W1 - EXTERIOR WALL, RSI 2.

97
REQUIRED W/ HRV (TABLE 9.36.2.5.B)

RSI-VALU
THICKNESS
E
EXTERIOR AIR FILM - 0.03
12 VINYL SIDING - 0.11
8" FASCIA TO SPEC.
12
6 BUILDING PAPER - 0.00
6" GABLE SHADOW TRIM 6 OSB SHEATHING 9.50 0.09
TO SPEC.
2x6 WOOD FRAMING
NON-VENTED SOFFIT AT 24" O.C. FILLED
- 2.67
TO SPEC. WITH R-22 BATT
INSULATION
POLYETHYLENE SHEET - 0.00

GYSUM BOARD 12.70 0.08

T.O. WALLS INTERIOR AIR FILM - 0.12
ASSEMBLY EFFECTIVE
3.10
1'-0" 1'-0" 1'-0" 1'-0" RSI
HEIGHT FROM T.O. MAIN FLOOR TO ROOF PEAK = 26'-4 3/4"

HEIGHT FROM T.O. MAIN FLOOR TO MID POINT OF ROOF = 23'-1 3/4"

3648SL 8460SL 4848SL 6" WINDOW TRIM TO SPEC.

VINYL BOARD & BATTEN

TO SPEC.
STANDARD VINYL CORNER
TRIM TO SPEC. EXTERIOR WALL
VINYL SIDING TO SPEC. RSI
RATING DETAIL
1/4"=1'-0"

EXTERIOR WALL ASSEMBLY

T.O. SECOND FLOOR - VINYL SIDING TO SPEC.
- BUILDING PAPER
3
- 8" OSB SHEATHING
- 2"x6"STUDS @ 24"
O.C. W/ R-22 BATT
6" DOOR TRIM TO SPEC. INSULATION
1'-0" - 6 MIL POLY. SEALED
AT TOP AND BOTTOM
1
- 2" GYPSUM BOARD

VINYL BOARD AND

BATTEN TO SPEC.
8"x8" COLUMN FINISHED W/ 1'-0" 1'-0"
STONE TO SPEC.
6" TRIM TO SPEC. ROOF NOTES:
- HOUSE MAIN ROOF TO HAVE
36"x96"
HEEL HEIGHT OF 1'-2" TO HELP
ALLOW TRAY CEILING
6" TRIM TO SPEC.

3'-0" HIGH RAILING TO SPEC. ENTRANCE NOTES:

STONE TO SPEC. - FRONT STEPS TO HAVE 4 RISERS
@ HEIGHT OF 7 21" PER RISER
T.O. MAIN FLOOR WITH 6" THRESHOLD FOR TOTAL
HEIGHT OF 3'-0".

EXTERIOR FINISH NOTES:

- STONE ON FRONT = 20 SQFT
- STONE ON LEFT SIDE= 16 SQFT
- STONE OF RIGHT SIDE =16 SQFT
- STONE OF COLUMN = 26 SQFT
TOTAL STONE = 78 SQFT

FRONT ELEVATION
1 Scale: 1/4" = 1'-0"

ADDRESS: LEGAL: LOT: BLOCK PLAN

Note: ALL INTERIOR WALLS ARE TO BE
New Day Drafting LTD. JULY 02, 2024 12 232 2422 SYMBOL LEGEND:
4 ISSUED FOR REVIEW JUNE 28, 2024 CONSTRUCTED FROM 2x4 STUDS AT 16
Sunpreet Grewal SUNESTATE HOMES
3 REVISED LAYOUTS JUNE 21, 2024 O.C. UNLESS OTHERWISE NOTED ON F.D.
780-265-1042 227 28 STREET SW SQUARE FEET -FLOOR DRAIN S -SMOKE DETECTOR
DRAWINGS.
[email protected] 2 REVISED LAYOUTS JUNE 10, 2024 EDMONTON, AB MAIN: UPPER: BSMT: TOTAL: SCALE: DATE: PAGE:
www.newdaydrafting.com 1 PRELIMINARY LAYOUTS JUNE 02, 2024
996 1,154 902 2,150 1/4" = 1'-0" JUNE 28, 2024 1 OF 9
HRV -HRV VENT CD -CARBON MONOXIDE DETECTOR
REV: DESCRIPTION: DATE:
 12 12
ASPHALT SHINGLES TO SPEC.
6 6
8" FASCIA TO SPEC.
12
6
NON-VENTED SOFFIT
TO SPEC.

T.O. WALLS

1'-0" 1'-0" 1'-0"

STANDARD VINYL CORNER

TRIM TO SPEC.

VINYL SIDING TO SPEC.

8460SL 7260F

T.O. SECOND FLOOR

1'-0"

1'-0" 96"x96" SLIDING

PATIO DOOR

3'-0" HIGH RAILING 7272SL

TO SPEC.

CEMENT PARGING (NOT TO

EXTEND MORE THAN 1'-6"
T.O. MAIN FLOOR ABOVE FINISHED GRADE)

4848SL

REAR ELEVATION
1 Scale: 1/4" = 1'-0"

ADDRESS: LEGAL: LOT: BLOCK PLAN

Note: ALL INTERIOR WALLS ARE TO BE
New Day Drafting LTD. 02 12 232 2422 SYMBOL LEGEND:
4 ISSUED FOR REVIEW JUNE 28, 2024 CONSTRUCTED FROM 2x4 STUDS AT 16
Sunpreet Grewal SUNESTATE HOMES
3 REVISED LAYOUTS JUNE 21, 2024 O.C. UNLESS OTHERWISE NOTED ON F.D.
780-265-1042 227 28 STREET SW SQUARE FEET -FLOOR DRAIN S -SMOKE DETECTOR
DRAWINGS.
[email protected] 2 REVISED LAYOUTS JUNE 10, 2024 EDMONTON, AB MAIN: UPPER: BSMT: TOTAL: SCALE: DATE: PAGE:
www.newdaydrafting.com 1 PRELIMINARY LAYOUTS JUNE 02, 2024
996 1,154 902 2,150 1/4" = 1'-0" JULY 02, 2024 2 OF 9
HRV -HRV VENT CD -CARBON MONOXIDE DETECTOR
REV: DESCRIPTION: DATE:
 12 6" WINDOW TRIM TO SPEC,

6
ASPHALT SHINGLES TO SPEC.

12
8" FASCIA TO SPEC. 6
NON-VENTED SOFFIT
TO SPEC.

T.O. WALLS
1'-0" 1'-0" 1'-0" 1'-0"

1836A 2'-0"
STANDARD VINYL
CORNER TRIM
TO SPEC.
1'-0"
VINYL BOARD &
BATTEN TO SPEC.
VINYL SIDING (2'-0" RETURN TYP.)
TO SPEC.
12
6 1'-0"
T.O. SECOND FLOOR
12
1'-0" 1'-0" 4

4860SL

1'-0"

3'-0" HIGH RAILING

TO SPEC. 6" TRIM
TO SPEC.

T.O. MAIN
FLOOR 36"x80"
32"x80"

1'-4 1/2"
CEMENT PARGING (NOT TO 1'-4 21" BUCK DOWN FROM TOP 6" DOOR TRIM STONE TO SPEC.
EXTEND MORE THAN 1'-6" OF CONCRETE FOUNDATION WALL TO SPEC. (2'-0" RETURN
3636A ABOVE FINISHED GRADE) TYP.)

LEFT ELEVATION
1 Scale: 3/16" = 1'-0"

ADDRESS: LEGAL: LOT: BLOCK PLAN

Note: ALL INTERIOR WALLS ARE TO BE
New Day Drafting LTD. 02 12 232 2422 SYMBOL LEGEND:
4 ISSUED FOR REVIEW JUNE 28, 2024 CONSTRUCTED FROM 2x4 STUDS AT 16
Sunpreet Grewal SUNESTATE HOMES
3 REVISED LAYOUTS JUNE 21, 2024 O.C. UNLESS OTHERWISE NOTED ON F.D.
780-265-1042 227 28 STREET SW SQUARE FEET -FLOOR DRAIN S -SMOKE DETECTOR
DRAWINGS.
[email protected] 2 REVISED LAYOUTS JUNE 10, 2024 EDMONTON, AB MAIN: UPPER: BSMT: TOTAL: SCALE: DATE: PAGE:
www.newdaydrafting.com 1 PRELIMINARY LAYOUTS JUNE 02, 2024
996 1,154 902 2,150 3/16" = 1'-0" JULY 02, 2024 3 OF 9
HRV -HRV VENT CD -CARBON MONOXIDE DETECTOR
REV: DESCRIPTION: DATE:
 12
6
ASPHALT SHINGLES TO SPEC.

12
6 8" FASCIA TO SPEC.

NON-VENTED SOFFIT
TO SPEC.

T.O. WALLS
1'-0" 1'-0" 1'-0"

2'-0"
STANDARD VINYL
CORNER TRIM
VINYL BOARD & 1'-0" TO SPEC.
BATTEN TO SPEC.
(2'-0" RETURN TYP.)
VINYL SIDING
TO SPEC.

T.O. SECOND FLOOR

12
4 1'-0"

1'-0"

3'-0" HIGH RAILING

6" TRIM TO SPEC.
TO SPEC.

T.O. MAIN
FLOOR

STONE TO SPEC. CEMENT PARGING (NOT TO

(2'-0" RETURN EXTEND MORE THAN 1'-6"
TYP.) ABOVE FINISHED GRADE)

RIGHT ELEVATION
1 Scale: 3/16" = 1'-0"

ADDRESS: LEGAL: LOT: BLOCK PLAN

Note: ALL INTERIOR WALLS ARE TO BE
New Day Drafting LTD. 02 12 232 2422 SYMBOL LEGEND:
4 ISSUED FOR REVIEW JUNE 28, 2024 CONSTRUCTED FROM 2x4 STUDS AT 16
Sunpreet Grewal SUNESTATE HOMES
3 REVISED LAYOUTS JUNE 21, 2024 O.C. UNLESS OTHERWISE NOTED ON F.D.
780-265-1042 227 28 STREET SW SQUARE FEET -FLOOR DRAIN S -SMOKE DETECTOR
DRAWINGS.
[email protected] 2 REVISED LAYOUTS JUNE 10, 2024 EDMONTON, AB MAIN: UPPER: BSMT: TOTAL: SCALE: DATE: PAGE:
www.newdaydrafting.com 1 PRELIMINARY LAYOUTS JUNE 02, 2024
996 1,154 902 2,150 3/16" = 1'-0" JULY 02, 2024 4 OF 9
HRV -HRV VENT CD -CARBON MONOXIDE DETECTOR
REV: DESCRIPTION: DATE:
 70'-0"

41'-0" 29'-0"

22'-6" 12'-4" 6'-2"

12'-8 1/2" 10'-3 1/2" 6'-0"

6'-0"

96"x96 SLIDING PATIO DOOR

8 1/4" 2'-10"

