Components of HVAC System

While these five loops can be used to describe virtually any

HVAC system, not every system uses all five loops.
• The purpose of this period is to provide a method
for understanding the components of different
types of HVAC systems.
• The premise of this method is that any HVAC
system can be dissected into basic subsystems.
• These subsystems will be referred to as “loops.”
• There are five primary loops that can describe
virtually any type of HVAC system.
• The first loop is the airside loop, and the first
component of this loop is the conditioned space.
• The first two comfort requirements mentioned were
dry bulb temperature and humidity.
• In order to maintain the dry-bulb temperature in the
conditioned space, heat (referred to as sensible heat)
must be added or removed at the same rate as it leaves
or enters the space.
• In order to maintain the humidity level in the space,
moisture (sometimes referred to as latent heat) must
be added or removed at the same rate as it leaves or
enters the space.
Supply Fan and Filter

•The othercomponent of the

airside loop is a supply fan that
delivers the supply air (SA) to
the space.
Cooling Coil
• A heat exchanger, commonly known as a cooling
coil, is often used to cool and dehumidify the
supply air before it is delivered to the space.
• A typical cooling coil includes rows of tubes
passing through sheets of formed fins.
• A cold fluid, either water or liquid refrigerant,
enters one header at the end of the coil and then
flows through the tubes, cooling both the tubes
and the fins.
Chilled-Water Cooling Coil
 Fan-Coil Unit
• A simple example of the airside loop is a fan-coil
unit.
• Return air from the space is drawn into the unit
at the base and can be mixed with outdoor air
that enters through a separate damper in the
back of the unit.
• This mixed air passes through a filter, a supply
fan, and a cooling coil before being discharged
from the top of the unit, directly into the
conditioned space.
Fan-Coil Unit
 Central Air Handler
• Another example of the airside loop is a central air-
handling system.
• A central air handler is typically installed outside of the
conditioned space, possibly on the roof or in a
dedicated mechanical room.
• Return air from the space is drawn into the unit
through the return-air dampers and mixes with
outdoor air that enters through another set of
dampers.
• This mixed air passes through the filters, the supply
fan, and the cooling coil before being discharged from
the air handler.
•Unlike the example fan-coil unit that was installed in the conditioned
space, the central air handler needs a method for delivering the supply
air to the conditioned space(s).
 Supply-Air Distribution System
• A supply-air distribution system, typically constructed
of sheet-metal ducts, fittings, and diffusers, is used to
direct the supply air from the central air handler to one
or more conditioned spaces.
• From each VAV terminal unit, the supply air travels
through a section of flexible duct to remotely located
diffusers.
• Diffusers are used to distribute the supply air
effectively to the conditioned space.
• Proper air diffusion is an important comfort
consideration, especially in VAV systems, to avoid
dumping cold supply air on the occupants of the space.
The plenum is the space between the ceiling and the
roof, or floor, above.
 Chilled-Water Loop
• In the airside loop, a cooling coil is used to
cool and dehumidify the supply air.
• As mentioned, the cold fluid flowing through
the tubes of the coil may be either water or
liquid refrigerant.
• Systems that use water flowing through the
cooling coil also contain a chilled-water loop.
 Evaporator
• It has also been mentioned that the water
flowing through the cooling coil must be
colder than the air passing through it.
• This heat exchanger, called an evaporator, is
one component of the refrigeration (cooling)
equipment.
 Pump and Control Valve
• The other component of the chilled-water loop is a
pump that moves water around the loop.
• This pump needs to have enough power to move the
water through the piping, the evaporator, the tubes of
the coil, and any other accessories installed in the
chilled-water loop.
• Similar to the airside loop, the chilled-water loop
responds to changing cooling loads by varying either
the temperature or the quantity of water delivered to
the cooling coil.
• The most common method, however, is to vary the
quantity of water flowing through the cooling coil by
using a control valve.
•As the cooling load decreases, the modulating control valve reduces
the rate of chilled-water flow through the coil, decreasing its cooling
capacity.
An example of a system that does not use the
chilled-water loop is one that uses a packaged
rooftop air conditioner
 Heat-Rejection Loop
• The fourth loop is the heat-rejection loop.
• In the refrigeration loop, the condenser transfers heat
from the hot refrigerant to air, water, or some other fluid.
• In a water-cooled condenser, water flows through the tubes
while the hot refrigerant vapor enters the shell space
surrounding the tubes.
• Heat is transferred from the refrigerant to the water,
warming the water.
• The water flowing through the condenser must be colder
than the hot refrigerant vapor.
• When a water-cooled condenser is used, this heat
exchanger is typically either a cooling tower or a fluid
cooler (also known as a dry cooler).
 Controls Loop
• The fifth, and final, loop of the HVAC system is the controls loop.
• Each of the previous four loops contains several components.
• Each component must be controlled in a particular way to ensure
proper operation.
• Typically, each piece of equipment (which may be comprised of one
or more components of a loop) is equipped with a unit-level,
automatic controller.
• In order to provide intelligent, coordinated control so that the
individual pieces of equipment operate together as an efficient
system, these individual unit-level
• controllers are often connected to a central, system-level
controller.
Finally, many building operators want to monitor the system,
receive alarms and diagnostics at a central location, and integrate
the HVAC system with other systems in the building. These are
some of the functions provided by a building automation system
(BAS).