetic

enamel paint of approved colour,brand and manufacture to give an even
shade, including preparation of surface by rubbing with fine grade of abrasive Rupees Two Hundred Twenty
1099.00 Sq m 220.50 242329.50
paper to ensure smooth, etc., all complete as directed by the Engineer-in- and Fifty Paise Only
Charge.

Page 9
 NAME OF THE WORK: Construction of Shed to Raw Material for Outsourcing Department at LCA Plant – II at HAL [BC] – [Including Electrical Work].
CONTRACT NO. HAL/FMD/C-48/25-26

PRICE BID

Name of the Contractor : x

Sl. Rate in Figs

Specification Quantity Unit Rate in Words Amount
No. [Excluding GST]
27 Painting newly plastered interior surfaces with two coats of premium
acrylic emulsion paint of interior grade having VOC (Volatile Organic
Compound) content less than 50 grams/ litre conforming to IS 15489, of
approved make, brand, colour, shade, tint, manufacture & pattern at all levels,
including preparing the surface by removing loose dirt and any organic growth,
smoothening the surface by using suitable emery paper, filling crevices and
Rupees Three Hundred Sixty
finishing even and smooth by providing and applying white cement based putty
189.00 Sq m 363.33 Three and Thirty Three Paise 68669.37
of average thickness of 1mm in 2 coats of approved brand and manufacture
Only
over the plastered wall surface and followed by the applying priming coat with
primer of approved brand and manufacture, having low VOC (Volatile Organic
Compound ) content With water thinnable cement primer on applied putty
having VOC content less than 50 grams/litre, necessary scaffolding, etc., all
complete as directed by the Engineer-in-Charge.

28 French Polishing on wood work on New work with two or more coats
Rupees Four Hundred Thirty
including a coat of wood filler, etc., all complete as directed by the Engineer-in-
6.05 Sq m 434.91 Four and Ninety One Paise 2631.21
Charge.
Only

29 Supply, laying and compacting of granular sub-base in flooring,

subbases, ramps, etc., upto plinth level of requisite grading by providing close
graded Material conforming to specifications, mixing in a mechanical mix plant
at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, Rupees Two Thousand Seven
spreading in uniform layers of specified thickness with motor grader on 43.00 Cu m 2737.15 Hundred Thirty Seven and 117697.45
prepared surface and compacting with vibratory power roller to achieve the Fifteen Paise Only
desired density, etc., all complete as per specifications and directions of
Engineer-in-Charge.

Page 10
 NAME OF THE WORK: Construction of Shed to Raw Material for Outsourcing Department at LCA Plant – II at HAL [BC] – [Including Electrical Work].
CONTRACT NO. HAL/FMD/C-48/25-26

PRICE BID

Name of the Contractor : x

Sl. Rate in Figs

Specification Quantity Unit Rate in Words Amount
No. [Excluding GST]
30 Providing and laying design mix cement concrete of M-30 grade
manufactured in automatic batching plant (RMC plant) including transportation
to site in transit mixer in roads / hardstandings / flooring using cement
content as per design mix, using coarse sand and graded stone aggregate of
approve size in appropriate proportions as per approved & specified design
criteria, laying over reinforcement, spreading and compacting mechanically by
Rupees Ten Thousand Eight
using needle vibrator, levelling to the required slope / camber, finishing with
50.00 Cu m 10816.29 Hundred Sixteen and Twenty 540814.50
required texture including steel form work with sturdy M.S channel sections,
Nine Paise Only
curing making provision for contraction/expansion joints, construction and
longitudinal joints (10mm wide X 50mm deep) by groove cutting machine,
providing and filling joints with approved joint filler and sealent, etc., all
complete as per the drawings/directions of Engineer-in-Charge.
Note: Cement content considered in M-30 is @ 340 kg/Cu m.

31 Providing and fixing pre-moulded joint filler in expansion joints of RCC roads /
CC pavements after making the joints dust free with high pressure air jet
per 5cm
cleaners, etc., all complete as per direction of the Engineer-in-Charge. (Pre-
depth and
moulded joint fillers shall be made of bitumen hot sealing compound Rupees Twenty Five and
48.00 1cm width 25.83 1239.84
impregnated fibre board having impregnation more than 35%, conforming to Eighty Three Paise Only
and 1m
IS:1838 for fibre board and IS: 1834 for hot sealing bitumen compound grade
length
A.)

