Scribd
Upload
505 views24 pages

ATS Takada

Uploaded by

aaronchestercruz
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
505 views24 pages

ATS Takada

Uploaded by

aaronchestercruz
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
BS88 Series BS88/BS88-LN ATS CONTROLLER OPERATING MANUAL ATS CONTROLLER BS86/BS88-LN ATS CONTROL MODULE CONTENT 1 SUMMARY... 2 PERFORMANCE AND CHARACTERISTICS . 3. SPECIFICATION... 4 OPERATING 4.1 OPERATION PANEL... 42 Key FUNCTION DESCRIPTION, 5 LCD DISPLAY... SL MAINSCREEN cn 52 MAINS MENU INTERFACE. aebnseeiee 6 TEST GENERATOR OPERATION......... 7 CONFIGURATION PARAMETERS... TL PARAMETERS TABLE wns 7.2 INPUT/OUTPUTFUNCTION DESCRIPTION trol 8 TIMING START GENERATOR... 9 DATE AND TIME SETTING.. 10 CONTROLLER INFORMATION... 11 ATS OPERATION. IL MANUAL OPERATION. 1.2 AuTowaric operation 13. ATS power st 12 COMMUNICATION CONFIGURATION.. 13 DESCRIPTION OF CONNECTING TERMINAL.. 14 TYPICAL WIRING DIAGRAM 15 INSTALLATION 16 FAULT FINDING .. BS88 Series ATS CONTROLLER —ISSUE2010-07-08 Version 14 Page 2 of 23 BS88/ BS88-LN_ATS CONTROL MODULE 1 SUMMARY BS88 series ATS controller with a programmable function, automatic measurement, LCD display, digital communications, as one of the intelligent dual-supply switching module. It combines digital, intelligent, networking, measurement and control process automation, disoperation, in order to reduce the faults during operation. It is the best ideal option in ATS. BS88 series ATS controller be made of microprocessor as its core, can accurately detect extended-spectrum 2-way-3-phase voltage and also make accurate judgment and output passive control switch under the abnormal voltage (over or under, miss phase and over or miss frequency). This controller has full consideration in various application of ATS (automatic transfer system) can be directly used for Intelligent ATS, Contactor ATS, Circuit Break ATS etc. It have compact structure, advanced circuits, simple wiring and high reliability, be widely used in Electric power, Telecommunications, Petroleum, Coal, Metallurgy, Railways, Municipal, Intelligent building, Electrical devices, Automatic control and Testing system etc. 2 PERFORMANCE AND CHARACTERISTICS |= System type can set for: Mains (1#) & Mains (2#), Mains (1#) & Gens (2#), Gens (1#) & Mains (2#), Gens (1#) & Gens (2#) The LCD 128x64, take backlit, two languages (simplified Chinese and English) display, and gentle press key for operation, | Measure and shows 2-way 3 phase voltage and frequency parameters: Wayé# Way#2 Line-Line voltage (Uab, Ube, Uca) —_Line-Line voltage (Uab, Ubc, Uca) Phase-Nature voltage (Ua, Ub, Uc) Phase-Nature voltage (Ua, Ub, Uc) Frequency (F1) Frequency (F2) With over voltage, under voltage, loss of phase, reverse phase sequence, over frequency, under frequency functions. With the auto/manual operation mode. In manual mode, may enforce switch to close or open. = All parameters can be set in the field. Apply for two-stage password to ensure authorized staff operation only. S88 Series ATS CONTROLLER —ISSUEZ010-07-05 Version 14 Page Sof 23 BS88/BS88-LN ATS CONTROL MODULE ™ Can be set as on-load/off-load mode in the field for start genset. ® Can make switch to re-close when switch is opened accidentally or make switch to power off then re-close. Closing output can be set as pulse or continuous output. Applicable for ATS of one OFF segment, two OFF segments and none OFF segment. With design of two way separate of N circuitries. Real-time clock (RTC). Can start or stop genset automatic on scheduler. Also be set as single time operation, monthly or weekly, and whether with load or not. Can control two gensets to work in cycle, even the genset running time and interval rest time can be set. Widely range of DC power supply. Max.80V