Parameter Settings Report (Program) 18/10/2020 [Link] p. m.

Program (Drive Selected / Connected):

Drive Type / Model: A1000 CIMR-A*2*0021***
Software: 1022

Project:
User:

Information Last Updated: 18/10/2020 [Link] p. m.

Default
Parameter Value Information Setting

A1-01 Access level 2 Advanced Level Access 2

0 V/f control 2
A1-04 Enter password 0 0
1 Water supply pump 0
A1-07 DWEZ Function Selection 0 Disabled 0

C1-01 Acceleration time 1 b1-01

A2-02 User parameter 2 b1-02 Operation method selection b1-02
A2-03 User parameter 3 b1-04 Reverse operation b1-04
A2-04 User parameter 4 C1-01 Acceleration time 1 C1-01
A2-05 User parameter 5 C1-02 Deceleration time 1 C1-02
A2-06 User parameter 6 E1-03 V/F pattern selection E1-03
A2-07 User parameter 7 E1-07 Mid output frequency E1-07
A2-08 User parameter 8 E1-08 Mid output frequency voltage E1-08
A2-09 User parameter 9 E2-01 Motor rated current E2-01
A2-10 User parameter 10 H1-05 Terminal S5 function selection H1-05
A2-11 User parameter 11 H1-06 Terminal S6 function selection H1-06
A2-12 User parameter 12 H1-07 Terminal S7 function selection H1-07
A2-13 User parameter 13 L5-01 Number of auto restart attempts L5-01
A2-14 User parameter 14 ----- -----
A2-15 User parameter 15 ----- -----
A2-16 User parameter 16 ----- -----
E1-05 Max. voltage -----
L8-07 Phase loss output selection -----
C4-01 Torque compensation gain -----
A2-20 User parameter 20 ----- -----
A2-21 User parameter 21 ----- -----
A2-22 User parameter 22 ----- -----
A2-23 User parameter 23 ----- -----
A2-24 User parameter 24 ----- -----
A2-25 User parameter 25 ----- -----
A2-26 User parameter 26 ----- -----
A2-27 User parameter 27 ----- -----

DriveWizard Industrial for Windows (C) by Yaskawa America, Inc. 1/14

 Default
Parameter Value Information Setting
A2-28 User parameter 28 ----- -----
A2-29 User parameter 29 ----- -----
A2-30 User parameter 30 ----- -----
A2-31 User parameter 31 ----- -----
A2-32 User parameter 32 ----- -----
A2-33 User parameter Automatic registration 1 Automatic registration is available (A2-17~A2-32 are stored 1
Function automatically)

b1-01 Reference selection 1 Control circuit terminal 1

b1-02 Operation method selection 1 Control circuit terminal 1
b1-03 Stopping method 0 Deceleration to stop 0
1 Reverse disabled 0
b1-06 Digital Input Scan Selection 1 2 Scans 1
b1-07 Local/remote run selection 0 Cycle External Run - If the run command is closed when 0
switching from LOCAL mode or alternative reference to
b1-08 Run command at programming 0 Cannot
REMOTE operate
mode, the drive will not run. 0
b1-14 Phase Turn Selection 0 Normal 0
b1-15 Reference Selection in Local case 0 Digital operator 0
b1-16 Operation method selection in Local case 0 Digital operator 0
1 Permission 0

b2-01 DC injection start frequency 0.5 Hz 0.5 Hz

b2-02 DC injection current 50 % 50 %
b2-03 DC injection time at start 0.00 sec 0.00 sec
b2-04 DC injection time at stop 0.50 sec 0.50 sec

b3-01 Speed search at start 0 Disabled 0

b3-02 Speed search current 120 % 120 %
b3-03 Speed search deceleration time 2.0 sec 2.0 sec
b3-04 Speed search V/F 100 % 100 %
b3-05 Search wait time 0.2 sec 0.2 sec
b3-06 Output current 0.5 0.5
b3-08 Current Control Gain during Speed Search 0.50 0.50
(Speed Estimation Type)
b3-10 Speed Search Detection Compensation Gain 1.05 1.05
b3-14 Bidirectional search selection 1 Enabled 1
b3-17 Retry current level 150 % 150 %
b3-18 Retry detection time 0.10 sec 0.10 sec
b3-19 Retry count 3 3
b3-24 Speed search method selection 0 Current detection type 0
b3-25 Speed search retry interval time 0.5 sec 0.5 sec
b3-27 Start Speed Search select 0 Run command given 0
b3-33 Speed Search select at start during UV 0 Disabled 0

b4-01 Delay-ON timer 0.0 sec 0.0 sec

b4-02 Delay-OFF timer 0.0 sec 0.0 sec
b4-03 H2-01 On-Delay Time 0 ms 0 ms
b4-04 H2-01 Off-Delay Time 0 ms 0 ms
b4-05 H2-02 On-Delay Time 0 ms 0 ms
b4-06 H2-02 Off-Delay Time 0 ms 0 ms
b4-07 H2-03 On-Delay Time 0 ms 0 ms
b4-08 H2-03 Off-Delay Time 0 ms 0 ms