2'-10"
MICROWAVE
COOKTOP & WALL RANGE
OVEN 2'-0" 4'-6" 22'-6"

16'-0"x8'-0" OVERHEAD DOOR

W8 48"x80"

6'-3 1/2"
DOUBLE DOOR

5'-6"x11'-10"

6'-2"
ENGINEER APPROVED

KITCHEN
7'-3"

BEAM - FLUSH MOUNTED

SPICE
32

3'-4"
11'-1"x11'-6"

32

"
2'-8"

9'-9"
"x8

x 80
S

"x
1'-0" 3'-11 1/2"

KITCHEN

80
14'-6"x10'-0"

13'-6"x10'-2"

32"
"
"
2'-8"
NOOK

1'-0"
DECK

WASHER
60"x36"
14'-6"

2'-4"
DISH
SHOWER

3'-6"

19'-6"x23'-0"/ 29'-6"
5'-3 1/2"

1'-7 1/2"
HRV
48"x80"

FLOOR
DRAIN
DOUBLE DOOR

19'-6"
(481 SQFT)
FRIDGE

32"
6'-0" W8

GARAGE
BATH

x80
W8
7'-3"

ROOM
30

"
S "x8
24'-0"

24'-0"
0"

10'-0"x10'-6"
22'-6" 9'-8" 4'-4"

8'-9 1/2"
S

4'-3 1/2"
ENGINEER APPROVED BEAM

DEN

11'-0"
- FLUSH MOUNTED 16R
DOWN

9'-9"
32" W9
16R UP x96
"
ENGINEER APPROVED

10"
11'-11"x13'-11"
4'-6"

FAMILY ROOM
11'-5 1/2" BEAM

3'-3 1/2"
3'-4"

2'-6"

1'-8"
9'-6"

3'-4" 2'-9 1/2" 3'-9 1/2" 32"

48"x60"
72"x72"

x80

2'-0"

2'-0"
30" 1'-8" 1'-9 1/2" "
x80

4'-9 1/2"
"
5'-0"

4'-6"

4'-6"
36
4'-0" ELECTRICAL W8

"x9

2'-6"

2'-6"
FIREPLACE 36"

6"
x80
"

7'-7" 2'-4" 3'-9" 4'-3" 18'-2" 4'-4"

14'-9" 9'-11" 1'-1" 1'-6 3/4" 1'-8 1/4" 4'-6"

6'-0" 33'-6" 8'-0" 22'-6"

70'-0"

MAIN FLOOR PLAN

1 Scale: 3/16" = 1'-0"

ADDRESS: LEGAL: LOT: BLOCK PLAN

Note: ALL INTERIOR WALLS ARE TO BE
New Day Drafting LTD. 02 12 232 2422 SYMBOL LEGEND:
4 ISSUED FOR REVIEW JUNE 28, 2024 CONSTRUCTED FROM 2x4 STUDS AT 16
Sunpreet Grewal SUNESTATE HOMES
3 REVISED LAYOUTS JUNE 21, 2024 O.C. UNLESS OTHERWISE NOTED ON F.D.
780-265-1042 227 28 STREET SW SQUARE FEET -FLOOR DRAIN S -SMOKE DETECTOR
DRAWINGS.
[email protected] 2 REVISED LAYOUTS JUNE 10, 2024 EDMONTON, AB MAIN: UPPER: BSMT: TOTAL: SCALE: DATE: PAGE:
www.newdaydrafting.com 1 PRELIMINARY LAYOUTS JUNE 02, 2024
996 1,154 902 2,150 3/16" = 1'-0" JULY 02, 2024 5 OF 9
HRV -HRV VENT CD -CARBON MONOXIDE DETECTOR
REV: DESCRIPTION: DATE:
 67'-0"

56'-8 1/2" 10'-3 1/2"

14'-10" 11'-5 1/2" 5'-9 1/2" 5'-10" 5'-3 1/2" 13'-6"

1'-6"

48"x48"
14" BENCH

3'-3"
DRYER
60"x36"
1'-6" WIDE & 1'-0" JACUZZI

5'-9"
60"x36"

9'-6"x5'-4"

6'-0"
6'-1"
DEEP TRAY CEILING

7'-0"
SHOWER
7'-3"

9'-6"x13'-0"
BEDROOM 2
W.I.C

7'-11"
WASHER
1'-6"

2'-9"
9'-6"x11'-2"

9'-6""x5'-6"
MASTER BEDROOM
1'-6"

10'-4"

LAUNDRY

7'-1"x5'-0"
28
ENSUITE
30
13'-6"x14'-0"

2 8"
W.I.C.
"x8
"x8

x80
0"
0

HATCH
14'-6"

"

ATTIC

"
4'-7"

SHELVES

4'-4"
4'-3"
HRV

3'-4"
84"x72"

2'-5"
W9 80"

6'-9"
x
W9 32"
S

84"x60"
32"
x80 32"
" x80
"
7'-3"

12'-6"x10'-0"
BEDROOM 1
8'-5 1/2" 5'-9 1/2" 7'-2 1/2" 3'-11" 10'-3 1/2" 3'-0" 10'-6"

3'-11 1/2"
24'-0"

24'-0"
14'-10" S 3'-0"

3'-8"
80"
32

13'-6"
"x8

x
1'-6"

32"
S

0"

1'-6"
30"

ROOM

5'-0"x5'-1"
BATH
10'-10" 9'-9" 16R x 80"

"
W.I.C.

x80
DOWN

BATHTUB

6'-9"
60"x34"

28"
4'-6"

5'-6"
13'-2"x10'-0"
3'-4"

3'-4"
HRV
1'-6"

BONUS
ROOM
OPEN TO

1'-6"
BELOW
9'-6"

3'-4" 2'-9 1/2" 3'-7 1/2" 18"x36"

72"x60"

2'-0"
4'-3 1/2"
1'-6" WIDE & 1'-0"
5'-0"

4'-6"
DEEP TRAY CEILING

36"x48"

2'-6"
1'-6"
4'-7 1/2" 4'-5 1/2"

14'-9" 9'-9" 10'-6" 9'-1" 5'-5" 10'-6"

7'-0" 35'-0" 25'-0"

67'-0"

SECOND FLOOR PLAN

1 Scale: 3/16" = 1'-0"

ADDRESS: LEGAL: LOT: BLOCK PLAN

Note: ALL INTERIOR WALLS ARE TO BE
New Day Drafting LTD. 02 12 232 2422 SYMBOL LEGEND:
4 ISSUED FOR REVIEW JUNE 28, 2024 CONSTRUCTED FROM 2x4 STUDS AT 16
Sunpreet Grewal SUNESTATE HOMES
3 REVISED LAYOUTS JUNE 21, 2024 O.C. UNLESS OTHERWISE NOTED ON F.D.
780-265-1042 227 28 STREET SW SQUARE FEET -FLOOR DRAIN S -SMOKE DETECTOR
DRAWINGS.
[email protected] 2 REVISED LAYOUTS JUNE 10, 2024 EDMONTON, AB MAIN: UPPER: BSMT: TOTAL: SCALE: DATE: PAGE:
www.newdaydrafting.com 1 PRELIMINARY LAYOUTS JUNE 02, 2024
996 1,154 902 2,150 3/16" = 1'-0" JULY 02, 2024 6 OF 9
HRV -HRV VENT CD -CARBON MONOXIDE DETECTOR
REV: DESCRIPTION: DATE:
 70'-0"

41'-0" 29'-0"

6'-2 1/2" 14'-4" 9'-10 1/2" 10'-7"

1'-7 1/2"
1'-0"

6'-2"
BEAM - DROP MOUNTED

BEAM - DROP MOUNTED

2'-0" 4'-6" 22'-6"

ENGINEER APPROVED

ENGINEER APPROVED
6'-3"

BEAM - DROP MOUNTED

ENGINEER APPROVED

13'-6"

13'-6"
2"x4" LOAD RADON
14'-6"

EXTRACTION

2'-4"
BEARING WALL
ON TOP OF ROUGH-IN
24"x8" CONCRETE PIPE
FOOTING

1'-10 1/2"
9'-0"

16'-3"

19'-6"
BUCK DOWN TO
6'-3"

SUIIT SITE
23'-2 3/4" 2'-0" 6" 2'-0" 19'-9 1/4"
24'-0"

24'-0"
2'-9"

11'-0"
1'-0"

16R UP

2'-8"
36"x36"

H.W.T.

2'-4 1/2"
7'-0"
4'-2"
BUCK DOWN TO
6'-0"

SUIT SITE

2'-6"

1'-7 1/2"
FURNACE
10'-6"
F.D.
9'-6"

3'-4" 2'-9 1/2" 3'-4" CD

4'-9 1/2"
48"x48"

HRV

4'-6"
SUMP
3'-6"

3'-6"
PANEL PIT

3'-6" 2'-6" 7'-6"

20'-7 1/2" 3'-5" 9'-5 1/2" 16'-7 1/2" 3'-1" 2'-9 1/2"

14'-6 1/2" 9'-10 1/2" 9'-1"

6'-0" 33'-6" 8'-0" 22'-6"

70'-0"

1'-4 21" BUCK DOWN FROM TOP

OF CONCRETE FOUNDATION WALL

FOUNDATION PLAN
1 Scale: 3/16" = 1'-0"

ADDRESS: LEGAL: LOT: BLOCK PLAN

Note: ALL INTERIOR WALLS ARE TO BE
New Day Drafting LTD. 02 12 232 2422 SYMBOL LEGEND:
4 ISSUED FOR REVIEW JUNE 28, 2024 CONSTRUCTED FROM 2x4 STUDS AT 16
Sunpreet Grewal SUNESTATE HOMES
3 REVISED LAYOUTS JUNE 21, 2024 O.C. UNLESS OTHERWISE NOTED ON F.D.
780-265-1042 227 28 STREET SW SQUARE FEET -FLOOR DRAIN S -SMOKE DETECTOR
DRAWINGS.
[email protected] 2 REVISED LAYOUTS JUNE 10, 2024 EDMONTON, AB MAIN: UPPER: BSMT: TOTAL: SCALE: DATE: PAGE:
www.newdaydrafting.com 1 PRELIMINARY LAYOUTS JUNE 02, 2024
996 1,154 902 2,150 3/16" = 1'-0" JULY 02, 2024 7 OF 9
HRV -HRV VENT CD -CARBON MONOXIDE DETECTOR
REV: DESCRIPTION: DATE:
 R1
12
6

12
6

1'-0"
1'-6" WIDE AND 1'-0"
HEIGHT FROM T.O. MAIN FLOOR TO ROOF PEAK = 26'-4 3/4"

T.O. WALLS DEEP TRAY CEILING

HEIGHT FROM T.O. MAIN FLOOR TO MID POINT OF ROOF = 23'-1 3/4"

1'-0" 1'-6" 1'-6" 1'-0"

