19/4/2018 Hydraulic Fitting Thread Chart | Hydraulics Direct

Home ([Link] > Fitting Thread Chart ([Link]

s/[Link])

FLUID PORT AND CONNECTOR

Identi cation Guide

Quick Links
Abbreviations
Introduction
Fluid port and connector identi cation tools
American Connections
National Pipe Tapered Fuel (NPTF)
National Pipe straight mechanical (NSPM)
JIC 37° Flare (SAE J514)
SAE 45° Flare (SAE J512)
SAE Straight Thread O-ring (O-Ring Boss)
Flareless compression (SAE J514)
O-Ring Face Seal (SAE J1453)
SAE Inverted Flare (SAE J512)
Four-Bolt Flange (SAE J518 and ISO 6162)
O-Ring Pilot Threads
International Connections
British Standard Pipe
British Standard Pipe Parallel (BSPP)
British Standard Pipe Tapered (BSPT))
Flat Face Port with British Standard Pipe Parallel Threads (ISO 1179-1)
Flat Face Port with Metric Threads (ISO 9974-1)
ISO 6149 Metric Port and Stud Ends
Metric 600o Cone
Metric tube compression (DIN 2353 240 Cone)
Japanese Industrial Standard JIS 300 Flare
Komatsu 30° Flare (JIS Metric)

Abbreviations

NPTF National Pipe Tapered Fuel

NPSM National Pipe Straight Mechanical
ISO International Standards Organization
SAE Society of Automotive Engineers
JIC Joint Industrial Council
NFPA National Fluid Power Association
BSP British Standard Pipe
DIN Deutsche Industrial Norme
JIS Japanese Industrial Standard
BSPT British Standard Pipe Tapered
BSPP British Standard Pipe Parallel

[Link] 1/17
19/4/2018 Hydraulic Fitting Thread Chart | Hydraulics Direct

Introduction
Ports and connectors have wide applications in uid piping systems. Before you replace or add a hose or a tube to
your assembly, you should identify the port or connector required by your uid piping system. This guide will help
you to identify them with ease.

A thread standard de nes the form, angle, diameter, and pitch of a thread. ASME B1 .1 and ISO 261 are examples of
standards that are commonly used by thread manufacturers.

Some of the organizations that have developed commonly used thread standards include American Society of
Manufacturing Engineers, American National Standards Institute, International Organization for Standardization, SAE
International, British Association, and Deutsches Institut für Normung.

Fluid port and connector identi cation tools

Calipers
This tool is used for measuring inner and outer thread diameters

Thread Pitch Gauge

A thread pitch gauge is used for determining the number of threads per inch. It is also used for measuring the
thread-to-thread spacing in metric connections.

Accurate measurement of threads

Before you start measuring the threads of your uid pipe or tube, ensure that they are in good conditions. Distorted
or worn out threads can give you inaccurate measurements. After con rming that your threads are in good
conditions, measure their diameter and record. An I.D./O.D. caliper is a suitable tool for this. Match the dimensions
provided in this guide with your recorded measurements.

It is important to note that your measurements may not accurately match with the values provided in this guide. The
slight di erences are mainly caused by manufacturing tolerances.

After measuring the diameter of your threads, determine their spacing in threads per inch. In the case of metric
connections, measure the thread-to-thread distances. To get an accurate value, ensure that the thread pitch gauge is
tting well on the threads. Record the values and compare your measurements with the gures provided in this
guide.

Accurate measurement of four-bolt anges

To start with, use a caliper to determine the port hole diameter of your bolt. After recording the value, measure the
center to center bolt hole distance and record the longest spacing.

Dash numbers
Dash numbers are commonly used to describe the sizes of tubes and uid pipes. These abbreviations are widely
used in component ordering. To describe a uid pipe or a tube in dash numbers, only the numerator part of the
fraction is used. The denominator, always 16, is usually ignored. For instance, a -8 size means 8/16 or 1/2 an inch. It is
important to note that dash numbers are nominal.

