WEST CELEBES COLLEGE OF TECHNOLOGY, INC.

Technical-Vocational Department
Aurelio F. Freires Sr., Lebak, Sultan Kudarat

TRAINING PLAN
ELECTRONIC PRODUCTS AND ASSEMBLY SERVICING NC II

Course: Electronic Products and Assembly Servicing NC II

Unit of Competency: Assemble Electronic Products
Module Title: Assembling Electronic Products
Modality: Check which modality will be applied. Multi-media is allowed

 Blended online
 Combination
 Modular
Learning Outcomes Contents Learning Resources
LO1. Prepare to assemble ❑ OHS Policies and Students/trainees must be
electronic products Procedures provided with the following:
❑ Philippine Electronics ❑ Learning Station
Code ❑ OHS manuals
❑ Mensuration/Mathematics ❑ PEC
Conversion of Units ❑ Tools and equipment
Applied Mathematics ❑ CBLM/Relevant
❑ Environmental Safety Instructional Materials
 Work Safety ❑ Video Clips
requirements and ❑ Power point presentation
economy of materials
with durability
 Knowledge in 5S
application and
observation of
required timeframe
 Knowledge of proper
handling and disposal
of chemicals
 Safety handling of
hand tools
 Practicing 3Rs –
reduce, re-use,
recycle/recover
 Managing waste from
electrical and
electronic equipment
(WEEE)
❑ Materials, tools and
equipment uses and
specifications
 Identification of hand
and power tools
 Proper care and use
of tools
LO2. Prepare/make pcb ❑ PCB Theory and Students/trainees must be
modules Characteristics provided with the following:
❑ PCB Problems and ❑ Variable power supply
Solutions ❑ Variable transformer

TP-EPAS-NC2-WCCTI
 WEST CELEBES COLLEGE OF TECHNOLOGY, INC.
Technical-Vocational Department
Aurelio F. Freires Sr., Lebak, Sultan Kudarat

❑ PCB Manufacturing ❑ Soldering iron

 PCB Manufacturing ❑ Hot air soldering station
Information ❑ Table top reflow oven
 PCB Layout and ❑ Desoldering tools
Artwork ❑ Screwdriver (assorted)
❑ PCB Fabrication ❑ Wrenches (assorted)
 Blanking, Cutting, ❑ Allen wrench/key
Punching, Drilling ❑ Function/Signal
 Laminating generator
Techniques ❑ Multi-testers
 Plating, Etching, analog/digital)
Surface Finishing ❑ Utility knife/striper
❑ Coatings ❑ Pliers(assorted)
❑ Surface Mount ESD free workbench with
Components and Devices mirror
❑ Through-Hole Mount ❑ Oscilloscope, digital
Components and Devices ❑ High-grade magnifying
❑ Design Compliance with glass with lamp
EMI / EMC ❑ Flashlight/headlamp
❑ Component Layout and ❑ Cleaning brush
Grounding ❑ Soldering wire
❑ Thermal and Vibration ❑ SMD soldering paste
Theories ❑ Stranded/solid/h ok-up
❑ Environmental Control wires
❑ Assorted
Electronic
Components
❑ Working Area/Bench
Learning materials
❑ Books and References
❑ Technical manuals
❑ Documentation forms
❑ Report forms
❑ CBLM
LO3. Mount and solder ❑ Soldering Characteristics Students/trainees must be
electronic components ❑ Soldering Principles provided with the following:
❑ Fundamentals of ❑ Function/Signal
Soldering and generator
Desoldering ❑ Utility knife/striper
❑ Fundamentals of ❑ Pliers(assorted)
Soldering Equipment, ❑ ESD-free workbench
Tools and Materials with mirror
❑ Mounting of Components ❑ Oscilloscope, digital
❑ Soldering/Desoldering ❑ High-grade magnifying
Techniques/Procedures glass with lamp
❑ Connectors and ❑ Flashlight/headlamp
Terminators ❑ Cleaning brush
❑ Soldering wire
❑ SMD soldering paste
❑ Stranded/solid/h ok-up

