Explosion protected CROUSE-HINDS

linear light fixture SERIES

CEAG ExLin series

LED linear fixtures for hazardous areas

[Link] EATON 1.2.1

 Introducing
CEAG ExLin / NE+
A linear LED engineered for use in
Zone 1 and 21 hazardous areas.

CEAG ExLin / NE+ delivers longer

life, improved efficiency and
superior performance with a
competitive payback vs. fluorescent
fixtures.

The following CEAG ExLin models will replace

2x18 W, 2x36 W and 2x58 W fluorescent fixtures,
as well as low bay fixtures above 150 W HID

Typical
lumens
with Typical
clear Lumens Equivalent energy
glass per fluorescent savings /
Model lens Wattage watt luminaire lifetime

ExLin 3L-1 2,910 22 W > 132 2 x 18 W > 40%

ExLin 5L-1 5,610 44 W > 127 2 x 36 W > 40%
ExLin 5L-2 5,810 44 W > 132 2 x 36 W > 40%
ExLin 7L-2 8,600 67 W > 127 2 x 58 W > 40%
ExLin 10-2 11,230 89 W > 127 > 2 x 58 W > 40%

CEAG ExLin vs. x 36W Fluorescent

LED vs. fluorescent
savings at a glance

Why are so many

facilities making the 40% 66% 100%
switch from fluorescent
to LED?
The numbers say it all. 40% REDUCTION IN 66% LOWER TOTAL 100% LAMP MAINTENANCE
ENERGY COSTS COST OF OWNERSHIP REDUCTION
Assumptions: Calculations based on overall life of the LED system. Energy cost of €.09 per kilowatt; 24 hour per day operation;
labor rate of €75 each for 2 workers; average time for fixture maintenance of 2 hours.

1.2.2 EATON [Link]

 Why CEAG ExLin LED?
Safe, reliable, efficient. CEAG ExLin fixtures combine state-of-the-art LED technology with optimised
thermal management and a time-tested enclosure to extend service life in extreme environments.

10,000 lumen model now available!

Superior performance and efficiency Designed for reliability in the most demanding
• Replaces 2x18 W, 2x36 W and 2x58 W fluorescent fixtures, environments
as well as low bay fixtures over 150 W HID • Passed dynamic vibration test acc. EN60068-2-6
• Rated life of 100,000 hours at 25 ºC based on L90C5 • Passed windload test up to 316 km/h acc. EN60598-2-3
provides long term, low-maintenance operation • Fixture design optimised to avoid water condensation
• More then 132 lm/W provides up to 40 % energy efficiency inside the fitting
compared to traditional fluorescent fixtures
• Operating temperature from -40 ºC to +55 ºC State-of-the-art LED technology coupled with a long
history of hazardous area lighting design expertise
Optimised light distribution with optics and lens options • LED light strings operate independently. Should one
• Standard, narrow and wide beam optics optimise light string fail, all other strings will continue to work, avoiding
distribution, providing light where the customer needs it complete loss of illumination
with the potential to reduce the number of fixtures required • Enclosure material is time-tested and field-proven for
• Clear or diffused (frosted) lens available in glass provides durability in harsh and hazardous applications globally
application flexibility • Optimised thermal management for extending service life
• Optional laminated glass lens with extended plastic foil in extreme environments
prevents glass from falling - ideal for safe use in critical
processes in food and beverage, chemical and
pharmaceutical applications

Low profile and lightweight design with drop in mounting

compatibility to CEAG eLLK fluorescent
• Decreases footprint in confined applications and reduces
installation effort
• Same fixing point as eLLK 2x18 W fixtures and a mounting kit
available allowing for easy replacement of 2x36 W and 2x58 W
without changing cables

Large connection space and innovative terminal technology for

simple and quick electrical installation standard wide narrow
• The new 5-pole push-type terminals (optional) enable easy
connection of the cables and reduce the amount of work
required.

Emergency lighting function with central battery system

• Available with V-CG-S functionality. Safe and reliable lighting
via Eaton‘s central battery system.
• Each fixture can be set to 25%, 50% or 100% light output
in emergency lighting mode. This allows for optimization of
the battery capacity to provide a long duration of emergency
lighting.

