Control and Power Management in HRES System

International Journal of Trend in Scientific Research and Development (IJTSRD)
Volume 4 Issue 4, June 2020 Available Online: www.ijtsrd.com e-ISSN: 2456 – 6470
@ IJTSRD | Unique Paper ID – IJTSRD31150 | Volume – 4 | Issue – 4 | May-June 2020 Page 609
Control and Power Management in HRES System
Majid Hussain
M. Tech Scholar, Electrical Engineering,
GRD Institute of Management and Technology Dehradun, Dehradun, Uttarakhand, India
ABSTRACT
A novel energy control strategy for a battery/super capacitor in HRES, which
is designed to be tunable to achieve different goals, is described. Twopossible
goals for adding a pack of super capacitors are examined for a test micro grid
using lead-acid batteries: 1) improving the microgrid’sefficiency and range
and 2) reducing the peak currents in the battery pack to increase battery life.
The benefits of hybridization are compared with those achievable by
increasing the size of the battery pack by a comparable mass to the super
capacitors. The availability of energy from regenerative braking and the
characteristics of the super capacitors are considered asimpactfactors.Super
capacitors were found to be effective at reducing peak battery currents;
however, the benefits to range extension were found to be limited. A battery
life extension of at least 50% is necessary to make super capacitors cost
effective for the test vehicle at current prices.
How to cite this paper: Majid Hussain
"Control and Power ManagementinHRES
System" Publishedin
International Journal
of Trend in Scientific
Research and
Development
(ijtsrd), ISSN: 2456-
6470, Volume-4 |
Issue-4, June 2020,
pp.609-614, URL:
www.ijtsrd.com/papers/ijtsrd31150.pdf
Copyright © 2020 by author(s) and
International Journal ofTrendinScientific
Research and Development Journal. This
is an Open Access article distributed
under the terms of
the Creative
CommonsAttribution
License (CC BY 4.0)
(http://creativecommons.org/licenses/by
/4.0)
I. INTRODUCTION
Todays also there are very large area of world especially in
rural area still not have the access of electricity from the grid
partly due to high cost and partly due to their remote
location. In those areas, the electricity needs of the residents
are generally fulfilled by diesel engine generators which is
not a viable option as the remote areas are full of RERs
potential. Recently, hybrid renewable energy systems
(HRESs), combination of different types of renewableenergy
resources (RERs) along with the storage devices of different
characteristics come into play forprovidingelectricityforthe
areas where grid electricityisnotavailable[1]–[4].Almostall
the RERs are freely available and have advantages like
environment friendliness, and available in abundance. The
RERs can be used in combinations where the different RERs
are so selected that they can complement each other. Such a
combination is wind-solar combination, where the
shortcomings of one RER is overcome by other RER. This
combination of different RERs not only can increase the
reliability of the system but also reduce theoverallprice.[5]–
[9] Also it is well documented that without the support of
grid, HRES only cannot provide the enough inertia to the
entire system in order to keep frequency and voltage within
limits. So, ESSs are needed to overcome this problem. [10]
Therefore, ESS along with major constituent of HRES also
constitutes the large share of capital investment. [11]–[13]
Therefore, investment in the HRES mainly dependent on the
various particulars of the HRES and ESSs being the forth
runner in terms of cost decides the overall cost of the HRESs
and that can be limited by suitably selecting the proper sizes
of the different components of HRES. This not can reduce the
overall cost but also helps in increasing the operating livesof
the ESSs. [14]
As per the previous literature and widespread applications,
battery energy storage system (BESS) can be assumed to be
most popular and mature type of ESSs available in today’s
scenario. [15] But, as far as single use of ESS considering
BESS, can harm the operating life of BESS very significantly
because of rapid charge and discharge of it due to variations
in the output of RERs as well as variations in the load
requirement. [16], [17] Some domestic appliances require
very large amount of power only for significantly small time
like water pump motor that requires almost ten times of the
normal current only for 2-4 seconds. Asa result, therequired
capacity of BESS increases and that can led to the increase in
the investment cost. Consequently, larger size of BESS is
needed to supply this surge in the current which again
increases the overall cost of the system. By utilizing the
different ESSs consequently can help in solving this problem
which formulate the new concept of Hybrid energy storage
system (HESS) using the ESSs in such a way that they can
complement each other. [18]–[21] Depending on the
requirement of energy and power by the load, ESSs are
categorized in two types. One type of ESS can provide high
amount of power in short time termed ashighpowerESSand
second type can provide small amount of power but on
longer time that is high energy ESS. By joining these two
types of ESSs, one can fulfill the power and energy
requirements of all the loads by suitably selecting the high
power and high energy ESS. Currently, a lot of ESSs available
IJTSRD31150