b5-01 PID control mode selection 0 Disabled 0

b5-02 PID P gain 1.00 1.00
b5-03 PID I time 1.0 sec 1.0 sec

DriveWizard Industrial for Windows (C) by Yaskawa America, Inc. 2/14

 Default
Parameter Value Information Setting
b5-04 PID I limit 100.0 % 100.0 %
b5-05 PID D time 0.00 sec 0.00 sec
b5-06 PID limit 100.0 % 100.0 %
b5-07 PID offset adjustment 0.0 % 0.0 %
b5-08 PID primary delay time constant 0.00 sec 0.00 sec
b5-09 Output level selection 0 PID output is forward. 0
b5-10 PID output gain 1.00 1.00
b5-11 PID output reverse selection 0 0 limit when PID output is negative 0
b5-12 Feedback loss detection selection 0 Disabled. No detection PID feedback loss. 0
b5-13 Feedback loss detection level 0% 0%
b5-14 Feedback loss detection time 1.0 sec 1.0 sec
b5-15 PID sleep level 0.0 Hz 0.0 Hz
b5-16 PID sleep time 0.0 sec 0.0 sec
b5-17 Accel/Decel time for PID reference 0.0 sec 0.0 sec
b5-18 PID Setpoint Selection 0 Disable 0
b5-19 PID Setpoint Value 0.00 % 0.00 %
b5-20 PID Setpoint Scaling 1 0.01% units 1
b5-34 PID Output Lower Limit 0.0 % 0.0 %
b5-35 PID Input Limit 1000.0 % 1000.0 %
b5-36 PID Feedback High Detection Level 100 % 100 %
b5-37 PID Feedback High Detection Time 1.0 sec 1.0 sec
b5-40 PID Fref monitor Selection 0 Fref Monitor with PID 0
b5-47 PID Output Reverse Selection 1 Reverses when PID output is negative. 1

b6-01 Dwell frequency at start 0.0 Hz 0.0 Hz

b6-02 Dwell time at start 0.0 sec 0.0 sec
b6-03 Dwell frequency at stop 0.0 Hz 0.0 Hz
b6-04 Dwell time at stop 0.0 sec 0.0 sec

b8-01 Energy-saving mode selection 0 Disabled 0

b8-04 Energy-saving coefficient 94.8 94.8
b8-05 kW filter time 20 ms 20 ms
b8-06 Search V limit 0% 0%

20.0 sec 10.0 sec

1.0 sec 10.0 sec
C1-03 Acceleration time 2 10.0 sec 10.0 sec
C1-04 Deceleration time 2 10.0 sec 10.0 sec
C1-05 Acceleration time 3 for motor2 10.0 sec 10.0 sec
C1-06 Deceleration time 3 for motor2 10.0 sec 10.0 sec
C1-07 Acceleration time 4 for motor2 10.0 sec 10.0 sec
C1-08 Deceleration time 4 for motor2 10.0 sec 10.0 sec
C1-09 Emergency stop time 10.0 sec 10.0 sec
C1-10 Accel/Decel time setting unit 1 0.1-second units 1
C1-11 Accel/Decel switching frequency 0.0 Hz 0.0 Hz

C2-01 S-curve acceleration at start 0.20 sec 0.20 sec

C2-02 S-curve acceleration at end 0.20 sec 0.20 sec
C2-03 S-curve deceleration at start 0.20 sec 0.20 sec
C2-04 S-curve deceleration at end 0.00 sec 0.00 sec

C3-01 Slip compensation gain 0.0 0.0

C3-02 Slip compensation time 2000 ms 2000 ms

DriveWizard Industrial for Windows (C) by Yaskawa America, Inc. 3/14

 Default
Parameter Value Information Setting
C3-03 Slip compensation limit 200 % 200 %
C3-04 Slip compensation regeneration 0 Slip compensation is disabled during regeneration. 0

1.20 1.00
C4-02 Torque compensation time 200 ms 200 ms

C6-01 Duty Cycle 1 ND(VT) 1

C6-02 Carrier frequency selection 07 Swing-PWM1 07

d1-01 Frequency reference 1 0.00 Hz 0.00 Hz

d1-02 Frequency reference 2 0.00 Hz 0.00 Hz
d1-03 Frequency reference 3 0.00 Hz 0.00 Hz
d1-04 Frequency reference 4 0.00 Hz 0.00 Hz
d1-05 Frequency reference 5 0.00 Hz 0.00 Hz
d1-06 Frequency reference 6 0.00 Hz 0.00 Hz
d1-07 Frequency reference 7 0.00 Hz 0.00 Hz
d1-08 Frequency reference 8 0.00 Hz 0.00 Hz
d1-09 Frequency reference 9 0.00 Hz 0.00 Hz
d1-10 Frequency reference 10 0.00 Hz 0.00 Hz
d1-11 Frequency reference 11 0.00 Hz 0.00 Hz
d1-12 Frequency reference 12 0.00 Hz 0.00 Hz
d1-13 Frequency reference 13 0.00 Hz 0.00 Hz
d1-14 Frequency reference 14 0.00 Hz 0.00 Hz
d1-15 Frequency reference 15 0.00 Hz 0.00 Hz
d1-16 Frequency reference 16 0.00 Hz 0.00 Hz
d1-17 Jog frequency reference 6.00 Hz 6.00 Hz

d2-01 Frequency reference upper limit 100.0 % 100.0 %

d2-02 Frequency reference lower limit 0.0 % 0.0 %
d2-03 Master speed reference lower limit 0.0 % 0.0 %

d3-01 Jump frequency 1 0.0 Hz 0.0 Hz

d3-02 Jump frequency 2 0.0 Hz 0.0 Hz
d3-03 Jump frequency 3 0.0 Hz 0.0 Hz
d3-04 Jump frequency width 1.0 Hz 1.0 Hz