[Link] EATON 1.2.3

 CEAG ExLin technical specifications:

Certifications and compliances:

IECEx / ATEX Standards:
EC-Type Examination Certificate
• BVS 18 ATEX E 037 X
IECEx-Certification of conformity
3L-1 and 5L-1 models 5L-2, 7L-2, 10L-2
• IECEx BVS 18.0028X models
Marking accd. to 2014/34/EU
• Ex II 2G Ex eb ib op is q IIC T4/T5 Gb LED system: Standard materials:
• Ex II 2D Ex tb op is IIIC T80/115°C Db • Light colour / CRI: • Fixture enclosure - Glassfibre
Marking accd. to IECEx 5000K / 70 and 80 CRI reinforced polyester
and 4000K / 80 CRI
• Ex eb ib op is q IIC T4 Gb • LED module cover - toughened glass or
• Optics: Standard, narrow beam, plastic-laminated glass, clear or opaque
• Ex tb op is IIIC T80/115°C Db wide beam.
Permissible ambient temperature, Fixture life (IEC 62722): Dimensions and weights:
depending on configuration LED ExLin 3L-1 and 5L-1
• -40°C up to +55°C* for ExLin 3L, 5L, 7L
• L90 ~100,000 h at ta = +25 °C • 770x201x115 mm
• -40°C up to +45°C* for ExLin 10L
• L85 ~75,000 h at ta = +55 °C • 6.7 kg
Degree of protection accd. to EN 60529
Control gear ExLin 5L-2, 7L-2 and 10L-2
• IP66/67
• C5 ~100,000 h at ta = +25 °C • 931x201x115 mm
IK-class according to IEC/EN 62262
• IK10 • C10 ~75,000 h at ta = +55 °C • 8.0 kg

* Up to +50°C for 3L-1and 5L-2 with through wiring and plastic cable glands. Up to +45°C for 5L-1 and 7L-2 with through wiring and plastic cable glands.

Electrical ratings:
Model ExLin 3L-1 ExLin 5L-1 / 5L-2 ExLin 7L-2 ExLin 10L-2
** Voltage for
Voltage** 110 up to 277 V AC/DC 110 up to 277 V AC/DC 110 up to 277 V AC/DC 220-277 V AC/DC V-CG-S models:
220-254 V AC / 195-250 V DC
Power consumption 22 W 44 W 67 W 88 W
Lumens (clear glass cover) † 2910 lm 5610 / 5810 lm 8600 lm 11230 lm † Lumen values apply to
5000 K light colour, 70 CRI
Lumens (frosted glass cover) † 2490 lm 4940 / 4960 lm 7370 lm 9900 lm fixtures. Lumen output may
vary slightly for different
Frequency 0/50 - 60 Hz 0/50 - 60 Hz 0/50 - 60 Hz 0/50 - 60 Hz models.
Inrush current 5 A for 1 ms 5 A for 1 ms 9 A for 1 ms 9 A for 1 ms
Power factor cos ϕ @ 230 V ≥ 0.92 ≥ 0.95 ≥ 0.95 ≥ 0.98
Circuit EVG EVG EVG EVG
Protection class I I I I
Immunity to surge voltages
4 kV, L-N and L-PE 4 kV, L-N and L-PE 4 kV, L-N and L-PE 4 kV, L-N and L-PE
according to EN6100-4-5

THD @230V 8% 5% 5% 5%

1.2.4 EATON [Link]

Catalog Numbering System:
Part number example
ExLin 5L-1 G C S 7 50 T1 1/6 M25K
CEAG ExLin linear, 5300 lumens, glass lens, clear lens, standard light beam, >70 CRI, 5000K, Type 2410-4 terminals, single-ended wiring, M25 plastic cable gland