Dash numbers are not applicable to metric threads. Metric measurements give actual sizes of a tube or a uid pipe.
For instance, M12x1.0 means that the threads have an outer diameter of 12 mm and an inter-thread spacing of 1.0
mm.

[Link] 2/17
19/4/2018 Hydraulic Fitting Thread Chart | Hydraulics Direct

American Connections
National Pipe Tapered Fuel (NPTF)
The NPTF is a dryseal thread. The male thread mates with the female thread and a seal is formed when the two are
crushed together i.e. threads deformation. Te on and pipe dope are commonly used when additional sealing is
needed. Although this connection is widely used in uid piping systems, the National Fluid Power Association (NFPA)
does not recommend it for hydraulic applications.

NB: Although the NPTF connector and BSPT connector are similar in appearance, the two are not interchangeable.

Inch size Dash size Threads per Inch Male Thread O.D. (in) Female thread O.D (in)
1 13 3
⁄8 -2 27 ⁄32 0.41 ⁄8 0.38
1 17 1
⁄4 -4 18 ⁄32 0.54 ⁄2 0.49
3 11 5
⁄8 -6 14 ⁄16 0.68 ⁄8 0.63
1 27 25
⁄2 -8 14 ⁄32 0.84 ⁄32 0.77
3
⁄4 -12 14 1 1⁄16 1.05 1 0.98
1 -16 11 1⁄2 1 5⁄16 1.32 1 1⁄4 1.24
1 1⁄4 -20 11 1⁄2 21
1 ⁄32 1.66 19
1 ⁄32 1.58
1 1⁄2 -24 11 1⁄2 1 29⁄32 1.90 1 13⁄16 1.82
2 -32 11 1⁄2 3
2 ⁄8 2.38 5
2 ⁄16 2.30

National Pipe straight mechanical (NPSM)

The male and female threads of the NSPM connection are straight. In addition, the male has a 300 internal chamfer
while the female has an inverted 300 seat. A mechanical connection is formed when the two halves are threaded
together. The tapered seat forms a leak-resistant joint. NSPM connections nd many applications in uid power
systems.

[Link] 3/17
19/4/2018 Hydraulic Fitting Thread Chart | Hydraulics Direct

NB: A NPSM female can form a seal with a chamfered NPTF male.

Inch size Dash size Threads per Inch Male Thread O.D. (in) Female thread O.D (in)
1 13 3
⁄8 -2 27 ⁄32 0.41 ⁄8 0.38
1 17 1
⁄4 -4 18 ⁄32 0.54 ⁄2 0.49
3 11 5
⁄8 -6 14 ⁄16 0.68 ⁄8 0.63
1 27 25
⁄2 -8 14 ⁄32 0.84 ⁄32 0.77
3
⁄4 -12 14 1 1⁄16 1.05 1 0.98
1 -16 11 1⁄2 5
1 ⁄16 1.32 1
1 ⁄4 1.24
1 1⁄4 -20 11 1⁄2 1 21⁄32 1.66 1 19⁄32 1.58
1 1⁄2 -24 11 1⁄2 1 29⁄32 1.90 1 13⁄16 1.82
2 -32 11 1⁄2 3
2 ⁄8 2.38 5
2 ⁄16 2.30

JIC 37° Flare (SAE J514)

This connection nds many applications in hydraulic systems. Both the JIC male and JIC female have a 37º are seat
and straight threads. The male and female are seats seal when the straight threads are engaged. The connection is
held mechanically by the straight threads of the male and female halves. It is important to note that most SAE J514
threads are identical to SAE 45º are threads but their seating angles are di erent.