MASTER
BEDROOM ENSUITE W.I.C. LAUNDRY W.I.C. BEDROOM 2 BEDROOM 1
9'-1"

W1 W9 W1

F2 F1
T.O. SECOND FLOOR
1'-0 1/2"

12
1'-0" 4
ENGINEER APPROVED BEAM
- FLUSH MOUNTED
BATH HALL
ENGINEER
NOOK KITCHEN ROOM WAY DEN APPROVED
1'-0"
ENGINEER APPROVED ENGINEER
9'-1"

BEAM BEAM (BOTTOM OF APPROVED

W1 W8 W8 W9 W5
BEAM TO MATCH BEAM
BOTTOM OF GARAGE
TRUSS)

10'-0"
GARAGE
F3
T.O. MAIN FLOOR
1'-0 1/2"

W3 W3

ENGINEER APPROVED ENGINEER APPROVED

F5

2'-5"
BEAM - DROP MOUNTED BEAM - DROP MOUNTED

TELEPOST ON TOP OF
CONCRETE PAD UNFINISHED W12
8'-8"
9'-0"

W12 BASEMENT

4'-8"
4" INCH WEEPING
TILE COVERED IN
GRAVEL SEE TYP.
DETAIL F4

T.O. FOOTING

BUILDING SECTION
1 Scale: 3/16" = 1'-0"

ADDRESS: LEGAL: LOT: BLOCK PLAN

Note: ALL INTERIOR WALLS ARE TO BE
New Day Drafting LTD. 02 12 232 2422 SYMBOL LEGEND:
4 ISSUED FOR REVIEW JUNE 28, 2024 CONSTRUCTED FROM 2x4 STUDS AT 16
Sunpreet Grewal SUNESTATE HOMES
3 REVISED LAYOUTS JUNE 21, 2024 O.C. UNLESS OTHERWISE NOTED ON F.D.
780-265-1042 227 28 STREET SW SQUARE FEET -FLOOR DRAIN S -SMOKE DETECTOR
DRAWINGS.
[email protected] 2 REVISED LAYOUTS JUNE 10, 2024 EDMONTON, AB MAIN: UPPER: BSMT: TOTAL: SCALE: DATE: PAGE:
www.newdaydrafting.com 1 PRELIMINARY LAYOUTS JUNE 02, 2024
996 1,154 902 2,150 3/16" = 1'-0" JULY 02, 2024 8 OF 9
HRV -HRV VENT CD -CARBON MONOXIDE DETECTOR
REV: DESCRIPTION: DATE:
 14'-6"

1'-0" 6'-3" 6'-3" 1'-0"

9" 9"
6"x6" POST ON TOP
OF SCREW PILE

4 1/2" 9 3/4"

3-PLY 2"x8" DIMENSIONAL

LUMBER WOOD BEAM

2"x8" DIMENSIONAL
LUMBER JOISTS @ 16" O.C.
10'-0"

8'-9 3/4"

DECK LAYOUT
1 SCALE: 3/8" = 1'-0" 36" HIGH RAILING TO SPEC.

1"x4" DIMENSIONAL LUMBER FOR

DECK FLOOR

2"x8" DIMENSIONAL LUMBER JOISTS

@ 16" O.C.

3-PLY 2"x8" WOOD BEAM

9" 5'-9" 5'-9" 9"

DECK SECTION DETAIL

2 SCALE: 3/8" = 1'-0"

ADDRESS: LEGAL: LOT: BLOCK PLAN

Note: ALL INTERIOR WALLS ARE TO BE
New Day Drafting LTD. 02 12 232 2422 SYMBOL LEGEND:
4 ISSUED FOR REVIEW JUNE 28, 2024 CONSTRUCTED FROM 2x4 STUDS AT 16
Sunpreet Grewal SUNESTATE HOMES
3 REVISED LAYOUTS JUNE 21, 2024 O.C. UNLESS OTHERWISE NOTED ON F.D.
780-265-1042 227 28 STREET SW SQUARE FEET -FLOOR DRAIN S -SMOKE DETECTOR
DRAWINGS.
[email protected] 2 REVISED LAYOUTS JUNE 10, 2024 EDMONTON, AB MAIN: UPPER: BSMT: TOTAL: SCALE: DATE: PAGE:
www.newdaydrafting.com 1 PRELIMINARY LAYOUTS JUNE 02, 2024
996 1,154 902 2,150 3/8" = 1'-0" JULY 02, 2024 9 OF 9
HRV -HRV VENT CD -CARBON MONOXIDE DETECTOR
REV: DESCRIPTION: DATE:
ABOVE GRADE WALLS ASSEMBLIES: MATERIAL BREAKDOWN:

ALL RSI VALUES ARE TAKEN FROM THE NATURAL

EXTERIOR WALL - EXTERIOR WALL TO RESOURCES CANADA WEBSITE PAGE: "CALCULATING
W1 - VINYL SIDING EXTERIOR WALL, RSI 2.97 W6 - EXTERIOR WALL TO GARAGE, RSI 2.97 EXTERIOR WALL TO F2 - CANTILEVER FLOOR ABOVE UNHEATED
VINYL SIDING REQUIRED W/ HRV (TABLE 9.36.2.5.B) GARAGE REQUIRED W/ HRV (TABLE 9.36.2.5.B) W2 - STUCCO EXTERIOR WALL, RSI 2.97
SPACE, RSI 5.02, REQUIRED W/HRV EFFECTIVE THERMAL RESISTANCE OF OPAQUE
W1 W5 GARAGE REQUIRED W/ HRV (TABLE 9.36.2.5.B) CANTILEVER FLOOR
W11 F2 (TABLE 9.36.2.6.A) ASSEMBLIES".
- VINYL SIDING THICKNESS
RSI/ mm RSI-VALUE - 1
2" GYPSUM BOARD THICKNESS
RSI/ mm RSI-VALUE
(mm) 1 5
- BUILDING PAPER 3
(mm)
- 8" ACRYLIC STUCCO THICKNESS
(mm)
RSI/ mm RSI-VALUE - 8" OSB SUB-FLOOR
THICKNESS
(mm)
RSI/ mm RSI-VALUE
EXTERIOR AIR FILM - 0.03 - 8" OSB SHEATHING EXTERIOR AIR FILM - 0.03 FINISH - CELLULOSE INSULATION TOTAL RSI VALUE OF
- 3 - 11- 78" ENGINEERED AIR FILM (HEAT FLOW
8" OSB SHEATHING - 2x6 WOOD STUDS @ 1
EXTERIOR AIR FILM - 0.03 - 0.16 8.89 WAS CALCULATED USING THE VALUE OF
VINYL SIDING - 0.11 GYSUM BOARD 12.7 0.0063 0.08 - 1 2" EXTRUDED JOISTS @ 19.2" O.C DOWNWARD)
- 2"x6"STUDS @ 24" 24" O.C.FILLED WITH STUCCO FINISH 3.175 0.0009 0.002 0.025 RSI/ mm FROM TABLE CM-1.
O.C. W/ R-22 BATT BUILDING PAPER - 0.00 OSB SHEATHING 9.525 0.0098 0.09 POLYSTYRENE WITH R41 BATT OSB FLOOR SHEATHING 15.875 .0098 0.16
R22 BATT EXTRUDED POLYSTYRENE - OSB THERMAL VALUE IS 0.0098 RSI/ mm,
INSULATION INSULATION 38.1 0.035 1.33 INSULATION B/N 11- 78" ENGINEERED JOIST
OSB SHEATHING 9.525 0.0098 0.09 INSULATION 2x6 WOOD STUDS AT 24" INSULATION (XPS) TAKEN FROM TABLE CM-1.
- 6 MIL POLY. SEALED O.C. FILLED WITH R-22 - 2.67 - FLUID APPLIED AIR & FLUID APPLIED AIR & JOISTS @ 19.2" O.C W/ R41 - 6.36
2x6 WOOD STUDS AT - 6 MIL POLY. VAPOUR - 0.00 BATT INSULATION - GYPSUM SHEATHING VALUE OF 0.0063 RSI/
AT TOP AND BOTTOM BATT INSULATION VAPOUR BARRIER VAPOUR BARRIER - 6 MIL POLY. VAPOUR
24" O.C. FILLED WITH - 2.67 BARRIER SEALED AT 6MIL POLYETHYLENE mm, TAKEN FROM CM-1.
- 3 CARRIER
8" OSB SHEATHING
1 R-22 BATT INSULATION POLYETHYLENE SHEET - 0.00 OSB SHEATHING 9.525 0.0098 0.09 - 0.00
- 2" GYPSUM BOARD TOP AND BOTTOM VAPOUR BARRIER - 11- 78" WOOD JOISTS @ 19.2" O.C. W/ R41
6MIL POLYETHYLENE 1 - 2"x6"STUDS @ 24" 2x6 WOOD STUDS @
- NON-VENTED SOFFIT
- 0.00 - 2" GYPSUM BOARD
GYSUM BOARD 12.7 0.0063 0.08
TO SPEC. SOFFIT - - BATT INSULATION RSI VALUE OF 4.61, TAKEN
VAPOUR BARRIER O.C. W/ R-20 BATT 24" O.C. FILLED WITH - 2.53
INTERIOR AIR FILM - 0.12 R-20 BATT INSULATION EXTERIOR AIR FILM - 0.03 FROM TABLE FL-7.
GYSUM BOARD 12.7 0.0063 0.08 INSULATION
ASSEMBLY EFFECTIVE RSI 3.07 6MIL POLYETHYLENE - 2"x8" DIMENSIONAL LUMBER JOISTS @ 24"
INTERIOR AIR FILM - 0.12 - 6 MIL POLY. SEALED - 0.00 ASSEMBLY EFFECTIVE RSI 6.71
VAPOUR BARRIER O.C. W/ R41 BATT INSULATION B/W JOISTS
AT TOP AND BOTTOM
ASSEMBLY EFFECTIVE RSI 3.10
EXTERIOR CANTILEVER GYSUM BOARD 12.7 0.0063 0.08 RSI VALUE OF 5.30, TAKEN FROM TABLE FL-3.
W7 - CANTILEVER EXTERIOR WALL - SIDING, - 1
2" GYPSUM
INTERIOR FLOOR - RSI RATING OF 0.22 FOR A 90mm AIRSPACE,
EXTERIOR WALL - WALL - SIDING RSI 2.97 REQUIRED W/ HRV (TABLE 9.36.2.5.B) WALLBOARD INTERIOR AIR FILM - 0.12
ASSEMBLY TAKEN FROM TABLE CM-1.
W2 - STUCCO EXTERIOR WALL, RSI 2.97 W6 ASSEMBLY EFFECTIVE RSI 4.18 F3
STUCCO 1 HOUR FIRE RESISTANCE - EXTRUDED POLYSTYRENE INSULATION BOARD
REQUIRED W/ HRV (TABLE 9.36.2.5.B) THICKNESS
RSI/ mm RSI-VALUE - FLOOR TO SPEC.
W2 RATING
(mm)
5 RSI/ mm OF 0.035 RSI/ mm, TAKEN FROM
- 8" T&G SUB-FLOOR
- 1
8" ACRYLIC STUCCO
THICKNESS
RSI/ mm RSI-VALUE - METAL SIDING EXTERIOR AIR FILM - 0.03 BELOW GRADE WALLS ASSEMBLIES: TABLE CM-1.
FINISH
(mm)
- 11- 78" ENGINEERED JOISTS @ - RSI RATING FOR ABOVE GRADE WALL WITH
EXTERIOR AIR FILM - 0.03 - BUILDING PAPER METAL SIDING - -
19.2" O.C. (T0 MANUF. SPECS) 2x6 WOOD STUDS @ 24" O.C. W/ R20 BATT
- 1 21" EXTRUDED - 5
8" DENSGLASS BUILDING PAPER - -
STUCCO FINISH 3.175 0.0009 0.002 FOUNDATION/ FROST - FINISH CEILING TO SPEC. INSULATION OF 2.53 RSI, TAKEN FROM TABLE
POLYSTYRENE SHEATHING W11 - FOUNDATION/ FROST WALL, RSI 2.97
EXTRUDED POLYSTYRENE DENGLASS SHEATHING 15.875 0.12 WA-2.
INSULATION INSULATION (XPS)
38.1 0.035 1.33 - 2"x6"STUDS @ 24" O.C. WALL REQUIRED W/ HRV (TABLE 9.36.2.5.B) BASEMENT CONCRETE
- FLUID APPLIED AIR & 2x6 WOOD STUD @ 24" W12 - RSI RATING FOR ABOVE GRADE WALL WITH
FLUID APPLIED AIR & W/ R-22 BATT SLAB FLOOR
VAPOUR BARRIER - 0.00 O.C. FILLED WITH R-22 - 2.67 - EXTERIOR WATER-/ THICKNESS
RSI/ mm RSI-VALUE 2x6 WOOD STUDS @ 24" O.C. W/ R22 BATT
VAPOUR BARRIER INSULATION BATT INSULATION (mm) F4
3 DAMPPROOFING EXTERIOR WATER/
INSULATION OF 2.67 RSI, TAKEN FROM TABLE
- 8" OSB SHEATHING OSB SHEATHING 9.525 0.0098 0.09 - 6 MIL POLY. SEALED AT 6MIL POLYETHYLENE - - - 4" (3.5" MIN) CONC. SLAB
- - - 8" CONCRETE DAMP-PROOFING WA-2.
- 2"x6"STUDS @ 24" 2x6 WOOD STUDS @ TOP AND BOTTOM VAPOUR BARRIER - 6 MIL POLY VAPOUR BARRIER
TYPE X GYSUM
FOUNDATION WALL CONCRETE FOUNDATION - RSI RATING FOR ABOVE GRADE WALL WITH
O.C. W/ R-22 BATT 24" O.C. FILLED WITH - 2.53 - 5
8" TYPE X GYPSUM 12.7 0.0063 0.10 203 0.0004 0.08 - GRANULAR GRAVEL FILL TO
R-20 BATT INSULATION WALLBOARD - 2" AIR GAP WALL 2x6 WOOD STUDS @ 12" O.C. W/ R24 BATT
INSULATION BOARD RADON LEAK REQUIREMENTS
INTERIOR AIR FILM - 0.12 - 2x4 FRAMING AT 24" 2" AIR GAP 0.00 INSULATION OF 2.60 RSI, TAKEN FROM TABLE
- 6 MIL POLY. SEALED 6MIL POLYETHYLENE
VAPOUR BARRIER
- 0.00 O.C. FILLED WITH 5- 2x6 WOOD STUDS @ 24" WA-2.
AT TOP AND BOTTOM ASSEMBLY EFFECTIVE RSI 3.04
1 O.C. FILLED WITH 5- 21" - 2.81 GARAGE CONCRETE - RSI RATING FOR BELOW GRADE 2x6 WOOD
1 GYSUM BOARD 12.7 0.0063 0.08 2" THICH R20 BATT
- 2" GYPSUM BOARD R-20 BATT INSULATION SLAB STUD WALL @ 24" O.C. W/ R20 BATT
INSULATION
INTERIOR AIR FILM - 0.12 EXTERIOR CANTILEVER 6MIL POLYETHYLENE F5 INSULATION IS 2.81, TAKEN FROM TABLE
W8 - EXTERIOR CANTILEVER WALL - STUCCO, RSI - 6 MIL POLY. SEALED - 0.00
WALL - STUCCO VAPOUR BARRIER - 4" CONC. SLAB REINFORCED W/
ASSEMBLY EFFECTIVE RSI 4.18 2.97 REQUIRED W/ HRV (TABLE 9.36.2.5.B) AT TOP AND BOTTOM WB-2.
W7 GYSUM BOARD 12.7 0.0063 0.08 10-M REBAR @ 24 O.C. IN A GRID
- 1 - CONCRETE RSI/ MM VALUE OF 0.0004 TAKEN
- 1 2" GYPSUM BOARD - 6 MIL POLYTHENE VAPOUR BARRIER
8" ACRYLIC STUCCO THICKNESS
RIM BOARD - VINYL W2 - VINYL SIDING EXTERIOR RIM BOARD (mm)
RSI/ mm RSI-VALUE
INTERIOR AIR FILM - 0.12 FROM TABLE CM-1.
WALL, RSI 2.97 REQUIRED W/ HRV FINISH - 6 (MINIMUM) GRANULAR FILL 5
SIDING 1
EXTERIOR AIR FILM - 0.03 ASSEMBLY EFFECTIVE RSI 3.09 - 8" DENGLASS SHEATHING RSI 0.09 VALUE OF
W3 (TABLE 9.36.2.5.B) - 1 2" EXTRUDED TAKEN DIRECTLY FROM DENGLASS' WEBSITE
STUCCO FINISH 3.175 0.0009 0.002
- VINYL SIDING THICKNESS POLYSTYRENE
- BUILDING PAPER
(mm)
RSI/ mm RSI-VALUE
INSULATION
EXTRUDED POLYSTYRENE WALKOUT W5 - EXTERIOR WALKOUT FOUNDATION - RSI/ mm RATING OF SPRAYED
EXTERIOR AIR FILM - 0.03
- FLUID APPLIED AIR &
INSULATION BOARD (XPS)
38.1 0.035 1.33
FOUNDATION WALL WALL, RSI 2.97 REQUIRED W/ HRV ROOF ASSEMBLIES: POLYURETHANE FOAM RATING OF 0.026/ mm
- 1- 81" ENGINEERED RIM FLUID APPLIED AIR & 13 (TABLE 9.36.2.5.B) IS TAKEN FROM TABLE CM-1.
- 0.00
BOARD VINYL SIDING - 0.11 VAPOUR BARRIER VAPOUR BARRIER
5
- 4" EXTRUDED THICKNESS
RSI/ mm RSI-VALUE
- 11- 78" ENGINEERED BUILDING PAPER - 0.00 - 8" DENGLASS DENGLASS SHEATHING 28.575 0.0098 0.09 POLYSTYRENE
(mm)
EXACT URL FOR PAGE IS:
EXTRUDED POLYSTYRENE R1 - CEILING BELOW ATTIC, RSI 8.67
FLOOR JOISTS @ 19.2" OSB ENGINEERED RIM SHEATHING 2x6 WOOD STUDS AT 24" INSULATION BOARD 102 0.035 3.57 ROOF ASSEBLY https://www.nrcan.gc.ca/energy/efficiency
INSULATION (XPS) REQUIRED W/HRV (TABLE 9.36.2.6.B)
BOARD (28.575mm 28.575 0.0098 0.09 - 2"x6"STUDS @ 24" O.C. FILLED WITH R-20 - 2.53 R1
O.C. W/ R-28 CAVITY x0.0085) (XPS) - TYPE 3 EXTERIOR WATER/ /housing/new-homes/energy-starr-new-
O.C. W/ R-20 BATT BATT INSULATION - - - ASPHALT SHINGLES THICKNESS
FILL 11-7/8 ENGINEERED - EXTERIOR WATER/ DAMP-PROOFING (mm)
RSI/ mm RSI-VALUE homes-standard/tables-calculating-
- 6 MIL POLY. VAPOUR FLOOR JOIST @ 19.2" INSULATION 6MIL POLYETHYLENE
- 0.00 DAMP-PROOFING CONCRETE FOUNDATION TO SPEC. effective-thermal-resistance-opaque-
- 4.61 VAPOUR BARRIER 203 0.0004 0.08 EXTERIOR AIR FILM - 0.03
BARRIER O.C. W/ R-28 CAVITY - 6 MIL POLY. SEALED - 8" CONCRETE WALL - BUILDING PAPER assemblies/14176#R3-2
FILL TYPE X GYSUM
AT TOP AND BOTTOM WALLBOARD
12.7 0.0063 0.10
FOUNDATION WALL ASSEMBLY EFFECTIVE RSI 3.65 - 7
16" OSB SHEATHING
CELLULOSE FIBRE BLOWN
6MIL POLYETHYLENE 355.6 .025 8.89
- 0.00 5 INSULATION
VAPOUR BARRIER - 8" TYPE X GYPSUM INTERIOR AIR FILM - 0.12 - ENG. APP. TRUSSES @ RSI RATING FOR ABOVE GRADE WALL WITH 2x6
2"x4" BOTTOM
WALLBOARD 24" O.C. WOOD STUDS @ 8" O.C. W/ R24 BATT INSULATION
INTERIOR AIR FILM - 0.12
ASSEMBLY EFFECTIVE RSI 4.20 FLOOR ASSEMBLIES: - BLOW IN INSULATION
CHORD @ 24" O.C.
- 0.00

ASSEMBLY EFFECTIVE RSI 4.96 6MIL POLYETHYLENE IS 2.5, IS TAKEN FROM CANADIAN WOOD COUNCIL
- 0.00
EQUAL TO RSI VALUE VAPOUR BARRIER WEB SITE, EXACT URL FOR PAGE IS :
INTERIOR LOAD BEARING OF R50
RIM BOARD - ACRYLIC FLOOR ABOVE F1 - FLOOR ABOVE UNHEATED GARAGE GYPSUM BOARD 12.70 .0063 .08 http://effectiver.ca/calculator/wall.php?id=6521
W4 - STUCCO EXTERIOR RIM BOARD RSI 2.97 WALL SPACE, RSI 5.02, REQUIRED W/HRV - 6 MIL POLY INTERIOR AIR FILM
STUCCO REQUIRED W/ HRV (TABLE 9.36.2.5.B) W8 GARAGE 1 (HEAT FLOW UPWARDS)
- 0.11
W4 - 2x6 WOOD STUD WALL F1 (TABLE 9.36.2.6.A) - 2" DRYWALL TO SPEC FIRE RESISTANCE RATING NOTES:
1 - 5 ASSEMBLY EFFECTIVE RSI 9.11 - -FIRE RESISTANCE RATING FOR ASSEMBLY W7
8" OSB FLOOR THICKNESS
- 8" ACRYLIC STUCCO THICKNESS
(mm)
RSI/ mm RSI-VALUE ALIGNED WITH JOISTS ABOVE (mm)
RSI/ mm RSI-VALUE