ExLin 5L-1 G C S 7 50 T1 1/6 M25K

Version / LED modules
CCT Cable gland / thread
3L-1 2750 lm single sided
30 3000 K M25K M25 plastic glands
5L-1 5300 lm single sided
40 4000 K M20M M20 metallic threads
5L-2 5480 lm double sided
50 5000 K M25M M25 metallic threads
7L-2 8120 lm double sided
CRI Through wiring
10L-2 10600 lm double sided
7 >70 1/6 Single-ended
.Emergency light function
8 >80 2/6 Twin-ended
BLANK Standard, without em. Lighting
Terminals
V-CG-S with V-CG-S functionality*
Light distribution T1 Type 2410-4 max 6 mm2
NE+ see page 1.2.8
S Standard T3 Push-type 5-pole max 4 mm2
Protective cover material
N Narrow beam XX On request
G Glass
W Wide beam
Glass laminated with
F R Stray ligth protection grid * Not available for 10L-2
splitter protection foil

Protective cover type Additional terminal, CCT and CRI

options available. Please consult
C Clear factory or authorized Eaton‘s
Crouse-Hinds Division sales
F Opaque (Frosted) representative.

Example: Order-No.: Example Order-No.: Example:

ExLin 5L-1 G C S 7 50 T1 1/6 M25K Key 12300 1 4 0 101 ExLin description
ExLin 3L-1 xxxxx x 2 x xxx
ExLin 5L-1 xxxxx x 4 x xxx xxxxx x 4 x xxx 5300lm single sided
ExLin 5L-2 xxxxx x 5 x xxx

ExLin 7L-2 xxxxx x 7 x xxx

ExLin 10L-2 xxxxx x 9 x xxx

ExLin G 12300 x x x xxx 12300 x x x xxx Standard, glass cover

ExLin F 12301 x x x xxx
ExLin V-CG-S G 12310 x x x xxx
ExLin V-CG-S F 12311 x x x xxx

ExLin CS xxxxx x x 0 xxx xxxxx x x 0 xxx Clear cover, standard light beam
ExLin CN xxxxx x x 1 xxx
ExLin CW xxxxx x x 2 xxx
ExLin CR xxxxx x x 4 xxx
ExLin FS xxxxx x x 5 xxx
ExLin FN xxxxx x x 6 xxx
ExLin FW xxxxx x x 7 xxx

ExLin 750 xxxxx 1 x x xxx xxxxx 1 x x xxx CRI >70, CCT 5000 K
ExLin 740 xxxxx 2 x x xxx
ExLin 850 xxxxx 3 x x xxx
ExLin 840 xxxxx 4 x x xxx

ExLin 1/6 M25K xxxxx x x x 101 xxxxx x x x 101 Single ended wiring with M25 plastic glands
ExLin 2/6 M25K xxxxx x x x 103
ExLin 1/6 M20M xxxxx x x x 109

ExLin 2/6 M20M xxxxx x x x 111

ExLin 1/6 M25M xxxxx x x x 609
ExLin 2/6 M25M xxxxx x x x 611

[Link] EATON 1.2.5

 Why CEAG ExLin NE+ LED?
Safe, reliable, efficient. CEAG ExLin NE+ emergency light fittings combine environmentally friendly
batteries and state-of-the-art LED technology with optimised thermal management and a time-
tested enclosure to extend service life in extreme environments. Installation and maintenance
efforts are significantly reduced thanks to the innovative battery design.

ExLin NE+ available in 3L and 5L version

Emergency light fittings with a self-contained battery system Reliable emergency lighting
• Decentralized solution for the mandatory emergency lighting • In order to achieve the minimum operating time required for
in case of power failure via highly efficient LiFePO4 1) ensure a the emergency lighting mode, the power consumption and
safe and reliable illumination acc. EN EN 60598-2-22 consequently the illuminance is reduced. ExLin NE+ can
vary the power consumption of the entire LED module in
• ExLinNE+ is available as 3L or 5L and delivers appr. 2000 lm / emergency lighting modus via their electronics. This enables
1000 lm 2) for 1.5 h / 3 h in emergency mode homogeneous illumination of escape routes in accordance
with the local conditions, even in the emergency lighting
• Emergency lighting cycle can be set locally for 1.5 or 3 hour mode.
Reliable performance in harsh and hazardous environments • Selection of standard, narrow and wide beam optics ensures
• Temperature range extended significantly: extremely wide ideal illumination according to specific environments and
operating ambient temperature range of -40 °C to +45 °C applications
with almost homogeneous luminous efficacy