32 Providing and filling in position rubberized bitumen hot sealing compound for per 5cm
sealing of expansion joints in roads / pavements, etc., all complete as per depth and Rupees Forty Two and
48.00 42.15 2023.20
direction of the Engineer-in-Charge. 1cm width Fifteen Paise Only
and 1m
length

Page 11
 NAME OF THE WORK: Construction of Shed to Raw Material for Outsourcing Department at LCA Plant – II at HAL [BC] – [Including Electrical Work].
CONTRACT NO. HAL/FMD/C-48/25-26

PRICE BID

Name of the Contractor : x

Sl. Rate in Figs

Specification Quantity Unit Rate in Words Amount
No. [Excluding GST]
33 Providing, fabricating and fixing aluminium work for partitions, Curtain
wall frames, Windows Fixed Portion i.e frames (Min. thickness of powder
coating 50 microns) made up of aluminium extruded sections, windows, etc.,of
approved make,
a) Sliding Window Frame: Top and side sections of the frames to
accomodate the shutter section.
b) Bottom section of the frame shall be with gutter and partitions with
extruded built up standard tubular sections / appropriate Z sections and other
sections of approved make conforming to IS: 733 and IS: 1285, Rupees Five Hundred
c) Shutters are to be provided with galss of approved size for two shutters and 230.00 Kgs 517.41 Seventeen and Forty One 119004.30
stainless steel fly proof mesh for one shutter fixed with good quality tapered Paise Only
aluminium interlocking screwless snap on type glazing clip not less than
0.90mm thick.
Aluminium sections shall be smooth, rust free, straight, mitred and jointed
mechanically wherever required including cleat angle, Aluminium snap beading
for glazing / paneling, C.P. brass / stainless steel screws, all complete as per
architectural drawings and the directions of Engineer-in-Charge. (Glazing,
Panelling, fly proof mesh will be paid seperately).
34 Providing, fabricating and fixing aluminium work for shutters of doors,
windows and ventilators including rollers, etc., all complete as directed Rupees Six Hundred
by the Engineer-in-Charge. 82.50 Kgs 618.33 Eighteen and Thirty Three 51012.23
Paise Only

35 Providing and fixing glazing in aluminium door, window, ventilator

shutters and partitions, etc., With float glass panes of 5mm thickness Rupees One Thousand Four
(weight not less than 12.50 kg/sqm) along with EPDM rubber / neoprene 110.00 Sq m 1466.99 Hundred Sixty Six and Ninety 161368.90
gasket, etc., all complete as per the architectural drawings and the directions Nine Paise Only
of Engineer-in-Charge.

36 Providing and laying factory made Precast concrete solid blocks of

200mm thickness of grade M10 made of Normal resources / C & D waste from
approved manufacturer in superstructure above plinth level upto floor V level Rupees Nine Thousand Five
with Cement mortar (1:6) in true line and height including curing, cleaning, 24.00 Cu m 9594.37 Hundred Ninety Four and 230264.88
etc., all complete as per the direction of Engineer-in-Charge. Thirty Seven Paise Only

Page 12
 NAME OF THE WORK: Construction of Shed to Raw Material for Outsourcing Department at LCA Plant – II at HAL [BC] – [Including Electrical Work].
CONTRACT NO. HAL/FMD/C-48/25-26

PRICE BID

Name of the Contractor : x

Sl. Rate in Figs

Specification Quantity Unit Rate in Words Amount
No. [Excluding GST]
37 Supplying and fixing Motorized G.I. rolling shutter, made of approximate
size [5 X 5]m and approved make. The curtain shall be constructed from Tata
Bluescope/JSW 150 gsm single skinned galvalume steel laths with natural
finish of min. 1.25mm thickness and interlocking distance of min 75mm. Side
guides shall be made of min. 2 or 3.15mm thick heavy duty TG Galvanised
steel, as per the site requirement, along with necessary fixtures like
cleats(spacing shall not exceed 0.75m) or supports brackets for attachments
to the walls or column by screws or bolts and necessary [Link] size of the
guide channels shall be conforming to Is:6248-1979. Single piece G.I. Heavy
duty mild steel suspension shaft along with roller of sufficient diameter with
springs shall be provided along with necessary hexagonal bracket plate of
Rupees Nine Thousand Four
minimum 3.15mm thickness, size conforming to Is:6248-1979 and square bar,
18.00 Sq m 9407.35 Hundred Seven and Thirty 169332.30
if necessary. The provision of Pressed galvalume steel hood cover with
Five Paise Only
reinforced bracket as required to suit the shutter width and motor cover with
natural finish of min. 0.90mm thick and of reuired shape along with necessary
fixtures and stiffeners like angle cleats, angle or flat stiffeners, etc., shall be
provided. Bottom profile shall be of G.I. plate with angle stiffner. The bottom
rail shall be fixed with extruded rubber bottom seal that shall seal against the
floor when the door is fully closed. The CE Certified CRS Compact Gear
motorised system shall be indirect drive type along with system power supply
wired with industrial plug and three station push button / switch with deadman
control and arrangements for inside and outside locking. A provision of suitable
safety devices/system like inbuilt limit switches,