Inch size Dash size Thread Size Male Thread O.D. (in) Female thread O.D (in)
1 5 5 9
⁄8 -2 ⁄16 - 24 ⁄16 0.31 ⁄32 0.27
3 3 3 11
⁄16 -3 ⁄8 - 24 ⁄8 0.38 ⁄32 0.34
1 7 7 13
⁄4 -4 ⁄16 - 20 ⁄16 0.44 ⁄32 0.39
5 1 1 15
⁄16 -5 ⁄2 - 20 ⁄2 0.50 ⁄32 0.45
3 9 9 17
⁄8 -6 ⁄16 - 18 ⁄16 0.56 ⁄32 0.51
1 3 3 11
⁄2 -8 ⁄4 - 16 ⁄4 0.75 ⁄16 0.69
[Link] 4/17
19/4/2018 Hydraulic Fitting Thread Chart | Hydraulics Direct
5 7 7 13
⁄8 -10 ⁄8 - 14 ⁄8 0.88 ⁄16 0.81
3
⁄4 -12 1 1⁄16 - 12 11
⁄16 1.06 1 0.98
7
⁄8 -14 1 3⁄16 - 12 1 3⁄16 1.19 1 1⁄8 1.10
1 -16 1 5⁄16-12 1 5⁄16 1.31 1 1⁄4 1.23
1 1⁄4 -20 1 5⁄8 - 12 1 5⁄8 1.63 1 9⁄16 1.54
1 1⁄2 -24 1 7⁄8 - 12 1 7⁄8 1.88 1 13⁄16 1.79
2 -32 2 1⁄2 - 12 2 1⁄2 2.50 2 7⁄16 2.42

SAE 45° Flare (SAE J512)

The SAE 45° Flare connections are commonly used for low pressure applications such as refrigerant lines, fuel lines,
and automotive piping systems. Both the SAE male and female halves have a 45° are seat. The threads of the two
halves engage to form a strong mechanical connection. The seal is formed on the 45° are seat. Except for the seat
angles, the SAE 45° Flare connectors are identical to JIC 37° Flare connectors.

Inch size Dash size Thread Size Male Thread O.D. (in) Female thread O.D (in)
1 5 5 9
⁄8 -2 ⁄16 - 24 ⁄16 0.31 ⁄32 0.27
3 3 3 11
⁄16 -3 ⁄8 - 24 ⁄8 0.38 ⁄32 0.34
1 7 7 13
⁄4 -4 ⁄16 - 20 ⁄16 0.44 ⁄32 0.39
5 1 1 15
⁄16 -5 ⁄2 - 20 ⁄2 0.50 ⁄32 0.45
3 5 5 9
⁄8 -6 ⁄8 - 18 ⁄8 0.63 ⁄16 0.57
1 3 3 11
⁄2 -8 ⁄4 - 16 ⁄4 0.75 ⁄16 0.69
5 7 7 13
⁄8 -10 ⁄8 - 14 ⁄8 0.88 ⁄16 0.81
3
⁄4 -12 1 1⁄16 - 14 11
⁄16 1.06 1 0.99
7
⁄8 -14 1 1⁄4 - 12 1
1 ⁄4 1.25 5
1 ⁄32 1.16
1 -16 1 3⁄8 - 12 1 3⁄8 1.38 1 9⁄32 1.29

SAE Straight Thread O-ring (O-Ring Boss)

SAE J1926-1 and ISO 11296-1

The male connector of the O-Ring Boss has an O-ring and a straight thread. The female port has a sealing face, a
chamfer, and a straight thread. The O-ring is compressed into the chamfer to form a seal. The threads of the two
halves engage to form a mechanically strong connection. This connection nds many applications in high pressure

[Link] 5/17
19/4/2018 Hydraulic Fitting Thread Chart | Hydraulics Direct

hydraulic systems.

