TM

Brilliance CT 16/10/6-Slice Configuration

(water) V.2.2.1
Mx8000 IDT 16/10-Slice Configuration V4.2.1
Upgrade Instructions

4550 191 01302

Revision F

This document and the information contained in it is proprietary and confidential information of Philips Healthcare ("Philips") and may not be
reproduced, copied in whole or in part, adapted, modified, disclosed to others, or disseminated without the prior written permission of the Philips
Legal Department. Use of this document and the information contained in it is strictly reserved for current Philips personnel and Philips customers
who have a current and valid license from Philips for use by the customer’s designated in-house service employee on equipment located at the
customer’s designated site. Use of this document by unauthorized persons is strictly prohibited. Report violation of these requirements to the
Philips Legal Department. This document must be returned to Philips when the user is no longer licensed and in any event upon Philips’ first
written request.

© 2011 Koninklijke Philips Electronics N.V. All Rights Reserved.

CSIP Level 1
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Philips Healthcare
© 2011 KONINKLIJKE PHILIPS ELECTRONICS N. V. ALL RIGHTS RESERVED.

Warranty Disclaimer
PHILIPS PROVIDES THIS DOCUMENT WITHOUT WARRANTY OF ANY KIND, IMPLIED OR EXPRESSED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE.

Limitation of Liability
PHILIPS HAS TAKEN CARE TO ENSURE THE ACCURACY OF THIS DOCUMENT. HOWEVER, PHILIPS
ASSUMES NO LIABILITY FOR ERRORS OR OMISSIONS AND RESERVES THE RIGHT TO MAKE CHANGES
WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION, OR
DESIGN. PHILIPS MAY MAKE IMPROVEMENTS OR CHANGES IN THE PRODUCT(S) OR PROGRAM(S)
DESCRIBED IN THIS DOCUMENT AT ANY TIME.

Password Notice
THE PASSWORD IS THE PROPERTY OF PHILIPS HEALTHCARE AND IS PROVIDED FOR THE EXCLUSIVE
PURPOSE OF PROVIDING ACCESS TO SELECTED SERVICE UTILITIES WHICH ARE DESCRIBED IN THIS
SERVICE MANUAL AS BEING ASSOCIATED WITH THE PASSWORD. USE OF THIS PASSWORD FOR ANY
PURPOSE OTHER THAN FOR THE ACCESS TO THE SELECTED SERVICES UTILITIES IS STRICTLY
PROHIBITED.

4550 191 01302 © 2011 Koninlijke Philips Electronics N.V All Rights Reserved CSIP Level 1 ii
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Symbol Descriptions

! Attention symbol Radiation warning symbol

Laser warning symbol Biohazard warning symbol

Magnetism warning symbol Projectile warning symbol

Electrical warning symbol Do not touch

Crush warning symbol

4550 191 01302 © 2011 Koninlijke Philips Electronics N.V All Rights Reserved CSIP Level 1 iii
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Safety Information
To the User of This Manual
The user of this manual is directed to read and carefully review the instructions, warnings and cautions contained herein prior to beginning installation
or service activities. While you may have previously installed or serviced equipment similar to that described in this manual, changes in design,
manufacture or procedure may have occurred which significantly affect the present installation or service.

!
WARNING In addition to the warnings listed above, make sure to follow all safety guidelines as
described in the Safety Manual. Failure to do so can result in severe personal injury.
Installation and Environment
Except for installations requiring certification by the manufacturer per federal standards, see that a radiation protection survey is made by a qualified
expert in accordance with NCRP 102, section 7, as revised or replaced in the future. Perform a survey after every change in equipment, workload, or
operating conditions which might significantly increase the probability of persons receiving more than the maximum permissible dose equivalent.

Diagnostic Imaging Systems - Mechanical-electrical Warning

All of the moveable assemblies and parts of this equipment should be operated with care and routinely inspected in accordance with the
manufacturer’s recommendations contained in the equipment manuals.
Only properly trained and qualified personnel should be permitted access to any internal parts. Live electrical terminals are deadly; be sure line
disconnects are opened and other appropriate precautions are taken before opening access doors, removing enclosure panels, or attaching
accessories.
Do not under any circumstances, remove the flexible high tension cables from the x-ray tube housing or high tension generator and/or the access
covers from the generator until the main and auxiliary power supplies have been disconnected. Failure to comply with the above may result in serious
or fatal bodily injuries to the operator or those in the area.
Prior to any service and maintenance activities inside components:
Switch off the system at the main power supply (using the on-site On-Off switch), and the internal/external uninterruptible power supply (UPS).
Make sure that no other person can switch on power or switch off the security measures, when installation, maintenance or service work on the
system is performed.
Always use an ESD protection wrist strap when servicing any component in the system.

Electrical-grounding Instructions
The equipment must be grounded to an earth ground by a separate conductor. The neutral side of the line is not to be considered the earth ground.
On equipment provided with a line cord, the equipment must be connected to properly grounded, three-pin receptacle. Do not use a three-to-two pin
adapter.

4550 191 01302 © 2011 Koninlijke Philips Electronics N.V All Rights Reserved CSIP Level 1 iv
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Diagnostic Imaging Systems - Radiation Warning

X-ray and Gamma-rays are dangerous to both operator and others in the vicinity unless established safe exposure procedures are strictly observed.
The useful and scattered beams can produce serious or fatal bodily injuries to any persons in the surrounding area if used by an unskilled operator.
Adequate precautions must always be taken to avoid exposure to the useful beam, as well as to leakage radiation from within the source housing or
to scattered radiation resulting from the passage of radiation through matter.
Those authorized to operate, participate in or supervise the operation of the equipment must be thoroughly familiar and comply completely with the
current established safe exposure factors and procedures described in publications, such as: Subchapter J of Title 21 of the Code of Federal
Regulations, "Diagnostic X-ray Systems and Their Major Components", and the national council on radiation protection (NCRP) no. 102, "Medical X-
ray And Gamma-ray Protection For Energies Up To 10 Mev-equipment Design and Use", as revised or replaced in the future.
Those responsible for planning of x-ray and gamma-ray equipment installations must be thoroughly familiar and comply completely with NCRP no.
49, "Structural Shielding Design and Evaluation For Medical Of X-rays and Gamma-rays of Energies Up to 10 Mev", as revised and replaced in the
future. Failure to observe these warnings may cause serious or fatal bodily injuries to the operator or those in the area.
Add additional safety information as needed.

4550 191 01302 © 2011 Koninlijke Philips Electronics N.V All Rights Reserved CSIP Level 1 v
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Revision History
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Revision History

ECO # Revision Date Comments

H3001277 A March 2008 New Release

Added step to Reset the IBox in IBox Programming Procedure on page 166
Added CIRS Software Installation on a Single Server (Vertical Server) Configuration
H3001559 B June 2008
on page 118
Modified Full CIRS Software Installation on a Two Server Configuration on page 101

H3002128 C January 2009 Added Installing the CDR/MPR Fix 2.2.1/4.2.1 14021 CD on page 49

Time, Manpower and Main Steps on page 11 for the IRS upgrade was changed
Screen captures added to V2.2.1/4.2.1 Upgrade General Information on page 2
Modified Recording Network Settings on page 17, Restore the Network Configuration
on page 33, Installing COTS/Security Components on page 41, Installing the
Supplemental (Version) CD on page 44, Post Host Installation on page 57, License
Key Installation on page 63, Changing HIS/RIS Restrictions on page 82, Remote
H3002338 D May 2009
Recon Option Upgrade on page 83, CIRS Software Installation on a Single Server
(Vertical Server) Configuration on page 118, System Calibrations and Performance
Verifications on page 126, IBox Flash Upgrade on page 174
Deleted “Restoring License key from V2.0.2 Only” and “Appendix J: UPS Driver
Installation with EFFEKKTA MH 3000 Model”
Updated Deleting RAW Data from the IRS on page 87

Correction of the part number for 16-slice Supplemental V2.2.1.14009 CD

Addition of 6-slice Supplement CD and 6-slice AddOn CD (see Brilliance CT (Water—
CIRS) 6/10/16 V2.2.1 Software Kit on page 4)
Edited Brilliance CT (water) V2.2.1/MX8000 IDT V4.2.1 Upgrade Kit Contents on
page 3 and Software CD Kits on page 4
H3002868 E October 27, 2010 Warning edited in Protocol Conversion on page 71 and added to Overview on page 1
Changed procedure for enabling 0.42 rotation. This includes:
• Changed to Prerequisites on page 9
• Changed License Key Installation on page 67
• Change to System Calibrations and Performance Verifications on page 126
• Added Enabling 0.42 Sec. Rotation Speed for Rotor Balancing on page 194

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 vi
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Revision History
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

ECO # Revision Date Comments

Modified Brilliance CT (Water—CIRS) 6/10/16 V2.2.1 Software Kit on page 4

Modified Installing the Supplemental (Version) CD on page 44
E-012579 F Sept 15, 2011 Added Installing the Supplemental CD (for Brilliance 6-Slice with CIRS Only) on page
51
Modified Add-on and Test Raws Installation on S1 Server on page 124

This document was prepared by the CT BU Service Innovations Department.

For any additions, corrections, or suggestions, contact your CT BU Customer Support Department.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 vii
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
Brilliance CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F
TM

Contents
Revision History ............................................................................................................................. vi

Overview ......................................................................................................................................... 1
Important Safety Information.................................................................................................................................. 2
V2.2.1/4.2.1 Upgrade General Information ............................................................................................................ 2
Brilliance CT (water) V2.2.1/MX8000 IDT V4.2.1 Upgrade Kit Contents.......................................................... 3
Software CD Kits .............................................................................................................................................. 4
Brilliance CT (Water—CIRS) 6/10/16 V2.2.1 Software Kit .......................................................................... 4
Brilliance CT (Water—IRS) 6/10/16 V2.2.1 Software Kit............................................................................. 5
Mx8000 IDT (CIRS) 6/10/16 V4.2.1 Software Kit ........................................................................................ 7
Mx8000 IDT (IRS) 10/16 V4.2.1 Software Kit.............................................................................................. 8
Prerequisites .......................................................................................................................................................... 9
Relevant Documents (Available at the InCenter)............................................................................................ 10
Required Tools..................................................................................................................................................... 10
Time, Manpower and Main Steps ........................................................................................................................ 11

V2.2.1/4.2.1 Host Software Installation ......................................................................................... 12

Backup Procedure................................................................................................................................................ 12
Backup System Parameters ........................................................................................................................... 12
Recording Network Settings ........................................................................................................................... 17
Acquiring the Domain or Workgroup ......................................................................................................... 17
Acquiring the IP Address and Link Speed Settings................................................................................... 18
Acquiring the Proxy Settings ..................................................................................................................... 23
Acquiring the Gantry Positions .................................................................................................................. 24
Acquiring the Default Storage Device from the Preferences..................................................................... 24
Acquiring the Varian RPM ......................................................................................................................... 26
Collect Windows Network Paper Printer Configuration Settings.......................................................................... 27
Host Software Installation Instructions ................................................................................................................. 30
Before Installing the Host Software ................................................................................................................ 30