External safety brake's, Control switch, etc., are to be provided in accordance

with EN 14121-1:2007 Safety of machinery. Provision shall be made for
manual operation by hand chain in emergency condition, etc., all complete &
fully operational. The rate is inclusive of two coats of painting, of approved
shade and manufacture, over a coat of grey epoxy primer by spray including
preparation of surface, all materials, labour, machinery, tools and tackels, etc.,
all complete as directed by the Engineer-in-Charge.
Note: (i) Clear opening shall be measured for payment.
(ii) The quoted rate shall be for the entire work and making it operational.

Rupees Seventy Five Lakh Fifty Three Thousand Three Hundred Thirty
Sub-Total of Part 'I' - Civil Works (Excluding GST) 7553333.57
Three and Fifty Six Paise Only

Page 13
 NAME OF THE WORK: Construction of Shed to Raw Material for Outsourcing Department at LCA Plant – II at HAL [BC] – [Including Electrical Work].
CONTRACT NO. HAL/FMD/C-48/25-26

PRICE BID

Name of the Contractor : x

Sl. Rate in Figs

Specification Quantity Unit Rate in Words Amount
No. [Excluding GST]

Part 'II' - Electrical Works

1 Supply, fixing to existing MS perlins at approx. 6.5 to 7 mtr height(Approx.),
using suitable MS angle frame work with required fixing hardwares etc., as per
site requirement, testing & commissioning of industrial type highbay LED
lighting fixture of wattage not exceeding 120 watts made out of high pressure
diecast aluminium housing, diffuser made of high grade toughened glass(or as
per OEM standards), integral control gear, eye hook etc., . The technical
parameters of lighting fixtures are as below: The luminaire should have Lumen
efficacy ≥ 140lm/watt and lumen output not less than 16800lumens, PF>0.90
Rupees Eighteen Thousand
and Colour temperature shall be ≥5700K, CRI≥70, THD <10%, IP66/65
9.00 Nos 18827.97 Eight Hundred Twenty Seven 169451.73
operating on single phase 230V voltage 50 Hz AC supply with voltage range
and Ninety Seven Paise Only
140-270V with standard accessories complete in all respects and as directed
by Engineer in-charge. The fitting may be of Crompton model no:CIP-320-120-
57-60D-HL4-GL-NSR/ Equivalent model in other approved makes. LED used in
the lighting fixtures should be one of the approved make. LM79 certification for
luminaries & LM80 certificate for LED shall be produced.
Note: MS supports will be paid separately.

2 Distribution Boards

Supply, fixing, testing & commissioning of the following factory built powder
coated Double door MCB/MCCB DB of any approved make fabricated out of
M.S. sheet steel enclosure & necessary cutouts for operating the MCB knobs &
comprising of 200 amps tinned copper busbars & earthing bus with tapped
holes including internal wiring with stranded copper PVC wires or suitable size
copper strips etc. & fixing the DB in flush with wall/ on wall as per site
requirement with necessary M.S. angle supports(including), chipping the wall
and replastering to smooth finish etc., wherever required as per site condition,
complete in all respects, as directed by Engineer-in-charge and comprising the
following as detailed below:

a) 4 way HTPN MCB DB

Rupees Four Thousand Two
1.00 No 4232.51 Hundred Thirty Two and Fifty 4232.51
One Paise Only

Page 14
 NAME OF THE WORK: Construction of Shed to Raw Material for Outsourcing Department at LCA Plant – II at HAL [BC] – [Including Electrical Work].
CONTRACT NO. HAL/FMD/C-48/25-26

PRICE BID

Name of the Contractor : x

Sl. Rate in Figs

Specification Quantity Unit Rate in Words Amount
No. [Excluding GST]
3 MCCBs, MCBs & RCBO

Supply, fixing, testing & commissioning of following rating

MCCB/MCB/RCBO in the existing Distribution board/powder coated
enclosure as directed by Engineer-in-Charge.

a) 40-63 amps. ratings , 4P MCB, "C" curve, 10 KA breaking capacity.

