Scribd
Upload
200 views1 page

Design Data: Design of Floor Slab

This document provides the design calculations for a two-way floor slab with short and long spans of 3.813m and 4.118m respectively. It calculates the factored design load, required reinforcement, shear strength, and deflection to determine the slab design is adequate with 8mm bars provided at 150mm centers for both spans. All checks for moment capacity, deflection, and shear are shown to meet code requirements.

Uploaded by

Drafters Engineering
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
200 views1 page

Design Data: Design of Floor Slab

This document provides the design calculations for a two-way floor slab with short and long spans of 3.813m and 4.118m respectively. It calculates the factored design load, required reinforcement, shear strength, and deflection to determine the slab design is adequate with 8mm bars provided at 150mm centers for both spans. All checks for moment capacity, deflection, and shear are shown to meet code requirements.

Uploaded by

Drafters Engineering
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd

Design of Floor Slab

Design Data
fck = 20 N/mm2
fy = 415 N/mm2
Dimensions of the slab (c/c distance betn supports),
Length of short span, lx = 3.962 m
Length of long span, ly = 4.267 m
Width of the supporting beam, = 230 mm
Clear cover to main reinforcement = 15 mm
Assume dia. of reinforcement steel = 8 mm

Calculations
Assume the thickness of slab as 100 mm ;
Effective depth, deff = 81 mm
Effective span, lx = 3.962 m (or) 3.813 m whichever is less; = 3.813 m
ly = 4.267 m (or) 4.118 m whichever is less; = 4.118 m
(ly / lx ) = 1.08 < 2 ; Here, (ly / lx ) is less than 2
Hence design the slab as two way slab

Load Calculations
Dead Load of slab = 0.1 x 25 = 2.50 KN/m2
Finishes load on slab = 1.00 KN/m2
Total Dead load acting on the slab = 3.50 KN/m2
Live Load on slab = 2.0 KN/m2
Factored Design Load, W = 8.25 KN/m2

Support Condition (Type of panel according to support condition)


Two Adjacent Edges Discontinuous For this support condition,
Short span coefficient for (ly / lx ) = 1.08, Long span coefficient,
For negative moment, ax = 0.0518 For negative moment, ay = 0.047
For positive moment, ax = 0.0390 For positive moment, ay = 0.035

Moment Calculation
Max. BM per unit width, Mx = ax w l x 2 & My = ay w l x 2

Mu Mu / bd2 pt Ast, req Ast , min = (0.12/100) bD = 120 mm2


KNm N/mm2 % mm2
For Short Span,
Reinforcement details
At mid span, 4.68 0.71 0.2055 166
At supports, 6.21 0.95 0.2795 226 Provide 8 @ 150 mm c/c at midspan &
For Long span, supports for short span (Ast pro. = 335 mm2 )
At mid span, 4.20 0.79 0.2299 186 Provide 8 @ 150 mm c/c at midspan &
At supports, 5.64 1.06 0.3143 255 supports for long span (Ast pro. = 335 mm2 )

Check for Deflection


Percentage of tension reinforcement = 0.34 %
fs = 0.58 fy (Ast req / Ast pro) = 119
Refer Fig. 4 of IS 456,
Modification factor = 2
( l/ d) max = ( l/ d) basic x kt x kc = 52
( l/ d)provided = 47
< ( l/ d) max (i.e. = 52) OK
Hence safe in deflection.

Check for shear


Shear force per m strip (W*lx/2), V = 15.729 KN/m
Shear stress , (V/bd), τv = 0.160 N/mm2
Pt = 0.34%
Design Shear Strength of Concrete
τc = 0.360 N/mm2 Refer Table 19, IS 456
> τv (i.e. = 0.16) OK
Since τc > τv, so safe in shear.

You might also like