SHEET METALWORKING
2002 John Wiley & Sons, Inc. M. P. Groover, Fundamentals of Modern Manufacturing 2/e
SHEET METALWORKING
1.
Cutting Operations
2.
3. 4.
Bending Operations
Drawing Sheet Metal Operations Not Performed on Presses
Sheet Metalworking Defined
Cutting and forming operations performed on relatively thin sheets of metal Thickness of sheet metal = 0.4 mm (1/64 in) to 6 mm (1/4 in) Thickness of plate stock > 6 mm Operations usually performed as cold working
Sheet and Plate Metal Products
Sheet and plate metal parts for consumer and industrial products such as
Automobiles and trucks Airplanes Railway cars and locomotives Farm and construction equipment Small and large appliances Office furniture Computers and office equipment
Advantages of Sheet Metal Parts
High strength Good dimensional accuracy Good surface finish Relatively low cost For large quantities, economical mass production operations are available
Sheet Metalworking Terminology
1.
Punch-and-die
Tooling to perform cutting, bending, and drawing
Machine tool that performs most sheet metal operations Sheet metal products
2.
Stamping press
3.
Stampings
Three Major Categories of Sheet Metal Processes
1.
Cutting
Shearing to separate large sheets; or cut part perimeters or make holes in sheets
2.
Bending
Straining sheet around a straight axis
3.
Drawing
Forming of sheet into convex or concave shapes
7
I. Cutting
Shearing between two sharp cutting edges
Shearing, Blanking, and Punching
Three principal operations in pressworking that cut sheet metal: Shearing Blanking Punching
Shearing
Sheet metal cutting operation along a straight line between two cutting edges Typically used to cut large sheets into smaller sections for subsequent operations
10
Blanking and Punching
Blanking - sheet metal cutting to separate piece from surrounding stock Cut piece is the desired part, called a blank Punching - sheet metal cutting similar to blanking except cut piece is scrap, called a slug Remaining stock is the desired part
(a) Blanking and (b) punching
11
Clearance in Sheet Metal Cutting
Distance between the punch and die Typical values range between 4% and 8% of stock thickness
If too small, fracture lines pass each other, causing double burnishing and larger force If too large, metal is pinched between cutting edges and excessive burr results
12
II. Bending
Straining sheetmetal around a straight axis to take a permanent bend
(a) Bending of sheet metal
(b) both compression and tensile elongation of the metal occur in bending
13
Types of Sheetmetal Bending
V-bending - performed with a V-shaped die Edge bending - performed with a wiping die
14
V-Bending
For low production Performed on a press brake V-dies are simple and inexpensive
15
Edge Bending
For high production Pressure pad required Dies are more complicated and costly
16
Springback in Bending
Springback = increase in included angle of bent part relative to included angle of forming tool after tool is removed Reason for springback:
When bending pressure is removed, elastic energy remains in bent part, causing it to recover partially toward its original shape
17
III. Drawing
Sheet metal forming to make cup-shaped, box-shaped, or other complex-curved, hollow-shaped parts
Products: beverage cans, ammunition shells, automobile body panels
18
IV. Shapes other than Cylindrical Cups
Square or rectangular boxes (as in sinks), Stepped cups, Cones, Cups with spherical rather than flat bases, Irregular curved forms (as in automobile body panels)
Each of these shapes presents its own unique technical problems in drawing
19
Ironing Makes wall thickness of cylindrical cup more uniform Examples: beverage cans and artillery shells
Ironing to achieve a more uniform wall thickness in a drawn cup:
(1) start of process; (2) during process Note thinning and elongation of walls
20
Embossing Used to create indentations in sheet, such as raised (or indented) lettering or strengthening ribs
Embossing: (a) cross-section of punch and die configuration during pressing; (b) finished part with embossed ribs
21
Guerin Process
Advantages of Guerin Process Low tooling cost Form block can be made of wood, plastic, or other materials that are easy to shape Rubber pad can be used with different form blocks Process attractive in small quantity production
22
Dies for Sheet Metal Processes
Most pressworking operations performed with conventional punch-and-die tooling
The term stamping die sometimes used for high production dies
23
Dies for Sheet Metal Processes
(a) (b)
Progressive die; associated strip development
24
Several sheet metal parts produced on a turret press, showing variety of hole shapes possible (photo courtesy of Strippet, Inc.)
25
Power and Drive Systems
Hydraulic presses - use a large piston and cylinder to drive the ram
Longer ram stroke than mechanical types Suited to deep drawing Slower than mechanical drives
Mechanical presses convert rotation of motor to linear motion of ram
High forces at bottom of stroke Suited to blanking and punching
26
Sheet Metal Operations Not Performed on Presses
1.
2. 3.
4.
Stretch forming Roll bending and forming Spinning High-energy-rate forming processes.
27
1. Stretch Forming
Sheet metal is stretched and simultaneously bent to achieve shape change
Stretch forming: (1) start of process; (2) form die is pressed into the work with force Fdie, causing it to be stretched and bent over the form. F = stretching force
28
2. Roll Bending Large metal sheets and plates are formed into curved sections using rolls
Roll bending
29
2. Roll Forming Continuous bending process in which opposing rolls produce long sections of formed shapes from coil or strip stock
Roll forming of a continuous channel section: (1) straight rolls (2) partial form (3) final form
30
3. Spinning
Metal forming process in which an axially symmetric part is gradually shaped over a rotating mandrel using a rounded tool or roller
Conventional spinning: (1) setup at start of process; (2) during spinning; and (3) completion of process
31
4. High-Energy-Rate Forming (HERF)
Processes to form metals using large amounts of energy over a very short time HERF processes include:
Explosive forming Electrohydraulic forming Electromagnetic forming
32
Explosive Forming
Use of explosive charge to form sheet (or plate) metal into a die cavity Explosive charge causes a shock wave whose energy is transmitted to force part into cavity Applications: large parts, typical of aerospace industry
Explosive forming: (1) setup, (2) explosive is detonated, and (3) shock wave forms part and plume escapes water surface
33
Electromagnetic Forming
Sheet metal is deformed by mechanical force of an electromagnetic field induced in workpart by an energized coil Presently the most widely used HERF process Applications: tubular parts
Electromagnetic forming: (1) setup in which coil is inserted into
tubular workpart surrounded by die; (2) formed part
34