FINISH 3 SHEATHING - CANTILEVER WALL FINISHED WITH METAL

EXTERIOR AIR FILM - 0.03 - 8" PLYWOOD SHEATHING ON
AIR FILM (HEAT FLOW
- 0.16 SIDING WAS BASED ON W1d FROM TABLE
- 1 21" EXTRUDED ONE SIDE OF WALL - 11- 78" ENGINEERED DOWNWARD)
STUCCO FINISH 3.175 0.0009 0.002 9.10.3.1.-A FROM THE NBC-2019AE.
POLYSTYRENE JOISTS @ 19.2" O.C. OSB FLOOR SHEATHING 15.875 .0098 0.16
EXTRUDED POLYSTYRENE
- MIN. 6" AIR GAP - W1d CREATES A 1 HOUR FIRE RESISTANCE
INSULATION INSULATION BOARD (XPS)
38.1 0.035 1.33 11- 78" ENGINEERED JOIST
PLUMBING/ MECHANICAL - 2"x8" FRAME W/ R-31
- 0.00 RATING FOR BOTH LOAD BEARING AND
- FLUID APPLIED AIR & FLUID APPLIED AIR &
@ 19.2" O.C.
- 0.00
WALL BATT INSULATION AIR SPACE (HEAT FLOW NON-LOAD BEARING WALLS WITH A S.T.C.
VAPOUR BARRIER VAPOUR BARRIER - 0.22
OSB ENGINEERED RIM W9 - 6 MIL POLYETHYLENE
DOWNWARD) RATING OF 32.
- 11- 78" ENGINEERED BOARD (28.575mm 28.575 0.0098 0.09 - 2x6 WOOD STUD WALL 2"x8" WOOD FRAME @ - AS PER TABLE D-3.1.1.-A GYPSUM BOARD
FLOOR JOISTS @ 19.2" x0.0085)
SHEET 24" O.C. W/ R41 BATT - 5.30
ALIGNED WITH JOISTS ABOVE 1 HAS A FLAME-SPREAD RATING FOR A
O.C. W/ R-28 CAVITY 11-7/8 ENGINEERED - 2" GYPSUM BOARD INSULATION
FLOOR JOIST @ 19.2"
UNFINISHED SURFACE.
FILL - 4.61
TYPICAL EXTERIOR 6MIL POLYETHYLENE
- 0.00
O.C. W/ R-28 CAVITY TYPICAL EXTERIOR TALL WALL - VINYL SIDING VAPOUR BARRIER
- 6 MIL POLY. SEALED FILL EXTERIOR WALL, RSI 2.97 REQUIRED W/ HRV
AT TOP AND BOTTOM 6MIL POLYETHYLENE
TALL WALL - SIDING GYPSUM BOARD 12.7 0.0063 0.08
- 0.00 W10 (TABLE 9.36.2.5.B)
1 VAPOUR BARRIER
- 2" GYPSUM BOARD 1 HOUR FIRE RESISTANCE THICKNESS
RSI/ mm RSI-VALUE
EXTERIOR AIR FILM - 0.03
INTERIOR AIR FILM - 0.12 (mm)
RATING ASSEMBLY EFFECTIVE RSI 5.95
ASSEMBLY EFFECTIVE RSI 6.18 EXTERIOR AIR FILM - 0.03
- METAL SIDING
- BUILDING PAPER VINYL SIDING - 0.11
5
- 8" DENSGLASS
BUILDING PAPER - 0.00
SHEATHING OSB SHEATHING 9.525 0.0098 0.09
- 2"x6"STUDS @ 24" O.C. 2x6 WOOD STUDS AT 12"
W/ R-24 BATT O.C. FILLED WITH R-24 - 2.60
INSULATION BATT INSULATION
- 6 MIL POLY. SEALED AT 6MIL POLYETHYLENE
- 0.00
VAPOUR BARRIER
TOP AND BOTTOM
5 GYSUM BOARD 12.7 0.0063 0.08
- 8" TYPE X GYPSUM
BOARD INTERIOR AIR FILM - 0.12