• Improved charging capabilities ensure a more stable and

robust charging cycle, thus resulting in longer lifetime

• LiFePO4 1) battery has no memory effect and a more stable

capacity for emergency lighting compared to standard NiCd 3)
batteries

Tests acc. DIN EN 50172 and clear visualisation

• The luminaires have integrated monitoring software that
monitors the functions of the luminaire and performs the
prescribed function tests and quarterly, partial duty-cycle test
in accordance with DIN EN 50172 and DIN V VDE 0108-100-1
automatically

• 2 diode LED display shows charge and battery status of the

luminaire
standard wide narrow
Simplified installation and maintenance in the Ex area
• Longer storage without recharging compared to NiCd ³)
possible

• LiFePO4 1) batteries do not require charging cycle for first

conditioning like NiCd 3), so that emergency lighting is
quicker fully available
1
) Lithium-Iron-Phosphate
• Hot Swap technology allows an easy exchange of the 2
) ExLin NE+ 3L/5L, GCS 750
battery in the Ex area without disconnecting the power temporary measurement
supply 3
) Nickel-Cadmium

1.2.6 EATON [Link]

CEAG ExLin NE+ technical specifications:

Certifications and compliances:

IECEx / ATEX Standards:
EC-Type Examination Certificate
• BVS 18 ATEX E 037 X
IECEx-Certification of conformity
• IECEx BVS 18.0028X Typ 3L-1 and 5L-1
Marking accd. to 2014/34/EU
• Ex II 2G Ex eb ib mb op is q IIC T4/T5 Gb
• Ex II 2D Ex tb op is IIIC T80/115°C Db LED system: Standard materials:
Marking accd. to IECEx • Light colour / CRI: • Fixture enclosure - Glassfibre
5000 K / 70 and 80 CRI reinforced polyester
• Ex eb ib mb op is q IIC T4 Gb
and 4000 K / 80 CRI
• Ex tb op is IIIC T80/115°C Db • LED module cover - toughened glass or
• Optics: Standard, narrow beam, plastic-laminated glass, clear or opaque
Permissible ambient temperature, depending wide beam.
on configuration
• -40 °C up to +45 °C* for Battery set Dimensions and weights:
ExLin NE+ 3L, 5L,
• LiFePO4 with LED display and ExLin 3L-1 and 5L-1
specified data 0 °C up to +45 °C monitoring by micro processor
• 770x201x115 mm
Degree of protection accd. to EN 60529
• 8.3 kg
• IP66/67
Fixture life (IEC 62722):
IK-class according to IEC/EN 62262
LED
• IK10
• L90 ~100,000 h at ta = +25 °C
* Up to +40 °C with through wiring.
• L85 ~75,000 h at ta = +55 °C
Control gear
• C5 ~100,000 h at ta = +25 °C
• C10 ~75,000 h at ta = +55 °C

Electrical ratings:
Model ExLin 3L-1 NE+ ExLin 5L-1 NE+

Voltage 110 up to 254 V AC 110 up to 254 V AC

Power consumption Ø 23 W 45 W
Lumens (clear glass cover) † 2910 lm 5610 lm
Lumens (frosted glass cover) † 2490 lm 4940 lm
2000 lm (1.5 h) 2000 lm (1.5 h)
Lumens in emergency mode †
1000 lm (3 h) 1000 lm (3 h)
Frequency 50 - 60 Hz 50 - 60 Hz
Inrush current 5 A for 1 ms 5 A for 1 ms
Power factor cos ϕ @ 230 V ≥ 0.92 ≥ 0.95
Circuit EVG EVG
Protection class I I
Immunity to surge voltages
4 kV, L-N and L-PE 4 kV, L-N and L-PE
according to EN6100-4-5

THD @230V 8% 5%

† Lumen values apply to

5000K light colour, 70 CRI
fixtures. Lumen output may
vary slightly for different
models.