International Journal of Trend in Scientific Research and Development (IJTSRD) @ www.ijtsrd.com eISSN: 2456-6470
possessing wide range of operationalcharacteristicsinterms
of technical and economic point of view for example
compressed air energy storage-battery, battery-fuel cell,
battery-supercapacitor, battery-flywheel and battery-
superconducting magnetic energy storage system (SMES)
formulates the generally hybridized components of HESSsin
HRES[22]. [23]–[29].
Considering the shortcomings of the various control
strategies presented in the literature review, a new and
enhancedcontrol scheme is presented in this thesis work for
a HRES consisting of WT and PV system. BESS and SCESS are
the parts of HESS and following purposes are fulfilled by the
proposed control scheme:
1. To achieve power balance in the various constituents of
the hybrid renewable energy system.
2. To maintain the DC link voltage within the prescribed
limits whatever be the wind speed, solar irradiance and
demand in electricity.
3. To maintain the power sharing utilizing the operational
characteristics BESS and SCESS in such a way that the
ESS can work on to their full potentialwithoutsacrificing
their operating life.
4. To maintain the frequency as well as the AC voltage
within limits.
II. Control Scheme
The generated electricity by PV system and WECS put
together and electricity consumed bytheloadisgoverned by
HESS control scheme. Based upon that there are two modes
of operation and are explained as:
1. Surplus power mode (SPM)
In SPM, the generation is more than the demand and the so
available surplus power, after serving the critical and non-
critical load, is used to charge the HESS until it gets charged
to its upper SoC limits. This involves the separation of low
and high frequency components of imbalance power and
their utilization, respectively, for charging the BESS and
SCESS which reduces the stress on BESS. Once the HESS gets
charged to its upper SoC limits, the excess power, still
available, is then diverted to the dump load to maintain the
power balance.
2. Deficit power mode (DPM)
In this mode, generation is less than the demand and the
deficit in the power is compensated by HESS until it touches
down to its lower SoC limits. This mode also involves the
separation of low and high frequency components of
imbalance power and their utilization, respectively, for
discharging the BESS and SCESS for the same purpose of
reducing the stress on BESS. The ratings of the HESS are so
selected that the supply to the critical load is ensured at all
the times. But in worst case scenario,whentheHESSreaches
to its lower SoC limits, load shedding option of non-critical
load is activated with the system serving only the critical
load.
The proposed HESS control strategy is explained with the
help of a block diagram as shown in Figure 1 As
aforementioned, in order to achieve longer operating life of
BESS, it’s deep charging and discharging is avoided and
allowed to operate only within its SoC limits. On the other
hand, SCESS can be fullychargedanddischargedwithout any
significant problems. As can be seen from the Figure2, when
the BESS is within its operating SoClimits,theerrorbetween
the actual VDC and reference DC link voltage (VDC
*) goes as
input to proportional-integral (PI) controller which in turn
gives as output the total reference current (I DC
*) for the
HESS. The IDC
* is then given as input to the LPF which filters
out, as a function of LPF (fLPF( )) as givenbyequation(1),the
low frequency components (IL_freq
*) from IDC
*:
* *
_ ( )L freq LPF DCI f I=
(1)
IL_freq
* current is passed from rate-limiter for achieving the
BESS reference current (IBat
*) The rate for BESS charging as
well as discharging is control by rate limiter and presented
by the equation (2):
* *
_( )Bat RL L freqI f I=
(2)
For reducing the error between the reference andmeasured
currents of BES another PI controller is utilized. The PI
controller feeds input to the PWM controller in order to
generate the command for BESS’s converter and is given by
duty ratio (DBat).
The high frequency components are filtered out from the
total current and given as by the equation (3).
* * *
_ _H freq DC L freqI I I= −
(3)
As discussed in previous chapters, the dynamics of BESS is
not as fast of SCESS so reference battery current cannot
tackle the fast change, So, uncompensated power (PB_uncomp),
as obained as per (4), is provided by SCESS and thesignal for
the same is formulated as per (5).
( )*
_ _ _B uncomp H freq B er r BatP I I V= + ×
(4)
( )_* *
_ _
B uncomp Bat
SC H freq B err
SC SC
P V
I I I
V V
= = + ×
(5)
Where,
VBat and VSC are output voltage of the battery and
supercapacitor units.
Same process is repeated for the SCESS where the error
signal obtained from the fLPF is utilized and PI controller
generated the duty cycle for the SCESS’s converter circuit
and which further produce the signals for the PWM
converter.
When there is excess power is available firstly utilized to
increase the SoC of BESS and SCESS and when their SOC
reached up to to highest level then that excess power is fed
to the dump load. On the other hand when there is shortage
of power exists, that shortage is overcome by HESS until
their SOC drops down to their lowest limits.

