CYC RIDE CONTROL
App User Guide
support@[Link]
+852 3690 8938
© 2022 CYCMOTOR LTD
01 Introduction
CYC RIDE CONTROL
Monitor & customize your e-bike riding experience for all CYCMOTOR mid-drive systems. Use it as a
secondary dashboard, settings set-up, or both. Unleash all the possibilities of e-bike customization at your
fingertips.
The mobile app is not the only way to customize your system. The controller is also programmable via the
included display- integrated for your convenience.
This platform is your go-to-station for your CYCMOTOR kit & X6/X12 controllers.
FEATURES
• Bluetooth connectivity
• Complete with torque sensor configuration
• Compatible with X6 & X12 controllers
• Real-time dashboard for all your motor & riding information
• Fully customizable parameters for pedal assist, throttle & gear preferences
© 2022 CYCMOTOR LTD
02 Dashboard
DASHBOARD
Warning icon to check error codes
Brake sensor indicator COMING SOON & clear faults
Bluetooth icon to connect
to your device
Instantly change between STREET
& RACE mode
Change between your
DASHBOARD & SETTINGS page
Serial number connected
to controller
ALL PARAMETERS SHOW
REAL-TIME INFORMATION
© 2022 CYCMOTOR LTD
03 Connecting a Device
CONNECTING A DEVICE
STEP #1:
Open the app and tap the Search button at the
bottom of the screen. Kindly ensure your
phone’s Bluetooth is enabled. (Please keep
close to the motor while connecting)
STEP #2:
Available devices will then be listed, select
your kit and it will begin connecting to the
controller. (Please note signal strength)
STEP #3:
Once connected, the CONNECT icon will
change stating you are connected & can select
again to disconnect.
© 2022 CYCMOTOR LTD
04 Main Settings
MAIN SETTINGS
The settings page allows you to navigate
through different parameter categories. There
are six different categories with each providing
a set of adjustable parameters or readings
from your ebike system.
IMPORTANT
Save all new changes in parameters to flash or
risk losing progress. Any changes made that
were not saved will be lost after a restart. Note
to save after every change in value.
To save to flash, tap the ‘Save’ button in the
upper righthand corner, ‘Save successful’
message will appear upon completion.
© 2022 CYCMOTOR LTD
05 General
GENERAL
TEMPERATURE UNIT
Set your units to display in degrees Celsius (°C)
or Fahrenheit (°F)
SPEED UNIT
Set the speed unit to miles or kilometers.
MOTOR DIRECTION
This setting is for users who’d want to switch
the direction to where the motor is facing.
Note that this is reserved for specific uses only.
WARNING: Do not change this setting if using
the motor in its default position. Contact CYC
for assistance.
RESTORE DEFAULT SETTINGS
Restore to factory/default settings.
© 2022 CYCMOTOR LTD
06 Modes & Levels
MODES & LEVELS
RACE & STREET MODE
You can set the throttle & PAS output
independently for both modes.
RACE MODE THROTTLE & PAS
Race Mode is your “boost” or “full power” mode
and has parameters set for reaching closer to
the system’s full capabilities. You can adjust
these to your own preference within the
capabilities of your controller. The default
setting in Race Mode is 3000W & 100 km/hr.
STREET MODE THROTTLE & PAS
Street Mode is intended to be set to your
region’s legal limits. You can adjust these to
your own preference or to your region’s legal
limits. You can adjust these to your own
preference or to your region’s legal limits. The
default setting in Street Mode is 750W &
25Km/hr.
© 2022 CYCMOTOR LTD
07 Throttle
THROTTLE
RAMPING TIME
This is the time it takes for the motor to
achieve the required input. For example, if you
open the throttle fully, it will take 250ms (by
default) before the motor gives you full power.
It will gradually ramp up to full power within
the set time. We recommend not to set this
below 150ms.
INPUT DEADBAND
This value pertains to opening the throttle
when it’s completely closed. This is the amount
of throttle can be moved from the zero
position without generating a response from
the motor. If this value is set lower, your
throttle will engage quicker and vice versa.