TP-EPAS-NC2-WCCTI
 WEST CELEBES COLLEGE OF TECHNOLOGY, INC.
Technical-Vocational Department
Aurelio F. Freires Sr., Lebak, Sultan Kudarat

wires
❑ WorkingArea/Bench
❑ Learning materials
❑ Books and References
❑ Technical manuals
❑ Report forms
❑ CBLM
LO4. Perform electronic ❑ Assembly Procedures Students/trainees must be
product assembly ❑ Soldering Technology provided with the following:
 Reflow Soldering ❑ Variable power supply
 Wave Soldering ❑ Variable transformer
❑ Soldering iron
 Hand Soldering
❑ Hot air soldering station
 RoHS and Lead-Free
❑ Table top reflow oven
Soldering ❑ Desoldering tools
❑ Non-Solder Connections ❑ Screwdriver (assorted)
(terminal block) ❑ Wrenches (assorted)
 Cleaning ❑ Allen wrench/key
 Repair and Rework ❑ Function/Signal
 Safety generator
❑ Multi-testers
 ESD protection
(analog/digital)
❑ 3Rs Waste Management ❑ Utility knife/striper
Programs ❑ Pliers (assorted)
❑ WEEE Directives ❑ ESD-free work bench
with mirror
❑ Oscilloscope, digital
❑ High-grade magnifying
glass with lamp
❑ Flashlight/headlamp
❑ Soldering wire
❑ SMD soldering paste
❑ Stranded/solid/h ok-up
wires
❑ Assorted electronic
components
❑ Working Area/Bench

LEARNING MATERIALS
❑ Books and References
❑ Technical manuals
❑ Documentation forms
❑ Report forms
LO5. Test and inspect ❑ Proper Care and Use of Students/trainees must be
assembled electronic Tools provided with the following:
products ❑ Principles of Electrical TOOLS
Circuits ❑ Long-nosed pliers
❑ Handling of ❑ Diagonal cutters
Electronic/Digital ❑ Standard screwdrivers
Components ❑ Soldering iron, 30w

TP-EPAS-NC2-WCCTI
 WEST CELEBES COLLEGE OF TECHNOLOGY, INC.
Technical-Vocational Department
Aurelio F. Freires Sr., Lebak, Sultan Kudarat

❑ Testing of Electronic ❑ De-soldering iron, 30w

Products ❑ Screw driver assorted,
❑ Housekeeping Phillips, slotted
Procedures ❑ Wrenches assorted
❑ Allen wrench/key
❑ Utility knife/stripper
❑ Pliers assorted, long
nose, Side cutter
❑ Test jig

FACILITIES
❑ Working area/bench
❑ Sufficient lighting and
ventilation system

LEARNING MATERIALS
❑ Books and references
❑ Technical manuals
❑ Report forms
❑ Self-paced learning
elements

MATERIALS
❑ Solder lead
❑ Cleaning brush
❑ Lead free solder
❑ Resinco resolder
❑ Wire stranded,# 2,
different colors)
❑ Silicon grease
❑ Resistors (different
values)
❑ Capacitors (different
values)
❑ Transformer

TP-EPAS-NC2-WCCTI
 WEST CELEBES COLLEGE OF TECHNOLOGY, INC.
Technical-Vocational Department
Aurelio F. Freires Sr., Lebak, Sultan Kudarat

TRAINING PLAN
ELECTRONIC PRODUCTS AND ASSEMBLY SERVICING NC II

Course: Electronic Products and Assembly Servicing NC II

Unit of Competency: Service Consumer Electronic Products and Systems
Module Title: Servicing consumer electronic products and systems
Modality: Check which modality will be applied. Multi-media is allowed