VDC
+
-
PI LPF
Rate
limiter
IDC
*
IBat
*
IBat
+
-
VDC
*
+
-
+
+
IL_freq
*
VBat
VSC
PI
+
-
ISC
PI
ISC
*
SBat,1-2
SSC,1-2
IH_freq
*
PWM
PWM
<
0
SDump
IBat_err
PI PWM
DBat
DDump
DSC
>
0
AND
SoCBat
≤
0.2 Controller for
load shedding
SCB
SoCBat
AND
SoCSC
≥
≥
0.8
1
SoCBat
AND
If 0.2 ≤ SoCBat ≤ 0.8
AND
SoCSC If 0 ≤ SoCSC ≤ 1
FIGURE 2 HESS control strategy
AC side inverter controller
FIGURE 3 show the inverter circuit and this is accountable to delivercommandtotheinverterformaintainingthefrequencyas
well as AC voltage in the limits at the load end. Inverter controller senses output voltages at the load end and then converts
these three phase components into two phase quantities (d-q). These signals of the AC voltage are equated to the two phase
quantities and the resultant difference between the actual and observed values is processed through the anotherPI controller
pair. This pair generates the signals for the inverter to maintain the voltage and frequency in the limits.
For maintaining the entire control scheme in synchronism PLL is utilized this makes the signals in tandem the operating
frequency is maintained.
VLa VLb VLc
abc to dq
transformation
id
*
Three-phase
PLL
VL_d
θ
-
+
-
+
VL_d
*
dq to abc
transformation
θ
PI
PI
iq
*
PWM
Control
signals
(S1-6)
a b c
VL_q
VL_q
*
FIGURE 3 Three phase inverter controller
III. Simulations and results
As discussed earlier the generation and consumption is not same and inconstant by nature that is why the enactment of the
system is examined considering changing inputs in order to mimic practical situation. The wind variations measured are
presented in FIGURE 4 (a). Firstly it is 8 m/sec the incremented at 10 m/sec on the time being 3 sec. There is again change in
the wind speed and it became 12 m/sec when time is 5 sec. Likewise, change in solar irradianceisalsomadeandin startingitis
800 W/m2 then increases to 1000 W/m2 at time being 2 sec and to 1200 W/m2 att=4sec,andsameisdepictedinFIGURE4(b).
FIGURE 4 (c) displays variations in load current that decreases to 3 A from 9 A when time is 6 sec.
VDC is varied at a great extend subjected to inconsistent operating circumstancesandshouldbepersistentto640Vthatistaken
as the reference value for this study. FIGURE 4 (d) presents the shape of VDC at various occasions considering change in other
scenarios like wind speed etc. The results presented in various figures verified that the controller can keep the VDC around the
prescribed value (± 5%) in transients as well as long term situations. Upholding the VDC unchangedaidstomaintain ACvoltage
at constant level irrespective of solar irradiance and wind speed the DC voltage and corresponding AC voltage is givenas[54]:
1
2 2
P N DCV k V− = (6)