ASSEMBLY EFFECTIVE RSI 3.03

ADDRESS: LEGAL: LOT: BLOCK PLAN

Note: ALL INTERIOR WALLS ARE TO BE
New Day Drafting LTD. 02 12 232 2422 SYMBOL LEGEND:
CONSTRUCTED FROM 2x4 STUDS AT 16
Sunpreet Grewal SUN ESTATE HOMES
O.C. UNLESS OTHERWISE NOTED ON F.D.
780-265-1042 227 28 STREET SW SQUARE FEET -FLOOR DRAIN S -SMOKE DETECTOR
DRAWINGS.
[email protected] EDMONTON, AB MAIN: UPPER: BSMT: TOTAL: SCALE: DATE: PAGE:
www.newdaydrafting.com 3/16" = 1'-0" F - CEILING EXHAUST FAN CD -CARBON MONOXIDE DETECTOR
REV: DESCRIPTION: DATE:
SPECIFICATIONS:
BASEMENT CONCRETE: EXTERIOR WINDOWS AND DOORS: · ALL DIMENSIONAL FLOOR JOISTS TO BE #2D.F. OR BETTER AND DOUBLED AROUND
ALL OPENINGS.
· 24"x8" CONCRETE FOOTING (SIZE MAYBE CHANGED UNDER RECOMMENDATION DOORS: · PRE-MANUFACTURED FLOOR SYSTEM - AS PER SUPPLIER
OF ENGINEERING) · FRONT AND REAR INSULATED C/W DEADBOLTS · ROOF TRUSSES TO BE ENGINEERED BY OTHERS
· 8" THICK CONCRETE WALLS C/W 2-10 REBAR AT THE TOP AND BOTTOM · ALL CANTILEVERED FLOORS TO HAVE R32 INSULATION.
· TELEPOST PADS IN ACCORDANCE WITH ENGINEERING WINDOWS: · ALL M=L &/ OR GLULAM BEAMS TO BE ENGINEERED BY OTHERS.
· ALL THE ABOVE STRUCTURAL CONCRETE TO CONSIST OF MIN. 32.5 MPA · MAINTENANCE FREE TRIPLE GLAZED ENERGY SAVER UNITS C/W SCREENS AS · INDICATES 2'-8"x6'-8" DOOR C/W 1 HR. MIN. FIRE RATING & SELF CLOSER AND
SULPHATE RESISTANT OR TO MATCH RECOMMENDATIONS FROM SOIL REPORT. PER PLANS. WEATHERPROOFING.
· 3" (MIN) CONCRETE FLOOR POURED OVER 6 MIL CGSB PLOY AND GRANULAR · PROVIDE FLASHING ABOVE ALL EXTERIOR WINDOWS AND DOORS. · ATTIC ACCESS MUST BE 22"x28" (MIN.) & INCLUDE INSULATION &
FILL THAT MEETS RADON REQUIREMENTS. WEATHERPROOFING.
· DAMP-PROOFING-ASPHALT EMULSION APPLIED TO EXTERIOR OF CONCRETE · ROOF VENTS MUST BE PROVIDED AS PER CODE.
WALLS. INTERIOR FINISHES: · PROVIDE INSULATION STOPS.
· WEEPING TILE, 4" CONTINUOUS PERFORATED PIPE AROUND THE FOUNDATION · ALL INTERIOR DOORS, CLOSET DOORS, BASEBOARDS & TRIMS TO BE · PROVIDED PRE-FINISHED FASCIA & EAVESTROUGHING.
C/W 6" OF ROCK. COLONIST FINISH · WINDOW SIZES INDICATES ARE APPROXIMATE GLASS SIZE ONLY. CONFIRM ALL
· CLOSET SHELVES TO BE 12" PRE-FINISHED WIRE SHELVES WINDOW R.O.'S SIZES W/OWNER PRIOR TO ANY INSTALLATION OR ORDERING.
· LIVEN CLOSETS TO BE 4-16" PRE-FINISHED WIRE SHELVES · FLASHING MUST BE PROVIDED OVER DOORS AND WINDOWS.
FRAMING: · MIRRORS ABOVE ALL BATH VANITIES · GRADE LINE IS SUGGESTED ONLY. VERIFY STEPS & ACTUAL GRADE LINE ON SITE
· BEAMS WITH STEEL TELEPOSTS AS PER PLANS · WOOD RAILING TO BE MINIMUM 36" IN HEIGHT W/CONISTIONS.
· BEAMS AS PER ENGINEERING · MAIN FLOOR HT. TO ATTACHED GARAGE SLAB HT. IS TO BE VERIFIED BY
· ENGINEERED FLOOR SYSTEM 11-1/2" DEPTH @ 19.2" O.C. STAIRS: SURVEYOR W/ACTUAL GRADE ON SITE.
· 5
8" OSB TONGUE AND GROVE SUB-FLOOR, GLUED AND SCREWED
· MAXIMUM RISE SHALL BE NOT MORE THAN 7 78" AND MINIMUM SHALL BE 6" · PROVIDE SMOKE DETECTOR(S) AS PER CODE
· MINIMUM RUN SHALL 10" · MIN 2" CLEARANCE AROUND FURNACE & FI.P. FLUES
EXTERIOR WALLS: · MINIMUM THREAD SHALL BE 11", WERE NOSING IS 1" · DRYER VENT MUST BE 4" ∅ C/W HOOD
· 2"x6" @ 24" O.C. C/W 2-2"X6" TOP PLATES AND 1-2"x6" BOTTOM PLATE W/ · MINIMUM HEIGHT OF HANDRAIL SHALL BE 31 21" AT THE EDGE OF THE NOSING · CONTINUOUS WOOD STRAPPING IS T CONSISTS OF CROSS BRIDGING, SOLID
R22 BATT INSULATION C/W CGSB POLY VAPOUR BARRIER AND 21" DRYWALL · HEIGHT OF HANDRAIL SHALL BE 32" (MIN.) TO 36" (MAX) AT THE EDGE OF BLOCKING OR DOUBLE FRAMING UNDER ALL PARALLEL PARTITIONS AND AROUND
3 THE NOSING ALL OPENINGS
· 8" OSB EXTERIOR SHEETING GLUED TO STUDS C/W CSA S101 WITH SIDEYARDS
< 2.4m (IF REQUIRED) · MINIMUM HEADROOM IS 6'-5" · END BEARING OF JOISTS AND RAFTERS SHALL NOT BE LESS 1 21".
· NON-HARDENING CAULKING AROUND ALL EXTERIOR OPENINGS. · FIRE STOPS ARE TO BE PROVIDED AT ALL CONCEALED SPACES AT FLOOR, CEAILING
HEATING: AND ROOF LEVELS INCLUDING THE SPACE BETWEEN THE CHIMNEY FLUE AND
· FURNACE TO BE GAS FIRED 92% OR BETTER EFFICIENCY, FORCED AIR SHAFT WHERE IT PASSES THROUGH DIFFERENT LEVELS.
INTERIOR WALLS: COMBINED WITH HEAT RECOVERY VENTILATION (HRV) UNIT.
· 2"x4" @ 24" O.C. C.W 2-2"X4" TOP PLATES AND 1-2"x4" BOTTOM PLATE · HUMIDIFIERS TO BE INSTALLED
· DRYER VENT TO BE VENTED TO OUTSIDE AND CAPPED REINFORCING NOTES:
ROOF: · EACH DWELLING UNIT TO HAVE INDEPENDENT HEATING AND VENTILATION · CONCRETE FOUNDATION WALLS TO BE R/W 10M@24" O.C. (VERT.) & 1OM @ 18"
· ENGINEERED TRUSSES @ 24 O.C. SYSTEM COMPLYING WITH SEC. [email protected] O.C. (HORIZ.) - 2-10 DOWELS E/S OF OPENINGS.
7 · CONCRETE STRIP FOOTING TO BE R/W 2-10M BARS - CONTINUOUS
· 16" OSB SHEATHING GLUED TO STUDS C/W "H" CLIPS BASEMENT SLAB R/W WWM C/W 6 MIL POLY MOISTURE BARRIER ON COARSE
ELECTRICAL:
· ASPHALT SHINGLES C/W EAVE/ VALLEY PROTECTION
· 100 AMP SERVICE C/W CIRCUIT PANEL CLEAN GRANULAR TO CONTAIN AND PREVENT RADON GAS FROM LEAKING
· COPPER WIRING THROUGHOUT THROUGH.
INSULATION/ DRYWALL:
· 220 VOLT PLUG FOR RANGE AND DRYER · A 4MM SIEVE SHALL BE PLACED UNDER THE FLOOR-ON-GROUND.
· GROUND FAULT INTERRUPTER PLUGS IN BATHROOMS, ALL ON SAME CIRCUIT. · CONC. PAD FOOTINGS R/W 10M @ 12 O.C. E/W
BASEMENT:
· EXTERIOR WEATHER PROOF PLUG ON GFI CIRCUIT · GARAGE SLAB R/W 2-10M BARS @ 12" O.C. E/W ON COMPACTED SAND - TO 98%
· 2"x4" WOOD STUDS WITH 2" AIR GAP BETWEEN CONCRETE FOUNDATION @ 24"
· DIRECT WIRED SMOKE DETECTORS AS PER PLANS PROCTOR
O.C. W/ R-20 BATT INSULATION C/W CGSB POLY VAPOUR BARRIER
· LIGHT PACKAGE AS PER PLANS · GRADE BEAM R/W 2-10M CONTINUOUS T&B C/W 10M TIES @ 18" O.C.
· VENTED FOOD FAN OVER RANGE · TYPICAL PILES TO BE 12" ∅ X 14'-0" DEEP R/W 3-15M - EXTENDED 60" ABOVE
EXTERIOR FINISHES:
· CABLE TV OUTLETS AS PER PLAN CONCRETE & BENT E/W - OTHER PILES TO BE ENGINEERED.
· "APPROVED" BUILDING WRAP
· TELEPHONE OUTLETS AS PER PLAN · TIE SLAB &/ OR SIDEWALK TO GRADE BM./ FDN WALL - 10M TIES @ 12" O.C.
· PRE-FINISHED VINYL SIDING
· PLASTIC VAPOUR RATED BOXES ON ALL EXTERIOR WALL AND CEILINGS · TIE GRADE BEAM TO FDN. WALL W/ 2-10M T&B @ ELE
· PRE-FINISHED ALUMINUM SOFFITS, FASCIA, EVES TROUGH AND DOWNSPOUTS.
OUTLETS · ENGINEER'S DRAWINGS &/ OR STAMP TO BE THE RESPONSIBILITY OF BUILDER/
· PRE-FINISHED OR PAINTED BOARD & BATTON SIDINGS
· ROUGH IN DISHWASHER OWNER.
· ROUGH IN VAC OUTLETS
· DUPLEX RECEPTACLES AND SWITCHES TO BE WHITE MISCELLANEOUS:
· PLUMBING CLEAN OUT ACCESS TO BE PROVIDED
· FINISHED WOOD OR METAL RAILING TO HAVE MAX 4" OPENING BETWEEN
GENERAL NOTES: BALUSTERS
· ALL CONSTRUCTION MUST CONFIRM TO LOCAL BYLAWS &/ OR ALBERTA · NO UNTREATED WOOD PRODUCTS TO BE WITHIN 8" OF FINISHED GRADE
BUILDING CODE. · BATHROOM HRV INTAKE VENT TO BE IN ACCORDANCE WITH ALBERTA BUILDING
· WEEPING TILE TO BE INSTALLED AROUND ALL STRIP FOOTING AND TIED TO CODE.
DRAINAGE AS PER CODE.
ADDRESS: LEGAL: LOT: BLOCK PLAN
Note: ALL INTERIOR WALLS ARE TO BE
New Day Drafting LTD. 02 12 232 2422 SYMBOL LEGEND:
CONSTRUCTED FROM 2x4 STUDS AT 16
Sunpreet Grewal SUN ESTATE HOMES
O.C. UNLESS OTHERWISE NOTED ON F.D.
780-265-1042 227 28 STREET SW SQUARE FEET -FLOOR DRAIN S -SMOKE DETECTOR
DRAWINGS.
[email protected] EDMONTON, AB MAIN: UPPER: BSMT: TOTAL: SCALE: DATE: PAGE:
www.newdaydrafting.com F - CEILING EXHAUST FAN CD -CARBON MONOXIDE DETECTOR
REV: DESCRIPTION: DATE:
 14" HIGH BLOW INSULATION ALL JOINTS IN EXTERIOR BUILDING PAPER MUST
(R50 VALUE) BE OVERLAPPED AND TAPED TO CREATE A
SEALANT BEAD/ TAPE COMPLETE SEALED LAYER.
FOR CONTINOUS SEAL
INSULATION STOP (TYPICAL) ALL JOINTS AND OPENINGS IN INTERIOR VAPOUR
TYVEK BUILDING
PAPER BARRIER MUST BE EITHER SEALED BY THE USE OF
R28 BATT INSULATION CAULKING OR TAPE. THIS BE DONE WHERE
TYVEK BUILDING ALL JOINTS AND TRANSITIONS VAPOUR BARRIER OVERLAPS OR ENDS AT THE
B/N JOISTS
PAPER & PENETRATIONS MUST BE SEALED FLOOR AND IN BETWEEN JOISTS TO CREATE A
WITH TAPE AND SEALANT FORMING COMPLETE SEAL.
A CONTINUOUS AIR BARRIER
CGSB APP. POLY VAPOUR **** ALL BUILDING PAPER, VAPOUR BARRIER AND
AIR BARRIER TO BE LAPPED TYVEK BUILDING
2x4 WOOD STUD SEALANT/ TAPE IS SHOWN IN GREEN.
& SEALED FORMING A PAPER
SEALANT BEAD/ TAPE LADDER FRAME
FOR CONTINOUS SEAL CONTINUOUS SEAL THAT SEALANT BEAD/ TAPE ALL BARRIER SYSTEM MUST BE CONTINUOUS:
(TYPICAL) IS ALSO STRUCTURALLY FOR CONTINOUS SEAL
SUPPORTED (TYPICAL) - ACROSS ALL CONSTRUCTION, CONTROL
CGSB APP. POLY VAPOUR AIR SEALANT BEAD/ TAPE
AND EXPANSION JOINTS
FOR CONTINOUS SEAL
BARRIER TO BE LAPPED & SEALED - ACROSS ALL JUNCTIONS BETWEEN
FORMING A CONTINUOUS SEAL THAT (TYPICAL) DIFFERENT BUILDING MATERIALS AND
IS ALSO STRUCTURALLY SUPPORTED ASSEMBLIES
CGSB. APP. POLY VAPOUR/ AIR BARRIER - AROUND ALL PENETRATION POINTS
TO BE LAPPED & SEALED AT EACH JOIST THROUGH ALL BUILDING ASSEMBLIES.
SPACE FOR A CONTINUOUS SEAL
ADDITIONAL NOTES:

- THE EXTERIOR SHEATHING MEMBRANE MAY

SEALED POLY VAPOUR INTERIOR BARRIER WALL TO CEILING/ ATTIC INSULATION RIM JOIST SEALING BE THE PRINCIPAL AIR BARRIER IF ALL
JOINTS ARE SEALED, PLASTIC CAP
FASTENERS ARE USED AND TOP AND
BOTTOM CONNECTIONS ARE SEALED. THE
BOTTOM IS TO BE SEALED TO THE
CANTILEVER ASSEMBLY DETAIL BOX W/ SOLID SEALING CONCRETE WITH A COMPATIBLE PEAL AND
5 FLANGE STICK PRODUCT AND THAT THE TOP IS TO
- 8"OSB SUB-FLOOR
BE SEALED TO THE UPPERMOST TOP PLATE
- 11- 78" ENG. WOOD I JOIST @ 19.2" WITH THE A COMPATIBLE PEAL AND STICK
O.C. WITH R41 BATT INSULATION PRODUCT. THE INTERIOR CEILING AIR
ELECTRICAL OUTLET
- POLYETHYLENE VAPOUR BARRIER BARRIER SHOULD BE SEALED TO THIS SAME
SECURED W/ FLANGE
- NON-VENTED SOFFIT TOP PLATE. COMPLETING CONTINUITY.
VAPOUR BARRIER SEALED GAP SEALER -
- WHERE THE AIR BARRIER SYSTEM CONSISTS
TO UNDERSIDE OF SUB-FLOOR INSULATING FOAM ALL JOINTS MUST HAVE
OF FLEXIBLE SHEET MATERIAL, ALL THE
SEALER IN JOINTS A SEALANT BEAD OR BE
SEALANT BEAD OR JOINTS MUST BE LAPPED A MINIMUM 50MM,
TAPED
TAPED (TYPICAL) SEALED AND STRUCTURALLY SUPPORTED.
- 6 MIL POLY CUT AROUND JOISTS IN THE
INTERIOR CANNOT ACTS AS THE PRINCIPAL
AIR BARRIER; THEREFORE FRAMING MUST BE
MADE AIR-TIGHT.
SEALANT BEAD/ ALL ELECTRICAL CONNECTIONS - ALL APPROVED SEALANT AT MECHANICAL
TAPE FOR CONTINOUS CAULKING/ SEALANT TO SEAL TO BE SEALED JOINTS MUST BE MECHANICALLY
CGSB.APP. POLY VAPOUR/
UNDERSIDE OF JOISTS COMPRESSED BETWEEN SOLID BACKING.
SEAL (TYPICAL) AIR BARRIER TO BE LAPPED &
SEALED AT EACH JOIST SPACE - MATERIALS INTENDED TO PROVIDE THE
CGSB. APP. POLY VAPOUR/ PRINCIPAL RESISTANCE TO AIR LEAKAGE
SEALANT BEAD/ FOR A CONTINUOUS SEAL CGSB.APP. POLY VAPOUR/ AIR BARRIER TO BE LAPPED
AIR BARRIER TO BE LAPPED & MUST CONFORM TO CAN/ULC-S741. AIR
TAPE FOR CONTINOUS & SEALED AT EACH JOIST SPACE
SEALED AT EACH JOIST SPACE BARRIER MATERIALS - SPECIFICATION.
SEAL (TYPICAL) FOR A CONTINUOUS SEAL
FOR A CONTINUOUS SEAL
TYVEK BUILDING
PAPER TO WRAP
AROUND UNDERSIDE
OF CANTILEVER
CANTILEVER SEALING DOOR/ WINDOW BARRIER OUTLET BOX & LIGHTS
NOTE: OTHER CEILING FIXTURES SUCH AS POT LIGHTS
WILL BE SEALED WITH THIS METHOD AS WELL R50 STYROFOAM LID