d4-01 MOP reference memory 0 Disabled 0

d4-03 Frequency reference bias steps(up/down2) 0.00 Hz 0.00 Hz
d4-04 Accel/Decel rate selection(up/down2) 0 Bias value Accel/Decel at the rate of current selected 0
Accel/Decel time
d4-05 Bias mode selection(up/down2) 0 Hold bias value while both of UP/DOWN command are 0
ON/OFF
d4-06 Bias value(up/down2) 0.0 % 0.0 %
d4-07 Analog change limit 1.0 % 1.0 %
d4-08 Frequency Reference Bias Upper Limit 100.0 % 100.0 %
(up/down2)
d4-09 Frequency Reference Bias Lower Limit 0.0 % 0.0 %
(up/down2)
d4-10 Up/Down Frequency Reference Limit 0 The lower limit is determined by d2-02 or analog input 0
Selection (H3-02/10 = 0)

d6-01 Field weakening level 80 % 80 %

d6-02 Field frequency 0.0 Hz 0.0 Hz

d7-01 Offset frequency 1 0.0 % 0.0 %

d7-02 Offset frequency 2 0.0 % 0.0 %
d7-03 Offset frequency 3 0.0 % 0.0 %

DriveWizard Industrial for Windows (C) by Yaskawa America, Inc. 4/14

 Default
Parameter Value Information Setting
200 VAC 230 VAC
E1-03 V/F pattern selection 0F User-defined V/f pattern 0F
E1-04 Max. output frequency 60.0 Hz 60.0 Hz
200.0 VAC 230.0 VAC
E1-06 Base frequency 60.0 Hz 60.0 Hz
30.0 Hz 3.0 Hz
50.0 VAC 16.1 VAC
E1-09 Min. output frequency 1.5 Hz 1.5 Hz
E1-10 Min. output frequency voltage 8.1 VAC 8.1 VAC
E1-11 Mid output frequency 2 0.0 Hz 0.0 Hz
E1-12 Mid output frequency voltage 2 0.0 VAC 0.0 VAC
E1-13 Base voltage 0.0 VAC 0.0 VAC

23.60 A 19.60 A
E2-02 Motor rated slip 1.50 Hz 1.50 Hz
E2-03 Motor no-load current 5.10 A 5.10 A
E2-04 Number of motor poles 4 4
E2-05 Motor line-to-line resistance 0.399 Ohm 0.399 Ohm
E2-06 Motor leak inductance 18.2 % 18.2 %
E2-10 Torque compensation iron loss 172 W 172 W
E2-11 Motor rated output 5.50 kW 5.50 kW

F2-01 AI Option Input Mode Selection 0 3ch Individual Input 0

F2-02 AI Option Input Gain Setting 100.0 % 100.0 %
F2-03 AI Option Input Bias Setting 0.0 % 0.0 %

F3-01 DI Option Input Mode Selection 0 BCD 1% 0

F3-03 DI Option Bit Size Selection 2 16 bit 2

F4-01 Terminal V1 Monitor Setting 102 Output frequency 102

F4-02 Terminal V1 Monitor Gain Setting 100.0 % 100.0 %
F4-03 Terminal V2 Monitor Setting 103 Output current 103
F4-04 Terminal V2 Monitor Gain Setting 50.0 % 50.0 %
F4-05 Terminal V1 Monitor Bias Setting 0.0 % 0.0 %
F4-06 Terminal V2 Monitor Bias Setting 0.0 % 0.0 %
F4-07 AO1 Option Output Level Selection 0 0 to +10 V 0
F4-08 AO2 Option Output Level Selection 0 0 to +10 V 0

F5-01 DO Option ch1 Selection (DO08/DO02) 0000 Closed: There is a run command present or the drive is 0000
outputting voltage
F5-02 DO Option ch2 Selection (DO08/DO02) 0001 Closed: Output frequency is zero 0001
F5-03 DO Option ch3 Selection (DO08) 0002 Closed: Output frequency equals the speed reference (plus or 0002
minus the value set to L4-02)
F5-04 DO Option ch4 Selection (DO08) 0004 Closed: Output frequency is less than or equal to the value in 0004
L4-01 with hysteresis determined by L4-02.
F5-05 DO Option ch5 Selection (DO08) 0006 Closed: Drive Ready 0006
F5-06 DO Option ch6 Selection (DO08) 0037 During frequency output (ON: During frequency output) 0037
F5-07 DO Option ch7 Selection (DO08) 000F Not used 000F
F5-08 DO Option ch8 Selection (DO08) 000F Not used 000F
F5-09 DO Option (DO08) Output Mode Selection 0 8ch Individual Output 0

F6-01 Operation selection after communications 1 Coast to stop 1

error
F6-02 Selection of External Fault from 0 Always detect 0
Communication Option Board
F6-03 Stopping Method for External Fault from 1 Coast to Stop 1
Communication Option Board
F6-04 Trace Sampling from Communications 2.0 sec 2.0 sec
Option Board
F6-07 Fref Priority Selection 0 NetREF/ComREF are available. 0