Inch size Dash size Thread Size Male Thread O.D. (in) Female thread O.D (in)
1 5 5 9
⁄8 -2 ⁄16 - 24 ⁄16 0.31 ⁄32 0.27
3 3 3 11
⁄16 -3 ⁄8 - 24 ⁄8 0.38 ⁄32 0.34
1 7 7 13
⁄4 -4 ⁄16 - 20 ⁄16 0.44 ⁄32 0.39
5 1 1 15
⁄16 -5 ⁄2 - 20 ⁄2 0.50 ⁄32 0.45
3 9 9 17
⁄8 -6 ⁄16 - 18 ⁄16 0.56 ⁄32 0.51
1 3 3 11
⁄2 -8 ⁄4 - 16 ⁄4 0.75 ⁄16 0.69
5 7 7 13
⁄8 -10 ⁄8 - 14 ⁄8 0.88 ⁄16 0.81
3
⁄4 -12 1 1⁄16 - 12 11
⁄16 1.06 1 0.98
7
⁄8 -14 1 3⁄16 - 12 3
1 ⁄16 1.19 1
1 ⁄8 1.10
1 -16 1 5⁄16 - 12 1 5⁄16 1.31 1 1⁄4 1.23
1 1⁄4 -20 1 5⁄8 - 12 1 5⁄8 1.63 1 9⁄16 1.54
1 1⁄2 -24 1 7⁄8 - 12 7
1 ⁄8 1.88 13
1 ⁄16 1.79
2 -32 2 1⁄2 - 12 2 1⁄2 2.50 2 7⁄16 2.42

Flareless Compression (SAE J514)

The male of the areless tube has a 240 seat and a straight thread. The female half has a compression sleeve and a
straight thread. In addition to the sleeve, a female nut and a tube form part of the female connection. On the male,
the seal takes place between the 24O seat and the compression sleeve. On the female, the seal takes place between
the tubing and the compression sleeve. The threads engage to form a mechanically strong connection.

[Link] 6/17
19/4/2018 Hydraulic Fitting Thread Chart | Hydraulics Direct

Inch size Dash size Thread Size Male Thread O.D. (in) Female thread O.D (in)
1 5 5 9
⁄8 -2 ⁄16 - 24 ⁄16 0.31 ⁄32 0.27
3 3 3 11
⁄16 -3 ⁄8 - 24 ⁄8 0.38 ⁄32 0.34
1 7 7 13
⁄4 -4 ⁄16 - 20 ⁄16 0.44 ⁄32 0.39
5 1 1 15
⁄16 -5 ⁄2 - 20 ⁄2 0.50 ⁄32 0.45
3 9 9 17
⁄8 -6 ⁄16 - 18 ⁄16 0.56 ⁄32 0.51
1 3 3 11
⁄2 -8 ⁄4 - 16 ⁄4 0.75 ⁄16 0.69
5 7 7 13
⁄8 -10 ⁄8 - 14 ⁄8 0.88 ⁄16 0.81
3
⁄4 -12 1 1⁄16 - 12 11
⁄16 1.06 1 0.98
7
⁄8 -14 1 3⁄16 - 12 1 3⁄16 1.19 1 1⁄8 1.10
1 -16 1 5⁄16 - 12 5
1 ⁄16 1.31 1
1 ⁄4 1.23
1 1⁄4 -20 1 5⁄8 - 12 1 5⁄8 1.63 1 9⁄16 1.54
1 1⁄2 -24 1 7⁄8 - 12 1 7⁄8 1.88 1 13⁄16 1.79
2 -32 2 1⁄2 - 12 1
2 ⁄2 2.50 7
2 ⁄16 2.42

O-Ring Face Seal (SAE J1453)

This O-Ring Face Seal connection o ers an impressive leak resistance and it is suitable for applications that are up to
6000 psi. The male contact has an O-ring and a straight thread. The female contact has a at surface and a straight
thread. A seal is formed when the O-ring in the face of the male end is compressed onto the machined at surface
female seat. The swivel female nut mechanically holds the connection.