TYVEK SEALANT BEAD OR TAPED

BUILDING FOR CONTINOUS SEAL (TYP.) SEALANT BEAD/ TAPED
PAPER FOR CONTINUOUS SEAL

R22 BATT INSULATION

VAPOUR BOX R28 INSULATION
AROUND VENT
CELL FOAM GASKET AROUND ACCESS
GRAVITY SEALANT BEAD/ TAPED AROUND PERIMETER HATCH
DAMPER FOR CONTINUOUS SEAL SEALANT BEAD/ TAPED
FOR CONTINUOUS SEAL

VAPOUR TO BE WRAP AROUND VENT

AND SEALED WITH SEALENT BEAB/ TAPE CGSB. APP. POLY VAPOUR/
CGSB. APP. POLY VAPOUR/ 22"x28" ATTIC AIR BARRIER TO BE LAPPED
FOR COMPLETE SEAL FROM EXTERIOR
AIR BARRIER TO BE LAPPED ACCESS & SEALED AT EACH JOIST
SEALANT BEAD/ TAPE FOR & SEALED AT EACH JOIST SPACE FOR A CONTINUOUS SEAL
CONTINOUS SEAL (TYPICAL) SPACE FOR A CONTINUOUS SEAL
ALL ELECTRICAL CONNECTION
CGSB. APP. POLY VAPOUR/ AIR BARRIER TO BE SEALED
TO BE LAPPED & SEALED AT EACH JOIST
SPACE FOR A CONTINUOUS SEAL

WALL VENTED DUCT CEILING ELECTRICAL FIXTURES ATTIC ACCESS

ADDRESS: LEGAL: LOT: BLOCK PLAN
Note: ALL INTERIOR WALLS ARE TO BE
New Day Drafting LTD. 02 12 232 2422 SYMBOL LEGEND:
CONSTRUCTED FROM 2x4 STUDS AT 16
Sunpreet Grewal SUN ESTATE HOMES
O.C. UNLESS OTHERWISE NOTED ON F.D.
780-265-1042 227 28 STREET SW SQUARE FEET -FLOOR DRAIN S -SMOKE DETECTOR
DRAWINGS.
[email protected] EDMONTON, AB MAIN: UPPER: BSMT: TOTAL: SCALE: DATE: PAGE:
www.newdaydrafting.com 3/8" = 1'-0" F - CEILING EXHAUST FAN CD -CARBON MONOXIDE DETECTOR
REV: DESCRIPTION: DATE:
 NOTE: INSULATION EACH ALL JOINTS IN EXTERIOR BUILDING PAPER MUST
1
2 LB SPRAY FOAM INSULATION SIDE OF DUCT BE OVERLAPPED AND TAPED TO CREATE A
MAY BE USED TO INSULATE COMPLETE SEALED LAYER.
DUCTS. HEAT DUCT
IF SPRAY FOAM IS AN INSULATED ALL JOINTS AND OPENINGS IN INTERIOR VAPOUR
SLEEVE MUST BE PLACED OVER BARRIER MUST BE EITHER SEALED BY THE USE OF
CGSB.APP. POLY VAPOUR/ DUCT BEFORE SPRAY FOAM. CAULKING OR TAPE. THIS BE DONE WHERE
AIR BARRIER TO BE LAPPED & VAPOUR BARRIER OVERLAPS OR ENDS AT THE
SEALED AT EACH JOIST SPACE FLOOR AND IN BETWEEN JOISTS TO CREATE A
FOR A CONTINUOUS SEAL COMPLETE SEAL.
SHEET METAL SURROUND,
MIN. 2" OF CLEARANCE **** ALL BUILDING PAPER, VAPOUR BARRIER AND
SEALANT/ TAPE IS SHOWN IN GREEN.

ALL BARRIER SYSTEM MUST BE CONTINUOUS:

HIGH TEMP. SEALANT - ACROSS ALL CONSTRUCTION, CONTROL

CGSB.APP. POLY VAPOUR/ AIR BARRIER TO SEALANT BEAD/ TAPPED
AND EXPANSION JOINTS
BE LAPPED & SEALED AT EACH JOIST FOR CONTINUOUS SEAL
- ACROSS ALL JUNCTIONS BETWEEN
SPACE FOR A CONTINUOUS SEAL RUBBER GASKET (TYP.)
DIFFERENT BUILDING MATERIALS AND
ASSEMBLIES
CGSB. APP. POLY VAPOUR/ AIR - AROUND ALL PENETRATION POINTS
PLUMBING STACK BARRIER TO BE LAPPED & THROUGH ALL BUILDING ASSEMBLIES.
SEALED AT EACH JOIST SPACE
FOR A CONTINUOUS SEAL ADDITIONAL NOTES:

- THE EXTERIOR SHEATHING MEMBRANE MAY

CHIMNEY/ MECHANICAL FLUES PLUMBING STACK HEAT DUCT FOR ROOMS OVER GARAGE BE THE PRINCIPAL AIR BARRIER IF ALL
JOINTS ARE SEALED, PLASTIC CAP
FASTENERS ARE USED AND TOP AND
BOTTOM CONNECTIONS ARE SEALED. THE
EXTERIOR BUILDING PAPER TO BE LAPPED &
SEALED AT EACH JOIST SPACE FOR A METHODS FOR SEALING SLAB BOTTOM IS TO BE SEALED TO THE
CONCRETE WITH A COMPATIBLE PEAL AND
CONTINUOUS SEAL STICK PRODUCT AND THAT THE TOP IS TO

BUILDING PAPER TO EXTEND

FROM RADON GAS DETAILS BE SEALED TO THE UPPERMOST TOP PLATE
WITH THE A COMPATIBLE PEAL AND STICK
PRODUCT. THE INTERIOR CEILING AIR

24" O.C. (TYP.)

MIN 6" UP ON INTERIOR SIDE
2x6 STUD CORNER BARRIER SHOULD BE SEALED TO THIS SAME
OF SHEATHING SECURE WITH
BACKING FOR DRYWALL TOP PLATE. COMPLETING CONTINUITY.
STAPLES AS NEEDED
SEALANT - WHERE THE AIR BARRIER SYSTEM CONSISTS
SEALANT OF FLEXIBLE SHEET MATERIAL, ALL THE
JOINTS MUST BE LAPPED A MINIMUM 50MM,
SEALED AND STRUCTURALLY SUPPORTED.
- 6 MIL POLY CUT AROUND JOISTS IN THE
NOTE: INTERIOR CANNOT ACTS AS THE PRINCIPAL
AIR BARRIER; THEREFORE FRAMING MUST BE
BUILDING PAPER TO EXTEND RECOMMANDED TO BUILD 2x6 CHANNEL MADE AIR-TIGHT.
MIN. 6" DOWN ON EXTERIOR INSTALL BUILDING PAPER 24" O.C. (TYP.) CORNER AT ALL INTERIOR - ALL APPROVED SEALANT AT MECHANICAL
SIDE OF SHEATHING. OVERLAP PARTITIONS THAT MEET
JOINTS MUST BE MECHANICALLY
WITH LARGE SECTION OF AT JOINTS ALL YEAR PERPENDICULARLY METHOD 1: EXTEND POLYSTYRENE VAPOUR METHOD 2: EXTEND POLYTHENE VAPOUR
COMPRESSED BETWEEN SOLID BACKING.
BARRIER PAST UP PAST TOP OF SLAB AND SEAL BARRIER TO TOP OF SLAB AND SEAL AND
BUILDING PAPER THEN SECURE ROUND FOR BETTER NOTE: AND ATTACH WITH SEALANT TO FOUNDATION ATTACH WITH SEALANT TO CORNER OF SLAB - MATERIALS INTENDED TO PROVIDE THE
AS NEEDED PRINCIPAL RESISTANCE TO AIR LEAKAGE
MOISTURE PROTECTION EXTENDED PLYWOOD TO CORNER ON BOTH WALLS FOR CONTINUOUS SEAL. AND FOUNDATION WALLS FOR CONTINUOUS
MUST CONFORM TO CAN/ULC-S741. AIR
SEAL.
EXTERIOR TO COVER FRAMING AND COMPLETE BARRIER MATERIALS - SPECIFICATION.
WITH DIVERGING STAPLES.
SEALANT

BUILDING PAPER AT PLYWOOD JOINTS TYPICAL FRAMING FOR DETAILS

BLOCKING MUST BE SECURELY
NAILED TO JOIST AND FDN. SILL
TO PROVIDE MAX. LATERAL METHOD 3: EXTEND POLYTHENE VAPOUR
4" FDN. WALL SUPPORT BARRIER TO COVER CONCRETE FOOTING. SEAL
1'- AND ATTACH BARRIER WITH SEALANT TO TOP
ENG. FLOOR
OF FOOTING FOR CONTINUOUS SEAL UNDER
JOIST
SLAB.

FOUNDATION
WALL
CENTER OF BASEMENT
SLAB

CENTER OF BASEMENT CENTER OF BASEMENT

SOLID BLOCKING @ SLAB SLAB
16" O.C. (SOLID RADON RADON
RADON

MATERIAL ONLY) 2x4 WALL FRAMED @ 16" O.C.