[Link] EATON 1.2.7

CEAG ExLin NE+ partnumber system:
Part number example
ExLin 3L-1 NE+ G C S 7 50 T1 1/6 M25K
CEAG ExLin linear, 5300 lumens, glass lens, clear lens, standard light beam, >70 CRI, 5000K, Type 2410-4 terminals, single-ended wiring, M25 plastic cable gland

ExLin 3L-1 NE+ G C S 7 50 T1 1/6 M25K

Version / LED Module
CCT Cable gland / thread
3L-1 2910 lm single sided
30 3000 K** M25K M25 plastic glands
5L-1 5610 lm double sided
40 4000 K M20M M20 metallic threads

Emergency light function 50 5000 K M25M M25 metallic threads

NE+ with selfcontained battery Through wiring

CRI 1/6 Single-ended

Protective cover material
7 >70 2/6 Twin-ended
G Glass
8 >80 Terminals
Glass laminated with
F
splitter protection foil T1 Type 2410-4 max 6mm2
Light distribution
Protective cover type Push-type
S Standard T3 5-pole
C Clear
max 4 mm²
N Narrow beam
F Opaque (Frosted) XX On request
W Wide beam
Additional terminal, CCT and CRI
R With stray light protection grid options available. Please consult
factory or authorized Eaton‘s
Crouse-Hinds Division sales
representative

** on request

Example: Order-No.: Example Order No.: Example:

ExLin 3L-1 NE+ G C S 7 50 T1 1/6 M25K Key 12320 1 2 0 101 ExLin description
NE+
ExLin 3L-1 xxxxx x 2 x xxx xxxxx x 2 x xxx
ExLin 5L-1 xxxxx x 4 x xxx 5300 lm single sided

ExLin NE+ G 12320 x x x xxx 12320 x x x xxx Standard, glass cover

ExLin NE+ F 12321 x x x xxx

ExLin CS xxxxx x x 0 xxx xxxxx x x 0 xxx Clear cover, standard light beam

ExLin CN xxxxx x x 1 xxx

ExLin CW xxxxx x x 2 xxx
ExLin CR xxxxx x x 4 xxx
ExLin FS xxxxx x x 5 xxx
ExLin FN xxxxx x x 6 xxx
ExLin FW xxxxx x x 7 xxx

ExLin 750 xxxxx 1 x x xxx xxxxx 1 x x xxx CRI >70, CCT 5000 K
ExLin 740 xxxxx 2 x x xxx
ExLin 850 xxxxx 3 x x xxx
ExLin 840 xxxxx 4 x x xxx

ExLin 1/6 M25K xxxxx x x x 101 xxxxx x x x 101 Single ended wiring with M25 plastic glands

ExLin 2/6 M25K xxxxx x x x 103

ExLin 1/6 M20M xxxxx x x x 109
ExLin 2/6 M20M xxxxx x x x 111
ExLin 1/6 M25M xxxxx x x x 609
ExLin 2/6 M25M xxxxx x x x 611

1.2.8 EATON [Link]

CEAG ExLin / EXLin V-CG-S / ExLin NE+

Dimensions & Polar Curve:

Weight: CEAG ExLin / ExLin V-CG-S / ExLin NE+
standard optic with clear cover
CEAG ExLin / ExLin V-CG-S / ExLin NE+
standard optic with opaque cover

90 90
CEAG ExLin / ExLin V-CG-S 90 90

3L-1 and 5L-1: 75

75 75 75
100 100

60 60 60 60
200 200

45 45 45 300
45
300

30 30 30 30
400
15 400
15 15 15
0 0
C 0 C 0
C90 l/cd/klm C90 l/cd/klm

CEAG ExLin / ExLin V-CG-S / ExLin NE+ CEAG ExLin / ExLin V-CG-S / ExLin NE+
Weight: 6.7 kg wide beam narrow beam
90 90 90 90

CEAG ExLin / ExLin V-CG-S

75 75 75 75
5L-2, 7L-2 and 10L-2:
60 60 60 60

45 45 45 45
30 30 30 30
15 15 15 15
0 0
C 0 C 0
C90 l/cd/klm C90 l/cd/klm

Weight: 8.0 kg

CEAG ExLin NE+

3L-1 and 5L-1:

Gewicht: 8.3 kg

[Link] EATON 1.2.9

 Mounting Accessories (Order Separately)
Pipe Clamps
Ordering Code Description

2 2480 462 000 * 2 pcs. R12 (1 1/4”), Ø 38 - 42 mm with screws and polyamide washer, hot-dip galvanized

2 2480 472 000 * 2 pcs. R22 (1 1/2”), Ø 47 - 51 mm with screws and polyamide washer, hot-dip galvanized

2 2480 482 000 * 2 pcs. R32 (2''), Ø 56 - 60 mm with screws and polyamide washer, hot-dip galvanized

NOR 000 005 009 211 1 pcs. A8 (1 1/2") D 47 - 51 mm for AB 12.. with screws and polyamide washer, hot-dip galvanized

NOR 000 005 009 229 1 pcs. A9 (2") D 56 - 60 mm for AB 12.. with screws and polyamide washer, hot-dip galvanized

2 2480 550 010 2 pcs. Two-part, for pipe mounting LB 48 - FT with screws and polyamide washer, hot-dip galvanized

Fixing Accessories
Ordering Code Description

2 2480 550 013 2 pcs. luminaire mounting bracket with 30° angle, wall mounting LH 30 - FT, hot-dip galvanized

2 2480 550 014 2 pcs. luminaire mounting bracket with 45° angle, wall mounting LH 45 - FT, hot-dip galvanized

2 2480 000 122 2 pcs. wall mounting bracket with 30° angle, with screws and polyamide washer, hot-dip galvanized

NOR 000 005 009 196 1 pcs. wall bracket 45° with screws and polyamide washer, hot-dip galvanized

2 2483 027 000 1 pcs. wall bracket W 27, 15°, for pole-mounting fitting Ø 42 mm, hot-dip galvanized

2 2480 092 000 2 pcs. ceiling mounting bracket D 92 with screws and polyamide washer, stainless steel

2 2480 550 011 2 pcs. C-bracket for luminaire mounting LAB-C50 - ER, stainless steel

2 2480 054 000 2 pcs. hexagon screw M8 x 20 for luminaire mounting, with polyamide washer

2 2480 002 000 * 2 pcs. eye bolt M8 for luminaire mounting, hot-dip galvanized

2 2480 550 022 * 2 pcs. wall mounting bracket with adjustable angle (15° step)
Pole mounting adapter for ExLin 3L-1 and 5L-1 , 42-62 mm diameter, hot-dip galvanised
2 2300 050 004
Different pole mounting adapter on request.

* Also available in stainless steel. Consult factory for ordering code.

Metallic Cable Glands (Order Separately)

ADE-1F2
Metric
Thread Cable sealing Cable seaing
Catalog # Size Cable Types range - Min range - Max

ADE1M200NPN M20 2.8 5.5

Non-armoured,
ADE1M201NPN M20 Marine shipboard, 4.5 8.5
ADE1M202NPN M20 Type P, Tray cable 7.0 12.0
(armoured)
ADE1M203NPN M20 10.0 16.0

ADE-4F Cable sealing range

inner sheath
Cable sealing range
outer sheath Armor
Metric
Thread
Catalog # Size Cable Types Min. Max. Min. Max. Min. Max.

ADE4M200NPN M20 SWA, SWB, STA, 2.8 5.5 4.5 8.5 0.2 0.9
Braided marine
ADE4M201NPN M20 shipboard, Type P; Lead 4.5 8.0 7.0 12.0 0.2 0.9
ADE4M202NPN M20 sheathed cable (with 7.0 12.0 10.0 16.0 0.2 1.3
addition of earthing
ADE4M203NPN M20 washer) 10.0 15.5 13.5 21.0 0.2 1.3

ADE-1F2 and ADE-4F catalog numbers are for nickel-plated brass; For other material options, refer to our cable glands section within [Link]/en/

1.2.10 EATON [Link]

Adapter Kits for eLLK Retrofits (Order Separately)
CEAG ExLin LED fixtures are designed with the same fixing point as Crouse-Hinds series CEAG eLLK 2x18W fixtures, making
retrofits simple and cost-effective.

Adapter kits allow for easy replacement of 2x36W and 2x58W eLLK fixtures without changing already-installed cables or mounting
brackets. Adapter kits include a metal bar, junction box and connection cables between the juntion box and ExLin fixture.