Rupees One Thousand Six
1.00 No 1638.98 Hundred Thirty Eight and 1638.98
Ninety Eight Paise Only
b) 6-32 amps. ratings , SP MCB, "C" curve, 10 KA breaking capacity.
Rupees Two Hundred Sixty
12.00 Nos 264.85 Four and Eighty Five Paise 3178.20
Only
4 Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket
outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 Rupees One Thousand Six
amps “C” curve, SP, MCB, in sheet steel enclosure, on surface or in 2.00 Nos 1677.08 Hundred Seventy Seven and 3354.16
recess, with chained metal cover for the socket out let and complete Eight Paise Only
with connections, testing and commissioning etc. as required.

5 Supply & laying, testing & commissioning in the already excavated cable
trench/fixing on wall/duct wall/cable tray with necessary M.S clamps / Rupees Two Hundred Twelve
encasing in pipes etc., testing & commissioning of 3.5Cx25 Sqmm XLPE 70.00 Mtrs 212.02 14841.40
and Two Paise Only
insulated Aluminium conductor 1100V gr. Armoured U.G cables complete in all
respect as directed by EIC.
6 Supplying and making end termination with brass compression gland
and aluminium lugs for following size of PVC insulated and PVC
sheathed / XLPE armoured aluminium conductor cable of 1.1 KV
grade as required

3.5C X 25 sq. mm Al arm cable

Rupees Three Hundred
2.00 Nos 323.82 Twenty Three and Eighty Two 647.64
Paise Only

7 Supplying and fixing following suitable size GI Box with modular plate
and cover on front on surface or in recess, including providing and
Rupees Six Hundred Six and
fixing 6 pin 5/6A & 15/16A modular socket outlet and 15/16 A 5.00 Nos 606.26 3031.30
Twenty Six Paise Only
modular switch, connections etc., as required.

Page 15
 NAME OF THE WORK: Construction of Shed to Raw Material for Outsourcing Department at LCA Plant – II at HAL [BC] – [Including Electrical Work].
CONTRACT NO. HAL/FMD/C-48/25-26

PRICE BID

Name of the Contractor : x

Sl. Rate in Figs

Specification Quantity Unit Rate in Words Amount
No. [Excluding GST]
8 Wiring for circuit/submain wiring along with earth wire with the
following sizes of FRLS PVC insulated copper conductor, single core
cable in surface/ recessed medium class PVC conduit as required.

a) 3 x 2.5 sq. mm (lighting & exhaust fans)

Rupees Two Hundred Eighty
160.00 Mtrs 284.52 Four and Fifty Two Paise 45523.20
Only

b) 3 x 4 sq. mm(For 16A power points & 20A powerpoints)

Rupees Three Hundred Forty
120.00 Mtrs 345.55 41466.00
Five and Fifty Five Paise Only

9 Supplying and fixing of following sizes of medium class PVC conduit

along with accessories in surface/recess including cutting the wall
and making good the same in case of recessed conduit as required.

a) 20MM PVC Conduit Rupees One Hundred Thirty

30.00 Mtrs 132.42 Two and Forty Two Paise 3972.60
Only
b) 25MM PVC Conduit

Rupees One Hundred Fifty

40.00 Mtrs 150.02 6000.80
and Two Paise Only

10 Earthing

a) Providing and fixing 6 SWG dia G.I. wire on surface or in recess for
loop earthing along with existing surface/ recessed conduit/ submain Rupees Forty Three and
70.00 Mtrs 43.46 3042.20
wiring/ cable as required. Forty Six Paise Only

11 Voice & LAN

Page 16
 NAME OF THE WORK: Construction of Shed to Raw Material for Outsourcing Department at LCA Plant – II at HAL [BC] – [Including Electrical Work].
CONTRACT NO. HAL/FMD/C-48/25-26