Inch size Dash size Thread Size Male Thread O.D. (in) Female thread O.D (in)
1 9 9 17
⁄4 -4 ⁄16 - 18 ⁄16 0.56 ⁄32 0.51
3 11 11 5
⁄8 -6 ⁄16 - 16 ⁄16 0.69 ⁄8 0.63
1 13 13 3
⁄2 -8 ⁄16 - 16 ⁄16 0.82 ⁄4 0.75
5 15
⁄8 -10 1 - 14 1 1.00 ⁄16 0.93
3
⁄4 -12 1 3⁄16 - 12 13
⁄16 1.19 1 1⁄8 1.11
1 -16 1 7⁄16 - 12 1 7⁄16 1.44 1 3⁄4 1.36
1 1⁄4 -20 1 11⁄16 - 12 11
1 ⁄16 1.69 5
1 ⁄8 1.61
1 1⁄2 -24 2-12 2 2.00 1 15⁄16 1.92

SAE Inverted Flare (SAE J512)

The inverted are nds many applications in automotive systems. A machined male connector has a 420 seat.A
ared male tubing has a 450 seat. The female end of the inverted are has a 420 seat that provides a sealing surface.
Threads engage to form a mechanically strong connection.

[Link] 7/17
19/4/2018 Hydraulic Fitting Thread Chart | Hydraulics Direct

Inch size Dash size Thread Size Male Thread O.D. (in) Female thread O.D (in)
1 5 5 9
⁄8 -2 ⁄16 - 28 ⁄16 0.31 ⁄32 0.27
3 3 3 11
⁄16 -3 ⁄8 - 24 ⁄8 0.38 ⁄32 0.34
1 7 7 13
⁄4 -4 ⁄16 - 24 ⁄16 0.44 ⁄32 0.39
5 1 1 15
⁄16 -5 ⁄2 - 20 ⁄2 0.50 ⁄32 0.45
3 5 5 9
⁄8 -6 ⁄8 - 18 ⁄8 0.63 ⁄16 0.57
7 11 11 5
⁄16 -7 ⁄16 - 18 ⁄16 0.69 ⁄8 0.63
1 3 3 23
⁄2 -8 ⁄4 - 18 ⁄4 0.75 ⁄32 0.70
5 7 7 13
⁄8 -10 ⁄8 - 18 ⁄8 0.88 ⁄16 0.81
3
⁄4 -12 1 1⁄16 - 16 11⁄16 1.06 1 1.00

Four-Bolt Flange (SAE J518 and ISO 6162)

The Four-Bolt Flange is suitable for connecting 1/2" to 3" hoses and tubings and it is widely used in uid power
[Link] O-ring seats on the ring groove of the male. The seal takes place between the O-ring on the male and
the smooth face of the female port. Four bolts and two clamp halves hold the connection in place.

[Link] 8/17
19/4/2018 Hydraulic Fitting Thread Chart | Hydraulics Direct

SAE J518 flanges are available in two pressure categories: standard (code 61) and high pressure (code 62).

Inch size Dash size Code 61 Bolt Spacing Code 61 Flange O.D. Code 62 Bolt Spacing Code 62 Flange O.D.
1
⁄2 -8 1 1⁄2 1 3⁄16 1 19⁄32 1 1⁄4
3
⁄4 -12 1 7⁄8 1 1⁄2 2 1 5⁄8
1 -16 2 1⁄16 1 3⁄4 2 1⁄4 1 7⁄8
1 1⁄4 -20 2 5⁄16 2 2 5⁄8 2 1⁄8
1
1 ⁄2 -24 2 3⁄4 2 3⁄8 3 1⁄8 2 1⁄2
2 -32 3 1⁄16 2 13⁄32 3 13⁄16 3 1⁄8
2 1⁄2 -40 3 1⁄2 3 5⁄16 n/a n/a
3 -48 4 3⁄16 4 n/a n/a

O-Ring Pilot Threads

The O-Ring Pilot Threads connection is commonly used in vehicle and commercial air conditioning systems. The male
and female ends have a pilot and a seal is formed when the O-ring is compressed. The pilot can either be long or
short. Threads engage to form a mechanically strong connection.

