Wiring Design Of Dr.
MA Rashid
Hall 1st Floor:
•Dining Room
•TV Room
•Provost Office
•Kitchen
•Toilets
Course Teachers
Dr. Md. Tawabur Rahman
Associate Professor
Department of Electrical & Electronic Engineering
Khulna University of Engineering & Technology(KUET)
Md. Sajjad Hossain
Lecturer
Department of Electrical & Electronic Engineering
Khulna University of Engineering & Technology (KUET)
Team Members
Team Members
NAME ROLL
MD. GOLAM RABBI 2201067
MD. TARIKUL ISLAM 2201068
MD. MAHIN SIDDIQUE 2201069
AMLAN MALLICK 2201070
ASFAQUR RAHMAN TAMIM 2201071
MD MAHMUDUL HASAN 2201072
SEFAT
Provided project:
C.T.S wiring will be used to wire Dinning Room, TV Room, Provost
Office, Kitchen and Toilets of Dr. MA Rashid Hall of KUET, where at the
entrance, there is a TV Room. It features a television jack. Then
provost office of Dr. MA Rashid Hall is equipped with a computer
desk , air condition [Link] is a common room with an attached
bathroom for teachers. Utilize double fluorescent ceiling lamps in
classrooms and single fluorescent ceiling lamps in the teachers'
lounge. The teacher's room is equipped with a telephone (PSTN) and a
T.V. socket outlet. The teacher's restroom must have an exhaust fan.
In addition, the coaching facility has four restrooms, where exhaust
fans are recommended. Except for the restrooms, each of the rooms,
as mentioned earlier, has a sub-distribution board, whereas the
department's main distribution board is found at the entrance.
Assumptions:
Utilization factor(U.F)= 0.6
Depreciation Factor(D.F) = 0.8
Floor Height is 10ft .
Conduit and wires are calculated with 5% extra quantity.
Loads are calculated with 20% additional load.
Estimation for the wire size of residential flat is assumed to
be perfect up to 40° 𝐶
Light efficiency : 1. For LED Light- 100 lumen/watt
2. For Double fluorescent light- 87.5
lumen/watt
[Link] Single fluorescent light-85 lumen/watt
Electrical Elements Position
& Symbols:
Symbols used for Electrical Drawing Ceiling
Main Distribution Board 3 pin Socket Outlet
(MDB) (single phase) LED Light (Bathroom), Speaker, 3
2' pin socket outlet (for AC) (Single
Sub-Distribution Board
phase)
(SDB) Exhaust Fan 1' Exhaust Fan
TV Microphone 2'
Ceiling Fan 10'
Main Distribution
T
TV
T
TV Socket Outlet Board(MDB), Sub-
LED Light 3'
distribution Board(SDB), TV
Double Fluorescent Lamp Telephone Outlet
socket outlet
on Celling 2 pin socket outlet,
Single Fluorescent Lamp (PSTN) Microphone, Telephone
on Celling Outlet (PSTN) (Single phase)
Speaker
2 pin Socket Outlet
(single phase) Floor Level
Project Output:
To apply the knowledge of electrical engineering
To know about perfect wire selection
To design floor plan for building
To know about standard illuminance of different rooms
To estimate cost of different electrical elements and wires
efficiently
Necessary Electrical Elements:
Dr. MA RASHID Hall will be electrified using C.T.S wiring. The details of the
electrical elements required are shown as follows:
Rooms Size Total lumen Ceilin Exha A.C
SL. required g Fan ust
NO Fan
.