DC input can be endured in an instant, Bigger space between connecting terminals of AC input. Max.625V input voltage. With standard insulated RS485 communication interface port. With "remote controlling, remote measuring, remote communication" function by the ModBus communication protocol. Can check the status of controller (including of switch auxiliary output, over-voltage, and under-voltage etc.) Suitable for various AC systems (3-phase 4-wires, 3-phase 3-wires, single-phase 2-wires, and 2-phase 3-wire). Modular configuration design, flame-resisting ABS plastic shell, inserted type connection terminals and built-in installation. Compact structure with easy installation 3 SPECIFICATION 1. DC 8.0V~35.0V, power supply constantly, Operating voltage | 2. AC160V~280V (BS8B-LN) during AC power L1N1/L2N2 supply) Power catriation <3W (Standby mode: <2w) [AC system BS88 BS88-LN AC voltage Input | 3-phase 4-wire(L-L) | 80~625V 80~480V S-phase 3-wire(L-L)[80-625V Not used 8S88 Series ATS CONTROLLER ISSUEZ010-07-05 Version 14 Page 4 of 23 BS86/BS88-LN_ATS CONTROL MODULE t-phase 2-wire(L-N) | 50~360V 50~280V 2-phase 3-wire(A-B) | 80~625V 80~480V Rated frequency | 60/60Hz Close and Open tage rel Tip Relay oupur_| TOA2S0VAC Free voltage relay output Programmable relay output 1GA/TA250VAC_ Free voltage relay output capacity Digital Input Connecting to GND is active ‘Communication | RS485, MODBUS Protocol Dimensions 209mmx153mmxS5mm Panel cutout 186mm x 141mm aeons Temp. | Temperature: (-25~-+70)"C; Humidity: (20~90)% Storage condition ‘Temperature: (-30-+80)°C Protection rank P58: Front of module when module is installed into the control panel with the optional sealing gasket. IP42: Front of module when module is installed into the control panel without being sealed to the panel. Object: Between the input/output/ power supply. Insulation strength | Quote from standard: IEC688-1992. Test method: AC1.5kV/1min in current 5mA. Weight 0.8kg(BS88)/1.0kg(BS88-LN. S88 Series ATS CONTROLLER ISSUE2010-07-05 Version 14 Page 6 of 23 BS88/ BS88-LN_ATS CONTROL MODULE 4 OPERATING 4.1 OPERATION PANEL ATS CONTROLLER 4.2 KEY FUNCTION DESCRIPTION The key function is used to transfer 1# power to load MW Close key | in manual mode. unk The key function is used to transfer 1# or 2 power Mee to off-load in manual mode. The key function is used to transfer #2 powers to Ni-Close key | kaad x anced mode Manual key —_| The key function is used to initiate manual operation. ‘Automatic key The key function is used to i operation. iate automatic Pressing the key can directly enter commissioning @| @ jeloeeoe Tesi key interface. Pressing the key, enter menu interface; Holding Pressing the key go back to the main current arnt | operating from that interface. When a fault alarm controller, holding pressing the key can eliminate fault alarm. Page down Page tur. In the adjustment parameters menu as Idecrease numerical increases. BS88 Series ATS CONTROLLER —ISSUE2010-07-05 Version 1.4 Page 6 of 23 BS88/BS88-LN_ATS CONTROL MODULE 5 LCD DISPLAY 5.1. MAIN SCREEN This screen will show: lineine voltage (L1-L2, L2-L3, and L3-L1), frequency and controller present status is in manual (auto) mode. This screen show: 1# and 2# of the three phase voltage (L-N), real-time clock and controller working state. This screen show: 3 phase load current, active power, apparent power, power factor and work state of controller. LCD display I# operating state of power supply. LCD display Il# operating state of power supply. LCD displays other operating state. Present status is in manual (auto) mode. Display priority of the #1 status (upper to lower) 1# Fail to When 1# breaker occur closing failure, closed a this will display. 9 | te Failto Fut |When 1# breaker occur opening break failure, this will display. 