PRICE BID

Name of the Contractor : x

Sl. Rate in Figs

Specification Quantity Unit Rate in Words Amount
No. [Excluding GST]
a) Supply & fixing on wall/grouted to floor upto 1200mm above ground
level as per site requirement using suitable size MS angle iron frame
work finished with two coats of enamel spray paint over a good
primer & providing 10 pair krone type telephone connector junction
box including krone connector with necessary mounting frame housed 1.00 No 800.00 Rupees Eight Hundred Only 800.00
in suitable size FRP box with hinged lockable cover complete in all
respects.

b) Supply, laying in the already excavated cable trench/existing

duct/fixing on wall/cable tray/iron structure using suitable clamps
etc./ encasing in pipe, testing and commissioning of 10 pair jelly filled
armoured copper conductor of 0.5mm dia polyethylene insulated
cover, twisted into pairs, colour coded, pairs laid up, fully filled with
petroleum jelly as a moisture barrier, core wrapped with non-
hygroscopic polyester tape to contain the jelly, covered with 70.00 Mtrs 200.00 Rupees Two Hundred Only 14000.00
aluminium poly-laminates screen, polyethylene sheath extruded over
aluminium screen, polyethylene tape over the above sheath,
armoured with galvanised steel tape and outer polyethylene sheath
underground telecommunication cable including both end
terminations on the existing krone type junction box complete in all
respects.
c) Supply & drawing of 0.5 mm dia copper conductor PVC insulated 4
pair colour coded and twisted unarmoured telecommunication cables
Rupees Fifty Five and Eighty
in the existing PVC conduit as per standard practice including 80.00 Mtrs 55.87 4469.60
Seven Paise Only
necessary inter connections & end terminations.

d) Supply, Fixing, in flush with wall/on wall as per site condition,

suitable size modular GI box/PVC box with base plate, glossy front
cover for supply and housing of 1 No. of Twin RJ-11 telephone
socket outlets with shutter including supply of suitable size modular
Rupees One Hundred Fifty
type GI concealed/open PVC mounting box with base plates, front 2.00 Nos 153.12 306.24
Three and Twelve Paise Only
covers, etc., with necessary interconnections and chipping the wall,
replastering to smooth finish etc., wherever required complete as
directed by Engineer-in-charge.

e) Supply and drawing in the existing PVC conduits / wall / above false
ceiling, 2runs of Cat 6 UTP 4-Pair cable including necessary Rupees Ninety Nine and
interconnections complete for LAN & Internet point as directed by 145.00 Mtrs 99.32 14401.40
Thirty Two Paise Only
Engineer-in-charge.

Page 17
 NAME OF THE WORK: Construction of Shed to Raw Material for Outsourcing Department at LCA Plant – II at HAL [BC] – [Including Electrical Work].
CONTRACT NO. HAL/FMD/C-48/25-26

PRICE BID

Name of the Contractor : x

Sl. Rate in Figs

Specification Quantity Unit Rate in Words Amount
No. [Excluding GST]
f) Supply, Fixing in flush with wall/on Aluminium partition as per site
condition, testing & Commissioning of 2 nos of RJ-45 modular type
sockets for Data points including supply of suitable size modular
MS/PVC surface mounting box with base plates, glossy finish front
covers, labelling etc., with necessary interconnections and chipping 2.00 Nos 700.00 Rupees Seven Hundred Only 1400.00
the wall, replastering to smooth finish etc., wherever required
complete as directed by Engineer-in-charge.
Approved Make: COMMSCOPE TYCO/ PANDUIT/
MOLEX/Legrand/Schneider/HAL approved makes

12 Supply and laying of 63mm dia, PE-80, PN8 ISI marked HDPE pipe
confirming to IS 4984:19955 including suitable jointing using welding
as required in the excavated trench/duct/at road crossings for Rupees One Hundred Forty
40.00 Mtrs 140.38 5615.20
encasing cables complete in all respect as directed by Engineer-in- and Thirty Eight Paise Only
charge.

13 Supplying and fixing of 100 x 50 x 1.6mm size Hot dip galvanised

Perforated type cable tray, steel: As per IS:2062 / 1079, Galvanising :
As per IS: 2629 / 4759 including all accessories like base slotted
angle , horizontal elbow, horizontal tee, horizontal cross, horizontal Rupees Six Hundred Fifty
40.00 Mtrs 650.94 26037.60
reducer, vertical elbow up, inside, vertical elbow down, outside, and Ninety Four Paise Only
coupler plate, fasteners etc.
Note: MS supports will be paid separately.