 Blended online
 Combination
 Modular
Learning Outcomes Contents Learning Resources
LO1. Prepare unit, tools ❑ Mensuration/Mathematics Students/trainees must be
and workplace for ❑ Drawing and Schematic provided with the following:
installation and service Diagram ❑ Learning elements and
❑ Environmental Safety manuals
❑ Hand and Power Tools ❑ Working area/bench
❑ Proper Care and Use of ❑ PPE
Tools ❑ Tools, equipment and
❑ Test and Measuring test instruments
Instruments ❑ Needed audio-video
❑ Care and use of Test and products and systems
Measuring instrument ❑ Needed consumer
❑ Audio-Video Products and appliances
Systems ❑ Service
❑ Domestic Electronic manuals/schematics
Appliances ❑ ESD free working
❑ Principles Of Electrical area/bench
Circuits ❑ Needed electronic
❑ Fundamentals Of Direct spare parts/supplies
Current Circuits
❑ Fundamentals Of
Alternating Current Circuits
❑ Fundamentals Of Electronic
Components and Circuits
❑ Fundamentals Of Digital
Logics, Components &
Circuits
❑ Fundamentals Of
Microprocessor Circuits and
Programming
❑ Analysis Of Troubles and
Isolation Techniques
❑ Principles of Sound and
Acoustics
❑ Fundamentals of Audio
Amplifiers
❑ Fundamentals of Audio

TP-EPAS-NC2-WCCTI
 WEST CELEBES COLLEGE OF TECHNOLOGY, INC.
Technical-Vocational Department
Aurelio F. Freires Sr., Lebak, Sultan Kudarat

Source & Noise Reduction

System
❑ Fundamentals of AM & FM
Receivers
❑ Principles of Vision and
Color
❑ Fundamentals of Color
Television
❑ Fundamentals Of Video
Sources & Noise Reduction
System
❑ AM Transmission and
Reception
❑ FM Transmission and
Reception
❑ Analog TV Transmission
and Reception
❑ Digital HDTV Transmission
and Reception
❑ Audio Video Sources and
Formats
❑ Pulse Code Modulation
❑ Home Theater System
❑ Digital Noise Reduction
System
❑ CCTV System
Infrared Remote Control
System
❑ Motor And Motor Control
System
❑ LED And Lighting System
❑ Heat And Heating Control
System
❑ Solar Cell and Battery
Management System
❑ Microcontroller
❑ Microcontroller Interfacing
LO2. Install consumer ❑ Consumer Electronic Students/trainees must be
electronic products and Products and Systems provided with the following:
systems Installation Procedures ❑ Variable power supply
❑ Work safety requirements ❑ Variable transformer
❑ Application of 5S ❑ Soldering iron
❑ Audio / Video Products and ❑ Hot air soldering station
Systems ❑ Table top reflow oven
❑ Domestic Appliances ❑ Desoldering tools
Manual / Operating ❑ Screwdriver (assorted)
Instructions ❑ Wrenches (assorted)
❑ Hazardous and risk ❑ Allen wrench/key
assessment mechanisms ❑ Function generator
❑ Isolation procedures ❑ Multi-testers

TP-EPAS-NC2-WCCTI
 WEST CELEBES COLLEGE OF TECHNOLOGY, INC.
Technical-Vocational Department
Aurelio F. Freires Sr., Lebak, Sultan Kudarat

❑ Use of protective equipment (analog/digital)

and clothing ❑ Utility knife/stripper
❑ Use of codes of practice ❑ ESD-free work bench
❑ Philippine with mirror
electrical/electronic code ❑ Test jigs
❑ Waste Management ❑ Oscilloscope, digital
❑ High-grade magnifying
glass with lamp
❑ Flashlight/headlamp
❑ Cleaning brush
❑ Soldering wire
❑ SMD soldering paste
❑ Stranded/solid/hook-up
wires
❑ Assorted electronic
components