3. | 1#Over Volt | Indication | When 1# source occur over voltage, this will display. 1# Loss of fication | When any of 1# three phases is miss, 4 | Phase Indication | this will display. ication _| When 1# source occur over frequency, 5 | 1# Over Fi ['#Over Freq | Indication | wis wil display. BS88 Series ATS CONTROLLER ISSUEZ010-07-05 Version 14 Page 7 of 23 BS88/[Link] ATS CONTROL MODULE When 1# source occur under frequency, this will display. When 1# source occur under voltage, 6 | 1# Under Freq Indication 7 | 1# Under Volt Indication this will display. is error, this a | 1#Phase Waring | When tit phase sequence i sequence fault will display. : When 1# source voltage is normal, this 9 | *#VoItnormal | Indication | si gispiay Display priority of the #2 status (upper to lower) 4 | 2#Failto Faut | When 2# breaker occur closing failure, Closed fae this will display. 2 | 2#Failto Faut [When 2# breaker occur opening Break oaks failure, this will display. ‘cation | When 2# sources occur over voltage, 3 |2# Over Volt | Indication | he wil etplay 4 | BE Loss of Indication | When any of 2# three phases is miss, Phase this will display. 5 |2#OverFreq | Indication [When 2# sources occur over frequency, this will display. When 2# sources occur under frequency, this will display. 6 | 2#Under Freq | Indication 7 | 2# Under Voit | Indication | When 2# sources occur under voltage, this will display. 2# Phase When 2# phase sequence is error, this 8 | sequence faut | 2°93 | wit display 9 | 2#Volt normal | Indication | When 2# sources voltage is normal, this will display. Display priority of the other status (upper to lower) Engine starting 2 | Breaking compulsorily Display that engine has start Breaking compulsorily input is active. Load current is over than the setting 3 | Load over current 7 limit and exceed the setting delay. Faults: when alarm occurs, alarm lamp will flash and this alarm signal will continue until long pressing @ key to reset. Warning: when warming occurs, alarm lamp will flash and will not latch. When a BS88 Series ATS CONTROLLER —ISSUEZ010-07-05 Version 1.4 Page 6 of 23 BS86/ BS88-LN_ATS CONTROL MODULE warning is inactive, alarm lamp will latch. 5.2 MAINS MENU INTERFACE Inthe screen, press © key, can enter the main menu interface. Press © key choose different parameters (the current line anti-black) and then press ®) key to confirm, can enter the corresponding display screen. 6 TEST GENERATOR OPERATION On the main screen press © key and directly into the test generator operation interface, the screen will show as following: Press ©) key to select corresponding function, and press ®) key to confirm. STOP TO TEST: This will stop a start generator signal immediately. TEST OFF-LOAD: This will send out a start generator signal immediately. After 2# source is normal, if 1# source is normal, the ATS will not act. The ATS will transfer the load to 2# ‘only when 1# source is abnormal. After 1# source return normal, the ATS will transfer the load to 1#. Here the start generator signal output will keep. TEST ON-LOAD: This will send out a start generator signal immediately. After 2# ‘source is normal, the ATS will transfer the load to 2# source immediately regardless Of 1# source normal whether or not. CYCLE START: When choosing this mode, generator start-signal will cyclic output according to mains status, user can set the cyclic time. If generator fault of input-signal, no longer send Start-signal. If in manual mode, will keep the current status and cancel cycle start. Conditions under this mode: ie [Link] automatic mode. [Link] port setting: 1# engine start output (Normal Output) and 2 # engine start ‘output (Normal Output). 