PS113

Version : A.01
Issue Date : 2003/02/17
File Name : [Link]
Total Pages : 10

3-Channel Secondary Monitoring IC

 PS113

PS113
3-Channel Secondary Monitoring IC

General Description

PS113 is specially designed for switching power supply system. Three important
functions of PS113 are the following: over-voltage protection, short circuit protection
and power good signal generating.

OVP (Over Voltage Protection) monitors 5V, 12V and 3.3V to protect our power
supply and PC, when one of these supply voltages exceeds their normal operation
voltage.

Short circuit protection is done by UVP (Under Voltage Protection) . When power
supply is in short circuit, the supply voltages will be much smaller than their normal
operation voltages .We can use UVP to monitor our power supply whether it is in the
dangerous power load.

Power good signal generating notifies personal computer when power supply is
ready or power supply is going to shutdown, therefore it can provide a reliable power
supply environment.

Features
l Over voltage protection and lock out
l Short circuit protection and lock out
l Fault protection output with open drain output stage
l Open drain power good output signal for power good input
l Built-in 300ms power good delay
l 75ms delay for short-circuit turn on protection
l 38ms PSON control de-bounce
l 73us de-bounce for noise immunity
l Wide power supply range from 4V to 16V
l Pin to pin compatible with TPS3510
l Special care for AC power off
l Additional 12V UVP protection

3-Channel Secondary Monitoring IC Version ：A.01

-1-
 PS113

Block Diagram

FPO/
73uS
Vcc De-bounce
S Q
155KΩ R
VCCI
12 UV 1MΩ

8.5KΩ Vref delay

VCCI
12 OV
H : 4mS VCC
16.5KΩ Vref L : 4.5uS 30KΩ

VCCI
2KΩ
38mS PSON/
De-bounce 1.25V
VS5
58KΩ 4.5V 90KΩ
VCCI
5 UV

13.5KΩ Vref
VCCI
5 OV
VCCI

18.5KΩ Vref delay

1 1.13V
0
H : 75mS VCCI
L : 4.5uS
PGI
VS33 0.63V
39KΩ R
VCCI
VCCI
3.3 UV Q S

1.25V
22KΩ Vref
VCCI

3.3 OV
VCCI
29KΩ Vref

1MΩ

PGO
delay
73uS
De-bounce
H : 300mS
L : 4.5uS

Power On Internal Band-Gap Vref Clock

POR VCCI = 4V CLK
Reset Power Reference 1.25V Generator
GND

3-Channel Secondary Monitoring IC Version ：A.01

-2-
 PS113

Timing Chart

Vcc

PSON/

FPO/

PGI

VS12
VS5
VS33

PGO

Td1 Tb1
Td3
Td2

AC UVP/OVP PSON/ PSON/ PSON/ AC

turn on protect turn on turn off turn on turn off

V PGI 1.25V
1.13V
0.63V

Td1

Td2

OVP OVP/UVP OVP

3-Channel Secondary Monitoring IC Version ：A.01

-3-
 PS113

Pin Descriptions

Pin No PIN NAME Descriptions

1 PGI Power good input signal pin
2 GND Ground
3 FPO Inverted fault protection output ,open drain output stage
4 PSON ON/OFF control input pin
5 VS33 3.3V over/under voltage protection input pin
6 VS5 5.0V over/under voltage protection input pin
7 VCC Supply voltage/12V over voltage protection input pin
8 PGO Power good output signal pin , open drain output stage

Absolute Maximum Ratings

Parameter Rating Unit

Storage Temperature (Tstg ) -40 to +125 °C
Operating Temperature (Topr ) -40 to +125 °C
Supply Voltage (V CC) VCC -0.5 to +16.0 V
VS33,VS5 -0.5 to Vcc+0.5 V
Input Voltage Range (V I) PGI -0.5 to +16.0 V
PSON/ -0.5 to Vcc+0.5 V
FPO/ -0.5 to +16.0 V
Output Voltage Range (V O)
PGO -0.5 to Vcc+0.5 V
ESD Susceptibility* (V ESD ) > 2500 V
* Human Body Model (HBM).

Electrical characteristics , Vcc=12V, Ta = Full range. (unless otherwise specified)

Power Supply Section

Parameter Conditions MIN TYP MAX Unit

Supply Voltage 4.2 5.0 16.0 V

Supply Current VPSON/ = 5V 2 3 mA
Power On Reset Threshold Voltage (V POR) 3.6 V
Power On Reset Hysteresis (V HYST) ±0.6 V

3-Channel Secondary Monitoring IC Version ：A.01

-4-
 PS113

Electrical Characteristics (Continued)

Over-Voltage Section
Parameter Conditions MIN TYP MAX Unit

VS33 3.7 3.9 4.1 V

Over-V oltage Threshold VS5 5.7 6.1 6.5 V
VS12 13.2 13.8 14.4 V

Under-Voltage Section
Parameter Conditions MIN TYP MAX Unit

VS33 2.0 2.2 2.4 V

Under-Voltage Threshold VS5 3.3 3.5 3.7 V
VS12 8.5 9.0 9.5 V

PSON/, Analog Input

Parameter Conditions MIN TYP MAX Unit

Threshold Voltage 0.9 1.2 1.5 V

Hysteresis (V HYST) ±50 mV

PGI, Analog Input

Parameter Conditions MIN TYP MAX Unit

Threshold Voltage for start Td1 1.16 1.25 1.33 V

Threshold Voltage for start Td2 0.60 0.63 0.75 V
Threshold Voltage for mask OC,UV 1.05 1.13 1.21 V
Hysteresis (V HYST)* ±50 mV
* All of the comparator for PGI input in block diagram.