DriveWizard Industrial for Windows (C) by Yaskawa America, Inc. 5/14

 Default
Parameter Value Information Setting
F6-08 Comm Parameter Initialize Selection 0 Comm Parameters are not initialized due to A1-02. 0
F6-10 Node Address 0 0
F6-11 Communication Speed 0 156 Kbps 0
F6-14 BUS Error Auto Reset 0 Disabled 0
F6-20 Station Address 21 21
F6-21 Frame length 0 32byte mode 0
F6-22 Link Speed 0 10MHz 0
F6-23 Mon E register 0000 0000
F6-24 Mon F register 0000 0000
F6-25 BUS Error Detection Mode Selection 1 Coast to Stop 1
F6-26 Number of BUS error detection 2 2
F6-30 Node Address 0 0
F6-31 Clear Mode Selection 0 Resets back to zero. 0
F6-32 ProfibusMap Selection 0 PPO Type 0
F6-35 Node Address 0 0
F6-36 CANopen Communication Speed 6 500 Kbps 6
F6-40 Node Address 0 0
F6-41 Communication Speed 1 Detect automatically 1
F6-45 Node Address 1 1
F6-46 Baud Rate 3 9600 bps 3
F6-47 Drive Transmit Wait Time 5 ms 5 ms
F6-48 BACnet Device Object Identifier 0 0000 0000
F6-49 BACnet Device Object Identifier 1 00 00
F6-50 MAC Address 64 64
F6-51 Baud Rate 4 Detect automatically 4
F6-52 PCA setting 21 21
F6-53 PPA setting 71 71
F6-54 Idle Mode Fault Detection 0 Stop 0
F6-56 Speed Scaling 0 0
F6-57 Current Scaling 0 0
F6-58 Torque Scaling 0 0
F6-59 Power Scaling 0 0
F6-60 Voltage Scaling 0 0
F6-61 Time Scaling 0 0
F6-62 Heart Beat 0 0
F6-64 Dynamic Output Assembly 109 Parameter 1 0000 0000
F6-65 Dynamic Output Assembly 109 Parameter 2 0000 0000
F6-66 Dynamic Output Assembly 109 Parameter 3 0000 0000
F6-67 Dynamic Output Assembly 109 Parameter 4 0000 0000
F6-68 Dynamic Input Assembly 159 Parameter 1 0000 0000
F6-69 Dynamic Input Assembly 159 Parameter 2 0000 0000
F6-70 Dynamic Input Assembly 159 Parameter 3 0000 0000
F6-71 Dynamic Input Assembly 159 Parameter 4 0000 0000
F6-72 Node Address 0 0
F6-75 P1-N2 Protocol Select 2 P1 2
F6-76 P1-N2 Comm Fault Enable 1 Enabled 1
F6-77 P1-N2 Comm Fault Time 2.0 sec 2.0 sec
F6-78 P1-N2 Node Address 1 1
F6-79 P1 Baud Rate Select 3 9600 bps 3

F7-01 IP Address1 192 192

F7-02 IP Address2 168 168
F7-03 IP Address3 1 1

DriveWizard Industrial for Windows (C) by Yaskawa America, Inc. 6/14

 Default
Parameter Value Information Setting
F7-04 IP Address4 20 20
F7-05 Subnet Mask1 255 255
F7-06 Subnet Mask2 255 255
F7-07 Subnet Mask3 255 255
F7-08 Subnet Mask4 0 0
F7-09 Gateway Address1 192 192
F7-10 Gateway Address2 168 168
F7-11 Gateway Address3 1 1
F7-12 Gateway Address4 1 1
F7-13 Address Startup Mode 2 DHCP 2
F7-14 Duplex Mode Setting 1 Auto Negotiate 1
F7-15 Speed Mode Setting 10 10 Mbps speed setting 10
F7-16 Timeout Value 0.0 sec 0.0 sec
F7-17 Speed Scaling 0 0
F7-18 Current Scaling 0 0
F7-19 Torque Scaling 0 0
F7-20 Power Scaling 0 0
F7-21 Voltage Scaling 0 0
F7-22 Time Scaling 0 0
F7-23 Dynamic Output Assembly 116 Parameter 1 0000 0000
F7-24 Dynamic Output Assembly 116 Parameter 2 0000 0000
F7-25 Dynamic Output Assembly 116 Parameter 3 0000 0000
F7-26 Dynamic Output Assembly 116 Parameter 4 0000 0000
F7-27 Dynamic Output Assembly 116 Parameter 5 0000 0000
F7-28 Dynamic Output Assembly 116 Parameter 6 0000 0000
F7-29 Dynamic Output Assembly 116 Parameter 7 0000 0000
F7-30 Dynamic Output Assembly 116 Parameter 8 0000 0000
F7-31 Dynamic Output Assembly 116 Parameter 9 0000 0000
F7-32 Dynamic Output Assembly 116 Parameter 10 0000 0000
F7-33 Dynamic Input Assembly 166 Parameter 1 0000 0000
F7-34 Dynamic Input Assembly 166 Parameter 2 0000 0000
F7-35 Dynamic Input Assembly 166 Parameter 3 0000 0000
F7-36 Dynamic Input Assembly 166 Parameter 4 0000 0000
F7-37 Dynamic Input Assembly 166 Parameter 5 0000 0000
F7-38 Dynamic Input Assembly 166 Parameter 6 0000 0000
F7-39 Dynamic Input Assembly 166 Parameter 7 0000 0000
F7-40 Dynamic Input Assembly 166 Parameter 8 0000 0000
F7-41 Dynamic Input Assembly 166 Parameter 9 0000 0000
F7-42 Dynamic Input Assembly 166 Parameter 10 0000 0000
F7-60 PZD1 Write 0000 0000
F7-61 PZD2 Write 0000 0000
F7-62 PZD3 Write 0000 0000
F7-63 PZD4 Write 0000 0000
F7-64 PZD5 Write 0000 0000
F7-65 PZD6 Write 0000 0000
F7-66 PZD7 Write 0000 0000
F7-67 PZD8 Write 0000 0000
F7-68 PZD9 Write 0000 0000
F7-69 PZD10 Write 0000 0000
F7-70 PZD1 Read 0000 0000
F7-71 PZD2 Read 0000 0000
F7-72 PZD3 Read 0000 0000
F7-73 PZD4 Read 0000 0000