Here, phase to neutral voltage is denoted by VP-N and modulation index by k.
If there are some variations in the load end as shown in FIGURE 4 (c) then inverter controller provides adequate governor to
counter these variations. By eaxmine FIGURE 4 (e), proposed controller can maintain thefrequencyalmostconstantandthere
is a little variation in frequency occurs at time 6 sec. because load is straightly linkedtoACside.Thisisachieved byutilizingthe
PLL circuit that keep the frequency on track during the entire operation. FIGURE 4 (f) and FIGURE 4 (g) are showing three-
phase instantaneous voltage and the phase (P-N) RMS voltage. Increased view of FIGURE 4 (g) now shown that displays no
substantial variation in AC voltage with the change in connected load.
FIGURE 4 Various waveforms in surplus power mode (a) Variation in the speed of wind (m/sec), (b) Variation in
the incident solar radiations (W/m2), (c) variations in the current at the load side, (d) variations in the voltage at
the PCC, (e) variations in the frequency, (f) variations in the AC voltage at the load, (g) Instantaneous load voltage
The output of the PV system and WECS depends on the change in solar irradianceand windspeedasvisibleinError!Reference
source not found. (g). The extra power from the hybrid system is made use of in chargingofthebothESS whereslow transients
are transferred to the battery and fast transients are transferred to the supercapacitor. The variations in the both ESSs is
displayed in Error! Reference source not found. (b) which is in accordance with the variable wind speed and solar irradiance.
Rapidly moving component of power mismatch is transferred to SCESS and it is shown in Error! Reference source not found.
(e). At the time variation in solar power occurs when time reaches to 2 sec (Error! Reference source not found. (b)),
correspondingly the current generated by the PV system also changes and by the output power of the PV system also changes
and both the variations are displayed in Error! Reference source notfound.(a)andError!Referencesource notfound.(g).Asof
insignificant inertia of PV system, sharp increase in its current occurswithsolarirradiancechanges whichsubsequentlyeffects
in instantaneous rise in generated power of PV system. SCESS compensates this sudden changeinthePVsystemoutputpower
afterwards slowly taken over by battery which helps in protection of battery from suddenchargingandsamething isshownin
Error! Reference source not found. (e), Error! Reference source not found. (b), and Error! Reference source not found. (g).
When time reaches to 3 sec, with speed of the wind changes that also changes the output current of the WECS as shown in
Error! Reference source not found. (a) and Error! Reference source not found. (d)). This helps in increment of WECS power
(Error! Reference source not found. (g)). Due to this more surplus current is available for the battery as shown in Error!
Reference source not found. (b)) also the power (Error! Reference source not found. (g). Anothertime4sec,incrementinsolar
irradiance (Error! Reference source not found.1(b)),causestoshootupthePVsystemcurrentandcorrespondingpowerwhich
provides more power to battery for its charging. When battery charging level reaches to it upper value which is set at 80% at
time being 4.6 sec (Error! Reference source not found. (c)) battery will not take more power for its charging and power excess
available is moved to dump load as displayed in Error! Reference source not found. (g). At time t=5 sec, again wind speed is
increased which causes WECS output power that leads to more power to dump load (Error! Reference source not found. (g))
because battery cannot take more power because it is at its highest state of charge. After this, when connected load is reduced
at time 6 sec, extra power thus presented goes to dump (Error! Reference sourcenotfound.(g)).InthisentireperiodtheSoCof
supercapacitor is well under the range and when there any change in operating condition occurs SCESS goes back to charging
mode after absorbing the change in operating condition. As shown in Error! Reference source not found. (f).

Error! Reference source not found. Waveforms in surplus power mode (a) output current of PV system (A), (b)
variation in current for BESS (A), (c) variations in SoCBat (%), (d) variations in output current of WECS (A), (e)
variations in output current of SCESS (A), (f) variations in SoCSC (%) and (g) various power waveforms (kW)
Deficit power mode (DPM)
For examining efficacy of control strategy suggested for this
work in under-generation situation the system is simulated
in DPM. In DPM, shortage in power is shared by battery and
supercapacitor accordingtotheircharacteristics.Though the
capacity of both ESSs is carefully chosen taking in to account
the SoCBat cannot be below the 20% underanysituation with
power from PV and WECS is not available. For these types of
situation the non-critical load is shedded off when SoCBat is
less than the minimum value. For mimicking this situation,
SoCBat is purposely considered near to 20% and battery will
make its connection off from the system when its state of
charge reaches to 20%.
IV. Conclusions
In this paper, a control schemeisproposedandimplemented
for the grid-isolated hybrid renewable energy system
incorporating battery and supercapacitor. The control
scheme is tested in over generation and under generation
situations and worked according to expectations. By testing
the system for under and over generation scenarios it is
concluded that the system behaved as per the expectation
and could able to maintain the frequency, difference in
generation and demand, DC link voltage within the safe
range when subjected to changing situations. Furthermore,
gradual charging & discharging of BESS is attained withhelp
of SCESS and giving it the fast moving transients. Along with
that the controller could maintained the SoC of BESS in
limits. Apart form that the three phase voltage and its
frequency didn’t violates the prescribed range.
V. REFERENCES
[1] B. Li, R. Roche, and A. Miraoui, “Microgrid sizing with
combined evolutionary algorithm and MILP unit
commitment,” Appl. Energy, vol.188,pp.547–562,Feb.
2017.
[2] L. Barelli et al., “Dynamic Analysis of a Hybrid Energy
Storage System (H-ESS) Coupled to a Photovoltaic(PV)
Plant,” Energies, vol. 11, no. 2, p. 396, Feb. 2018.
[3] M.-E. Choi, S.-W. Kim, and S.-W. Seo, “Energy
Management Optimizationina Battery/Supercapacitor
Hybrid Energy Storage System,” IEEE Trans. Smart
Grid, vol. 3, no. 1, pp. 463–472, Mar. 2012.
[4] M. Aneke and M. Wang, “Energy storage technologies
and real life applications – A state of the art review,”
Appl. Energy, vol. 179, pp. 350–377, Oct. 2016.
[5] P. D. Lund, J. Lindgren, J. Mikkola, and J. Salpakari,
“Review of energy system flexibility measures to
enable high levels of variable renewable electricity,”
Renew. Sustain. Energy Rev., vol. 45, pp. 785–807, May
2015.
[6] J. Lei and Q. Gong, “Optimal allocation of a hybrid
energy storage system considering its dynamic
operation characteristics for wind power applications
in active distribution networks,” Int. J. Energy Res.,vol.
42, no. 13, pp. 4184–4196, Oct. 2018.
[7] O. Krishan and S. Suhag, “An updated review of energy
storage systems: Classification and applications in