LO3. Diagnose faults and ❑ Systematic Pre-Testing Students/trainees must be

defects of consumer Procedure provided with the following:
electronic products and ❑ Troubleshooting Technique
systems ❑ Tools, equipment and
❑ System Defects/Fault
Symptoms test instruments
❑ Needed audio-video
❑ Mechanical and
products and systems
Electrical/Electronic Testing
❑ Needed consumer
❑ Company Policy/Procedures appliances
❑ Service
manuals/schematics
❑ ESD free working
area/bench
❑ Needed electronic
spare parts/supplies
❑ Service manuals
LO4. Maintain/Repair ❑ Consumer Electronic Students/trainees must be
consumer electronic Components provided with the following:
products ❑ Consumer Electronic ❑ Variable power supply
Products ❑ Step-down transformer
❑ Application of work safety ❑ Soldering iron/gun
practices and time ❑ Desoldering tools
management ❑ Screwdriver (assorted)
❑ Use and maintenance of ❑ Test jig
test instruments, tools, & ❑ ESD-free work bench
equipment with mirror
❑ Schematic diagram reading ❑ Oscilloscope
skills ❑ High-grade magnifying
❑ Troubleshooting, Repair and glass with lamp
maintenance of electronic ❑ Flashlight
products ❑ Ball peen hammer
❑ Analysis of troubles and ❑ Soldering lead
isolation techniques ❑ Wires
❑ Application of

TP-EPAS-NC2-WCCTI
 WEST CELEBES COLLEGE OF TECHNOLOGY, INC.
Technical-Vocational Department
Aurelio F. Freires Sr., Lebak, Sultan Kudarat

troubleshooting technique ❑ Assorted consumer

❑ Application of substitution electronic components
technique ❑ Working Area/Bench
❑ Soldering/desoldering and ❑ Wrenches (assorted)
wiring/cabling techniques ❑ Allen wrench/key
❑ Application of work safety ❑ Signal generator -
practices and time AF/RF
management ❑ Multi-testers
❑ Application of substitution (analog/digital)
technique Replacing ❑ Utility knife/stripper
Defective ❑ Pliers (assorted)
Parts/Components ❑ Cleaning brush
❑ 3Rs Waste Management ❑ High voltage probe
Program
LEARNING MATERIALS
❑ Books and References
❑ Technical manuals
❑ Documentation forms
❑ Report forms
❑ CBLM
Audio-Video products and
systems included but not
limited to the folowing:
❑ AM-FM radio receivers
❑ Audio cassette
recorders
❑ DVD/VCD player
❑ Television
❑ PC monitors
LO5. Re-assemble and ❑ Re-assembling Procedures Students/trainees must be
test repaired consumer ❑ Service provided with the following:
electronic product Documentations/Procedures ❑ Variable power supply
❑ Environmental ❑ Step-down transformer
Requirements ❑ Soldering iron/gun
❑ ECE Law ❑ Desoldering tools
❑ Commissioning Procedures ❑ Screwdriver (assorted)
❑ Wrenches (assorted)
❑ Allen wrench/key
❑ Signal generator
- AF/RF
❑ Multi-testers
(analog/digital)
❑ Utility knife/stripper
❑ Pliers (assorted)
❑ Test jig
❑ ESD-free work bench
with mirror
❑ Oscilloscope
❑ High-grade magnifying
glass with lamp

TP-EPAS-NC2-WCCTI
 WEST CELEBES COLLEGE OF TECHNOLOGY, INC.
Technical-Vocational Department
Aurelio F. Freires Sr., Lebak, Sultan Kudarat

❑ Flashlight
❑ Cleaning brush
❑ High voltage probe
❑ Ball peen hammer
❑ Soldering lead
❑ Wires
❑ Assorted consumer
electronic components
❑ Working Area/Bench

Learning materials
❑ Books and References
❑ Technical manuals
❑ Documentation forms
Report forms
❑ CBLM

Audio Video products and

systems included but not
limited to the following:

❑ AM-FM radio receivers

❑ Audio cassette
recorders
❑ DVD/VCD player
❑ Television
PC monitors

TP-EPAS-NC2-WCCTI
 WEST CELEBES COLLEGE OF TECHNOLOGY, INC.
Technical-Vocational Department
Aurelio F. Freires Sr., Lebak, Sultan Kudarat

