Data Sheet FCDUOFEEN

Duo-Fine® E Series
Filter Cartridges

High Capacity Pleated Filter Cartridges

With Microfiberglass Media
• Unique microfiberglass media provides exceptional
dirt-holding capacity for longer service life
• 304 stainless steel center core and end caps available
for high temperature applications
• Small diameter fibers ensure high flow rates at low
pressure drops
• Economical alternative to stringwound cartridges
• Available in retention ratings of 0.2 to 50 microns (μm)
• Protective netting is color-coded for easy identification
of micron ratings
• End configurations to fit most housings
• Core material options for different temperature
compatibility

Performance Specifications
Filter grades
0.2, 0.45, 1, 3, 10, 30, 50 μm Product Specifications
Recommended change-out differential pressure 1 Materials of construction
2.4 bard (35 psid) Filter media:
50 μm: Spunbonded polyester
Maximum differential pressure
All other grades: Borosilicate microfiberglass with
Polypropylene hardware
acrylic binder
4.8 bard (70 psid) @ 20°C (68°F)
Support material: Spunbonded polyester
2.8 bard (40 psid) @ 65˚C (150˚F)
Netting: Polypropylene
304 stainless steel hardware Hardware: Polypropylene or 304 stainless steel 2
5.2 bard (75 psid) @ 121°C (250°F) Sealing: Thermal bond
Sterilization Gaskets/O-rings: Silicone elastomer, nitrile,
All Duo-Fine E Series cartridges may be autoclaved for fluorocarbon elastomer,
30 minutes at 121°C (250°F) under no end load conditions. hydrocarbon rubber, FEP
Cartridges with 304 stainless steel core and end caps encapsulated silicone, expanded
may be steamed in-line at 121°C (250°F) for up to one PTFE, white nitrile, white silicone
hour. Do not reverse flow under steam conditions, damage Dimensions (nominal)
to the filter may occur. Outside Diameter: 6.6 cm (2.6 in)
Lengths: 10.2 cm (4 in), 24.8 cm (9.75 in),
25.4 cm (10 in), 49.5 cm (19.5 in),
50.8 cm (20 in), 74.3 cm (29.25 in),
1 Provided that the maximum differential pressure is not exceeded based
76.2 cm (30 in), 99.1 cm (39 in),
on temperature limits defined above. 101.6 cm (40 in)
2 304 stainless steel end caps are epoxy bonded.
Color Code Chart For Duo-Fine E Series Duo-Fine E Series filter cartridges have been
Netting Color Micron Rating extensively laboratory and field tested to determine
removal efficiencies in the most stringent of operating
Green 0.2
conditions.
Yellow 0.45
The removal rating of any filtration device will depend
White 1 on, to some extent, the conditions under which it is
Blue 3 used or tested. The test results will be influenced by
Red 10 the nature of the fluid, its viscosity, the flow rate, the
Purple 30
type of contaminant, and the temperature.

Orange 50
The ratings given represent the diameter of the largest
hard spherical particle that will pass through the filter
during standard test. Contact Pall for a complete
Particle Retention (µm) description of Pall's test procedures.
Liquid Service Gas Service
(by ASTM F-795 Test)
The DOP test measures the ability of the filter to capture
fine droplets in air or gas. The retention ratings given
Cartridge 90% >99.9% Removal
Designation Efficiency Efficiency Efficiency represent the removal efficiencies with respect to an
by DOP Test aerosol dispersion of 0.3 μm Dioctyl Phthalate (DOP)
DFN 0.2 0.2 1.0 99.999% particles.
DFN 0.45 0.45 2.0 99.998%
DFN 1 1.0 4.0 96% Typical Flow vs. Differential Pressure for Application
Sizing
DFN 3 3.0 10.0 _________
Flow rate (lpm), water at 20°C
DFN 10 10.0 18.0 _________ 0 8 15 23 30 38
_________ 3.0 0.20
DFN 30 30.0 45.0
DFN 50 50.0 75.0 _________ 2.5
0.15

Differential pressure (bard)

Differential pressure (psid)

2.0

1.5 0.10

1.0
0.05
0.5

0 0
2 4 6 8 10
Flow rate (gpm), water at 68°F

Unit conversion: 1 bar = 100 kPa

Flow rate is for a 25.4 cm (10 in) cartridge. For liquids other than water, multiply
differential pressure by fluid viscosity (cP).
Ordering Information
Pall Part Number = DFN 1 – 2 3 4 – 5 6 7

Table 1 Table 3 Table 5

Code Filter Code Core Code End configurations
grades (µm) materials
0.2 0.2 U Polypropylene Blank DOE with elastomer gasket seals & end caps
0.45 0.45 A 304 stainless 1X DOE, 2.54 cm (1 in) extended core
steel M2 SOE flat closed end, fits housings with 020
1 1
O-ring post (polypropylene hardware only)
3 3 M3 SOE flat closed end, external 222 O-rings
10 10 Table 4 (retrofits other manufacturers’ Code 0) 3
(polypropylene hardware only)
30 30 Code Gasket/O-ring
M5 DOE internal 120 O-rings
50 50 materials
(retrofits 213 O-ring style)3
S Silicone (polypropylene hardware only)
N Nitrile M6 SOE flat closed end, external 226 O-rings
Table 2 (retrofits other manufacturers’ Code 6) 3
E Hydrocarbon (polypropylene hardware only)
Code Cartridge rubber
M7 SOE fin end, external 226 O-rings
lengths (cm / in) V Fluorocarbon (retrofits other manufacturers’ Code 7) 3
nominal elastomer (polypropylene hardware only)
4 10.2 / 4 T FEP encapsulated M8 SOE fin end, external 222 O-rings
9.75 24.8 / 9.75 silicone (O-rings) (retrofits other manufacturers’ Code 5) 3
(polypropylene hardware only)
10 25.4 / 10 M White silicone
M10 DOE internal O-rings (fits other manufacturers’
19.5 49.5 / 19.5 W White nitrile housings) 3 (polypropylene hardware only)
(gaskets)
20 50.8 / 20 M11 SOE flat closed end, internal 120 O-ring
X No O-ring (retrofits other manufacturers’ X style) 3
29.25 74.3 / 29.25 required (polypropylene hardware only)
30 76.2 / 30 (M2 style only)
39 99.1 / 39 T Expanded PTFE
(gaskets)
40 101.6 / 40 Table 6 Table 7
3 For details, contact Pall
Corporation.
Code Bubble test Code Packaging
option
Blank Sample bubble Blank Standard
tested packaging
B 100% bubble test -BLK Bulk packaging3

Fuels and Chemicals Visit us on the Web at [Link]

25 Harbor Park Drive Pall Corporation has offices and plants throughout the world. For Pall representatives in your
Port Washington, NY 11050 area, please go to [Link]/contact.
+1 516 484 3600 telephone Because of technological developments related to the products, systems, and/or services
+1 888 873 7255 toll free US described herein, the data and procedures are subject to change without notice. Please
consult your Pall representative or visit [Link] to verify that this information
remains valid.

© Copyright 2005, 2012, Pall Corporation. Pall, , and Duo-Fine are trademarks of Pall Corporation.
® Indicates a Pall trademark registered in the USA. Filtration. Separation. [Link] is a service mark of Pall
Corporation.

FCDUOFEEN Produced in the USA June 2012