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 viii
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
Brilliance CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F
TM

Contents
Host OS Installation ........................................................................................................................................ 30
Restore the Network Configuration................................................................................................................. 33
Verifying and Changing EOD drive letter........................................................................................................ 37
Installing the Host Application Software............................................................................................................... 39
Installing the Supplemental CD ...................................................................................................................... 39
Installing COTS/Security Components ........................................................................................................... 41
Installing the IRS Addon on Host PC (only for systems with IRS) .................................................................. 42
Installing Host Software .................................................................................................................................. 43
Installing the Supplemental (Version) CD....................................................................................................... 44
Installing HOTFIX KB928388.......................................................................................................................... 46
Installing BR IDT Supplemental...................................................................................................................... 47
Installing the CDR/MPR Fix 2.2.1/4.2.1 14021 CD......................................................................................... 49
Installing the Supplemental CD (for Brilliance 6-Slice with CIRS Only).......................................................... 51
Restoring Computer Name and Domain/Workgroup Settings ........................................................................ 53
Setting the K2D Visa....................................................................................................................................... 54
Verifying and Set the Time and Date.............................................................................................................. 56
Post Host Installation ........................................................................................................................................... 57
Configuring the Host Dual Monitor Settings.................................................................................................... 57
Configuring the Host Monitor Refresh Rate.................................................................................................... 59
With Dual Monitors .................................................................................................................................... 59
With a Single Monitor Installation .............................................................................................................. 59
Exceed Configuration ..................................................................................................................................... 60
Acrobat Reader and CesarFTP Initialization .................................................................................................. 61
Configuring Administrative Tools Security Features....................................................................................... 61
SnagIt Configuration ....................................................................................................................................... 62
Restoring System Files................................................................................................................................... 65
License Key Installation .................................................................................................................................. 67
Overview ................................................................................................................................................... 67
Obtaining the License Key from the Philips Medical Website ................................................................... 67
Installing LIcense Key ............................................................................................................................... 69
Protocol Conversion ....................................................................................................................................... 71
Correcting Corrupted Protocols After Protocol Conversion....................................................................... 73
4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 ix
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
Brilliance CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F
TM

Contents
Protocol Correction Example..................................................................................................................... 74
Restore Varian RPM™ Settings ..................................................................................................................... 75
Windows Network Paper Printer Installation................................................................................................... 76
Set the Default Network Paper Printer ...................................................................................................... 78
Restore Custom Hospital Logo....................................................................................................................... 79
Verify the Gantry Position ............................................................................................................................... 81
Restoring Default Storage Device .................................................................................................................. 81
Changing HIS/RIS Restrictions....................................................................................................................... 82
Checking the IBox Software Version .............................................................................................................. 83
Remote Recon Option Upgrade ..................................................................................................................... 83

Foreign Language Installation Instructions .................................................................................. 84

Installing the IRS Operating System ............................................................................................. 87

Deleting RAW Data from the IRS......................................................................................................................... 87
Modifying Drive Letters ................................................................................................................................... 91
Windows NT Installation....................................................................................................................................... 93
Installing the Supplemental CD on the IRS.......................................................................................................... 94
Drive Letters Modification..................................................................................................................................... 95
Installing the IRS Software................................................................................................................................... 97
Installing the IRS Test Raws ................................................................................................................................ 98
Installing Add-On BR/IDT Supplemental on the IRS.......................................................................................... 100
Time Sync..................................................................................................................................................... 100

Full CIRS Software Installation on a Two Server Configuration .................................................. 101

Before Installation .............................................................................................................................................. 101
Check for a Service Partition ........................................................................................................................ 101
Install Service Partition ................................................................................................................................. 102

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 x
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
Brilliance CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F
TM

Contents
Install Software................................................................................................................................................... 103
Configure S2 ...................................................................................................................................................... 104
Configure S1 ...................................................................................................................................................... 110
Two Server Configuration Setting ...................................................................................................................... 117

CIRS Software Installation on a Single Server (Vertical Server) Configuration ........................... 118
Installing the Software........................................................................................................................................ 119
Configure S1................................................................................................................................................. 120
Single Server Configuration Setting.............................................................................................................. 123

Add-on and Test Raws Installation on S1 Server ......................................................................... 124

System Calibrations and Performance Verifications ................................................................... 126

Backup System Parameters............................................................................................................................... 127
Final Checks ...................................................................................................................................................... 128

Installing FCO 72800440 ............................................................................................................... 129

Downloading the ISO File for FCO 72800440 from the InCenter....................................................................... 129
Creating the Utility CD........................................................................................................................................ 130
Create a CD using Roxio Easy CD Creator.................................................................................................. 130
Create a CD using Sonic ............................................................................................................................. 131
Installing the IDT Supplemental (Pediatric Filter Change) CD .......................................................................... 132

Appendix A: Application Release Notes ...................................................................................... 134

Brilliance (Water-Cooled) Version 2.0.2 and Mx8000 IDT V4.02
Application Release Notes ................................................................................................................................. 134
New Features ............................................................................................................................................... 134
Work Flow ............................................................................................................................................... 135

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 xi
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
Brilliance CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F
TM

Contents
Easy protocols......................................................................................................................................... 138
Bolus Tracking Enhancements................................................................................................................ 138
Pulmonary Gating Option ........................................................................................................................ 138
Cardiac Irregularities (R Tag Correction) in Retrospective Tagging........................................................ 139
Cardiac Adaptive Filter ............................................................................................................................ 139
Adaptive Filter ......................................................................................................................................... 139
Recon Image Enhancement.................................................................................................................... 139
Shifted CT scale ...................................................................................................................................... 139
Issues fixed in Brilliance V2.0.2/4.0.2 ........................................................................................................... 140
Scanner Operation Cautions and Warnings ................................................................................................ 142
Open Issues.................................................................................................................................................. 143
Guidelines and Operation Instructions .................................................................................................... 143
Common IRS (CIRS) Guidelines............................................................................................................. 145
Application Limitations............................................................................................................................. 145
Brilliance (water-cooled) Version 2.2.1 and Mx8000 IDT V4.2.1
Application Release Notes ................................................................................................................................. 148
New Features in Brilliance 2.2.1 ................................................................................................................... 148
Cardiac .................................................................................................................................................... 148
New Filters (applicable only for system with CIRS)................................................................................. 149
mA and mAs Values................................................................................................................................ 149
Bolus Pro Automatic ROI Graphic Improvement..................................................................................... 150
A New Surview Mode .............................................................................................................................. 150
Force Max FOV in Detailed and UH Resolutions .................................................................................... 150
New GUI in Plan VIEWER....................................................................................................................... 150
Minimum Delay in Timed Scan................................................................................................................ 150
Scanner Operation Cautions and Warnings ................................................................................................. 151
Open Issues.................................................................................................................................................. 152
General.................................................................................................................................................... 152
Scanning ................................................................................................................................................. 152
Plan on Surview ...................................................................................................................................... 153
Archive .................................................................................................................................................... 153
Bolus Tracking......................................................................................................................................... 153
Interventional CCT .................................................................................................................................. 153

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 xii
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
Brilliance CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F
TM

Contents
Pulmo ...................................................................................................................................................... 154
Cardiac .................................................................................................................................................... 154
Preferences ............................................................................................................................................. 155
TLCT ....................................................................................................................................................... 155
Viewing and Filming ................................................................................................................................ 155
Common IRS (CIRS) Guidelines............................................................................................................. 156

Appendix B: Service Release Notes ............................................................................................. 157

Set User Mode Workaround............................................................................................................................... 158
Synchronizing CANpro with Host Computer ...................................................................................................... 159

Appendix C: IBox Software Upgrade ............................................................................................ 161

IBox Driver Verification....................................................................................................................................... 161
Installing the IBox Driver .................................................................................................................................... 162
Programming IBox FPGA Upgrade from V1.2.5/V3.2.5..................................................................................... 163
Installing the FPGA Files to the Laptop ........................................................................................................ 163
FPGA File Programming............................................................................................................................... 163
IBox Programming Procedure ...................................................................................................................... 166
Final Steps.................................................................................................................................................... 173
IBox Flash Upgrade ........................................................................................................................................... 174
IBox Software and FPGA Version Verification ................................................................................................... 176

Appendix D: Setting the Boot Devices ......................................................................................... 178

Appendix E: Change Host-IRS Connections Settings .................................................................. 179

Configure Remote Desktop Connections........................................................................................................... 179
Enable Supervisor service on S1 ....................................................................................................................... 180

Appendix F: Change HOST - CIRS IP Addresses ......................................................................... 181

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 xiii
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
Brilliance CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F
TM

Contents
Hospital LAN uses same IP addresses.............................................................................................................. 181
Change IP Addresses on the CIRS Servers ...................................................................................................... 181
CIRS Server Changes Final Steps ............................................................................................................... 184

Appendix G: Updating the Acquisition Device Driver .................................................................. 185

Appendix H: Manually Updating Acquisitor FPGA Programming ................................................. 186

Manually Updating the 3DBP Device Driver ...................................................................................................... 188
Manually Updating 3DBP FPGA Programming.................................................................................................. 189

Appendix I: Gantry Firmware Installation .................................................................................... 191

Gantry Firmware Installation .............................................................................................................................. 191
Check the Firmware Versions....................................................................................................................... 192

Appendix J: Enabling 0.42 Sec. Rotation Speed for Rotor Balancing .......................................... 194
Restore Calibrations (Partial Restore) ............................................................................................................... 201

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 xiv
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Overview
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Overview

IMPORTANT ! Read this section first before beginning the Upgrade Procedure.

This document details the upgrade procedures for Brilliance (water cooled) V2.2.1 / Mx8000 IDT V4.2.1 for systems
with CIRS/IRS from the following versions:
• Brilliance V1.2.5 or V2.0.2
• MX8000 IDT V3.2.5 or V4.0.2

IMPORTANT ! This document does not cover upgrade of MX8000 IDT V4.2.1 6-slice with vertical CIRS.