MAX VOLTAGE
This value should be the same as the Throttle
Voltage Reading when the throttle is closed
and sets the output when it is not active.
MIN VOLTAGE
This is the output of the throttle when opened
fully and is pre-set when purchased. This does
not need any change with CYC supplied
throttles.
THROTTLE AUTO SETUP
If you’d like to use your own throttle, this will
automatically setup the minimum and
maximum voltage accordingly. Follow the
steps as prompted on the screen.
© 2022 CYCMOTOR LTD
08 Pedal Assist
PEDAL ASSIST
PEDAL ASSIST SENSOR
Enabling pedal assist.
TORQUE SENSOR SENSITIVITY
This value pertains to activating pedal assist
when it’s completely off. This is the amount of
pedal force required to activate the pedal
assist. If this value is set higher, your pedal
assist will engage with less force and vice
versa.
POWER RAMP TIME
The amount of time it takes to reach the
desired input. This is the responsiveness of the
motor.
MOTOR ASSIST FACTOR
This value pertains to how hard you need to
pedal to get full power.
STATIC ENGAGE
This feature allows for a cadence-free pull
away. i.e., only torque (40N.m.) is required to
activate pedal assist.
Pedal Backwards Cutoff
This features all you to cut the motor power
when you pedal backwards.
© 2022 CYCMOTOR LTD
09 Peripherals Setup
PERIPHERALS SETUP
SPEED SENSOR
Wheel Diameter
The wheel diameter can be measured or
calculated. We advise that this number must
be calibrated so that vehicle speed within the
app matches display speed. This will give more
accurate speed liming under different modes.
Remember to set the correct wheel size within
the display as well (only applicable to 500c &
750c displays). Kindly refer to your user
manual.
Wheel Magnet
This is the number of magnets in the wheel
that is communicating with the speed sensor.
For more accurate vehicle speed limiting and
measurement, we advise to add more
magnets to the wheel.
BRAKE SENSOR
Brake Sensor Enable
Enable/Disable brake sensors
BRAKE SENSOR SIGNAL INVERT TAB
If you are using brake sensors from a different
supplier, you can use this feature to set up your
brake sensors as needed.
MOTOR TEMP
This is an advanced feature and requires a
password from CYC to change. This allows you
to disable your motor temperature sensor.
Contact technical_support@[Link] for
more details.
© 2022 CYCMOTOR LTD
09 Battery
BATTERY
SERIES OF CELLS
10s = 36V, 14s = 52V, 20s = 72V
MAXIMUM VOLTAGE
The value the controller will fault when
connecting too high a voltage to the system.
An error will be triggered if a battery is too
high of a voltage.
MINIMUM VOLTAGE
The value the controller will fault when
connecting too low a voltage to the system.
This setting can be used to protect your
battery if too much voltage sag is detected.
© 2022 CYCMOTOR LTD
09 Battery
DISCLAIMER
If you require any more information or have any questions about the user manual disclaimer, please contact
us via email at technical_support@[Link].
All information contained in this user’s guide is published in good faith and for general informational
purposes only. CYCMOTOR LTD does not make any warranties about the completeness of this information
and encourages further inquiries as stated above if needed. CYCMOTOR LTD will not be held liable for any
losses and/or damages caused by negligence or misinterpretation.
PRIVACY POLICY
This service is provided by CYCMOTOR LTD. at no cost and is intended for use. This text is used to inform
visitors regarding our policies with the collection, use, and disclosure of personal information if anyone
decided to use this service. If you choose to use this service, then you agree to the collection and use of
information in relation to this policy. The personal information that we collect is used for providing and
improving the service. We will not share your information with anyone except as described in this Privacy
Policy. The terms used in this Privacy Policy have the same meanings as in our Terms and Conditions, which
is accessible at CYCMOTOR LTD unless otherwise defined in this Privacy Policy.
Information Collection and Use
For a better experience while using this service, we may require you to provide us with certain personally
identifiable information, including but not limited to Name (optional), Phone number, Email address,
Location (Optional). The information that we request will be retained by us and used as described in this
Privacy Policy.
Visit [Link]/privacy-policy for more detailed information.
© 2022 CYCMOTOR LTD
