Advanced LIGO T030118-01-D

Guide for Specification of Imperial Bolts, Threads and Hole Fits in Advanced LIGO Parts

Metric Equivalents to Imperial Bolts and Through Hole Specification

This document serves as a reference guide when adding clearance holes on parts drawn up in
Solidworks or other associated CAD packages.

During the development of the Mode Cleaner Controls Prototype the close-fit hole specification
and drill sizes, shown in the table below, were used. Where tight positional tolerances were
required, a hole-to-hole tolerance of +/-0.001inch was commonly specified. A good example of
this can be seen in the upper blade drawings (D020205).
For further information on coaxial and concentric tolerancing of holes, refer to ASME Y14.5M-
1994 or equivalent.

Where possible, to avoid unneeded additional cost of tight tolerance machining, the Free or
Normal-fit specification (again, shown in the table below) should be used. In this situation a hole-
to hole tolerance of +/-0.005 will be adequate.

Whilst working in metric units, typing 'in' after a dimension will trigger SolidWorks to
automatically calculate the metric equivalent of an inch dimension. e.g. for a close-fit hole
øA
specification for a #4-40 bolt, typing '0.1285in' will give you a metric dimension of '3.2639mm'
øB
NOTE ** - In compiling this document, the term 'close-fit' has been found to be used very loosely
with some references implying close-fits greater than those shown.

Approx. Actual Actual Close-fit Free-fit Normal-fit

Alternative Hole Specification (i.e. available Drill sizes between
Imperial Metric Diameter Diameter hole ** Drill hole spec. Drill hole spec. Drill
Close and Free Fit) [inches / Drill Size]
Size Equivalent [inches] [mm] spec. [in] Sizeble Drill sizes) between Close and Normal Fit (inches) [in] Size [in] Size
ØA ØB
#2-56 M2 0.086 2.1844 0.0890 43 0.0935 42 0.0938 3/32 - - - - 0.0960 41 0.1065 36
#4-40 M3 0.112 2.8448 0.1160 32 0.1200 31 0.1250 1/8 - - - - 0.1285 30 0.136 29
#6-32 M3.5 0.125 3.175 0.1285 30 0.1360 29 0.1406 9/64 0.1440 27 0.1470 26 0.1495 25 0.1695 18
#8-32 M4 0.164 4.1656 0.1695 18 0.1719 11/64 0.1730 17 - - - - 0.1770 16 0.1935 10
#10-24 M5 0.19 4.826 0.1935 10 0.1960 9 0.1990 8 - - - - 0.2010 7 0.221 2
#1/4-20 M6 0.25 6.35 0.2570 F 0.2610 G 0.2656 17/64 - - - - 0.2660 H 0.2812 9/32
#5/16-18 M8 0.3125 7.9375 0.3230 P 0.3281 21/64 - - - - - - 0.3320 Q 0.3438 11/32
#3/8-16 M10 0.375 9.525 0.3860 W 0.3906 25/64 - - - - - - 0.3970 X 0.4062 13/32
#1/2-13 M12 0.5 12.7 0.5156 33/64 - - - - - - - - 0.5312 17/32 0.5312 17/32

Additional Information for Countersink Holes, etc.

Max. Bolt
Max. Bolt Head Typical D
øE

Imperial Head Dia. Height C'Bore D

Size (in.) (in.) Dia. (in.)
ØC D ØE
#2-56 0.140 0.086 0.188
øC

#4-40 0.183 0.112 0.219

#6-32 0.226 0.138 0.281
#8-32 0.270 0.164 0.313
#10-24 0.313 0.190 0.375
#1/4-20 0.375 0.250 0.438
#5/16-18 0.409 0.313 0.531
#3/8-16 0.562 0.375 0.625
#1/2-13 0.750 0.500 0.813

INCH/METRIC TAP DRILL SIZES & DECIMAL EQUIVALENTS

REFERENCES:
1 Starrett Precision Tools; [Link];
Inch/Metric Tap Drill Sizes & Decimal
Equivalents ; Free reference Card (as shown in
picture, left); Catalogue item number 1317 . Note
that all above decimal hole diameters have
corresponding fractions or drill sizes.
2 Tapping and Clearance Hole Information,
[Link]/~jwodin/[Link]

3 Unbrako Engineering Guide (Inch & Metric),

Through Hole Preperation ;
[Link]/unbrako/htm/[Link]

4 ASME Y14.5M-1994 Dimensioning and

Tolerancing,

Michael Perreur-Lloyd, 24th February 2004