!
WARNING During the protocol conversion process, invalid converted protocol errors are saved
in a Protocol Conversion log file.
• Navigate to the Protocol Conversion log:
D:/SMI/SnagIt/conver_results_200x_xx_xx.txt (where xx is the date the log was
created) and review the problems encountered during conversion.
• It is the responsibility of the FSE to show all the invalid protocols to the chief
technician at the site and be corrected by the application specialist or site
technician.
Read and understand this document in its entirety before proceeding. The necessary instruction steps are:
• Host OS Installation on page 30
• Installing the IRS Operating System on page 87
or Full CIRS Software Installation on a Two Server Configuration on page 101
or CIRS Software Installation on a Single Server (Vertical Server) Configuration on page 118
• System Calibrations and Performance Verifications on page 126
• IBox Software Upgrade on page 161

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 1
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Overview
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

• EBW V2.0.62 for systems with CIRS configuration (see EBW V2.0.62 Software Installation Instructions supplied
with the Upgrade kit).

Important Safety Information

!
WARNING Prior to beginning any system installation or maintenance make sure that you are
familiar with all of the safety procedures in the Safety User Guide. If you don’t have a
copy you can download it from the InCenter. Failure to do so can result in severe
personal injury.

!
CAUTION Follow all guidelines for ESD Anti-static protection before performing any service procedure.

V2.2.1/4.2.1 Upgrade General Information

NOTE The upgrade kit is supplied with two software CD sets. One for systems with IRS and the other with systems with
CIRS. Verify and use the CD kit appropriate for your system type and remove the other CD kit from the site.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 2
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Overview
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Brilliance CT (water) V2.2.1/MX8000 IDT V4.2.1 Upgrade Kit Contents

Table 1: Brilliance CT V2.2.1/MX8000 IDT V4.2.1 Upgrade Kit

Description CIRS IRS

Upgrade Kit Checklist  

Release Notes  
FCO Document  
Software CD Kita  
Customer Letter  
CD Brilliance V2.0 CBT, Console  
CD Brilliance V2.0 CBT Visualization  
EBW V2.0.62 Upgrade Kitb  NA

a. See section Software CD Kits on page 4. Use the correct CD kit for your
system type.
b. The Upgrade software package includes EBW V2.0.62 software CD kit to
be used for upgrading the Remote Recon system (RRS) for customers
that have RRS installed. This kit includes the CDs and documentation.
Refer to the EBW V2.0.62 Installation Instructions manual delivered with
the kit for more details.

NOTE For customers migrating from MX8000 IDT V3.2.5, there is a Computer Based Training Kit with a Customer
Letter (P/N 4550 115 01361) that can be ordered.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 3
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Overview
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Software CD Kits
There are four different software kits depending on the system type.
• Brilliance CT (Water—CIRS) 6/10/16 V2.2.1 Software Kit on page 4
• Brilliance CT (Water—IRS) 6/10/16 V2.2.1 Software Kit on page 5
• Mx8000 IDT (CIRS) 6/10/16 V4.2.1 Software Kit on page 7
• Mx8000 IDT (IRS) 10/16 V4.2.1 Software Kit on page 8

Brilliance CT (Water—CIRS) 6/10/16 V2.2.1 Software Kit

Table 2: Brilliance CT (Water—CIRS) 6/10/16 V2.2.1 Software Kit (P/N 4550 113 01501)

Item P/N Description

1 4550 128 04541 BR40/64 Host OS V2.0.1.1

2 4550 128 99401 BR 16-slice Supplem. CD V2.2.1.14009

3 4550 128 99411 BR 10-slice Supplem. CD V2.2.1.14009

4 4550 128 99421 IDT/BR [Link] CD V2.2.0.4

5 4550 128 99431 IDT/BRHost V4.2.1.1925/2.2.1.1925

6 4550 128 04571 BRCT MX CIRS V4.2.4.13 (2 CDs)

7 4550 128 04591 BRCT MX CIRS Service V4.2.4.13

8 4550 128 99441 IDT/BR 16 CIRS AddOn V2.2.0.5

9 4550 128 99451 IDT/BR 10 CIRS AddOn V2.2.0.5

10 4550 128 99541 BRIDT Suppl.V2.2.1/4.2.1.14016

11 4535 674 26691 CD, Hotfix_KB928388_2.2.0.3

12 4550 127 01771 CDR/MPR Fix 2.2.1/4.2.1 14021

13 4550 127 01921 IDT/BR 6 Supplem.CDV2.2.1.14024

14 4550 127 01931 IDT/BR 6 CIRS Addon V2.2.1.1938

15 4550 128 99481 BR 6-slice Supplemental V2.2.1.14009

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 4
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Overview
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Brilliance CT (Water—IRS) 6/10/16 V2.2.1 Software Kit

Table 3: Brilliance CT (Water—IRS) 6/10/16 V2.2.1 Software Kit (P/N 4550 113 01413)

Item P/N Description

1 4550 128 04541 BR40/64 Host OS V2.0.1.1

2 4550 128 99401 BR 16-slice Supplem. CD V2.2.1.14009

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 5
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Overview
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Table 3: Brilliance CT (Water—IRS) 6/10/16 V2.2.1 Software Kit (P/N 4550 113 01413)

Item P/N Description

3 4550 128 99411 BR 10-slice Supplem. CD V2.2.1.14009

4 4550 128 99481 BR 6-slice Supplemental V2.2.1.14009

5 4550 128 99421 IDT/BR [Link] CD V2.2.0.4

6 4550 128 99431 IDT/BRHost V4.2.1.1925/2.2.1.1925

7 4550-128-01492 IRS OS V3.1.0

8 4550 128 99491 16-Slice IRS Add-on V4.2.0.1/[Link]

9 4550 128 99501 10-Slice IRS Add-on V4.2.0.1/[Link]

10 4550 128 99511 6-Slice IRS Add-on V4.2.0.1/[Link]

11 4550 128 99521 IRS SW V4.2.1.1100

12 4550 128 99541 BRIDT Suppl.V2.2.1/4.2.1.14016

13 4535 674 26691 CD, Hotfix_KB928388_2.2.0.3

14 4550 127 01771 CDR/MPR Fix 2.2.1/4.2.1 14021

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 6
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Overview
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Mx8000 IDT (CIRS) 6/10/16 V4.2.1 Software Kit

Table 4: Mx8000 IDT (CIRS) 6/10/16 V4.2.1 Software Kit (P/N 4550 113 01423)

Item P/N Description

1 4550 128 04541 BR40/64 Host OS V2.0.1.1

2 4550 128 99461 Supplemental 16-Slice V4.2.1.14009

3 4550 128 99471 Supplemental 10-Slice V4.2.1.14009

4 4550 128 99481 BR 6-slice Supplemental V2.2.1.14009

5 4550 128 99421 IDT/BR [Link] CD V2.2.0.4

6 4550 128 99431 IDT/BRHost V4.2.1.1925/2.2.1.1925

7 4550 128 04571 BRCT MX CIRS V4.2.4.13 (2 CDs)

8 4550 128 04591 BRCT MX CIRS Service V4.2.4.13

9 4550 128 99441 IDT/BR 16 CIRS AddOn V2.2.0.5

10 4550 128 99451 IDT/BR 10 CIRS AddOn V2.2.0.5

11 4550 128 99541 BRIDT Suppl.V2.2.1/4.2.1.14016

12 4535 674 26691 CD, Hotfix_KB928388_2.2.0.3

13 4550 127 01771 CDR/MPR Fix 2.2.1/4.2.1 14021

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 7
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Overview
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Mx8000 IDT (IRS) 10/16 V4.2.1 Software Kit

Table 5: Mx8000 IDT (IRS) 10/16 V4.2.1 Software Kit (P/N 4550 113 01433)

Item P/N Description

1 4550 128 04541 BR40/64 Host OS V2.0.1.1

2 4550 128 99461 Supplemental 16-Slice V4.2.1.14009

3 4550 128 99471 Supplemental 10-Slice V4.2.1.14009

4 4550 128 99421 IDT/BR [Link] CD V2.2.0.4

5 4550 128 99431 IDT/BRHost V4.2.1.1925/2.2.1.1925

6 4550 128 01492 IRS OS V3.1.0

7 4550 128 99491 16-Slice IRS Add-on V4.2.0.1/[Link]

8 4550 128 99501 10-Slice IRS Add-on V4.2.0.1/[Link]

9 4550 128 99521 IRS SW V4.2.1.1100

10 4550 128 99541 BRIDT Suppl.V2.2.1/4.2.1.14016

11 4535 674 26691 CD, Hotfix_KB928388_2.2.0.3

12 4550 127 01771 CDR/MPR Fix 2.2.1/4.2.1 14021

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 8
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Overview
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Prerequisites
1. Verify the kit contents according to the Kit Contents Check List.
• Brilliance CT (Water—CIRS) 6/10/16 V2.2.1 Software Kit (P/N 4550 113 01501) on page 4
• Brilliance CT (Water—IRS) 6/10/16 V2.2.1 Software Kit (P/N 4550 113 01413) on page 5
• Mx8000 IDT (CIRS) 6/10/16 V4.2.1 Software Kit (P/N 4550 113 01423) on page 7
• Mx8000 IDT (IRS) 10/16 V4.2.1 Software Kit (P/N 4550 113 01433) on page 8
2. Internet or phone access to CT Help Desk and authorization is required for obtaining the K2D Visa Entry as
described in Setting the K2D Visa on page 54. You must perform this step; the upgrade cannot be completed
without K2D Visa Entry.
3. EOD drive should be available for backup storage.
4. All images and BugRep Reports were backed up.
5. All the RAW data was reconstructed; it will be deleted
6. If used, a copy of the custom logo.
7. If used, the user name and password for the Varian RPM computer
8. If a Domain is used, a user name and password

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 9
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Overview
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Relevant Documents (Available at the InCenter)

Table 6: Relevant Documents

Title or Description

This document

BR CT IDT Calibration Procedure-Multiple Version available on the InCenter

BR CT IDT Performance Procedure-Multiple Version available on the InCenter

Required Tools

Table 7: Required Tools

Description (as appears on eSPF)

Standard FSE tool kit

FPGA Download kit (for Ibox only if it exists)

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 10
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Overview
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Time, Manpower and Main Steps

Table 8: Estimated Time and Manpower

Operation Estimated Time FSEs Total Manhours

Host software upgrade 2.5 hours

IRS/CIRS software upgrade

• IRS 1 hour

• CIRS 2 hours

IBox upgrade (if it exists) 30 minutes

Calibrations

• For 6/10 slice configuration when upgrading from V1.2.5/3.2.5 3 hours

• For 6/10/16 slice configuration when upgrading from V2.0.2/4.0.2 1 hour

Performance 1 hour

Total Time (aproximation)

• When upgrading from V1.2.5/3.2.5

For 6/10 slice IRS configuration 8 hours

For 6/10 slice CIRS configuration 9 hours

• When upgrading from V2.0.2/4.0.2

For 6/10 slice IRS configuration 6 hours

For 6/10 slice CIRS configuration 7 hours

• For EBW V2.0.62 Software Upgrade

2.5 hours
(if Remote Recon Option is installed)

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 11
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

V2.2.1/4.2.1 Host Software Installation

Backup Procedure
1. Perform a few scans in the different modes to ensure that the system is properly functioning.
2. If there is an IBox, verify the IBox is working properly.
3. Perform all necessary off-line reconstructions before the upgrade. During the Upgrade the old Raw data will be
deleted from the CIRS/IRS.
4. Backup all images and BugReps.