DriveWizard Industrial for Windows (C) by Yaskawa America, Inc. 7/14

 Default
Parameter Value Information Setting
F7-74 PZD5 Read 0000 0000
F7-75 PZD6 Read 0000 0000
F7-76 PZD7 Read 0000 0000
F7-77 PZD8 Read 0000 0000
F7-78 PZD9 Read 0000 0000
F7-79 PZD10 Read 0000 0000

H1-01 Terminal S1 function selection 40 Forward Run Command 40

H1-02 Terminal S2 function selection 41 Reverse Run Command 41
H1-03 Terminal S3 function selection 24 External fault, N/O Detect always, coast stop 24
H1-04 Terminal S4 function selection 14 Fault reset 14
H1-05 Terminal S5 function selection 03 Multi-step speed reference 1 03
H1-06 Terminal S6 function selection 04 Multi-step speed reference 2 04
H1-07 Terminal S7 function selection 06 Jog frequency reference 06
H1-08 Terminal S8 function selection 08 External baseblock (N/O) 08

H2-01 Terminal M1/M2 Selection 0000 Closed: There is a run command present or the drive is 0000
outputting voltage
0006 Closed: Drive Ready 0001
H2-03 Terminal M5/M6 Selection 0002 Closed: Output frequency equals the speed reference (plus or 0002
minus the value set to L4-02)
H2-06 Output unit selection 0 0.1kWh unit 0
H2-07 Memobus Register MFDO1 Address 0001 0001
H2-08 Memobus Register MFDO1 Bit 0000 0000
H2-09 Memobus Register MFDO2 Address 0001 0001
H2-10 Memobus Register MFDO2 Bit 0000 0000

H3-01 Terminal A1 Signal Level Selection 0 0 to +10 V 0

H3-02 Terminal A1 Function Selection 00 Frequency Bias 00
H3-03 Terminal A1 Gain Setting 100.0 % 100.0 %
H3-04 Terminal A1 Bias Setting 0.0 % 0.0 %
H3-05 Terminal A3 Signal Level Selection 0 0 to +10 V 0
H3-06 Terminal A3 Function Selection 02 Auxiliary Frequency Reference 1 (used as a second frequency 02
reference)
H3-07 Terminal A3 Gain Setting 100.0 % 100.0 %
H3-08 Terminal A3 Bias Setting 0.0 % 0.0 %
H3-09 Terminal A2 Signal Level Selection 2 4 to 20 mA (9 bit input) 2
H3-10 Terminal A2 Function Selection 00 Frequency Bias 00
H3-11 Terminal A2 Gain Setting 100.0 % 100.0 %
H3-12 Terminal A2 Bias Setting 0.0 % 0.0 %
H3-13 Filter Avg time 0.03 sec 0.03 sec
H3-14 Analog Input Enable/Disable Selection 7 Enable All AI 7
H3-16 A1 Offset 0 0
H3-17 A2 Offset 0 0
H3-18 A3 Offset 0 0

H4-01 Multi-Function Analog 1 Monitor Selection 102 Output frequency 102

H4-02 Multi-Function Analog 1 Output Gain 100.0 % 100.0 %
H4-03 Multi-Function Analog 1 Output Bias 0.0 % 0.0 %
102 Output frequency 103
H4-05 Multi-Function Analog 2 Output Gain 50.0 % 50.0 %
H4-06 Multi-Function Analog 2 Output Bias 0.0 % 0.0 %
H4-07 Multi-Function Analog 1 Signal Level 0 0 to +10 V 0
Selection
H4-08 Multi-Function Analog 2 Signal Level 0 0 to +10 V 0
Selection

H5-01 Station address 1F 1F

DriveWizard Industrial for Windows (C) by Yaskawa America, Inc. 8/14

 Default
Parameter Value Information Setting
H5-02 Communication speed selection 3 9600 bps 3
H5-03 Communication parity selection 0 No parity 0
H5-04 Serial fault selection 3 Operation continued 3
H5-05 CE Detection Selection 1 Enabled 1
H5-06 Send wait time 5 ms 5 ms
H5-07 RTS control ON/OFF 1 Enabled 1
H5-09 CE detection time 2.0 sec 2.0 sec
H5-10 Output voltage monitor(Register No.25) unit 0 0.1V unit 0
H5-11 ENTER function selection of transmission 0 A constant is reflected and memorized when ENTER is input. 0
H5-12 Run Command Method Selection 0 FWD/STOP,REV/STOP type 0
H5-17 Operation Selection when Unable to Write 0 Cannot write into EEPROM 0
into EEPROM
H5-18 Motor Speed Monitor Filter Time 0 ms 0 ms

H6-01 Pulse train input function selection 0 Frequency reference 0

H6-02 Pulse train input scaling 1440 Hz 1440 Hz
H6-03 Pulse train input gain 100.0 % 100.0 %
H6-04 Pulse train input bias 0.0 % 0.0 %
H6-05 Pulse train input filter time 0.10 sec 0.10 sec
H6-06 Pulse train monitor selection 102 Output frequency 102
H6-07 Pulse train monitor scaling 1440 Hz 1440 Hz
H6-08 Pulse Train Min Input Frequency 0.5 Hz 0.5 Hz

L1-01 Motor protection selection 1 General-purpose motor protection 1

L1-02 Motor protection time constant 1.0 min 1.0 min
L1-03 MOL thermistor input 3 Operation continued 3
L1-04 MOL filter time 1 Coast to stop 1
L1-05 MOL reserved 1 0.20 sec 0.20 sec
L1-08 OL1 Current Lvl1 0.00 A 0.00 A
L1-13 Electronic thermal continues 1 Continue Electronic thermal 1

1 Enabled 0
L2-02 Momentary power loss ridethru time 1.0 sec 1.0 sec
L2-03 Min. baseblock time 0.7 sec 0.7 sec
L2-04 Voltage recovery time 0.3 sec 0.3 sec
L2-05 Undervoltage detection level 190 VDC 190 VDC
L2-06 KEB deceleration time 0.0 sec 0.0 sec
L2-07 Momentary recovery time 0.0 sec 0.0 sec
L2-08 KEB Frequency 100 % 100 %
L2-10 KEB detect time 50 ms 50 ms
L2-11 Desired DC Bus Voltage during KEB 260 VDC 260 VDC
L2-29 KEB Mode Selection 0 Single Mode KEB1 0

L3-01 StallP acceleration selection 1 Enabled 1

L3-02 StallP acceleration level 120 % 120 %
L3-03 StallP CHP level 50 % 50 %
L3-04 StallP deceleration selection 1 General Purpose - The deceleration will be stop when the Vdc 1
reaches the stall prevention level. And decelerates again when
L3-05 StallP running selection 1 Deceleration time 1
the Vdc recovered. 1
L3-06 StallP running level 120 % 120 %
L3-11 OV InhibitT selection 0 Disable 0
L3-17 Overvoltage Suppression and Deceleration 375 VDC 375 VDC
Stall and Desired DC Bus Voltage during
L3-20 Adjustment
Motor Stall Gain 1.00 1.00
L3-21 Deceleration rate operation gain 1.00 1.00
L3-23 StallP running level output auto reduction 0 Sets the stall prevention level throughout the entire frequency 0
range to the value in parameter L3-06.
DriveWizard Industrial for Windows (C) by Yaskawa America, Inc. 9/14
 Default
Parameter Value Information Setting
L3-24 Inertia conversion motor acceleration time 0.168 sec 0.168 sec
L3-25 Load inertia P 1.0 1.0
L3-26 Capacity of external capacitor 0 uF 0 uF
L3-27 StallP detection time 50 ms 50 ms
L3-35 Speed Agreement Width at Intelligent Stall 0.00 Hz 0.00 Hz
Prevention during Deceleration

L4-01 Speed agreement level 0.0 Hz 0.0 Hz

L4-02 Speed agreement width 2.0 Hz 2.0 Hz
L4-03 Speed agreement level +- 0.0 Hz 0.0 Hz
L4-04 Speed agreement width +- 2.0 Hz 2.0 Hz
L4-05 Reference loss selection 0 Stop 0
L4-06 Frequency reference at floss 80.0 % 80.0 %
L4-07 Conditions of Frequency detection 0 No detection during baseblock. 0

L5-01 Number of auto restart attempts 0 0

L5-02 Auto restart operation selection 0 Not output(Fault contact is not activated) 0
L5-04 Fault Reset Interval Time 10.0 sec 10.0 sec
L5-05 Auto restart selection 0 Count the number of restart which was carried out (G7 0
formula)

L6-01 Torque detection selection 1 0 Overtorque/undertorque detection disabled 0

L6-02 Torque detection level 1 150 % 150 %
L6-03 Torque detection time 1 0.1 sec 0.1 sec
L6-04 Torque detection selection 2 0 Overtorque/undertorque detection disabled 0
L6-05 Torque detection level 2 150 % 150 %
L6-06 Torque detection time 2 0.1 sec 0.1 sec
L6-08 Machine degradation detection selection 0 Machine degradation detection invalid 0
L6-09 Machine degradation detection speed level 110.0 % 110.0 %
L6-10 Machine degradation detection time 0.1 sec 0.1 sec
L6-11 Machine degradation detection start time 0 0

L8-01 DB resistor protect 0 Disabled 0

L8-02 Overheat pre-alarm level 110 °C 110 °C
L8-03 Overheat pre-alarm selection 3 Operation continued(monitor display only) 3
L8-05 Phase loss input selection 1 Enable 1
0 Disabled 1
L8-09 Ground protection selection 1 Enable 1
L8-10 Cooling fan control selection 0 Operates when inverter is running 0
L8-11 Cooling fan control delay time 60 sec 60 sec
L8-12 Ambient temperature 40 °C 40 °C
L8-15 OL characteristics at low speeds 1 L8-16,17 setting enable 1
L8-18 Software CLA selection 0 Software CLA disable(Gain=0) 0
L8-19 Frequency Reduction Rate during OH 0.8 0.8
Pre-Alarm
L8-32 MC/FAN power supply error selection 1 Coast to Stop 1
L8-38 Carrier frequency decel selection 2 Enabled in whole speed range 2
L8-40 Reduction carrier frequency time 0.50 sec 0.50 sec
L8-41 Current warning 0 Disable 0
L8-55 Internal DB Transistor Protection 1 Enable 1
Enable/Disable Selection

L9-03 Carrier Frequency Reduction Level Selection 0 Reduces the carrier frequency based on the drive rated current 0
that is not derated.

n1-01 Hunting-prevention selection 1 Enable 1

n1-02 Hunting-prevention gain 1.00 1.00
n1-03 Hunting-prevention time 10 ms 10 ms

DriveWizard Industrial for Windows (C) by Yaskawa America, Inc. 10/14

 Default
Parameter Value Information Setting
n1-05 Reverse hunting prev gain 0.00 0.00

n3-01 HSB deceleration frequency width 5% 5%

n3-02 HSB current 120 % 120 %
n3-03 HSB DWELL time 1.0 sec 1.0 sec
n3-04 HSB OL time 40 sec 40 sec
n3-13 Over exciting deceleration gain 1.10 1.10
n3-14 High Frequency Injection Selection at 0 Disable 0
Over-Excitation Deceleration
n3-21 Over slip inhibit current level 100 % 100 %
n3-23 Over Excitation Run 0 Disable 0

o1-01 Monitor selection 106 Output voltage 106

o1-02 Monitor selection after power up 1 Frequency reference 1
o1-03 Display scaling 0 0.01Hz units 0
o1-05 LCD Contrast Control 3 3

o2-01 LOCAL/REMOTE key enable/disable 1 Enabled 1

o2-02 Operation STOP key 1 Always enabled 1
o2-04 KVA selection 68 CIMR-A*2*0021*** 68
o2-05 Frequency Reference Setting Method 0 Enter key needed 0
Selection
o2-06 Operator detection 1 Inverter fault when the dig. Operator is disconnected 1
o2-07 Bidirectional when the inverter power is on 0 Forward run 0
o2-09 Initialize mode selection 1 American spec 1
o2-19 UV Param Set Sel 0 Disable 0

o3-02 Copy Allowed Selection 0 Disabled - No digital operator copy functions are allowed. 0

o4-02 Cumulative operation time selection 0 Cumulative time when the Inverter power is on 0
o4-03 Fan operation time setting 1793 1=10H 1793
1=10H
o4-05 Capacitor maintenance setting 0% 0%
o4-07 Rush-in prevention relay maintenance setting 0 % 0%
o4-09 IGBT maintenance setting 0% 0%

q1-01 Custom Parameter 0.00 % 0.00 %

q1-02 Custom Parameter 0.00 % 0.00 %
q1-03 Custom Parameter 0.00 % 0.00 %
q1-04 Custom Parameter 0.00 % 0.00 %
q1-05 Custom Parameter 0.00 % 0.00 %
q1-06 Custom Parameter 0.00 % 0.00 %
q1-07 Custom Parameter 0.0 % 0.0 %
q1-08 Custom Parameter 0.0 % 0.0 %
q1-09 Custom Parameter 0.0 % 0.0 %
q1-10 Custom Parameter 00 00
q1-11 Custom Parameter 0.0 % 0.0 %
q1-12 Custom Parameter 0 0
q1-13 Custom Parameter 0 0
q1-14 Custom Parameter 0 0
q1-15 Custom Parameter 0 0
q1-21 Custom Parameter 11000 11000
q1-22 Custom Parameter 11000 11000
q1-23 Custom Parameter 11000 11000
q1-24 Custom Parameter 11000 11000
q1-25 Custom Parameter 0000 0000

DriveWizard Industrial for Windows (C) by Yaskawa America, Inc. 11/14

 Default
Parameter Value Information Setting
q1-26 Custom Parameter 0000 0000

q2-01 Custom Parameter 30720 30720

q2-02 Custom Parameter 30720 30720
q2-04 Custom Parameter 100.0 % 100.0 %
q2-05 Custom Parameter 0.0 % 0.0 %
q2-06 Custom Parameter 100.0 % 100.0 %
q2-07 Custom Parameter 0.0 % 0.0 %
q2-08 Custom Parameter 100.0 % 100.0 %
q2-09 Custom Parameter 0.0 % 0.0 %
q2-10 Custom Parameter 0 0 to +10 V 0
q2-11 Custom Parameter 0 Not used 0
q2-12 Custom Parameter 0 Not used 0
q2-13 Custom Parameter 102 102
q2-14 Custom Parameter 103 103
q2-17 Custom Parameter 0000 0000
q2-18 Custom Parameter 0000 0000
q2-21 Custom Parameter 11000 11000
q2-22 Custom Parameter 11000 11000
q2-23 Custom Parameter 11000 11000
q2-24 Custom Parameter 11000 11000
q2-25 Custom Parameter 0000 0000
q2-26 Custom Parameter 0000 0000
q2-31 Custom Parameter 0F 0F
q2-32 Custom Parameter 0F 0F

q3-01 Custom Parameter 0.0 sec 0.0 sec

q3-02 Custom Parameter 0.0 sec 0.0 sec
q3-03 Custom Parameter 0.0 sec 0.0 sec
q3-04 Custom Parameter 0.0 sec 0.0 sec
q3-05 Custom Parameter 0.0 sec 0.0 sec
q3-06 Custom Parameter 0.0 sec 0.0 sec
q3-07 Custom Parameter 0.0 sec 0.0 sec
q3-08 Custom Parameter 0.0 sec 0.0 sec
q3-09 Custom Parameter 0.0 sec 0.0 sec
q3-10 Custom Parameter 0.0 sec 0.0 sec
q3-11 Custom Parameter 1 1sec 1
q3-12 Custom Parameter 43200 43200
q3-13 Custom Parameter 1 1sec 1
q3-14 Custom Parameter 43200 43200

q4-01 Custom Parameter 0.0 sec 0.0 sec

q4-02 Custom Parameter 0.5 sec 0.5 sec
q4-03 Custom Parameter 1 1
q4-04 Custom Parameter 1 1
q4-05 Custom Parameter 0.00 0.00
q4-06 Custom Parameter 0.00 % 0.00 %
q4-07 Custom Parameter 0.00 % 0.00 %
q4-08 Custom Parameter 0.00 % 0.00 %
q4-09 Custom Parameter 0.00 % 0.00 %
q4-10 Custom Parameter 0.00 % 0.00 %
q4-11 Custom Parameter 00 00
q4-12 Custom Parameter 1 1

DriveWizard Industrial for Windows (C) by Yaskawa America, Inc. 12/14

 Default
Parameter Value Information Setting
q4-13 Custom Parameter 1 1
q4-14 Custom Parameter 0.00 0.00
q4-15 Custom Parameter 1 1
q4-16 Custom Parameter 1 1
q4-17 Custom Parameter 0.00 0.00
q4-18 Custom Parameter 1 1
q4-19 Custom Parameter 1 1
q4-20 Custom Parameter 0.00 0.00
q4-21 Custom Parameter 0.00 0.00
q4-22 Custom Parameter 0.00 0.00
q4-23 Custom Parameter 0.00 0.00
q4-24 Custom Parameter 0.00 0.00
q4-25 Custom Parameter 00 00
q4-31 Custom Parameter 0 0
q4-32 Custom Parameter 0 0
q4-33 Custom Parameter 0 0

q5-01 Custom Parameter 0.0 sec 0.0 sec

q5-02 Custom Parameter 0.0 % 0.0 %
q5-03 Custom Parameter 0.0 % 0.0 %
q5-04 Custom Parameter 0.0 % 0.0 %
q5-05 Custom Parameter 0.0 % 0.0 %
q5-06 Custom Parameter 0.0 % 0.0 %
q5-07 Custom Parameter 0.0 % 0.0 %
q5-08 Custom Parameter 0.0 % 0.0 %
q5-09 Custom Parameter 0.00 % 0.00 %
q5-10 Custom Parameter 0.00 % 0.00 %
q5-11 Custom Parameter 0.00 % 0.00 %
q5-12 Custom Parameter 0.00 % 0.00 %
q5-13 Custom Parameter 0.00 % 0.00 %
q5-21 Custom Parameter 0.00 0.00
q5-22 Custom Parameter 0.00 0.00
q5-23 Custom Parameter 0.00 0.00
q5-24 Custom Parameter 0.00 0.00
q5-25 Custom Parameter 0.00 0.00
q5-26 Custom Parameter 0.00 0.00
q5-27 Custom Parameter 0.00 0.00
q5-28 Custom Parameter 0.00 0.00
q5-29 Custom Parameter 0.00 0.00
q5-30 Custom Parameter 0.00 0.00
q5-31 Custom Parameter 100.00 100.00
q5-32 Custom Parameter 0.00 0.00

q6-01 Custom Parameter 0 0

q6-02 Custom Parameter 10 10
q6-03 Custom Parameter 1.00 1.00
q6-04 Custom Parameter 1.0 sec 1.0 sec
q6-05 Custom Parameter 100.0 % 100.0 %
q6-06 Custom Parameter 100.0 % 100.0 %
q6-07 Custom Parameter 1.00 1.00
q6-09 Custom Parameter 4096 4096
q6-10 Custom Parameter 00 00

DriveWizard Industrial for Windows (C) by Yaskawa America, Inc. 13/14

 Default
Parameter Value Information Setting
q7-01 Custom Parameter 0 0
q7-02 Custom Parameter 1 1
q7-03 Custom Parameter 1 1
q7-04 Custom Parameter 1 1
q7-05 Custom Parameter 1 1
q7-06 Custom Parameter 1 1
q7-07 Custom Parameter 1 1
q7-08 Custom Parameter 0000 0000
q7-09 Custom Parameter 0000 0000
q7-10 Custom Parameter 0000 0000
q7-11 Custom Parameter 0000 0000
q7-12 Custom Parameter 0000 0000
q7-13 Custom Parameter 0000 0000
q7-14 Custom Parameter 0000 0000
q7-15 Custom Parameter 0000 0000
q7-16 Custom Parameter 0000 0000
q7-17 Custom Parameter 0000 0000
q7-18 Custom Parameter 0000 0000
q7-19 Custom Parameter 0000 0000
q7-20 Custom Parameter 0000 0000
q7-21 Custom Parameter 0000 0000
q7-22 Custom Parameter 0000 0000
q7-23 Custom Parameter 0000 0000
q7-24 Custom Parameter 0000 0000
q7-25 Custom Parameter 0000 0000
q7-26 Custom Parameter 0000 0000
q7-27 Custom Parameter 0000 0000
q7-28 Custom Parameter 0000 0000
q7-29 Custom Parameter 0000 0000
q7-30 Custom Parameter 0000 0000
q7-31 Custom Parameter 0000 0000
q7-32 Custom Parameter 0000 0000
q7-33 Custom Parameter 0000 0000
q7-34 Custom Parameter 0000 0000
q7-35 Custom Parameter 0000 0000
q7-36 Custom Parameter 0000 0000
q7-37 Custom Parameter 0000 0000

DriveWizard Industrial for Windows (C) by Yaskawa America, Inc. 14/14