TO MACH HEIGHT OF JOIST.
ONLY USE WHEN PARALLEL
TO JOIST.
4"

AIR/SOIL GAS AIR/SOIL GAS 4" 4" AIR/SOIL GAS EXHAUST PIPE
FOUNDATION WALL BARRIER BARRIER BARRIER 4"

FOUNDATION WALL & JOIST TYPICAL RADON GAS

LATERAL SUPPORT EXTRACTION DETAILS
ADDRESS: LEGAL: LOT: BLOCK PLAN
Note: ALL INTERIOR WALLS ARE TO BE
New Day Drafting LTD. 02 12 232 2422 SYMBOL LEGEND:
CONSTRUCTED FROM 2x4 STUDS AT 16
Sunpreet Grewal SUN ESTATE HOMES
O.C. UNLESS OTHERWISE NOTED ON F.D.
780-265-1042 227 28 STREET SW SQUARE FEET -FLOOR DRAIN S -SMOKE DETECTOR
DRAWINGS.
[email protected] EDMONTON, AB MAIN: UPPER: BSMT: TOTAL: SCALE: DATE: PAGE:
www.newdaydrafting.com 3/8" = 1'-0" F - CEILING EXHAUST FAN CD -CARBON MONOXIDE DETECTOR
REV: DESCRIPTION: DATE:
 LINTEL ABOVE EXTERIOR TOP PLATES TO BE JOINED LINTEL ABOVE EXTERIOR DOOR WINDOW REINFORCEMENT NOTES:
WINDOWS AS TO CODE IN MIDDLE OF STUD ON AS TO CODE REQUIREMENT
REQUIREMENT EXTERIOR & INTERIOR WALLS FOR DOORWAY 1. PLACE ALL REINFORCEMENT 1-1/2" FROM
2'-0" MIN. INSIDE FACE OF WALL
OF 4' & OVER,
2x6 PONY WALL HEADER MAT. 2. REINFORCEMENT TO BE DEFORMED BILLET
2-10M REBAR 24"
ON EDGE STEEL CONFORMING TO CAN/CSA - G30.18
LONG ON A 45 DEG
- M92, MINIMUM YIELD STRENGTH 400
ANGLE AT EACH STEP
MPa.

11" MAX.
3. MAXIMUM WINDOW WIDTH NOT TO EXCEED
60".
4. ALL REINFORCEMENT SIZES SUSCEPTIBLE TO
CHANGE UNDER ENGINEERING REPORTS.
-
CRIPPLE
STUD

WINDOW OPENING

DOOR
OPENING STUD
WINDOW SILL

CRIPPLE TO BE
FULL LENGTH TO NOTE:
REBAR DETAIL FOR STEPPED DOUNDATION BOTTOM PLATE ALL NAILING PATTERNS AS
PER BUILDING CODE
WINDOW & DOORWAY FRAMING DETAIL

TOP OF FOUNDATION
WALL
1'-5 1/2"

8"
WINDOW OPENING

LESS THAN 40"

2'-6"
2-15M @ 1" C/C ABOVE OPENING
BOTTOM OF WINDOW (IF THE OPENING DOES NOT EXTEND
MAY BE HIGHER OR TO TOP OF WALL) EXTEND MIN. 24" 1"
LOWER THAN GRADE BEYOND OPENING ON EACH SIDE
THAN INDICATED HERE
8"

5'-0" MAX
2'-0" MIN.
4'-0" MIN.

2-15M @ 3" C/C BELOW

NOTE: OPENING EXTEND MIN. 24"
WHEN A WINDOW WELL IS BEYOND OPENING ON
EACH SIDE
REQUIRED
WEEPING TILE MUST BE
INSTALLED BELOW THE
WINDOW AND COVERED 2-15 @ 3" C/C EACH
WITH GRAVEL. SIDE OF OPENING,
FULL HEIGHT

TYP. BASEMENT WINDOW TYP. CONC. RETAINING

BOTTOM OF CONC.
FOUNDATION WALL REINFORCEMENT AROUND BASEMENT
FRAMING DETAIL WALL SINGLE WINDOW DETAIL
ADDRESS: LEGAL: LOT: BLOCK PLAN
Note: ALL INTERIOR WALLS ARE TO BE
New Day Drafting LTD. 02 12 232 2422 SYMBOL LEGEND:
CONSTRUCTED FROM 2x4 STUDS AT 16
Sunpreet Grewal SUN ESTATE HOMES
O.C. UNLESS OTHERWISE NOTED ON F.D.
780-265-1042 227 28 STREET SW SQUARE FEET -FLOOR DRAIN S -SMOKE DETECTOR
DRAWINGS.
[email protected] EDMONTON, AB MAIN: UPPER: BSMT: TOTAL: SCALE: DATE: PAGE:
www.newdaydrafting.com 3/8" = 1'-0" F - CEILING EXHAUST FAN CD -CARBON MONOXIDE DETECTOR
REV: DESCRIPTION: DATE:
 CANTILEVER ASSEMBLY DETAIL
5
3/8" OSB SHEATHING 14" HIGH BLOW INSULATION - 8" OSB SUB-FLOOR
(R50 VALUE) - 11- 78" ENG. WOOD I JOIST @
INSULATION STOP 19.2" O.C. WITH R41 BATT
INSULATION
- MIL POLYETHYLENE VAPOUR
BARRIER
1'-0" MIN.

- NON-VENTED SOFFIT

W1
EXTEND SHEATHING
TO UNDERSIDE OF BOTTOM CHORD
TOP CHORD
EXTEND SHEATHING VAPOUR BARRIER SEALED F1
TO UNDERSIDE OF AT TOP OF WALL AND ROOF
TOP CHORD
CAULKING/ SEALANT AROUND
BUILDING PAPER TO BE
WINDOW FRAME FOR FULL SEAL
OVERLAP AND SEAL
BUILDING PAPER VAPOUR BARRIER SEALED
TYVEK BUILDING
INSTALLEDW/ WINDOWS AT BOTTOM OF WALL
PAPER TO WRAP
VAPOUR BARRIER SEALED AROUND UNDERSIDE
EXTERIOR WALL ASSEMBLY TO UNDERSIDE OF SUB-FLOOR OF CANTILEVER
- BUILDING PAPER R28 BATT INSULATION B/N JOISTS
3
- 8" OSB SHEATHING
- 2"x6" STUDS @ 24" O.C.
W/ R-22 BATT
INSULATION
ENGINEER APPROVED BEAM
BY OTHERS
ENGINEERED APPROVED CANTILEVER DETAIL
- 6 MIL POLY. SEALED AT
TOP AND BOTTOM CAULKING/ SEALANT
BEAM BY OTHERS
3 Scale: 1/4" = 1'-0"
1
- 2" GYPSUM BOARD TO SEAL UNDERSIDE W6
OF JOISTS
CAULKING/ SEALANT AROUND
AIR/ VAPOUR PERMEABLE
FILM BUILDING PAPER
WINDOW FRAME FOR FULL SEAL
GARAGE
WRAPPED AROUND WINDOW
SILLS AND DOOR
VAPOUR BARRIER SEALED
AT BOTTOM OF WALL 6 MIL POLY VAPOUR
TYVEK BUILDING PAPER BARRIER SEALED AS SLAB
R28 BATT INSULATION B/N JOISTS
AS AIR BARRIER
GAS BARRIER SEALED IN
BOTTOM PLATE TO BE ACCORDANCE WITH RADON
F5 GAS PREVENTION REQUIREMENTS
SEALED USING GASKET
2x4 WOOD STUD
AND AIR RETARDER
LADDER FRAME VAPOUR BARRIER SEALED
TO UNDERSIDE OF SUB-FLOOR
FROST WALL ASSEMBLY
CAULKING/ SEALANT TO SEAL
- EXTERIOR WATER/
UNDERSIDE OF JOISTS W13
DAMPPROOFING
- 8" CONCRETE FOUNDATION WALL W5
- 2"x6" FROST WALL W/ STUDS @ PERIMETER OF SLAB MUST BE SEALED USING
24" O.C. W/ R20 BATT 4" INCH WEEPING TILE
ONE OF THE CODE APPROVED REQUIREMENTS.
INSULATION COVERED IN GRAVEL
(SHOWN IN TYPICAL RESIDENTIAL DETAILS.)
- POLYETHYLENE SHEET SEE TYP. DETAIL
- 1 4" CONCRETE SLAB (TYP.)
2" GYPSUM BOARD 4" ∅ WEEPING TILE
POLYTHENE SOIL GAS BARRIER IS REQUIRED COVERED WITH
UNDER SLAB AND MUST EXTEND OVER MIN. 12" GRAVEL
8"CONC. WALL COVERED CONCRETE PADS FOR FULL CONTINUOUS SEAL ALL JOINTS IN EXTERIOR BUILDING PAPER MUST
WITH DAMP-PROOFING BE OVERLAPPED AND TAPED TO CREATE A
TO GRADE W/ 2-#10 COMPLETE SEALED LAYER.
REBAR @ T & b. CONCRETE FOOTING
ALL JOINTS AND OPENINGS IN INTERIOR VAPOUR BEYOND
BARRIER MUST BE EITHER SEALED BY THE USE OF
4" ∅ WEEPING TILE
CAULKING OR TAPE. THIS BE DONE WHERE
COVERED WITH
MIN. 12" GRAVEL
VAPOUR BARRIER OVERLAPS OR ENDS AT THE
FLOOR AND IN BETWEEN JOISTS TO CREATE A
WALKOUT WALL DETAIL
24"x8" CONC. FOOTING NOT LESS THAN 100MM OF COARSE CLEAN GRANULAR MATERIAL
COMPLETE SEAL. 4 Scale: 1/4" = 1'-0"
W/ 2-#10 CONT. REBAR CONTAINING NOT MORE THAN 10% OF MATERIAL THAT WILL PASS **** ALL BUILDING PAPER, VAPOUR BARRIER
(SIZE SUSCEPTIBLE TO A 4MM SIEVE SHALL BE PLACED UNDER THE FLOOR-ON-GROUND. AND SEALANT/ TAPE IS SHOWN IN GREEN.
CHANGE UNDER THE ROUGH-IN FOR RADON EXTRACTION TO BE INSTALLED AND MUST
ENGINEERING MEET EITHER PERFORMANCE OR PRESCRIPTIVE REQUIREMENT.
RECOMMENDATION)

WALL SECTION BUILDING SECTION

1 Scale: 1/4" = 1'-0"
2 Scale: 1/4" = 1'-0"

ADDRESS: LEGAL: LOT: BLOCK PLAN

Note: ALL INTERIOR WALLS ARE TO BE
New Day Drafting LTD. 02 12 232 2422 SYMBOL LEGEND:
CONSTRUCTED FROM 2x4 STUDS AT 16
Sunpreet Grewal SUN ESTATE HOMES
O.C. UNLESS OTHERWISE NOTED ON F.D.
780-265-1042 227 28 STREET SW SQUARE FEET -FLOOR DRAIN S -SMOKE DETECTOR
DRAWINGS.
[email protected] EDMONTON, AB MAIN: UPPER: BSMT: TOTAL: SCALE: DATE: PAGE:
www.newdaydrafting.com 1/4" = 1'-0" F - CEILING EXHAUST FAN CD -CARBON MONOXIDE DETECTOR
REV: DESCRIPTION: DATE: