Scribd
Upload
79 views4 pages

EDC PDF Edited

This document describes a 12V regulated power supply project for electronic devices and circuits. It includes a schematic diagram showing the design components, which are a plug, switch with lamp, 1000uF 25V capacitor, 1uF 25V capacitor, 4.7K ohms 1/4 watt resistor, 1N4007 diode, 12V stepdown transformer, LM7812 voltage regulator, fuse, LED, universal PCB and wires. It also shows the calculations for turns ratio, peak voltages, output peak and DC voltages, peak inverse voltage, output frequency, ripple factor and voltage regulation percentage. The power supply is designed to provide a regulated 12V output from a 220V AC input.

Uploaded by

jm m
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
79 views4 pages

EDC PDF Edited

This document describes a 12V regulated power supply project for electronic devices and circuits. It includes a schematic diagram showing the design components, which are a plug, switch with lamp, 1000uF 25V capacitor, 1uF 25V capacitor, 4.7K ohms 1/4 watt resistor, 1N4007 diode, 12V stepdown transformer, LM7812 voltage regulator, fuse, LED, universal PCB and wires. It also shows the calculations for turns ratio, peak voltages, output peak and DC voltages, peak inverse voltage, output frequency, ripple factor and voltage regulation percentage. The power supply is designed to provide a regulated 12V output from a 220V AC input.

Uploaded by

jm m
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd

1|Page

CEBU TECHNOLOGICAL UNIVERSITY – MAIN CAMPUS

ELECTRONICS ENGINEERING DEPARTMENT

SUMMER OF 2021

POWER SUPPLY PROJECT

FOR ELECTRONIC DEVICES AND CIRCUITS

ECE PC 212

12 V
REGULA
TED
DESIGN CALCULATIONS

POWER
Submitted by:
SUPPLY
MAYORGA, JIZSA MARIE B.

1191783 | BS ECE 2-7

Submitted to:

ENGR. GILBERT SILAGPO


2|Page

SCHEMATIC DIAGRAM

DESIGN COMPONENTS

PLUG SWITCH WITH LAMP 1000UF 25V CAPACITOR

1UF 25V CAPACITOR 4.7K OHMS ¼


WATTS RESISTOR 1N4007 DIODE

12V STEPDOWN TRANSFORMER LM7812


FUSE
3|Page

LED UNIVERSAL PCB WIRES

DESIGN CALCULATIONS

 Turns Ratio
Np = Vpri = 220 V = 18.33 V
         Vsec    12 V

Ns = Vsec(Np) = 12V (18.33V)  = 0.99982 V


           Vpri                  220 V

 Peak Voltages
Vrms = 0.707Vp                                    Vsec(p) = Vpri(Ns) = 311.174 (1) = 16.97621 V
220 = 0.707Vp                                                             Np               18.33
       0.707

Vpri (p) = 311.1739745 V

 Output Peak Voltage


Vo(p) = Vsec(p) – 0.7 = 16.97V – 0.7 = 16.27V

 Output DC Voltage
Vdc = 0.707Vo(p) = 0.707 (16.27) = 11.503V

 Peak Inverse Voltage


PIV = Vo (p) + 0.7 = 15.58 + 0.7 = 16.28 V

 Output Frequency
Fo = 2Fi = 2(60 Hz) = 120 Hz

 Ripple Factor
Idc = Vdc  = 11.503= 2.447 mA
           RL      4700

 Vdc = Vm – 4.17 Idc = 16.27 – 4.17 (2.447) = 16.26V


                                C                             1001
 Vr(rms) = 2.4 Idc = 2.4 (2.447) = 0.0059 V
                       C            1001

 R = vr(rms)   x 100 = 2.8      x 100 = 0.017%


4|Page

          vdc                   16.27

You might also like