Male Thread Female thread

Inch size Dash size
Thread size Thread O.D. Thread size Thread I.D.
3 5 5 5 9
⁄8 -6 ⁄8 - 18 ⁄8 ⁄8 - 18 ⁄16
1 3 3 3 11
⁄2 -8 ⁄4 - 18 ⁄4 ⁄4 - 16 ⁄16

[Link] 9/17
19/4/2018 Hydraulic Fitting Thread Chart | Hydraulics Direct
5 7 7 7 13
⁄8 -10 ⁄8 - 18 ⁄8 ⁄8 - 14 ⁄16
3
⁄4 -12 1 1⁄16 - 16 1 1⁄16 1 1⁄16 - 14 1

Long pilot Short pilot

Inch size Dash size
Bead O.D. (in) Pilot Length (in) Bead O.D. (in) Pilot Length (in)
3
⁄8 -6 0.52 0.28 0.52 0.19
1
⁄2 -8 0.64 0.39 0.64 0.19
5
⁄8 -10 0.77 0.39 0.77 0.19
3
⁄4 -12 0.91 0.39 0.91 0.19

International Connections
British Standard Pipe
The British connections are available in two classes: British Standard Pipe Parallel (BSPP)and British Standard Pipe
Tapered (BSPT).

British Standard Pipe Parallel (BSPP)

The BSPP male end has a 300 seat. The tapered nose of the female swivel seals on the 300 seat of the male. Although
the male end is similar to the American National Pipe Straight Mechanical (NPSM) male, the two are not
interchangeable because their thread pitches are di erent.

Inch size Dash size Thread Size Male Thread O.D. (in) Female thread O.D (in)
1 1 3 11
⁄8 -2 ⁄8 - 28 ⁄8 0.38 ⁄32 0.35
1 1 33 15
⁄4 -4 ⁄4 - 19 ⁄64 0.52 ⁄32 0.47
3 3 21 19
⁄8 -6 ⁄8 - 19 ⁄32 0.65 ⁄32 0.60
1 1 13 3
⁄2 -8 ⁄2 - 14 ⁄16 0.82 ⁄4 0.75
5 5 7 13
⁄8 -10 ⁄8 - 14 ⁄8 0.88 ⁄16 0.80
3 3
⁄4 -12 ⁄4 - 14 11⁄32 1.04 31
⁄32 0.97
5 7
1 -16 1 - 11 1 ⁄16 1.30 1 ⁄32 1.22
1 1⁄4 -20 1 1⁄4 - 11 1 21⁄32 1.65 1 9⁄16 1.56
1 1⁄2 -24 1 1⁄2 - 11 1 7⁄8 1.88 1 25⁄32 1.79
[Link] 10/17
19/4/2018 Hydraulic Fitting Thread Chart | Hydraulics Direct

2 -32 2 - 11 2 11⁄32 2.35 2 1⁄4 2.26

British Standard Pipe Tapered (BSPT)

The tapered male of the BSPT mates with a tapered female. The seal takes place on the threads. Although the BSPT
male end is similar to the National Pipe Tapered Fuel (NPTF), the two are not interchangeable because their thread
form and sizes are di erent.

Inch size Dash size Thread Size Male Thread O.D. (in) Female thread O.D (in)
1 1 3 11
⁄8 -2 ⁄8 - 28 ⁄8 0.38 ⁄32 0.35
1 1 33 15
⁄4 -4 ⁄4 - 19 ⁄64 0.52 ⁄32 0.47
3 3 21 19
⁄8 -6 ⁄8 - 19 ⁄32 0.65 ⁄32 0.60
1 1 13 3
⁄2 -8 ⁄2 - 14 ⁄16 0.82 ⁄4 0.75
5 5 7 13
⁄8 -10 ⁄8 - 14 ⁄8 0.88 ⁄16 0.80
3 3
⁄4 -12 ⁄4 - 14 11⁄32 1.04 31
⁄32 0.97
5 7
1 -16 1 - 11 1 ⁄16 1.30 1 ⁄32 1.22
1 1⁄4 -20 1 1⁄4 - 11 1 21⁄32 1.65 1 9⁄16 1.56
1 1⁄2 -24 1 1⁄2 - 11 1 7⁄8 1.88 1 25⁄32 1.79
11 1
2 -32 2 - 11 2 ⁄32 2.35 2 ⁄4 2.26