8888 Series ATS CONTROLLER ISSUE2010.07.05 Version 74 Page 9 of 23 BS88/ BS88-LN_ATS CONTROL MODULE [Link] port setting: 1# generator fault input and 2# generator fault input. [Link] set the and the . [Link] system type set must as Gens(#)&Gens(2#). Note: In manual mode, after choose commissioning, generator will output start-signal immediately, but the ATS will not transfer to load automatically except for operation manually by pressing key mounted on the front panel. 7 CONFIGURATION PARAMETERS. In the main interface, press ® key, choose [Link] setting and then press ® key, to enter interface of confirming password. Input password value 0-9 by ©) key, and to shift Right by ®) key. Press the ® key in the fourth of password to confirm. If password correct and enter into the parameter mains interface. While error, directly exit to return to main interface. Factory Default Password is: 1234. Press © key to tum over and set Parameters. While setting the current configuration parameters according to press ® key. Then enter current parameter model, and the current value of the first line screen display against the first black. Press ©) key to change number, press @) key to shit position, and press @) key again to confirm in the last number position If the setting value within limits, the value is stored into the intemal controller FLASH. Beyond the limits, parameters will can't be saved. In the parameters setting interface, long time press @) key will back to the main display screen 7.1 PARAMETERS TABLE Parameters item table N It is the delay of #4 power from lormal delay of 1 Y oe (0-9999)s 10 | voltage abnormal to voltage normal. ‘Abnormal delay It is the delay of #1 power from 02 | ort (0-9999)s 5 | voltage normal to voltage abnormal. Normal Delay It is the delay of #2 powers 03 | or oe (0-9999)s 10 | from voltage abnormal to voltage normal, 04 | Abnormal (0-9999)S 5 it is the delay of #2 powers BSBB Series ATS CONTROLLER —ISSUEZ010-07-05 Version 14 Page 10 of 33 BS88/ BS88-LN_ATS CONTROL MODULE Delay of 2# from voltage normal to voltage abnormal ; Breaker close pulse. If it is set 05 || Cesedtime: | (e208 5 | to z0F0, the output will hold 06 _| Open time (1-20)8 5 __| Breaker open pulse. It is the delay from #1 power Transfer ‘opened to #2 powers starts to 07 interval (o-se8)s * | close or from #2 power opened to #1 power start to close. ‘Afier the module has received Exceed transfer a close state input, the breaker 8 | time coe 9-0 | close outputs continue to hold until the delay is expended. When the breaker fail to close for the first time, the module will open breaker, and then attempt Again closed to close for the second time, if 9 | time (0-20.9)s 10 | the second time closing breaker is still failure, the module will send out closing breaker failure signal. When the breaker fail to open for the first time, the module will close breaker, and then attempt Again open to open for the second time, if 10 |i (0-20. . time (020.08 ‘0 Tthe second time opening breaker is still failure, the module will send out opening breaker failure signal, Itis the delay from #1 power is GENS start por 14 | Gelay (0-9999)s 1 [abnormal to send out start generator signal. GENS stop Itis the delay from #1 power is 12 | delay (0-9999)S 5 normal to send out stop generator signal. 