PGO, Open Drain Digital Output

Parameter Conditions MIN TYP MAX Unit

Leakage Current (I LKG ) VPGO=5V 5 uA

Low Level Output Voltage (V OL ) ISINK=10mA 5 0.4 0.4 V

3-Channel Secondary Monitoring IC Version ：A.01

-5-
 PS113

Electrical Characteristics (Continued)

FPO/, Open Drain Digital Output

Parameter Conditions MIN TYP MAX Unit

Leakage Current (I LKG ) VFPO/=5V 5 uA

ISINK=10mA 0.3 V
Low Level Output Voltage (V OL )
ISINK=30mA 0.7 V

Switching Characteristics, Vcc=5V, Ta = Full range.

Parameter Conditions MIN TYP MAX Unit

PGI to PGO Delay Time (Td1) 200 300 480 mS

Short Circuit Delay Time (Td2) 49 75 100 mS
PGO to FPO/ Delay Time (Td3 ) 2 4 6 mS
PSON/ De-bounce Time (Tb1) 24 38 61 mS
Noise De-glitch Time (Tb2) 47 73 120 uS

Application

S.P.S. Secondary Side

+5V Output

+3.3V Coil +3.3V Output

+12V Coil +12V Output

DV

= or
4.7K
RPGO

1 PGI PGO 8 PGO

2 GND VCC 7 +5VSB

+5VSB 3 FPO/ VS5 6

1K
PSON 4 PSON/ VS33 5

PS113
CPSON

CPGI

RPGI

Cby

Note1: Zener diode or resistor or both of them can be used in component X.

Note2: The bypass capacitor Cby suggests to be 0.1uF~ 10uF and layout nearby pin VCC.

3-Channel Secondary Monitoring IC Version ：A.01

-6-
 PS113

Package Specification

( 8-pin DIP )

E1 E eB

θ°

A2 A

Seating Plane

A1 L

b1 b S

0 5 10 15 20 25 mm

0.0 0.5 1.0 inch

Symbol Dimension in mm Dimension in inch NOTE

A 5.330 (MAX) 0.210 (MAX)
A1 0.380 (MIN) 0.015 (MIN)

A2 3.300 ± 0.130 0.130 ± 0.005

b 1.520 (TYP) 0.060 (TYP)
b1 0.460 (TYP) 0.018 (TYP)

D 9.200 ± 0.200 0.362 ± 0.008

E 7.620 (TYP) 0.300 (TYP)

E1 6.350 ± 0.130 0.250 ± 0.005

e 2.540 (TYP) 0.100 (TYP)

eB 9.000 ± 0.500 0.355 ± 0.020

L 9.020 ± 0.500 0.130 ± 0.020
S 0.790 (TYP) 0.031 (TYP)

θ° 0° ~ 15° 0° ~ 15°

3-Channel Secondary Monitoring IC Version ：A.01

-7-
 PS113

Package Specification (Continued)

( 8-pin SOP )

E H

h x 45°

A C

A1
θ
B e
L
Seating Plane

0 5 10 mm

0.0 0.2 0.4 inch

Dimension in mm Dimension in inch NOTE

Symbol
MIN. MAX. MIN. MAX.
A 1.35 1.75 0.0532 0.0688
A1 0.10 0.25 0.0040 0.0098
B 0.33 0.51 0.013 0.020
C 0.19 0.25 0.0075 0.0098
e 1.27BSC 0.050BSC
D 4.80 5.00 0.189 0.197
H 5.80 6.20 0.2284 0.2440
E 3.80 4.00 0.1497 0.1574
L 0.40 1.27 0.016 0.050
h 0.25 0.50 0.0099 0.0196
θ 0° 8° 0° 8°

3-Channel Secondary Monitoring IC Version ：A.01

-8-
 PS113

The products listed herein are designed for ordinary electronic applications, such as
electrical appliances, audio-visual equipment, communications devices and so on.
Hence, it is advisable that the devices should not be used in medical instruments,
surgical implants, aerospace machinery, nuclear power control systems,
disaster/crime-prevention equipment and the like. Misusing those products may
directly or indirectly endanger human life, or cause injury and property loss.

Silicon Touch Technology, Inc. will not take any responsibilities regarding the
misusage of the products mentioned above. Anyone who purchases any products
described herein with the above-mentioned intention or with such misused
applications should accept full responsibility and indemnify. Silicon Touch Technology,
Inc. and its distributors and all their officers and employees shall defend jointly and
severally against any and all claims and litigation and all damages, cost and expenses
associated with such intention and manipulation.

Silicon Touch Technology, Inc. reserve the right to make changes to their products or
to discontinue any product or service without notice, and advise customers to obtain
the latest version of relevant information to verify, before placing orders, that
information being relied on is current and complete.

3-Channel Secondary Monitoring IC Version ：A.01

-9-