Backup System Parameters

Backup system parameters to an EOD disk as follows:
NOTE This process will not overwrite previously saved backups.
1. Log off and log on
• For upgrade from V1.25/3.25: log on as mxservice.
• For upgrade from V2.x/4.x: log on as philips_service.
2. Insert a formatted EOD into the drive.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 12
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

3. Insert the Supplemental CD. Refer to Table 9 on page 13 for the correct CD for your system.
Table 9: Brilliance CT Supplemental CD

Part Number Description

4550 128 99401 BR 16-slice Supplem. CD V2.2.1.14009 CD

4550 128 99411 BR 10-slice Supplem. CD V2.2.1.14009 CD

4550 128 99481 BR 6-slice Supplemental V2.2.1.14009 CD

4550 128 99461 Supplemental 16-Slice V4.2.1.14009 CD

4550 128 99471 Supplemental 10-Slice V4.2.1.14009 CD

4550 127 01921 IDT/BR 6 Supplem.CDV2.2.1.14024

NOTE If the Philips Install Wizard does not open automatically, on the desktop double-click My Computer and double-
click on the CD drive icon and then double-click the appropriate file for your system:
- Philips_MS_Brilliancexx_supplemental.msi.
- Philips_MS_IDTxx_supplemental.msi
(where xx is your system slice configuration).

If upgrading from V1.25/3.25 press Windows+D to access the desktop.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 13
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F
I

4. The Philips Install Wizard opens.

5. Select Backup and click Next, as shown in
Figure 1 on page 14.
The Backup/Restore dialog shown in Figure 3 on
page 15 opens.

Figure 1: Supplemental Window

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 14
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

NOTE The destination path for backup files must

be without any spaces in the file and path
name.
6. Click Browse shown in Figure 3 on page 15 and
select the destination path for backup (drive F:\—
the EOD drive), click OK, and then Start Backup.
7. When the backup is complete a message appears,
click OK as shown in Figure 2 on page 15.

Figure 2: Backup Done Prompt

Figure 3:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 15
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

8. Scroll up the log and look for errors in the Log

window shown in Figure 4 on page 16 (the Backup
Done message appears even if the backup was not
successful).
9. Click Close in the Log window.
10. Click exit in the Backup/Restore window shown in
Figure 3 on page 15.
11. Click Finish.
12. Eject the Supplemental CD.
13. Close all open windows.
14. Eject the EOD.

Figure 4:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 16
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Recording Network Settings

Acquiring the Domain or Workgroup

1. On the Host desktop right-click My Computer and click Properties.
2. Select the Computer Name tab.
3. Write the Full computer name and Workgroup name (see Figure 5) or Domain name (see Figure 6) mode in
Table 10 on page 17.

Figure 5: System Properties for Workgroup Figure 6: System Properties for Domain

NOTES • If a Domain is used contact IT to obtain a user name and password.

Table 10: Workgroup or Domain Values

Full Computer Name Workgroup Name Domain Name User Name Password

4. Click Cancel to close the System Properties window.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 17
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Acquiring the IP Address and Link Speed Settings

1. From the Desktop, right-click My Network Places
and select Properties.
The Network Connections window appears.
2. Right-click Hospital-LAN connection and select
Properties.
C
The hospital LAN Properties window opens
(Figure 7).
3. Select Internet Protocol (TCP/IP)(A) and click
Properties (B).
A

Figure 7: Hospital-LAN Properties Window

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 18
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

4. Write down the following information in Figure 8.

This is needed to verify the system was correctly
restored.
If Obtain an IP address Automatically or Obtain
DNS server address Automatically are selected
record this fact and proceed to the next step.

Setting Value
IP address
Subnet Mask
Default Gateway
Preferred DNS Server
Alternate DNS Server

5. Click Advanced (Figure 8).

Figure 8: Internet Protocol (TCP/IP) Properties Window

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 19
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

6. Select the WINS tab and record all (if any) the WINS
addresses and the LMHOST and NETBIOS settings
(Figure 9)
• WINS address ___________________
• ___________________
• ___________________
• LMHOST lookup Enabled/Disables
• NetBIOS over TCP/IP: Enabled _______
Disabled _______
Default_________
7. Click Cancel twice.
8. Do not close the Hospital-LAN Properties window.

Figure 9:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 20
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

9. Click Configure (C).

10. Click Yes on the "Do you wish to proceed?" message.
11. Click the Advanced tab (see Figure 11 or Figure 12 on
page 22).
C

Figure 10: Hospital-LAN Properties Window

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 21
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Figure 12: Dell 530: Media Type

Figure 11: Dell 650: Link Speed & Duplex
12. From the Property list, click Link Speed & Duplex (for Dell 650 Host (Figure 11)) or Media Type (for Dell 530
(Figure 12) and write the value in the Value field.
13. Link Speed: ____________________________
14. Click Cancel and close all windows.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 22
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Acquiring the Proxy Settings

1. If needed, press keyboard key combination Windows+D to open Windows Desktop.
2. Right-click the Internet Explorer icon, and select Properties. If the icon is not on the desktop, click Start >
Settings > Control Panel > Internet Options.
3. Select the Connections tab.
4. Click LAN Settings in the Internet Properties window (Figure 13) to open the LAN Settings window (Figure 14 on
page 24).

Figure 13: Internet Options (or Properties) Window

5. Record all check mark selections in the LAN Settings window (Figure 14).

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 23
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

6. Write the settings as they appear in the LAN Settings

window (Figure 14).

SETTING NAME ENABLED/DISABLED

Automatically detect settings

Use automatic configuration

script

Address: _______________

Use a proxy server for your LAN

Address: _______________

Port: ___________________

7. Click Cancel twice and close all windows.

Figure 14: LAN Settings Window

Acquiring the Gantry Positions

• When upgrading from V2.02/4.02, on the desktop double-click the Scanner Application icon; if you have a single
monitor click the Processing tab and in the Archive select
Preferences > Scanner Options > Set Gantry Position
and record the settings_____________________________________.
• For an upgrade from V1.25 / 3.25 select
Home > Utilities > Misc > Set Scanner Position and record the settings: ________________________. Click
Close.

Acquiring the Default Storage Device from the Preferences

1. Select the Default Storage Devices option.
• When upgrading from V2.02/4.02:
From the Scanner Options click Default Storage Devices and click the Default Storage Devices button.
4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 24
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

• For an upgrade from V1.25 / 3.25:

Select Default Storage Devices from the Misc. table.
2. Record the devices that are selected (marked in blue in Figure 15 on page 25):
 Local  CDR  _____________

 EOD  _____________

 _____________  _____________  _____________

 _____________  _____________  _____________

 _____________  _____________  _____________

 _____________  _____________  _____________

 _____________  _____________  _____________

Figure 15:

3. Click Cancel, for V1.25 / 3.25 skip Step 4 and continue with Step on page 26.
4. Click OK to close the Preferences window.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 25
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Acquiring the Varian RPM

If you have a Varian RPM, record the address to the mounted drive "V". Otherwise skip to the following Step 4 on page
26.

NOTE Make sure that the Varian RPM is turned on

and connected to the network. If it is not, you
will not see the mounted drive:
1. Connect the Varian RPM to the network
and turn it on.
2. Restart the CT Host computer Figure 16: Varian drive Share Name
3. Log on as philips_service.
1. Press keyboard key Windows + D. The windows desktop appears and double-click My Computer.
2. Record the V: drive share name for the folder and IP address and share folder name
values ________________________. See Figure 16 on page 26 for an example of a V: drive).
3. Close My Computer.
4. If you have a custom logo for reporting make sure you have a copy or ask the customer for a copy.
NOTE If necessary ask the hospital administration to provide the custom logo.
5. Close all windows.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 26
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Collect Windows Network Paper Printer Configuration Settings

NOTE If you do not have a paper printer skip to section Host Software Installation Instructions on page 30.
Using the following procedure write down the settings for the Network Windows paper printers to be connected to the
Host computer.

1. Press the “WIndows” key and then click Start >

Settings > Printers and Faxes.
2. The Printers and Faxes window appears. Right-click
the windows paper printer in the Printer name list and
select Properties.
3. Write down the following information:
• Name___________________
• Location________________
• Comment_______________
• Model__________________
4. Click the Ports tab.

Figure 17:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 27
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

5. Highlight the IP port and click Configure Port.

Figure 18:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 28
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

6. Write down the following values:

• Port name___________________________
• Printer name or IP address______________
• Protocol____________________________
• RAW Settings Port Number _____________
SNMP Status Enabled:
• Community name_____________________
• SNMP Device Index___________________
7. Click Cancel twice and close the Printer and Fax
window.

Figure 19:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 29
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Host Software Installation Instructions

Before Installing the Host Software

1. Disconnect the Host computer from the hospital’s network! Note the message in the system tray - HOSPITAL LAN
DISCONNECTED.
If the Remote Recon option is installed, disconnect the network cable between the CIRS and the EBW.
NOTE During the installation, drive D: will be formatted. Before starting the installation procedure verify that all
important images have been backed up. The RAW data will be lost. Confirm with the customer that is it OK to
delete it.
2. Press and release the Emergency Stop button on the Scan Control Box.
3. Eject any EOD cartridges that may be in the EOD drive.
4. Disconnect any USB/Firewire storage devices (USB memory drive, external hard drive, etc.)

Host OS Installation
Host OS installation procedure takes approximately 55 minutes.
If the Host installation fails during the installation restart the Host Installation procedure.
1. Verify correct CD is used for this installation.

Part Number Description

4550 128 04541 BR40/64 Host OS V2.0.1.1

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 30
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

2. Insert the CD labeled BR40/64 Host OS V2.0.1.1.

3. Log off and restart the system. The boot menu appears.
4. Type 1 in Figure 20 on page 31.

Figure 20:
The next Installation menu opens.

Patient data will be lost!!!.

1) Proceed with full installation and lose patient data.
2) Go to Custom Installation and preserve patient data.
[1,2]?

Figure 21:
5. Type 1 (see Figure 21 on page 31) and press Enter. The host reboots and drives C and D are formatted; all data is
lost and Windows XP installation copies the installation files to the hard drive.
Windows XP installation now copies the installation files to the hard drive. This takes approximately 10-15 minutes.
The system automatically reboots when complete.
6. When prompted, eject the BR40/64 Host OS V2.0.1.1 CD from the drive. Press CTRL+ALT+DEL to restart the
computer. The Host computer restarts and the Windows XP installation continues automatically for about 40 more
minutes. During this process, the Host computer is automatically restarted several times.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 31
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

NOTE Ignore the dialog box that asks to restart the

computer.

NOTE Be patient. Do not touch the keyboard or

mouse until the message as in Figure 22 on
page 32 appears.
7. When the OS installation is complete and the message
in Figure 22 on page 32 appears, click OK.

Figure 22:
8. Connect the Host computer to the hospital’s network!
If the Remote Recon option is installed, connect the network cable between the CIRS and the EBW.
9. On the Desktop, right-click My Network Places and select Properties.
10. Verify that two network cards are installed with no errors: Hospital LAN and Host-IRS Connection.
NOTE Do not close the window.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 32
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Restore the Network Configuration

Manually configure the Network identification information as follows:

1. Right-click the “Hospital LAN” network card and

select Properties.
2. Double-click Internet Protocol (TCP/IP).
3. Select the options and type the information recorded
in Step 4 on page 19.
• IP Address
• Subnet Mask
• Default Gateway
• Primary DNS
and/or
• Secondary DNS.
4. Click Advanced (Figure 23).

Figure 23:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 33
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

5. Select the WINS tab, add the WINS addresses, then

set the LMHOST and NETBIOS settings. See
Figure 24 on page 34 recorded in Step 6 on page 20
6. Click OK three times when required.

Figure 24:

NOTE Do not close the Network Connection window.

If the Link Speed and Duplex value you recorded in Step 13 on page 22 was Auto, close all windows and skip to
Step 9 on page 36.
7. Right-click Hospital LAN and select Properties.
8. Set the Link Speed and Duplex settings (Dell 650) or Media Type (Dell 530) recorded during Step 13 on page 22:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 34
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

a. Click Configure as shown in Figure 25 on page 35.

Figure 25:
b. Click the Advanced tab, and from the Property menu choose:
• for Dell 650: Link Speed & Duplex as shown in Figure 26 on page 36
• for Dell 530: Media Type as shown in Figure 27 on page 36
c. Select the value you recorded in Step 13 on page 22 when the Link Speed and Duplex setting was saved.
d. Click OK and close the Network Connections window.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 35
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Figure 27: Dell 530: Media Type

Figure 26: Dell 650: Link Speed & Duplex

9. If needed restore the Proxy Settings recorded during the backup in Step 6 on page 24.
a. Click Start > Settings > Control Panel > Internet Options.
b. Click the Connections tab.
c. Click LAN Settings as shown in Figure 13 on page 23 and type or set the Proxy settings you recorded in Step
on page 23:
d. Click OK twice and close all windows.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 36
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Verifying and Changing EOD drive letter

Make sure that the EOD drive letter is F. If drive F is already allocated to another device, switch drive letters using Disk
Management.
1. On the desktop right-click on My Computer and in the menu click Manage.
2. Select Disk Management in the Computer Management tree. A Computer Management window, similar to the one
in Figure 28 on page 37 appears.

Figure 28: Example of the Computer Management Window

3. Verify the EOD (removable) drive is labeled F:\. If the drive letter is incorrect, change the drive letter as follows,
otherwise close the Computer Management window and continue with Installing the Host Application Software on
page 39:
Change the first incorrectly-labelled drive letter (drive F:) to an unassigned letter according to the following
procedure. Highlight the disk to change.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 37
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

NOTE The system does not allow two drives with the same letter. This means that if you want to exchange the drive
letters of two or more drives, you need to give one of the drives an alternate letter temporarily.

a. Right-click and select Assign Drive Letter

in a window similar to the one shown in
Figure 29 on page 38.
b. The Assign Drive Letter window shown in
Figure 30 on page 38 opens. From the pull-
down menu assign the disk an unassigned
drive letter. In the end you want the following
assignments:
• Drive A:
• Drive C: Local disk (C:)
• Drive D: Local disk (D:)
• Drive E: CD/DVD
• Drive F: Removable (EOD
• Drive G: CD-R (if it exists)
c. Click OK to close the Assign Drive Letter
window.
Figure 29: Disk Administrator Window (Example Only)
d. A confirmation window opens. Click Yes to
confirm the change and close the window.
e. Repeat steps a on page 38 to d on page 38
and change the EOD drive letter to the
correct disk letter (F).
f. Click OK to close the Assign Drive Letter
window.
g. Repeat steps a on page 38 to d on page 38
to assign the correct letter to the first drive.
4. Close the Computer Management window.

Figure 30:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 38
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Installing the Host Application Software

Installing the Supplemental CD

The Supplemental CD installation procedure takes approximately 1 minute.
NOTE Choose the appropriate CD for your system configuration.
1. Insert the Supplemental CD according to your system (see Table 11 on page 39).
Table 11: Brilliance CT Supplemental CD

Part Number Description

4550 128 99401 BR 16-slice Supplem. CD V2.2.1.14009

4550 128 99411 BR 10-slice Supplem. CD V2.2.1.14009

4550 128 99481 BR 6-slice Supplemental V2.2.1.14009

4550 128 99461 Supplemental 16-Slice V4.2.1.14009

4550 128 99471 Supplemental 10-Slice V4.2.1.14009

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 39
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

2. Wait for the Brilliance

Supplemental Wizard to appear.
3. Select Typical Supplemental
Installation and click Next as
shown in Figure 31.
4. Do not touch the mouse or the
keyboard; wait for message
“Installation wizard completed”
appears.
5. Click Finish and eject the
Supplemental CD.

Figure 31:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 40
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Installing COTS/Security Components

NOTE Security Components and COTS installation procedure takes approximately 15 minutes.
1. Insert the IDT/BR [Link] CD V2.2.0.4 CD into the CD-ROM drive (see Table 12 ). The Philips Installation
dialog box automatically opens.
In sert the CD labeled Bri lliance_ 40_Envi roment_C reator. The Ph ilips Installation d ialog box opens au tomatically.

Table 12: Mx8000 IDT/Brilliance CT Security/COTS V2.2.0.4

Part Number Description

4550 128 99421 IDT/BR [Link] CD V2.2.0.4

2. Wait for the Security_COTS V2.2

Wizard (Figure 32) to appear.
3. Select Typical and click Next.
NOTE The computer will restart a
few times during the
installation process. Do not
touch the mouse or the
keyboard. Wait for the
message “Installation wizard
completed” .
4. When the message Installation
wizard completed appears, click
Finish.

Figure 32:

!
CAUTION The UPS software load is no longer needed. Do not try the above CD to load the UPS software.
5. Eject the CD.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 41
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Installing the IRS Addon on Host PC (only for systems with IRS)
NOTE The IRS Addon installation procedure takes approximately less then a minute.
NOTE If you only have a CIRS or a vertical server skip this section and continue with Installing Host Software on page
43.
1. Insert the appropriate IRS Add-on CD into the Host CD drive.
Table 13: Mx8000 IDT/Brilliance CT IRS AddOn V4.2.0.1/[Link]

Part Number Description

1 4550 128 99491 16-Slice IRS Add-on V4.2.0.1/[Link]

2 4550 128 99501 10-Slice IRS Add-on V4.2.0.1/[Link]

3 4550 128 99511 6-Slice IRS Add-on V4.2.0.1/[Link]

2. The Installation window appears.

Click Next.
NOTE This process will take only a
few seconds.
Do not touch the mouse or
the keyboard; wait for
message “Installation wizard
completed” appears
3. When the message Installation
wizard completed appears, click
Finish.
4. Eject the CD.

Figure 33:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 42
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Installing Host Software

Host Software installation procedure takes approximately 15 minutes.
1. Insert the IDT/BRHost V4.2.1.1925/2.2.1.1925 CD. The Philips Installation Wizard opens automatically as shown in
Figure 34 on page 43.

Part Number Description

4550 128 99431 IDT/BRHost V4.2.1.1925/2.2.1.1925

2. Select Typical and click Next. The

installation takes approximately 15 minutes.
NOTE During the installation process the
computer automatically restarts and
logs on. Do not touch the keyboard
or mouse.
l

3. Click Finish.
4. Eject the CD.

Figure 34: Install Host Window

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 43
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Installing the Supplemental (Version) CD

1. Insert the appropriate Supplemental CD for your system configuration and wait for the Brilliance CT Supplemental
Installation wizard to open (see Figure 31 on page 40).

Part Number Description

4550 128 99401 BR 16-slice Supplem. CD V2.2.1.14009 CD

4550 128 99411 BR 10-slice Supplem. CD V2.2.1.14009 CD

4550 128 99481 BR 6-slice Supplemental V2.2.1.14009 CD

4550 128 99461 Supplemental 16-Slice V4.2.1.14009 CD

4550 128 99471 Supplemental 10-Slice V4.2.1.14009 CD

4550 127 01921 IDT/BR 6 Supplem.CDV2.2.1.14024

2. Ensure Typical is selected.

3. Click Next.
The Installation Validation dialog box
shown in Figure 36 on page 45
appears.
4. Click the Abort Timer button.

Figure 35:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 44
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

NOTE The dialog box closes automatically after 30 seconds. If the window closed too quickly, double-click the Installed
Version icon on the desktop and continue with the following Step 5 on page 45.

5. Verify that the Missing

Components and Extra
Components boxes are
empty. Click OK.

Figure 36:

NOTE If there are any missing components you must repeat the procedure starting from section Host OS Installation
on page 30. If IRS / CIRS are the missing components, check for missing components again after the IRS / CIRS
upgrade is done by clicking the Installed Versions icon on the desktop.
6. Click Finish to close the installation and eject the Supplemental CD.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 45
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Installing HOTFIX KB928388

Install the Hotfix KB928388 by completing the following procedure:
1. Insert the CD labelled Philips_MS_HotFix KB928388_2.2.0.0003 into the CD drive.
2. In case the Brilliance CT Security Update wizard shown in Figure 37 on page 46 does not open automatically,
double-click My Computer on your desktop and then double-click the CD drive.

3. Click Next. The installation

process begins.
4. Click Finish once the
process is complete.
5. Eject the CD.
6. Restart the Host.
7. Log on as philips_service.

Figure 37: Brilliance CT Security Update wizard

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 46
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Installing BR IDT Supplemental

Install the Host Add-On BR IDT by completing the following procedure:
1. Insert the CD labelled BRIDT Suppl.V2.2.1/4.2.1.14016 into the CD drive.

Part Number Description

4550 128 99541 BRIDT Suppl.V2.2.1/4.2.1.14016

NOTE In case the Philips MS IDT Upgrade wizard shown in Figure 38 on page 47 does not open automatically, double-
click My Computer on your desktop and then double-click the CD drive.

Figure 38: Philips MS IDT Upgrade

2. Select Host.
3. Click Next. The installation process begins.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 47
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

4. Click Finish once the process is complete. A cmd window opens and the Installation Validation report appears.

Figure 39:
5. If you clicked Abort Timer click OK.
6. Eject the CD and restart the Host.
7. Log on as philips_service.
4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 48
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Installing the CDR/MPR Fix 2.2.1/4.2.1 14021 CD

Table 14:

Item # Part Number Name S/W CD for Host

1 4550 127 01771 CDR/MPR Fix 2.2.1/4.2.1 14021 CD

1. Insert the CDR/MPR Fix 2.2.1/4.2.1 14021 CD

into the CD/DVD-ROM drive.
The Installation window (Figure 40) appears.
NOTE If the CD does not automatically start,
go to My Computer and double-click the
CDR/MPR Fix 2.2.1/4.2.1 14021 CD
2. Click Next.
3. Wait while the files are being installed.
4. When the installation is complete, click Finish.
The Installation window closes

Figure 40:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 49
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

5. The installation validation

window (Figure 41) appears.
Verify the Installed Version
according to Table 15 on
page 50.

Figure 41: Installation Validation Window

Table 15: Modality Updated

Model Version

Mx8000 IDT (CIRS/IRS) 4.2.1.14021

Brilliance CT (CIRS/IRS) 2.2.1.14021

6. Eject the CD and restart the Host.

7. Log on as philips_service.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 50
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Installing the Supplemental CD (for Brilliance 6-Slice with CIRS Only)

NOTE For all other systems, skip this procedure.
Table 16: Supplemental CDs

Item # Part Number Name S/W CD for Host

1 4550 127 01921 IDT/BR 6 Supplem.CDV2.2.1.14024 CD

1. Insert the IDT/BR 6 Supplem.CDV2.2.1.14024

CD into the CD/DVD-ROM drive.
The Installation window (Figure 42) appears.
NOTE If the CD does not automatically start,
go to My Computer and double-click the
IDT/BR 6 Supplem.CDV2.2.1.14024 CD
2. Click Next.
3. Wait while the files are being installed.
4. When the installation is complete, click Finish.
The Installation window closes

Figure 42:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 51
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

5. The installation validation

window (Figure 43) appears.

Figure 43: Installation Validation Window

6. Eject the CD and restart the Host.
7. Log on as philips_service.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 52
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Restoring Computer Name and Domain/Workgroup Settings

Restore the computer name and Domain/Workgroup Settings as follows:
1. On the desktop right-click My Computer and select Properties.
2. Select the Computer Name tab. Click Change.
3. Enter the Computer name that was recorded in Table 10 in section Recording Network Settings on page 17.
4. In the Member of area, choose Domain or Workgroup. Type in the Domain or Workgroup name and click OK.
5. If your system is within a domain enter user and password supplied by the hospital administrator and click OK. Wait
until you are admitted into the local domain.
NOTE The IT administrator may need to add your computer back to the Domain.
6. A message appears: “You must restart the computer for the changes to take effect”. Click OK.
7. Click OK on the System Property window.
8. A message “Changes will not take effect until after restart” appears. Click Yes to restart the computer.
9. Log on as philips_service.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 53
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Setting the K2D Visa

NOTE This key is required for the activation of the Service, Calibration, and Diagnostic tools.
Local Proprietary diagnostics reside on the Brilliance system and are currently enabled by the use of the Philips K2D
Visa Software key, which can be obtained by contacting your local SSR service key administrator. Contact the
appropriate SSR representative for details:
• CT RTAC - North America
• Maarten Leertouwer/EHV/MS/PHILIPS
• Ravindra Sukthankar - ASPAC
• Bernardino Alonso - LATAM

The following information is needed to request a key:

• Requestor’s Philips e-mail address
• System Type
• SW version
• System Serial Number
• Machine ID (Can be obtained by a system console command, described in the Service manuals)

In addition, in case of demand service on a non-contract site or when a system is down and the K2D Visa has expired,
a web page has been developed to allow the FSE access to immediately obtain a 5 day key. The URL for this web page
is [Link]

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 54
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

The following information is needed to request a key:

• Requestor’s Philips e-mail address
• System Type
• SW version
• System Serial Number
• Machine ID (Can be obtained from the K2000 Visa entry (Figure 44).
The base level of AIAT (Assemble, Install, Adjust, Test) software required to meet FDA 21CFR Regulations (O-Level) is
resident on the system and does not require the use of a K2D Software key for access. O-Level service documentation
and phantoms are available for purchase by any interested party outside of PMS. Interested parties should be directed
to contact PMS local representative.
NOTE Either the K2 Visa or the K2000B Visa key can be used when obtaining the key from the web site.

1. If needed, log on as philips_service.

2. Double-click the VisaEntry icon located on the Desktop.
3. The K2000 Visa Entry dialog box appears. Record the machine ID
(needed to get the visa key).
4. Obtain a visa (the K2000 key).
5. Enter the visa in the K2000 Visa Entry dialog box and click Apply.
6. Click Done.
7. Log off.
8. Log on as philips_service.
9. To verify that the Visa is enabled, double-click the VisaEntry icon
located on the Desktop and view the Status: Visa Valid.
10. Click Done. Figure 44: Visa Entry Window

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 55
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Verifying and Set the Time and Date

Double-click the clock in the System Tray (bottom right-hand corner of the Desktop); the Date / Time Properties
dialog opens. Verify that the following are correct to your country settings:
1. Time Zone
a. Select the Time Zone tab.
b. Select your time zone from the list. Make sure the check box Automatically adjust clock for daylight saving
changes appears under the map is checked as shown in Figure 45 on page 56:

Figure 45:
c. Click Apply.
2. Date and Time
a. Select the Date & Time tab.
b. Verify the date and time are set correctly.
3. Internet time
a. Select the Internet Time tab
b. Verify that Automatically Synchronize with an Internet Time Server Marker is not checked.
4. Click OK to close the dialog box.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 56
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Post Host Installation

Configuring the Host Dual Monitor Settings

NOTE If you do not have a Dual Monitor skip this section and continue with Configuring the Host Monitor Refresh Rate
With a Single Monitor Installation on page 59.
NOTE Make sure that both monitors are connected.
1. From the Desktop, right-click and select Properties.
2. Set Dual Monitor configuration as follows:
a. Select the Settings tab and then click
Advanced as shown in Figure 46.
b. Click the Quadro4 980 XGL (see Figure 47 on
page 58), FX-1400 (see Figure 48 on page 58)
or 700 XGL (see Figure 49 on page 58) tab
(depending on your computer model). A menu
appears on the left.
c. Select nView Display Settings from the menu
on the left.
NOTE If you do not see nView Display Settings in
you menu turn off the host make sure that
both monitor are connected, turn on the
host log in as Philips service and redo the
above step 1.
d. If the left (1) monitor is not highlighted as
primary, click it and then select the “Make this
the primary display” check box.

Figure 46:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 57
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

e. Click Apply. Do not click OK.

Figure 47: nView Display Settings - Quadro4 980 XGL Figure 48: nView Display Settings - FX-1400
f. Verify that Horizontal span is selected in the nView Display
Mode drop-down list.
NOTE If all buttons are grayed out:
1. Select monitor 2, and clear the 'Extend my windows
desktop onto this monitor' check box and click Apply.
2. Select monitor 1, then select the Horizontal span.
g. Click Apply. Do not click OK.
h. Click Yes to confirm the settings. Once the right-hand screen
is activated Do not click OK.
3. If the monitors appear swapped, perform the following steps. If
the monitors are not swapped, skip to the following Step 4 on
page 58.
a. Set Primary Display and Secondary Display appropriately. Figure 49: nView Display Settings - Quadro4
b. Verify Make this the primary display is checked. 700 XGL

c. Click Yes to confirm the settings.

4. Click OK (one time only).

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 58
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Configuring the Host Monitor Refresh Rate

With Dual Monitors

1. Verify that the Screen Resolution is set to 2560x1024. If you had to change it, make sure you click Apply.
2. Click the Advanced button as shown in Figure 46 on page 57.
3. Select the Monitor tab. Verify the Screen Refresh Rate is set to:75Hz for an LCD monitor.

4. Fix Monitor Flicker as follows:

a. Select the Troubleshoot tab.
b. In the Hardware acceleration area move the
Hardware acceleration slider to the third line from
left as shown in Figure 50.
c. Click OK twice to close the Display Properties
dialog box.
If changes were made, click Yes in the confirmation
message box.
d. Close the Control Panel window.
e. Skip to Exceed Configuration on page 60.

Figure 50:

With a Single Monitor Installation

1. From the Desktop, right-click and select Properties.
2. Select the Settings tab and click the Advanced button (Figure 46 on page 57).
3. Select the Troubleshooting tab.
4. In the Hardware acceleration area move the Hardware acceleration slider to the third line from left (Figure 50 on
page 59).
5. Click OK twice to close the Display Properties dialog
6. Close the Control Panel window.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 59
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Exceed Configuration
Update the Exceed configuration as follows:

1. Click Start on the Task bar.

2. Select Programs > Hummingbird Connectivity
V7.1 > Exceed > Xconfig.
3. Enter the password admin in the window shown in
Figure 51, and then click OK.
4. Double-click the Transports icon shown in Figure 53
on page 60. Figure 51: Password Dialog box

5. Press the button "Choose..." as shown in Figure 52

on page 60

Figure 52:
6. From the drop-down list select Network Only
Interface and click OK and then click OK in all
windows.
7. Click File > Exit.

Figure 53:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 60
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Acrobat Reader and CesarFTP Initialization

Initialize Adobe Reader as follows:
1. On the Desktop, double-click the Adobe Reader icon.
2. In the software license agreement window, click Accept.
3. Close Adobe Reader.

Initialize CesarFTP as follows:

1. On the Desktop, double-click the CesarFTP icon.
2. Click Control and select Exit.
3. Click OK.

Configuring Administrative Tools Security Features

1. Click Start > Settings > Control Panel.
2. Click Administrative Tools.
3. In the Administrative Tools window, double-click on Local Security Policy.
4. From the left side menu tree, open Local Policies > Audit Policy.
5. Double click on Audit logon events and check the Success and Failure options. Click OK and close the Local
Security Policy dialog.
6. Go back to the Administrative Tools window and double-click Event Viewer. Right-click on Security (in either right
or left panes) and click Properties.
7. In the Log Size area, change the Maximum log size to 2048.
8. Click OK and close the Event Viewer window.
9. Close the Administrative Tools window.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 61
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

SnagIt Configuration
NOTE The SnagIt configuration is set automatically. If needed verify the SnagIt Configuration as follows:
1. On the Desktop click Start > Programs > SnagIt 8 > SnagIt 8.
The SnagIt window appears.
2. Click the Image Capture profile from the Profiles area (Figure 54 on page 62).
3. In the Profile Settings area, click the Input button and select Active Window.
4. Click the Output button, and select Catalog. Click the Output button again, and select Properties.
The Output Properties window appears, with the Catalog Browser tab displayed, (Figure 55 on page 63).

Profile selection
area

Profiles settings
area
Figure 54: Snagit window

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 62
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

5. If required, set the Catalog folder to d:\SMI\Snagit (see Figure 55).

6. In the Catalog Browser Options area, verify that both checkboxes are clear (see Figure 55).
7. Click Apply, and then click OK to close the Output Properties window.

Figure 55:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 63
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

8. In the Catalog Browser tab, change the

destination folder to D:\SMI\Snagit
Figure 56.
9. Verify that both Start and Show browser
when capture is added to catalog option
are not checked.
10. Click Apply.
11. Click OK.
12. Click Save Profile.
13. Click Overwrite.
14. Close Snagit.

Figure 56:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 64
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Restoring System Files

Perform restore of the calibration and configuration files from an EOD disk as follows:
Restore system parameters from the Backup EOD disk as follows:
1. Insert the EOD containing the backup data into the EOD drive.
2. Insert the Supplemental CD. Refer to Table 17 on page 65 for the correct CD for your system.
Table 17: Brilliance CT Supplemental CD

Part Number Description

4550 128 99401 BR 16-slice Supplem. CD V2.2.1.14009 CD

4550 128 99411 BR 10-slice Supplem. CD V2.2.1.14009 CD

4550 128 99481 BR 6-slice Supplemental V2.2.1.14009 CD

4550 128 99461 Supplemental 16-Slice V4.2.1.14009 CD

4550 128 99471 Supplemental 10-Slice V4.2.1.14009 CD

3. The Philips Install Wizard appears. If the Philips Install Wizard does not appear on the desktop double-click My
Computer and double-click the CD icon.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 65
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

4. Select Post Install and click Next

as shown in Figure 57 on
page 66; a browse window opens.
5. Navigate and select the Backup
directory according to date: on
drive F:\—the EOD drive that was
saved starting from Step 2 on
page 12.
6. Click OK.

Figure 57: Supplemental Window

7. A CMD window opens. If the previous version cp: F:/IDT_BACKUP/sys/d%temp/[Link]: The system cannot find the
is not recognized a selection appears to path specified. Find which version you are upgrading from
choose from (Figure 58).
awk: input file “d:/temp/[Link]: The system cannot find the file
• If you upgrade from V3.25/1.25 type "1" specified. Can’t find which version you are upgrading from .
• If you upgrade from V4.02/V2.0.2 Type "2" Which version are you upgraidng from?
8. Press Enter. 1 1.x.x
9. Select again the Backup directory according to 2 2.0.x
date 3 2.2.0
(drive F:\—the EOD drive), and click OK.
4 None
10. Click Start Restore. #?
11. When Restore is complete click OK, then Figure 58:
Close and Exit.
12. Wait until the CMD window closes and the Finish button is enabled. Click Finish.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 66
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

13. Eject the Supplemental CD.

14. Close all open windows.
15. Restart the computer and Log on as philips_service.

License Key Installation

!
CAUTION Before downloading the updated license key, make sure that the license key includes 4x4.5
collimation.

Overview
Download the license key from the Philips Medical website as instructed in Obtaining the License Key from the Philips
Medical Website on page 67 and then install the license key as instructed in Installing LIcense Key on page 69.

Obtaining the License Key from the Philips Medical Website

Obtain the license from the Philips Medical Systems website at:
[Link]
1. In the Search Options window (Figure 59), enter the
System Serial Number.
2. Click Search.
3. Select the required system type and click on CLICK
HERE FOR THE FULL PAGE to view all details.
4. Make sure that the updated license key includes 4x4.5
collimation. If not, call the CT/Line of Business Help
Desk. Figure 59: Search Options Window

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 67
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

5. At the bottom of the page, click on the Key Code Auto

Installation Tool link. The File Download window
(Figure 60) appears.
6. Click Save and save the file to the directory of your
choice (saving to the Desktop is convenient).
7. Burn the file to a blank CD and install the license key
as described in the next section.

Figure 60: File Download Window

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 68
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Installing LIcense Key

1. Double-click the Update Key icon on the Host Desktop; the License Key and Protocols Wizard opens.
2. Click Next.
NOTE If you are installing the license key from a batch file, the path to the location of the batch file must be without any
spaces in the file and path name.

3. In the next window (Figure 61), choose one

from the following options:
• Install License Key from the batch file:
use this option if you have the license key
batch file.
• Install License Key manually:
use this option if you have printed copy of
the license key
4. Click Next.

Figure 61:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 69
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Install License Key from the batch file

1. The Windows Explorer opens. Navigate
to the location of the Option License Key
batch (XXXXX*.BAT) file and double-click
on it; the Windows Explorer closes and a
command window opens.
2. In the command window click any key to
continue and then click Install in the
License Key and Protocols window
(Figure 62).
3. A popup appears; Continue to Protocol
Conversion: Yes or No.
• Click No.
4. Click Finish and continue with Protocol
Conversion on page 71.
Figure 62:

Install License Key manually

NOTE The values in Figure 63 on page 70
are for illustration only.
1. The Type License Key window (Figure 63)
opens. Type in the Option License Key as
it appears in the printed copy of the license
key.
2. Click Next and then click Install.
A progress bar appears showing the
license key installation.
3. A popup appears; Continue to Protocol
Conversion: Yes or No.
• Click No.
4. Click Finish and continue with Protocol Figure 63:
Conversion on page 71.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 70
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Protocol Conversion
1. On the Desktop double-click the Scanner Application icon
2. Click Home > Misc > Protocol Converter. The Protocol Conversion Utility window (Figure 64) opens.
3. In the Source directory box type c:/usr/[Link]/spr.
4. Verify the Destination directory type is c:/usr/[Link]/spr. Otherwise type c:/usr/[Link]/spr.

Figure 64:
5. Click Convert to start the conversion process.
NOTE It is normal for the Source box to change to c:/usr/tmp/spr_convert_temp.
6. Wait until the message Conversion Finished appears.
7. Verify the Error box is empty; indicating that all protocols were converted correctly.
8. Click OK. Click OK again in the Protocol Conversion Utility window.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 71
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

!
WARNING During the protocol conversion process, invalid converted protocol errors are saved
in a Protocol Conversion log file.
• Navigate to the Protocol Conversion log:
D:/SMI/SnagIt/conver_results_200x_xx_xx.txt
(where xx is the date the log was created) and review the problems encountered
during conversion.
• It is the responsibility of the FSE to show all the invalid protocols to the chief
technician at the site and be corrected by the application specialist or site
technician.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 72
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Correcting Corrupted Protocols After Protocol Conversion

During the protocol conversion process, invalid converted protocol errors are saved in a Protocol Conversion log file.

Protocol Conversion log path

Protocol not converted

• If an invalid protocol was created during the conversion, the

exam protocol button is red instead of yellow in the Exam
Protocols window shown in Figure 65 on page 73.
• To view the error that caused the Protocol Conversion failure
navigate to the Protocol Conversion log:
D:/SMI/SnagIt/conver_results_200x_xx_xx.txt (where xx
is the date the log was created) and review the problems
encountered during conversion as shown in Figure 66 on
page 74.
• The log will show the unaccepted parameters and the
recommended change. Figure 65:
• The application specialist or site technologist can correct the
protocol in Generate Protocol.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 73
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

!
WARNING Protocol will fail the conversion if the customer does not have the associated option
installed; for example cardiac.
It is the responsibility of the FSE to show all the invalid protocols to the chief
technician at the site and correct them together with the application specialist or
site technician.

Figure 66: Log showing Failed Protocol Conversion

Protocol Correction Example

1. Click Generate Protocol.
2. Select the Head group.
3. Click on the protocol with the red icon as shown in Figure 65 on page 73.
4. Click on each protocol in the Protocol set until the message appears “Invalid step [Link]” and click Cancel.
5. Correct the Thickness and the collimation.
6. Click OK.
7. Select Age group and click Save.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 74
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Restore Varian RPM™ Settings

NOTE If the Varian RPM™ option is not installed, skip this procedure and continue with Windows Network Paper
Printer Installation on page 76.
NOTE Make sure the Varian RPM is turned on and connected to the network. If it is not, you will not see the mounted
drive:
1. Connect the Varian RPM to the network and turn it on.
2. Restart the CT Host computer.
3. Log on as philips_service.

1. Press the keys Windows+D.

2. Double-click on Map Drive icon on the desktop. The
Create Mapping window shown in Figure 67 on
page 75 appears.
NOTE Use information recorded previously in Step 2
on page 26 if applicable.
3. In the IP Address text box, type the path to the Varian
RPM™ folder using the following format:
\\<Varian RPM™ IP address>\<share folder name
and path> ie gating\breath
4. If needed in the User Name text box, type the Varian
RPM™ user name.
5. If a password is required, type the Varian RPM™
password in the Password text box. Figure 67: Create Mapping

NOTE The user name and optional password must be valid for accessing the Varian RPM™ shared drive. If the shared
drive is password-protected, the password for the user name must be provided. A domain name may be required
as a modifier for the user name and should be entered as part of the user name, i.e. "<domain name>\<user
name>".
6. Click OK. A success message appears.
NOTE If you get a script error message, reconfirm the parameters that were entered and click OK again
7. Click Close.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 75
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Windows Network Paper Printer Installation

Use the following instructions to install network paper printers.
If a network paper printer was previously connected, perform the following procedure to reinstall the network paper
printers.
NOTE If you are not installing a paper printer skip to Restore Custom Hospital Logo on page 79.
1. Click Start > Settings > Printers and Faxes.
2. In the menu bar click File > Add Printer.
3. The Add Printer Wizard appears. Click Next.

4. Select the option Local printer attached to this

computer and clear the selection Automatically
detect and install my Plug and Play printer. Click
Next.
5. The Select a Printer Port dialog box appears. Select
Create a new port and in the Type of port list select
Standard TCP/IP. Click Next twice.