Ordering Code Description

2 pcs. ExLin adapter kit for retrofitting to

See for yourself how easy it is to upgrade your
eLLK 2x36 W fixture - includes metal bar, junction
eLLK lighting installation to our state-of-the-art
2 2300 500 001
box, plastic glands and connection cable between ExLin LED solution!
box and fixture
1 pcs. ExLin adapter kit for retrofitting to
eLLK 2x58W fixture - includes metal bar, two
2 2300 500 002
junction boxes, plastic glands and connection
cable between boxes and fixture
1 pcs. ExLin mounting metal bar for retrofitting to
3 2300 500 001 eLLK 2x36 W fixture - without junction box and
connection cable
1 pcs. ExLin mounting metal bar for retrofitting to
eLLK 2x58W fixture - without junction box and
3 2300 500 002
connection cable - without junction box and
connection cable Visit [Link]/ellk-to-exlin to watch the fast and
simple retrofit process using our adapter kit

[Link] EATON 1.2.11

Eaton’s Crouse-Hinds, B-Line and Oil & Gas Division
The safety you rely on.
See the complete offering of hazardous and industrial products at [Link].

U.S. (Global Headquarters): Australia Korea The Netherlands

Eaton's Crouse-Hinds Phone +61-2-8787-2777 Phone +82-2-3484-6783 Phone +31-10-2452145
Business Fax +61-2-9609-2342 Fax +82-2-3484-6778 Fax +31-10-2452121
crousehindsanz@[Link] CCHK-sales@ CHRD_mail@[Link]
1201 Wolf Street
[Link]
Syracuse, NY 13208
China Norway
(866) 764-5454 Mexico/Latin America/
Phone +86-21-2899-3600 Phone +47-32-244600
FAX: (315) 477-5179 Caribbean
Fax +86-21-2899-4055 Fax +47-32-244646
FAX Orders Only: Phone +52-555-804-4000
ECHsales@[Link] CHLIoffice@[Link]
(866) 653-0640 Fax +52-555-804-4020
mxmercadotecnia@
CrouseCustomerCTR@[Link] Great Britain [Link] Singapore:
Phone +44-247-630-89 30 Phone +65-6645-9888
Fax +44-247-630-10 27 Fax +65-6297-4819
Spain
sales5@[Link] CHSI-Sales@[Link]
Phone +34-9-37362710
Fax +34-9-37835055
For more information: [Link]@ Turkey
India Phone +90-216-464-20-20
If further assistance is Phone +91-124-4683888 [Link]
Fax +90-216-464-20-10
required, please contact Fax +91-124-4683899 infoEGTurkey@[Link]
an authorized Eaton cchindia@[Link] Middle East (Dubai)
Phone +971-4-427-2522 / 2500
Distributor, Sales Office, Fax +971-4-429-8521 Russia
or Customer Service Canada Phone +7-495 510-24-27
Toll Free +1-800-265-0502 CHMEsales@[Link]
Fax +7-495 510-24-28
Department. Fax +1-800-263-9504 info@[Link]
Fax orders only: [Link]
+1-866-653-0645

Eaton’s Crouse-Hinds Division

Neuer Weg – Nord 49
D-69412 Eberbach

Phone +49 (0) 6271/806-500

Fax +49 (0) 6271/806-476
E-mail info-ex@[Link]
Internet [Link]

Changes to the products, to the information contained in this document, and to prices are
reserved; so are errors and omissions. Only order confirmations and technical documentation
Eaton by Eaton is binding. Photos and pictures also do not warrant a specific layout or functionality.
1000 Eaton Boulevard Their use in whatever form is subject to prior approval by Eaton. The same applies to
Cleveland, OH 44122 Trademarks (especially Eaton, Moeller, and Cutler-Hammer). The Terms and Conditions of
United States Eaton apply, as referenced on Eaton Internet pages and Eaton order confirmations.
[Link]

© 2021 Eaton Corporation Eaton’s Crouse-Hinds Division

All Rights Reserved 1201 Wolf Street Eaton is a registered trademark.
Printed in Germany Syracuse, NY 13208
Publication No. BR 300 8000 2297 (866) 764-5454 All other trademarks are property
Nov. 2022 CrouseCustomerCTR@[Link] of their respective owners.

1.2.12 EATON [Link]