Flat Face Port with British Standard Pipe Parallel Threads (ISO 1179-1)
DIN 3852, Part 2

The parallel threads form a seal using a variety of sealing rings or washers. The seal takes place between the male
end and the machined at surface of the female.

[Link] 11/17
19/4/2018 Hydraulic Fitting Thread Chart | Hydraulics Direct

Flat Face Port with Metric Threads (ISO 9974-1)

DIN 3852, Part 1

The parallel threads form a seal using a variety of sealing rings or washers. The seal takes place between the male
end and the machined at surface of the female.

ISO 261 Metric threads

[Link] 12/17
19/4/2018 Hydraulic Fitting Thread Chart | Hydraulics Direct

Metric Thread Size Male Thread O.D. (mm) Female Thread I.D (mm)
M8 x 1.0 8 7
M10 x 1.0 10 9
M12 x 1.5 12 10.5
M14 x 1.5 14 12.5
M16 x 1.5 16 14.5
M18 x 1.5 18 16.5
M20 x 1.5 20 18.5
M22 x 1.5 22 20.5
M24 x 1.5 24 22.5
M26 x 1.5 26 24.5
M27 x 2.0 27 25
M33 x 2.0 33 31
M36 x 2.0 36 34
M42 x 2.0 42 40
M45 x 2.0 45 43
M48 x 2.0 48 46

ISO 6149 Metric Port and Stud Ends

ISO 261 threads & O-ring seal

The male connector of the ISO 6149 connection has an O-ring and a straight thread. The female half has a machined
surface, a chamfer, and a straight thread. The O-ring on the male sits on the chamfer of the female port. The ISO
6149 connection is similar to the SAE J1926-1O-ring Boss except that the former has metric threads. The O-ring on
the male connector is compressed into the chamfer to create a seal. The straight threads engage to form a
mechanically strong connection.

Metric Thread Size Male Thread O.D. (mm) Female Thread I.D (mm)
M8 x 1.0 8 7
M10 x 1.0 10 9
M12 x 1.5 12 10.5
M14 x 1.5 14 12.5
M16 x 1.5 16 14.5
M18 x 1.5 18 16.5
M22 x 1.5 22 20.5
M27 x 2.0 27 25

[Link] 13/17
19/4/2018 Hydraulic Fitting Thread Chart | Hydraulics Direct

M33 x 2.0 33 31
M42 x 2.0 42 40
M48 x 2.0 48 46
M60 x 2.0 60 58

Metric 60° Cone

DIN 7631

The male of the Metric 60° Cone connection has a 60° recessed cone and a straight thread. The female half has a
globeseal seat and a straight thread. The seal takes place between the 60° recessed cone and the tapered nose of the
female. The threads of the two halves engage to form a mechanically strong connection. This connection nds many
applications in hydraulic systems.

Pipe/Tube O.D. (mm) Metric Thread Size Male Thread O.D. (mm) Female Thread I.D (mm)
6 M12 x 1.5 12 10.5
8 M14 x 1.5 14 12.5
10 M16 x 1.5 16 14.5
12 M18 x 1.5 18 16.5
15 M22 x 1.5 22 20.5
18 M26 x 1.5 26 24.5
22 M30 x 1.5 30 28.5
28 M38 x 1.5 38 36.5
35 M45 x 1.5 45 43.5
52 M52 x 1.5 52 50.5

Metric Tube Compression (DIN 2353 24° Cone)

The male has a 240 Cone and a straight thread. The three female connectors have straight threads and a sealing
surface. The seal takes place between the 240 Cone on the male connector and the sealing areas on the females.