TRAINING PLAN
ELECTRONIC PRODUCTS AND ASSEMBLY SERVICING NC II

Course: Electronic Products and Assembly Servicing NC II

Unit of Competency: Service Industrial Electronic Modules, Products
Module Title: Servicing Industrial Electronic Modules, Products
Modality: Check which modality will be applied. Multi-media is allowed
 Blended online
 Combination
 Modular
Learning Outcomes Contents Learning Resources
LO1. Prepare unit, tools ❑ Industrial Electronic Students/trainees must
and workplace for Components be provided with the
installation / servicing ❑ Industrial Electronic Product following:
 Control boards and ❑ Tools, equipment and
modules test instruments
 Motor controllers and ❑ Access to Industrial
drives electronic products
 Man-machine interface and systems and
 Sensors and input devices work environment,
 Actuators and output e.g.
devices  Control boards and
 Opto-electronics modules
equipment and devices  Motor controllers
 Data communication and drives
systems  Sensors and input
 Microcontroller-based devices
equipment  Actuators and output
❑ Materials, Tools/Instruments devices
& Equipment Uses and  Opto-electronics
Specifications equipment and
 Identification of hand and devices
power tools  Data communication
 Proper care and use of systems
tools  Microcontroller-
 Identification of test and based equipment
measuring instruments ❑ Service
 Proper care and use of manuals/schematics
test and measuring ❑ ESD free working
instruments area/bench
❑ Theories and Principles ❑ Complete electronic
 Differential Amplifiers spare parts/supplies
 Analog To Digital
Conversion

TP-EPAS-NC2-WCCTI
 WEST CELEBES COLLEGE OF TECHNOLOGY, INC.
Technical-Vocational Department
Aurelio F. Freires Sr., Lebak, Sultan Kudarat

 Digital To Analog
Conversion
 Solenoid Actuators
 Solid State Relay
 LED
 Light Sensor
 Lighting Control System
 Temperature Control
System
 Temperature Sensor
 Voltage And Current
Control System
 Voltage/Frequency And
Frequency Conversion
 Timers
 Time Control System
 Liquid Level Control
System
 Optical Sensor
 Fiber Optic Cable
 Fiber Optic Diode (Tx And
Rx)
 Optical And Touch Control
System
 Hall Sensor
 Encoder/ Decoder
 DC/ AC And Brushless
Motor
 Stepping And Servo Motor
 Pulse Width Modulation
 Rotation Control System
 Acoustic Control System
 Teaching Pendant
 Basic Robotic Principles
 Ultrasonic Sensor (Tx And
Rx)
 Ultrasonic Control System
 Infrared Sensor
 Motion Sensor
 Infrared Control System
 Strain Gage
 Pressure Sensor
 Pressure Control System
 Microcontroller
 Microcontroller Interfacing

LO2. Install industrial ❑ Consumer Electronic Students/trainees must

electronic Products and Systems be provided with the
modules/products/ systems Installation Procedures following:
❑ Industrial Electronic ❑ Variable power supply
Components ❑ Step-down
❑ Industrial Electronic transformer

TP-EPAS-NC2-WCCTI
 WEST CELEBES COLLEGE OF TECHNOLOGY, INC.
Technical-Vocational Department
Aurelio F. Freires Sr., Lebak, Sultan Kudarat

Products ❑ Soldering iron/gun

❑ Application of work safety ❑ Desoldering tools
practices and time ❑ Screwdriver
management (assorted)
❑ Use and maintenance of ❑ Wrenches (assorted)
test instruments, tools, & ❑ Allen wrench/key
equipment ❑ Test jig
❑ Schematic diagram reading ❑ ESD-free work bench
skills with mirror
❑ Troubleshooting, Repair and ❑ Oscilloscope
maintenance industrial ❑ High-grade
components magnifyingglass with
❑ Analysis of troubles and lamp
isolation techniques ❑ Flashlight
❑ Application of ❑ Cleaning brush
troubleshooting technique ❑ High voltage probe
❑ Application of substitution ❑ Ball peen hammer
technique ❑ Soldering lead
❑ Soldering/desoldering and ❑ Wires
wiring/cabling techniques ❑ Assorted industrial
❑ Application of work safety electronic
practices and time components
management
❑ Application of substitution Learning materials
technique ❑ Books and
❑ Waste Management References
❑ Technical manuals
❑ Documentation forms
❑ Report forms
❑ CBLM
❑ Signal generator
- AF/RF
❑ Multi-testers
(analog/digital)
❑ Utility knife/stripper
❑ Pliers (assorted)

Industrial electronic
products may include the
following:
❑ Control boards and
modules
❑ Motor controllers and
drives
❑ Sensors and input
devices
❑ Actuators and output
devices
❑ Opto-electronics
equipment and
devices

TP-EPAS-NC2-WCCTI
 WEST CELEBES COLLEGE OF TECHNOLOGY, INC.
Technical-Vocational Department
Aurelio F. Freires Sr., Lebak, Sultan Kudarat

❑ Data communication
systems
❑ Microcontroller-based
equipment
LO3. Diagnose faults and ❑ Systematic Pre-Testing Students/trainees must
defects of industrial Procedure be provided with the
electronic ❑ Troubleshooting Technique following:
modules/products/systems ❑ System Defects/Fault ❑ Tools, equipment and
Symptoms test instruments
❑ Mechanical and ❑ Needed audio-video
Electrical/Electronic Testing products and systems
❑ Company Policy/Procedures ❑ Needed consumer
appliances
❑ Service
manuals/schematics
❑ ESD free working
area/bench
❑ Needed electronic
spare parts/supplies
❑ Service manuals
LO4. Maintain/Repair ❑ Industrial Electronic Students/trainees must
industrial electronic Components be provided with the
products ❑ Industrial Electronic following:
Products ❑ Variable power supply
❑ Application of work safety ❑ Step-down
practices and time transformer
management ❑ Soldering iron/gun
❑ Use and maintenance of ❑ Desoldering tools
test instruments, tools, & ❑ Screwdriver
equipment (assorted)
❑ Schematic diagram reading ❑ Wrenches (assorted)
skills ❑ Allen wrench/key
❑ Troubleshooting, Repair and ❑ Signal generator -
maintenance of industrial AF/RF
components ❑ Multi-testers
❑ Analysis of troubles and (analog/digital)
isolation techniques ❑ Utility knife/stripper
❑ Application of ❑ Test jig
troubleshooting technique
❑ ESD-free work bench
❑ Application of substitution
technique with mirror
❑ Soldering/desoldering and ❑ Oscilloscope
wiring/cabling techniques ❑ High-grade
❑ Application of work safety magnifying glass with
practices and time lamp
management ❑ Flashlight
❑ Application of substitution
❑ Cleaning brush
technique
❑ Waste Management ❑ High voltage probe

Learning materials

TP-EPAS-NC2-WCCTI
 WEST CELEBES COLLEGE OF TECHNOLOGY, INC.
Technical-Vocational Department
Aurelio F. Freires Sr., Lebak, Sultan Kudarat

❑ Books and
References
❑ Technical manuals
❑ Documentation forms
❑ Report forms
❑ CBLM
❑
Industrial electronic
products may include the
following:
❑ Control boards and
modules
❑ Motor controllers and
drives
❑ Sensors and input
devices
❑ Actuators and output
devices
❑ Opto-electronics
equipment and
devices
❑ Data communication
systems
❑ Microcontroller-based
equipment
LO5. Reassemble and test ❑ Re-assembling Procedures Students/trainees must
repaired industrial ❑ Service be provided with the
electronic products Documentations/Procedures following:
❑ Environmental ❑ Tools, equipment and
Requirements test instruments
❑ ECE Law Commissioning ❑ Needed audio-video
Procedures products and systems
❑ Needed consumer
appliances
❑ Service
manuals/schematics
❑ ESD free working
area/bench
❑ Needed electronic
spare parts/supplies

TP-EPAS-NC2-WCCTI
 WEST CELEBES COLLEGE OF TECHNOLOGY, INC.
Technical-Vocational Department
Aurelio F. Freires Sr., Lebak, Sultan Kudarat

TP-EPAS-NC2-WCCTI