1. Dining Room 55’1”*20’ 31994.23 10
2. TV Room 35’1”*28’10 29224.34 3
”
3. Provost Office 28’*21’4” 34804.78 3 1
4. Kitchen 20’1”*18’7" 14935.78 2
Store-1 8’1”*6’4” 1075.3
Store-2 4’*6’4” 482.38
Pantry 12’5”*12’6” 3048.28 1
lan with Electrical Elements:
Building Plan with wiring to load:
Light Calculation Formula
𝐷𝑒𝑝𝑟𝑒𝑐𝑖𝑎𝑡𝑖𝑜𝑛
Area([Link])*Illumination(ft-cd)
Total lumen required =
𝑓𝑎𝑐𝑡𝑜𝑟∗𝑈𝑡𝑖𝑙𝑖𝑧𝑎𝑡𝑖𝑜𝑛 𝑓𝑎𝑐𝑡𝑜𝑟
Wattage
𝐿𝑢𝑚𝑖𝑛𝑜𝑢𝑠 𝑒𝑓𝑓𝑖𝑐𝑖𝑒𝑛𝑐𝑦
Total lumen required
=
Known Values:
Depreciation Factor 0.8
Utilization Factor 0.6
Dimensions
Illuminance
Light
SL Calculation:
Rooms Size Total No. Of
No ([Link]) Wattage(W) Lamps
1 Dining Room 55’1”*20’ 320W 8 Pieces
2 TV Room 35’1”*28’1 280W 7 Pieces
0”
3 Provost Office 28’*21’4” 320W 4 Pieces
4 Kitchen Room 20’1”*18’7 160W 4 Pieces
"
Store-1 8’1”*6’4” 10W 1 Pieces
Store-2 4’*6’4” 5W 1 Pieces
Pantry 12’5”*12’6 30W 1 Pieces
”
Conduit Length Calculation:
(From Main distribution board to sub distribution board)
Place Conduit Length(ft)
From To(sub distribution
board)
Dining Room 196
TV Room 10
Main distribution Provost Office 59
board Store 1 210
Store 2 206
Pantry 206
Toilet Block 196
Kitchen 196
Total 1279
Conduit Length Calculation:
(Sub distribution board to electrical element)
Place Conduit Length(ft)
From To Load
Dining Room 330
TV Room 177
Sub distribution Provost Office 172
board Store 1 90
Store 2 90
Pantry 84
Toilet Block 72
Kitchen 74
TOTAL 889
Wire Length Calculation:
(Main distribution board to electrical element)
Place Wire
From To(sub distribution board) Length(ft)
Dining Room 400
TV Room 25
Main Provost Office 120
distribution Store 1 430
board Store 2 435
Pantry 415
Toilet Block 400
Kitchen 400
TOTAL 2625
Wire Length Calculation:
(Sub distribution board to electrical element)
Place Wire Length(ft)
From To Load
Dining Room 680
TV Room 360
Sub distribution Provost Office 345
board Store 1 200
Store 2 200
Pantry 170
Toilet Block 145
Kitchen 155
TOTAL 2255
Cost Estimation
Table 1 :Cost for Wire & Conduit
Name of items Quantity(ft) Rate (TK Cost (Tk)
Per ft. )
Specification
1/1.40 2255 5.5 12,402
Wire
7/2.50 2625 45 118,125
Conduit 2168 20 43,360
TOTAL 173,887
Adding 5% of wire & Conduit :
For Wire :2255+2625+244=5124
For Conduit:2168+108.4=2276.4
Table 2 : Cost for Accessories
Name Of Items Quantity Unit Price(Tk) Cost(Tk)
Single Flourescent Ceilling 40W(x15) 460 6900
Light
80W(x4) 950 3800
40W (x4) 820 3280
30W (x1) 650 650
LED Light 15W (x4) 430 1720
10W (x1) 350 350
5W (x1) 295 295
AC 1(1.5 ton) 70000 70000
Ceiling Fan 17 (70W) 2950 50150
Exhaust Fan 2(36W) 1450 2900
MDB 1 49000 49000
SDB 3 25000 75000
Switch 48 650 31200
Total Cost With Additional Wire
& Conduit:
Costing Cost(Tk)
Additional Wire & 8694
Conduit
Labour Wage 42000
Overall Cost 519826
“THANK YOU”