Fittings are available in two series: the DIN 2353 L (light) and the DIN 2353 S (heavy) classes. Each series has its own

[Link] 14/17
19/4/2018 Hydraulic Fitting Thread Chart | Hydraulics Direct

tube sizes and thread dimensions as shown in the table below:

DIN 2353 L Tube O.D.(mm) DIN 2353 S Tube O.D. (mm) Metric Thread Size Male Thread O.D. (mm) Female Thread I.D (mm)
6 M12 x 1.5 12 10.5
8 6 M14 x 1.5 14 12.5
10 8 M16 x 1.5 16 14.5
12 10 M18 x 1.5 18 16.5
12 M20 x 1.5 20 18.5
15 14 M22 x 1.5 22 20.5
16 M24 x 1.5 24 22.5
18 M26 x 1.5 26 24.5
22 20 M30 x 2.0 30 28
28 25 M36 x 2.0 36 34
30 M42 x 2.0 42 40
35 M45 x 2.0 45 43
42 38 M52 x 2.0 52 50

Japanese Industrial Standard JIS 300 Flare

The male has a 30° seat and a straight [Link] female half has a 300 seat and a straight [Link] connection is
similar to 37° Flare. Its 30° seat and BSPP-like thread dimensions di erentiate it from the American 37° Flare.

[Link] 15/17
19/4/2018 Hydraulic Fitting Thread Chart | Hydraulics Direct

Inch size Dash size Thread Size Male Thread O.D. (in) Female thread O.D (in)
1 1 3 11
⁄8 -2 ⁄8 - 28 ⁄8 0.38 ⁄32 0.35
1 1 33 15
⁄4 -4 ⁄4 - 19 ⁄64 0.52 ⁄32 0.47
3 3 21 19
⁄8 -6 ⁄8 - 19 ⁄32 0.65 ⁄32 0.60
1 1 13 3
⁄2 -8 ⁄2 - 14 ⁄16 0.82 ⁄4 0.75
5 5 7 13
⁄8 -10 ⁄8 - 14 ⁄8 0.88 ⁄16 0.80
3 3
⁄4 -12 ⁄4 - 14 11⁄32 1.04 31
⁄32 0.97
5 7
1 -16 1 - 11 1 ⁄16 1.30 1 ⁄32 1.22
1 1⁄4 -20 1 1⁄4 - 11 1 21⁄32 1.65 1 9⁄16 1.56
1 1⁄2 -24 1 1⁄2 - 11 1 7⁄8 1.88 1 25⁄32 1.79
11 1
2 -32 2 - 11 2 ⁄32 2.35 2 ⁄4 2.26

Komatsu 30° Flare (JIS Metric)

The Komatsu 30° Flare has parallel metric threads and a 30° seat. This connection is widely used on Komatsu
equipment. The JIS metric connection is similar to the JIS 300 are, except that the latter has BSPP-like thread
dimensions.

Dash Size Metric Thread Size Male Thread O.D. (mm) Female Thread I.D (mm)
-6 M18 x 1.5 18 16.5
-8 M22 x 1.5 22 20.5
-10 M24 x 1.5 24 22.5
-12 M30 x 1.5 30 28.5
-16 M33 x 1.5 33 31.5
-20 M36 x 1.5 36 34.5
-24 M42 x 1.5 42 40.5

[Link] 16/17
19/4/2018 Hydraulic Fitting Thread Chart | Hydraulics Direct

ABOUT US

MY ACCOUNT

PRODUCTS

HELPFUL INFO

QUESTIONS? CALL US!

Copyright 2018 Hydraulics Direct (/[Link])

FOLLOW US
([Link]
([Link]

TRUSTED SELLER

Built with Volusion ([Link]

[Link] 17/17