14 Supply and fixing of weather proof cable junction box with terminals
of size 104 mm x 104 mm x 70 mm Hensel Cat. No. DK 0402 G or
equivalent in Legrand/ Schneider/ Hagar make only. The Box shall be
mounted on the truss using suitable size MS angle frame Rupees One Thousand One
work(including) with painting as per EIC, with cable entry knock-outs, 6.00 Nos 1156.78 Hundred Fifty Six and 6940.68
including rigid support for all components, Din channel, required Seventy Eight Paise Only
fasteners totally enclosed, dust and vermin proof and degree of
protection shall not be less than IP-65 complete in all respects and as
directed by Engineer-in-charge.
Civil items

15 Excavation in all types of soil for Cable trench including refilling,

consolidating of soil after laying the cable including ramming and
Rupees Five Hundred One
levelling to smooth finish as per the Technical specifications enclosed 5.00 [Link] 501.39 2506.95
and Thirty Nine Paise Only
and as directed by the Engineer-in-charge.

Page 18
 NAME OF THE WORK: Construction of Shed to Raw Material for Outsourcing Department at LCA Plant – II at HAL [BC] – [Including Electrical Work].
CONTRACT NO. HAL/FMD/C-48/25-26

PRICE BID

Name of the Contractor : x

Sl. Rate in Figs

Specification Quantity Unit Rate in Words Amount
No. [Excluding GST]
16 Concrete cutting/Chipping/Bitumen Road the existing [Link] or richer
mix cement concrete road /pavements / flooring / rock/stone etc., Rupees Two Thousand Three
including removing debris from the work site and taking out of the 1.00 [Link] 2368.53 Hundred Sixty Eight and Fifty 2368.53
division and depositing in the place as directed by EIC. Three Paise Only

17 Re-concreting the cut portion with [Link] cement concrete by

employing 20mm graded aggregate granite to smooth finish including Rupees Eight Thousand
curing and form work if any complete in all respects and as directed. 1.00 [Link] 8351.64 Three Hundred Fifty One and 8351.64
Sixty Four Paise Only

18 Design, Fabrication, Supply and fixing/grouting/welding on

wall/ceiling/truss of suitable size MS angle iron supports/ flat/
brackets for light fixture and cable tray supports, as per site Rupees One Hundred
requirement and painting the same with two coats of synthetic 40.00 Kgs 114.18 Fourteen and Eighteen Paise 4567.20
enamel paint over a coat of zinc chromite primer complete in all Only
respects and as directed by EIC/OIC.

19 Supply and laying of 80mm dia class B [Link] for encasing cable
across the road/ drain/cble duct entry for encasing the cable and as Rupees One Thousand One
per standard practice & as directed by Engineer-in-charge. 20.00 Mtrs 1142.15 Hundred Forty Two and 22843.00
Fifteen Paise Only

Rupees Four Lakh Fourteen Thousand Nine Hundred Eighty Eight and
Sub-Total of 'II' - Electrical Works (Excluding GST) 414988.76
Seventy Six Paise Only

Rupees Seventy Nine Lakh Sixty Eight Thousand Three Hundred Twenty
Total of Part 'I' + 'II' (Excluding GST) 7968322.33
Two and Thirty Two Paise Only

Approximate
The Tenderer has to Quote Percentage Above / Below as Specified and State Above Percentage
Amount Put to Amount
Percentage Shall be Quoted in Figures. or Below in Figures [Excluding GST]
Tender

Tenderer's Quote (Excluding GST) 7968322.33 BELOW % 7968322.33

Rupees Fourteen Lakh Thirty Four Thousand Two Hundred Ninety Eight
Add 18% GST 1434298.02
and One Paise Only

Page 19
 NAME OF THE WORK: Construction of Shed to Raw Material for Outsourcing Department at LCA Plant – II at HAL [BC] – [Including Electrical Work].
CONTRACT NO. HAL/FMD/C-48/25-26

PRICE BID

Name of the Contractor : x

Sl. Rate in Figs

Specification Quantity Unit Rate in Words Amount
No. [Excluding GST]

Rupees Ninety Four Lakh Two Thousand Six Hundred Twenty and Thirty
Grand Total (Including GST) 9402620.34
Four Paise Only

Note: The tenderer has to quote percentage above / below against the total amount considering the specified standard rates. If the contractor does not quote any percentage
above / below on the total amount, the tender shall be treated as invalid and will not be considered.

WARNING: PLEASE ENTER PERCENTAGE QUOTE

Page 20