13_| Cycle run time | (1-1440)m__| 720 | Gens cycle run time. Cycle shutdown + le "| (4-1440)m 720. | Gens cycle stop time. 15 | Rated volt (100-600)V_[ 230 _| AC system rated voltage The settings are used to configure the power over 16 | Over volt (100-150)% | 120 | voltage point in the event of the voltage rising above the setting value. This value canbe BS66 Series ATS CONTROLLER 1SSUE2010-07-05 Version 1.4 Page 11 of 23 BS88/BS88-LN ATS CONTROL MODULE [Num [Wem [Range —[Defauit |Description] adjusted suit user requirements. Normal return value of over 17 | Return over vot} (100-180)% | 118 | Noone, The settings are used to configure the power under 48 | Under volt (60-100)% | 80 | voltage point in the event of the voltage falling below the setting value. Return under ; Normal return value of under 19 | vott (60-100)% | 85 | voltage. When the frequency of power 20 | Over Freq (0.0-75.0)Hz | 55.0 | is over than the point, over frequency is active. Reiumn over Normal return value of over 21 | eg (0.0-75.0)H2 | 52.0 | peauency. When the frequency of power 22 | Under Freq | (0.0-75.0)Hz| 45.0 | is low than the point, low frequency is active. Return under Normal return value of over 23 | reg (0.0-75.0)H2| 48.0 | fer enoy 24 | CT rate (660005 | _500__| Current Transformer rate. Rated load 5 ee (6-500) 500 | Load rated current. 26 | Over Current | (499.450)% | 120 | Load over current value. value 2 eon (0-8999)s | 1296 | Over current alarm delay value. Equipment 28 tl ines (1-284) 1 | RS485 communication address 23 _| Password 1234_| it applies to modify parameters, 1.1# Mains 2# Gens System type 2.1# Gens 2# Mains 30 1-4) 1 select i 3.1# Mains 2# Mains | 4.4# Gens 2# Gens 1. Two Breaking, two OFF position, such as the ATS composed of two circuit Breaking breakers or two contacts. ot an oul (1-3) 1/2 One Breaking, one OFF Position (three segments kind), such as SOCOMEC VE switch. 3. NO Breaking, no OFF position (two segments kind), S88 Series ATS CONTROLLER ISSUE2010-07-05 Version 1.4 Page 12.0f 25. BS88/BS88-LN ATS CONTROL MODULE such as SOCOMEC VS switch. Select AC 32 system (1-4) 1. 3-phase 4 wire 2, S-phase 3 wire 3. Single phase 2 wire 4, 2-phase 3 wire 33. | Set Priority (1-3) 1. 1# Priority, setting #1 power transfer is prior. If #1 and #2 is normal at the same time, the switch will transfer load to #1 power source. 2. 2# Priority, setting #2 power transfers is prior. If #1 and #2 is normal at the same time, the switch will transfer load to #2 power source. 3. NO Priority, if #1, 2 sources is normal at the same time and #1, 2 take no load, the switch will first transfer load to #1 power source. Only when #1 power is abnormal, the #2 power will supply for load; if the switch have been taken load, it will not switched to another power until abnormality occurs in the power. 34 | Aux. output 1 (1-28) 25. 35_| Aux. output 2 (1-28) 28 36_| Aux. output 3 (1-28) 13 37_| Aux. output 4 (1-28) 16 38. | Aux. output 5 (1-28) 18 [Link] used [Link] failure output [Link] of transfer 04. Warning alarm output 05. Alarm output (delay) 06. 1# Volts normal 07.1# Volts abnormal 08.2# Volts normal 09.2# Volts abnormal [Link] current output 11. Auto state output 12. Manual state output 13. Gens start output(N/O) 14. Gens start output(N/C) 16.1# switch shutdown output 16. 1# switch break off output 17.2# switch shutdown output 18. 2# switch break off output BS86 Series ATS CONTROLLER 1SSUE2010-07-05 Version 1.4 Page 13 of 23 BS88/ BS88-LN ATS CONTROL MODULE 19. Common alarm output 20. Timing test Gen set 21.1# shutdown state 22.2# shutdown state 23.1#Gens start output 24.2#Gens start output [Link] power L1 [Link] power L2 [Link] power L3 [Link] power N 39_| Aux. input 1 (1-9) 02 | [Link] used 40_| Aux. input 2 (1-9) 01 __| [Link] compulsorily 41_[ Aux. input 3 (1-9) 01 _| [Link] off-load a [Link] on-load 05. Test Lamp i 06. 