3.
38
SECTION THREE
FIGURE 3.28 Shears moments, and deformations
for midspan load on a simple beam.
FIGURE 3.29 Diagrams for moment applied at one
end of a simple beam.
Fy R1 R2 wL 0
R1
wL
2
With the origin taken at the left end of the span, the shear at any point can be obtained from
Eq. (3.80e) by integration: V w dx wx C1, where C1 is a constant. When x
0, V R1 wL / 2, and when x L, V R2 wL / 2. For these conditions to be satisfied,
C1 wL/ 2. Hence the equation for shear is V(x) wx wL/ 2 (Fig. 3.31b).
The bending moment at any point is, by Eq. (3.80d ), M(x) V dx (wx wL/ 2)
dx wx 2 / 2 wLx / 2 C2, where C2 is a constant. In this case, when x 0, M 0.
Hence C2 0, and the equation for bending moment is M(x) 12w (x2 Lx), as shown
in Fig. 3.31c. The maximum bending moment occurs at midspan, where x L / 2, and equals
wL2 / 8.
From Eq. (3.80c), the slope of the deflected member at any point along the span is
(x)
w
M(x)
dx
(x
EI
2EI
Lx) dx
w
x 2 Lx 2
C3
2EI
3
2
where C3 is a constant. When x L / 2, 0. Hence C3 wL3 / 24EI, and the equation
for slope is
(x)
(See Fig. 3.31d.)
w
(4x 3 6Lx 2 L3)
24EI
FIGURE 3.30 Diagrams for moments applied at
both ends of a simple beam.
FIGURE 3.31 Shears, moments, and deformations
for uniformly loaded simple beam.
FIGURE 3.32 Simple beam with concentrated load
at the third points.
FIGURE 3.33 Diagrams for simple beam loaded at
quarter points.
3.40
SECTION THREE
FIGURE 3.34 Diagrams for concentrated load on a
simple beam.
FIGURE 3.35 Symmetrical triangular load on a
simple beam.
FIGURE 3.36 Concentrated load on a beam overhang.
FIGURE 3.37 Uniformly loaded beam with overhang.
GENERAL STRUCTURAL THEORY
3.41
FIGURE 3.38 Shears, moments, and deformations
for moment at one end of a cantilever.
FIGURE 3.39 Diagrams for concentrated load on a
cantilever.
FIGURE 3.40 Shears, moments, and deformations
for uniformly loaded cantilever.
FIGURE 3.41 Triangular load on cantilever with
maximum at support
3.42
SECTION THREE
FIGURE 3.42 Uniform load on beam with one end
fixed, one end on rollers.
FIGURE 3.43 Triangular load on beam with one
end fixed, one end on rollers.
The deflected-shape curve at any point is, by Eq. (3.80b),
(x)
w
24EI
(4x
6Lx 2 L3) dx
wx4 / 24EI wLx 3 / 12EI wL3x / 24EI C4
where C4 is a constant. In this case, when x 0, 0. Hence C4 0, and the equation
for deflected shape is
(x)
w
(x 4 2Lx 3 L3x)
24EI
as shown in Fig. 3.31e. The maximum deflection occurs at midspan, where x L / 2, and
equals 5wL4 / 384EI.
For concentrated loads, the equations for shear and bending moment are derived in the
region between the concentrated loads, where continuity of these diagrams exists. Consider
the simply supported beam subjected to a concentrated load at midspan (Fig. 3.28a). From
equilibrium equations, the reactions R1 and R2 equal P / 2. With the origin taken at the left
end of the span, w(x) 0 when x L / 2. Integration of Eq. (3.80e) gives V(x) C3, a
constant, for x 0 to L / 2, and V(x) C4, another constant, for x L / 2 to L. Since V
R1 P / 2 at x 0, C3 P / 2. Since V R2 P / 2 at x L, C4 P / 2. Thus, for
0 x L / 2, V P / 2, and for L / 2 x L, V P / 2 (Fig. 3.28b). Similarly, equations
GENERAL STRUCTURAL THEORY
FIGURE 3.44 Moment applied at one end of a
beam with a fixed end.
3.43
FIGURE 3.45 Load at midspan of beam with one
fixed end, one end on rollers.
for bending moment, slope, and deflection can be expressed from x 0 to L / 2 and again
for x L / 2 to L, as shown in Figs. 3.28c, 3.28d, and 3.28e, respectively.
In practice, it is usually not convenient to derive equations for shear and bending-moment
diagrams for a particular loading. It is generally more convenient to use equations of equilibrium to plot the shears, moments, and deflections at critical points along the span. For
example, the internal forces at the quarter span of the uniformly loaded beam in Fig. 3.31
may be determined from the free-body diagram in Fig. 3.50. From equilibrium conditions
for moments about the right end,
M M wL4 L8 wL2 L4 0
M
3wL2
32
(3.81a)
(3.81b)
Also, the sum of the vertical forces must equal zero:
F wL2 wL4 V 0
y
wL
4
Several important concepts are demonstrated in the preceding examples:
(3.82a)
(3.82b)
3.44
FIGURE 3.46 Shears, moments, and deformations
for uniformly loaded fixed-end beam.
FIGURE 3.47 Diagrams for triangular load on a
fixed-end beam.
FIGURE 3.48 Shears, moments, and deformations
for load at midspan of a fixed-end beam.
FIGURE 3.49 Diagrams for concentrated load on a
fixed-end beam.
