Scribd
Upload
209 views2 pages

2 RD100 PDF

This document provides a parts list and specifications for upgrading a Dana 30 or Dana 27 rear differential to an ARB limited slip differential model RD100. The parts list includes 19 main components needed for the upgrade along with additional notes. Specifications provided include axle spline size, supported gear ratios, ring gear dimensions, bolt patterns, torque specifications, and backlash range.

Uploaded by

Christian Perez
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
209 views2 pages

2 RD100 PDF

This document provides a parts list and specifications for upgrading a Dana 30 or Dana 27 rear differential to an ARB limited slip differential model RD100. The parts list includes 19 main components needed for the upgrade along with additional notes. Specifications provided include axle spline size, supported gear ratios, ring gear dimensions, bolt patterns, torque specifications, and backlash range.

Uploaded by

Christian Perez
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd

RD100 Dana 30,27 SPL,3.

73 & UP
PARTS LIST
ITEM # QTY DESCRIPTION PART # NOTES
1 1 SEAL HOUSING O-RINGS (PK OF 2) 160235SP 1
2 1 SEAL HOUSING KIT 081801SP
3 2 SHIM KIT SHK003
* 2 MASTER SHIM 150325
4 1 BONDED SEAL 160701SP
5 1 CLUTCH GEAR & WAVESPRING KIT 050903SP
6 1 SPIDER BLOCK 070503SP
7 1 LONG CROSS SHAFT 061302SP
8 1 SIDE GEAR SEE NOTE 3
9 1 COUNTERSUNK SCREW (PK OF 2) 200213SP
10 1 RETAINING PIN SET (PK OF 4) 120601SP
11 2 TAPERED ROLLER BEARING 160109 2
12 1 FLANGE CAP KIT 028502SP
13 1 WAVESPRING 150702SP
14 1 SPLINED SIDE GEAR SEE NOTE 3
15 2 SHORT CROSS SHAFT 061402SP
16 4 PINION GEAR SEE NOTE 3
17 4 PINION THRUST WASHER SEE NOTE 4
18 2 SIDE GEAR THRUST WASHER SEE NOTE 4
19 1 DIFFERENTIAL CASE 013102SP
* 1 BULKHEAD FITTING KIT (BANJO TYPE) 170114 5
* 1 AIR LINE (6mm DIA X 6m LONG) 170314 5
* 1 SOLENOID VALVE (12V) 180103SP
* 1 SWITCH 180209SP
* 1 SWITCH COVER (FRONT) 180210SP
* 1 CABLE TIE (PK OF 25) 180305
* 1 OPERATING & SERVICE MANUAL 210200
* 1 INSTALLATION GUIDE 2102100

* Not illustrated in exploded view

NOTES
1 For replacement O-rings use only BS133 Viton 75.
2 For replacement bearing use Timken part # LM102949 / LM102910.
3 Available only as complete 6 gear set # 728J011
4 Available only as complete thrust washer kit #730J01
5 All diffs produced before serial # 17070001 came with 5mm air connection system. For information contact ARB.
- For ratios of 3.54:1 and down refer to RD101 (Section 2.101).
- Bearing cap torque does not apply to aluminium housings. Refer to vehicle’s
service manual for correct torque value.

1 of 2
Updated 15/05/2018
RD100 Dana 30,27 SPL,3.73 & UP

EXPLODED DIAGRAM

SPECIFICATIONS
Axle Spline 27 tooth, Ø29.5mm [1.16“]
Ratio Supported 3.73:1 & up
Ring Gear ID 114.3mm [4.50”]
Ring Gear OD 183mm [7.2”]
Ring Gear Bolts 10 bolts on Ø133mm [5.25”]
Ring Gear Torque 75Nm [55 ft-lb]
Backlash 0.15-0.25mm [0.006-0.010”]
Bearing Cap Torque 81Nm [60 ft-lb] (see note 4)

ARB Corporation Ltd ▪ 42-44 Garden St Kilsyth VIC 3137 Australia


ARB 4X4 Accessories USA ▪ 720 SW 34th St Renton WA 98057 USA
Australia & International Customer Service ▪ +61 3 9761 6622
North America Customer Service ▪ Toll Free 866 293 9078
www.arb.com.au (AUS & Int) www.arbusa.com (N. America)
2 of 2
Updated 15/05/2018

You might also like