1# Gens Alarm 42_| Aux. input 4 (1-9) Of | G7 2#Gené Alarm 08. Remote start genset input 09. Reserved 7.2. INPUT/OUTPUT FUNCTION DESCRIPTION The input port function describes: tem Description 1 Not used Invalid 2 Breaking compulsorily ‘When active, this will force the breaker to transfer the ATS to OFF position. It isn't suit for none OFF position ATS. 3 Test off-load When active, this will send out a start generator signal immediately. After 2# source is normal, if 1# source is normal, the breaker will not act. The breaker will transfer the load to 2# only when 1# source is abnormal. After 1# source restore normal, the breaker will transfer the load to 1#. Here the start generator signal output will keep. 4 Test On-Load When active, this will send out a start generator signal immediately. After 2# source is normal, the breaker will transfer the load to 2# immediately regardless of 4# source normal whether or not. 5 Test LED When active, all Led lamps mounted on the front panel will illuminate, LCD will fill black block. 6 1# Gens Alarm In Cycle start, if the input is active, 1 # Gens will not BS88 Series ATS CONTROLLER ISSUE2010-07-05 Version 14 Page 14 of 23 BS88/BS88-LN_ATS CONTROL MODULE start 7 2 Gens Alarm In Cycle start, if the input is active, 2 # Gens will not start 8 Remote start input | This input is necessary for oycle start generator. ‘9 Reserved The output function describes: tem Description 1 Not used Critical fault alarm including switch transform 2 Critical failure output failure, | Switch failed including 1# closed failure,1# open eee failure, 2# closed failure, 2# open failure. General warming includes 1# reverse phase 4 Warning alarm output | sequence; 2# reverse phase sequence, and load ‘over current and compulsory breaks. i itput 60 5 Alarm output (delay) Serious fault alarm output, continuous outpu seconds. 6 1# Volts normal twill output when #1 voltage is normal. 7 4# Volts abnormal Itwill output when #1 voltage is abnormal. 8 2# Volts normal It will output when #2 voltages is normal. 9 2# Volts abnormal twill output when #2 voltages is abnormal. 10 Over current output __| Set limits on more load current and exceeds delay. 11 Auto state output In auto state output. 12 Manual state output__| In manual state output. 13Gens start output(N/O) _| When generator starts output (Relay closed). 14Gens start output (N/C)_| When generator starts output (Relay released). 15 1# switch shut output _| #1 Switch close output. 16 1# switch break off pe #1 Switch open output. 17 2# switch shut output | #2 Switch close output. 18 2# switch break off pei #2 Switch open output. 19 Common alarm output _| It is include serious fault alarm and common alarm. 20 Timing test Gen set Schedulers start generator function. 21 1# shut state #1 Switch auxiliary close output. 22 2# shut state #2 Switch auxiliary close output. 23 1#Gens start output 4# Gens start output. 24 2#Gens start output 2# Gens start output. 25 ATS power L1 26 ATS power L2 27 ATS power L3 28 ATS power N ATS power supply. BS88 Series ATS CONTROLLER ISSUE2010-07-05 Version 1.4 Page 15 of 23 BS88/BS88-LN _ATS CONTROL MODULE 8 TIMING START GENERATOR On the main screen press ® key and select 2 Time start, and then pressing @) key, the screen will show the time start interface as follow: Time start cycle: Include inhibit start; single time, weekly or monthly. Load set: Starting generator with load or without load. Start time: Generator start date and time. Continue time: Generator continuously run time can be set on the duration of maximum time for 99 hours 59 minutes. 9 DATE AND TIME SETTING On the main screen press @) key and select 3 Date & Time set, and then pressing ® key, the screen will show the Date & Time Set interface as follow: Press ©) key according to the corresponding bit input values 0-9, pressing ® key to carry through the right of bit shift, right shift to the end of pressing ©) key, according to the key @) on the date and time can be updated controller. Date and time format set: year-month-date (week) and hour: minute. 