distributed generation power systems incorporating
renewable energy resources,” Int. J. Energy Res., no.
October, pp. 1–40, Nov. 2018.
[8] P. Nikolaidis and A. Poullikkas, “A comparative review
of electrical energy storage systems for better
sustainability,” J. Power Technol., vol. 97, no.
November, pp. 220–245, 2017.
[9] M. S. Guney and Y. Tepe, “Classificationandassessment
of energy storage systems,” Renew. Sustain. Energy
Rev., vol. 75, no. November 2016, pp. 1187–1197,
2017.
[10] D. O. Akinyele and R. K. Rayudu, “Review of energy
storage technologies for sustainable powernetworks,”
Sustain. Energy Technol. Assessments, vol. 8, pp. 74–
91, Dec. 2014.
[11] E. M. G. Rodrigues, R. Godina, S. F. Santos, A. W.
Bizuayehu, J. Contreras, and J. P. S. Catalão, “Energy
storage systems supporting increased penetration of
renewables in islanded systems,” Energy, vol. 75, pp.
265–280, Oct. 2014.
[12] B. Hredzak, V. G. Agelidis, and G. Demetriades,
“Application of explicit model predictive control to a
hybrid battery-ultracapacitor power source,” J. Power
Sources, vol. 277, pp. 84–94, Mar. 2015.
[13] N. Mendis, K. M. Muttaqi, and S. Perera, “Management
of Battery-Supercapacitor Hybrid Energy Storage and
Synchronous Condenser for Isolated Operation of
PMSG Based Variable-Speed Wind Turbine Generating
Systems,” IEEE Trans. Smart Grid, vol. 5, no. 2,pp.944–
953, Mar. 2014.
[14] A. M. Gee, F. V. P. Robinson, and R. W. Dunn, “Analysis
of Battery Lifetime Extension in a Small-Scale Wind-
Energy System Using Supercapacitors,” IEEE Trans.
Energy Convers., vol. 28, no. 1, pp. 24–33, Mar. 2013.
[15] X. Feng, H. B. Gooi, and S. X. Chen, “Hybrid Energy
Storage With Multimode Fuzzy Power Allocator for PV
Systems,” IEEE Trans. Sustain. Energy, vol. 5, no. 2, pp.
389–397, Apr. 2014.
[16] Z. Cabrane, M. Ouassaid, and M. Maaroufi, “Battery and
supercapacitor for photovoltaicenergystorage:a fuzzy
logic management,” IET Renew. Power Gener., vol. 11,
no. 8, pp. 1157–1165, Jun. 2017.
[17] X. Wang, D. Yu, S. Le Blond, Z. Zhao, and P. Wilson, “A
novel controller of a battery-supercapacitor hybrid
energy storage system for domestic applications,”
Energy Build., vol. 141, pp. 167–174, Apr. 2017.
[18] A. M. O. Haruni, M. Negnevitsky, M. E. Haque, and A.
Gargoom, “A Novel Operation and Control Strategy for
a Standalone Hybrid Renewable Power System,” IEEE
Trans. Sustain. Energy, vol. 4, no. 2, pp. 402–413, Apr.
2013.

Control and Power Management in HRES System

More Related Content

What's hot

Similar to Control and Power Management in HRES System

More from ijtsrd

Recently uploaded

Control and Power Management in HRES System