10CONTROLLER INFORMATION On the main screen press ®) key and select 5 Controller information, and then pressing ® key, the screen will show the controller information interface as follow: Display content includes off positions setting and switching priority choice and controller version, date. Pressing @ key will exit and retum to main screen, 8888 Series ATS CONTROLLER —ISSUE2010-07-05 Version 14 Page 10 of 23 BS88/BS88-LN ATS CONTROL MODULE 11 ATS OPERATION 11.1 MANUAL OPERATION Press ® key and manual operation indicator light, the controller in manual mode. « Press @ key, 1# close relay outputs immediately, begin to monitor 1# closing input, if active, the 1# source LED light, the 1# source connect to load. © Press @ key, 2# close relay outputs immediately, begin to monitor 2# closing input, if active, the 2# source LED light, the 2# source connect to load. © Press © key and 4# or 2# open relay outputs immediately, begin to monitor 1# or 2# closing input, if inactive, the 1# and 2# source LED extinguish, and 1# and 2# source disconnect with load. "1: For the ATS of no OFF position, press © key is invalid. 11.2 AUTOMATIC OPERATION Press the @ key and the automatic LED light, enter AUTO mode and controller can automatically switch load to 1# or 24, 11.3 ATS POWER SUPPLY The power of ATS is supplied by controller, so long as one power is normal, this can guarantee ATS voltage power supply normally and can be transferred normally. Users should select power supply voltage (phase voltage or line voltage) based on ATS type. If power supplied by phase voltage, connect the phase A1 to Pin5 in AUX. output and A2 to Pin7, and connect the phase N1 to Pin8 in AUX. output2 and N2 to Pin10, then connect the common output of AUX. outputt&2 to ATS power supplies. Then controller power on, enter parameters setting menu, and set the AUX output! as "ATS power L1”. If the ATS power supplied by Line voltage, set as ‘same as above, and only need to change phase N to phase B. Wiring diagrams are 5S86 Series ATS CONTROLLER _ISSUE2010-07-08 Version 14 Page 17 of 23 BS88/ BS88-LN ATS CONTROL MODULE shown as following: z zi g 2 & fi f 3 2 3 2 3 2 8 AI @ A2 Nig na AIO AD Bi Bz 8] 1 8] 9} 10) 8) 1 4 9} 10} Ld d ‘Aux x ourrtrs ourpurz outers ourrura (168) (186A) (164) (164) ATSPOWERL1 ATS POWERN ATSPOWERL1 —ATSPOWERL2 ATS L-N voltage power supply ATS L-L voltage power supply Note: Normal Closed input voltage must come from the same one circuit voltage. 12 COMMUNICATION CONFIGURATION BS88 series has RS485 serial port, be allowed to connect the local area network with open structure. Its apply protocols of ModBus communication with PC or data acquisition system running on software. Also can provide a simple and practical to factories, telecom, industrial and civil buildings dual power switching management plan, achieve dual power monitor and “remote controlling, remote measuring, remote communication” functions. More information of Communication Protocol, see the “BS88 communication protocol”. Communication parameters, Module address 1 (range: 1-254, User can set it) Baud rate 9600 bps Data bit Bbit Parity bit None Stop bit 1 bit or 2-bits(set via PC) BS86 Series ATS CONTROLLER —ISSUE2010-07-05 Version 14 Page 18 of 23 BS88/ BS88-LN ATS CONTROL MODULE 13DESCRIPTION OF CONNECTING TERMINAL ISIC OMOIOIOIOIOIG Oloiois + | s# closed output | Passive relay contact | ateg 250168 2 output 3 Passive relay contact 4] 2 losed output | Pa Rated 250V16A 5 NC The default is | Free voltage relay 6 | Aux. output1 [Common _| ATS power of | contracts ia NO U1 output. Rated 250V16A, 8 NC The default is | Free voltage relay 9 | Aux. output 2 Common | ATS power of | contracts 10 NO Li output. _| Rated 250V16A 1 At voltage input 1# AC 3phase 4 wire If the input for single-phase, only connect A1, N14 voltage input [42 [et 13 [Ct 14 [NA 15 [Az 16 | B2 17 [¢2 18 N2 2# AC 3-phase 4 wire If the input for single-phase, only connect A2, N2 BS86 Series ATS CONTROLLER ISSUE2010-07-05 Version 1.4 Page 19 of 23 BS88/BS88-LN ATS CONTROL MODULE connect the generator fii SND battery negative pole DC negative input When you need to start generator, connect the terminal to the generator battery positive pole Detection of 1 # switch 21 1# closed input closing state, voltage free | It is active to GND contact input Detection of 2 # switch 22 2# closed input closing state, voltage free | It is active to GND contact input DC positive input 8-35V controller power supply 20 | DC power input 23 | Aux. input 1 24 | Aux. input 2 25 | Aux. input 3 26 | Aux. input 4 Itis active to GND 27 Voltage free relay contacts 38 | Aux. output 3 algal Rated 250V7A 29 Voltage free relay contacts 30 | Aux. output 4 Lait Rated 250V7A 31 Voltage free relay contacts 39 | Aux. output 5 cat Rated 250V7A 33 | RS485 A+ Sart pease ae RS485 communications por 35 | RS485 GND 36 | !Alinput Sensing from Secondary 37 1A Output phase A current 38 | IB Input Sensing from Secondary 39 [1B Output phase B current 40 | !C Input Sensing from Secondary 41 | 1C Output phase C current join tcp CONTR | LCD Display Adjust the LCD contrast AST LINK | Program port Factory update '5S86 Series ATS CONTROLLER 1SSUE2010-07-05 Version 1.4 Page 200125 BS88/BS8B-LN ATS CONTROL MODULE 14TYPICAL WIRING DIAGRAM ATYS3 Diagram (With Current) LOAD uN ‘1#voltage input, 2#tvoltage input Ri 5% Re st oe s2 TH ss 2 i ne Ni ATYSS i 7prspse[s14] 84 no 19} 36 | Close il Close 7 Break 1H lose inp ATS CONTROL MODULE Generator} icon 3 phase current input 2 position Manual Switch Diagram (63A to 630A, with Current) LOAD Mains input rater input Ro 82 n i [Generator CONTROL MooULE E t : BS88 Series ATS CONTROLLER —ISSUEZ010-07-05 Version 14 Page 21 of 3 BS88/BS8B-LN ATS CONTROL MODULE Contactor Diagram (With Current) LOAD uRBN 1@voltage input 2avoltage input RI st 1 Nt R2 82 12 Nz Eontactor Contactor & e405 fs 2 Aintse 5 37 5 eure 20} finns 5 3 (aad? j9}mnr- 8 Ficbu ATS CONTROL MODULE zege ATYSMSS Diagram LOAD bRoN 1#voltage input RI s1 1 Nt 2#voltage input R2 s2 12 N2 gtalal ATYSM3S | i715 313314] 14] 11 fro 7]r03] Gno 19] — 45 18 1 18 Close input 26 Close input 8 Iai ATS CONTROL MODULE 3 phase current input $ 2 Generator BS88 Series ATS CONTROLLER —ISSUE2010-07-05 Version 14 Page 22.01 23. BS88/ BS88-LN_ATS CONTROL MODULE 15INSTALLATION en | Vesen 16FAULT FINDING CUT OFF Controller no operation Check the Phase A1, N1 or Phase A1, N1 voltage. Check connection wirings from the controller to ATS. Check DC fuse. RS485 communication failure Check whether the RS485 is wrong connection between negative and positive. ‘Check whether the RS485 adapt is abnormal. Check whether the parameter settings in the module addresses are incorrect. If the above methods are no using, you can try to connect the GND of controller with RS485 GND (or PC GND). Recommend that the A and B lines of the 485 network should be terminated at each end with a 1200 resistor. LU Programmable output Check programmable output connections, pay attention {to Normally opened and closed. Peet |Check the output parameters settings. Ensure that the programmable input connect to GND! Programmable input | reliably when it’s active, and hung up when it is inactive. abnormal (Note: The input will be possibly destroyed when connected with voltage) ATS is not work while |Generator running Check ATS. Check the connection wirings between the controller and the ATS. Ensure that the ATS OFF position numbers are same as the setting OFF position numbers. BS88 Series ATS CONTROLLER ISSUE2010-07-05 Version 14 Page 23 of 23 zl 3 from i Matis SUPPLY oN 3 PI se Fh oe BRB not FSA wo | faye | | noma ale BR =o] | movers fa] | comer oO 2 > 4 e “4 2a NSA 3] 3 e|~/T 2° ELL 3) 5 i Eke a eel | ekeer 4 es 5 fa[s|Sner]| ~

You might also like