Figure 68:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 76
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

6. The Add Port dialog box appears. Type in the Printer

name or the IP address you wrote down in Step 6 on
page 29.
7. Click Next.
8. Click Finish. The Install Printer Software dialog
appears.
9. Wait until the Manufacture list appears. Select the
Manufacturer and Printer from the lists according to
the printer information you wrote down in Step 3 on
page 27.
10. Click Next. The Name Your Printer dialog box
appears.
11. Type the name according to the information you wrote
down in Step 6 on page 29.
12. Click Next. The Printer Sharing dialog box appears.
13. Select Do not share this printer and click Next.
14. The Printer Test Page dialog box appears. Check that
a paper was printer.
15. Select Yes if you wish to test the printer and click
Next. Figure 69:

16. Click Finish. The printer is installed and will appear in the Printers and Faxes window.
17. Click Finish to close the wizard.
18. Repeat this procedure for all the network paper printers.
19. Check the port configuration settings for all the network paper printers:
a. Click Start > Settings > Printers and Faxes.
b. The Printers and Faxes window appears. Right-click the windows paper printer in the Printer name list and select
Properties.
c. Click the Ports tab. Highlight the IP port and click Configure Port.
d. Verify that the setting are the same as recorded in Step 6 on page 29.
20. Click Cancel twice and close the Printer and Fax window.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 77
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Set the Default Network Paper Printer

1. On the desktop double-click Olevel Interface.
2. Click
3. The Printer Configuration dialog box appears.
4. Select the paper printer to use as the default printer.
5. Click Set Default Printer.
6. Click Close.
7. Click Exit to close the Olevel Application.

Figure 70:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 78
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Restore Custom Hospital Logo

NOTE If you are not required to restore the customer logo skip to Verify the Gantry Position on page 81.

1. If the scanner application is not open, double-click

Scanner Application icon on the desktop.
2. Click Preferences > Other > Launch Application >
Launch Report.
NOTE If you have a single monitor click the Processing
tab.

3. The System Configuration dialog box appears.

Figure 71:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 79
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

4. Click Logo.
5. The Report Logo Configuration dialog box appears.
6. Click Import. The Explorer dialog box appears.
7. Navigate to the custom logo saved in
Step 4 on page 26.
8. Select the logo and click Open.
9. Click Apply in the Report Logo Configuration dialog
box.
10. In the Report Logo Configuration dialog box, click on
the logo to select it (put a check mark in the default
column for the custom logo) and then click Assign.

11. In the Assign Logo to Report dialog box select Apply

to all existing reports and then click OK.
12. in the Report Logo Configuration dialog box click
Close.
13. Click Exit in the System Configuration dialog box.
14. Click OK on the message to save the changes.

Figure 72:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 80
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Verify the Gantry Position

1. If needed on the desktop double-click the Scanner Application icon.
2. Open the Preferences:
• For a dual monitor on the right monitor click Preferences

• For a single monitor click first the Processing tab and then click Preferences.

3. In the Scanner Options click Set Scanner Position.

4. Verify or update the Gantry position according to the setting recorded in Step on page 24.
5. If the position was changed, click Yes and then click OK.

Restoring Default Storage Device

1. In the Preferences > Scanner Options click

Default Storage Devices and then click Default
Storage Devices button.
2. Verify or update the devices listed according to the
settings recorded in Step 2 on page 25.
3. Click OK in the Generate Default Target Devices
dialog box.

Figure 73:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 81
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Changing HIS/RIS Restrictions

NOTE If a direct HIS/RIS connection is not needed click OK to close the Preferences and skip to Checking the IBox
Software Version on page 83.
Use this procedure to allow access to a URL when the system uses a direct HIS/RIS connection.

1. Select Scanner Options > HIS/

RIS.
2. If the system has a direct HIS/RIS
connection, access to a URL must
be configured.
3. Select the Direct HIS/RIS address
that appears in the text box and
press Ctrl+C.
4. Click OK to close the Preferences
window.
5. Press Windows+D to access the
Desktop.
6. Double-click the URL Restriction
icon. Figure 74:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 82
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 V2.2.1/4.2.1 Host Software Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

7. In the Allow this website field, press Ctrl+V to paste the URL
you copied from the Preferences dialog.
8. Click ADD.
9. Click Apply.
10. Click OK.

Figure 75:

Checking the IBox Software Version

Perform the procedure IBox Software Upgrade on page 161. If there is no IBox installed on the system, skip to Remote
Recon Option Upgrade on page 83.

Remote Recon Option Upgrade

If your Brilliance CT (water)/MX8000 IDT system with a CIRS has the Remote Recon option installed upgrade the
Extended Brilliance Workspace to the new version EBW V2.0.62 compatible with the software version installed on the
scanner use the software CD kit and installation instructions delivered with the Brilliance CT (water) V2.2.1/MX8000 IDT
V4.2.1 Upgrade Kit. Otherwise skip to Foreign Language Installation Instructions on page 84.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 83
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Foreign Language Installation Instructions
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Foreign Language Installation Instructions

NOTE Perform this procedure only after installing the localized language keyboard (not English). See Figure 76 on
page 84 for the supported languages.
NOTE If you are using an English keyboard skip this section:
• If you have and IRS, skip to Installing the IRS Operating System on page 87.
• If you have a CIRS, skip to Full CIRS Software Installation on a Two Server Configuration on page 101 or CIRS
Software Installation on a Single Server (Vertical Server) Configuration on page 118
Install the foreign language as follows:

1. Log on as philips_service.
2. Navigate to c:\misc\lang and double-click install_languages.exe. The
Install Language window opens (see Figure 76)
3. Select the desired default language for the system.
4. Click Install Language.
The keyboard language automatically switches to the newly Installed
language.

Figure 76: Install Language Dialog

box

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 84
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Foreign Language Installation Instructions
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

5. The xconfig dialog box appears (see Figure 77). Use the equivalent keys
on the localized keyboard to type the password admin and click OK.
6. The [Link] window Figure 78 on page 85 appears. Double-click
Keyboard input.
7. The Keyboard Input dialog box shown in Figure 79 on page 85 appears.
From the Primary drop-down list select the default keyboard language.

Figure 77: Password Dialog Box

NOTE The language file name is the language name with the file extension “kbf ”. For example, the English language file
is [Link]).

Figure 78: [Link] Window

Figure 79:
8. Click OK.
9. Close the [Link] window.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 85
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Foreign Language Installation Instructions
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

10. Wait until the message **name of language** is

chosen” appears at the bottom of the Install Language
window (Figure 80).
11. Click Close.

Figure 80:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 86
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Installing the IRS Operating System
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Installing the IRS Operating System

NOTE Perform this procedure if your system has an IRS. If you have a CIRS skip to Full CIRS Software Installation on a
Two Server Configuration on page 101 or CIRS Software Installation on a Single Server (Vertical Server)
Configuration on page 118.
NOTE To switch the KVM to the IRS connection press the Ctrl key twice.

Deleting RAW Data from the IRS

NOTE 800 MB of free space on drive E:\ is required for the IRS software installation.

!
CAUTION Inform the CT operator before deleting any RAWs from the IRS.
1. Switch to the IRS computer using the KVM switch (press the Ctrl key twice).
2. From the Windows Start menu, select Programs > Administrative Tools > Disk Administrator.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 87
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Installing the IRS Operating System
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

3. Right-click Disk E: in the Disk Administrator

window. Select Format from the shortcut
menu (Figure 81).

Figure 81:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 88
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Installing the IRS Operating System
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

4. The Format E:\ window (Figure 83) appears.

5. Select NTFS from the File System list.
Make sure that the Quick Format check box is not
selected.
6. Click Start.
7. Click OK in the Warning window (Figure 82).

Figure 82:

Figure 83:

8. When the Formatting Complete message (Figure 84)

appears, click OK.
9. Click Close in the Format E:\ window (Figure 83 on
page 89).

Figure 84:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 89
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Installing the IRS Operating System
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

10. The NTFS-formatted partition is now displayed in the Disk Administrator window (Figure 85).

Values for disks 0 and 1 (C, D and E)

are different for each system

Note:
Disk 1 Free space for 4-Disk
configuration is 280000 MB

Figure 85:
NOTE The actual screen may look different from Figure 85, depending on RAID configuration:
• 6 disks of 73 GB each
• 4 disks of 73 GB each
• 6 disks of 18 GB each

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 90
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Installing the IRS Operating System
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Modifying Drive Letters

1. From the Windows Start menu, select Programs >

Administrative Tools > Disk Administrator.
2. At the message prompt click OK.
Values for Disk 0 (C & D) are
3. When a window opens, click Yes to open the Disk different for each system
Administrator window (Figure 91).
4. Make sure that drive E is assigned correctly:
• Drive E: Local (RAID) Disk:
• total size 280 GB for 4 (73 GB) SCSI Disk
configuration
or
A
• total size 420 GB for 6 (73 GB) SCSI Disk
configuration.
or
• total size 105 GB for 6 (18 GB) SCSI Disk
configuration.
Figure 86: Disk Administrator Window

NOTE In all configurations, the size of Drive E: should be 105 GB. If not, refer to the newsletter CT3536-67 New IRS 73
GB SCSI Array Configuration Procedure that is located on the InCenter at Service > Products & Solutions >
Computed Tomography > Brilliance Series > Brilliance CT 16/10/6 (water) > General > Newsletters.
If two drive letters must be switched, change the first incorrectly-labeled drive letter to a letter that is unassigned.
Highlight the disk to change.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 91
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Installing the IRS Operating System
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

a. Right-click the disk to change and select Assign Drive Letter... (A)
to open the Assign Drive Letter window (Figure 92).
b. From the drop-down menu (B), assign an unassigned drive letter to
the disk.
c. Click OK (C) to close the Assign Drive Letter window.
d. When a confirmation window opens, click Yes. B

e. Repeat Step a to Step c and change the second drive letter to the
correct disk letter.
f. Repeat steps Step a to Step c to assign the correct letter to the first
drive. C

Figure 87:

5. Make sure that the drives are assigned correctly (Figure 88). Drive C: Local Disk, total size 4.1 GB
If not, use the ‘+’ and ‘-‘ keys to change. Drive D: Local Disk, total size 34 GB
6. Close the Disk Administrator window. Drive E: Local (RAID) Disk, total size 104 GB
Drive F: Compact Disk

Figure 88: Hard Drive Menu Order

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 92
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Installing the IRS Operating System
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Windows NT Installation
1. Insert the IRS OS V3.1.0 CD into the CD-ROM drive (see Table 18 on page 93). Restart the IRS computer.
Table 18:

Part Number Description

4550 128 01492 IRS OS V3.1.0 CD

NOTE On the IRS computer with a Pentium 4 CPU there is a Pentium

4 sticker on the front of the computer. The new 73 GB 4 or 6
SCSI drives IRS with Xeon Processors is based on Pentium 4
will have a sticker advising on the 4 or 6 drives (see Figure 89).
If there is no sticker on the computer the CPU is probably
Pentium 3.
To verify the CPU type when the boot up window displays note
the type of CPU installed on the IRS computer: Pentium 3 or
Pentium 4 or Xeon processors. This information will be
required later in the IRS software installation.
2. When prompted Ready to begin ghost process select the option
according to your system configuration.
1 for Pentium 3 IRS computer
or
2 for Pentium 4 or Zeon processors IRS computer.
The Ghost installation starts automatically. If NT loads instead of the
Ghost, follow the instruction in Setting the Boot Devices on page 178.
3. When the installation is complete, a dialog box appears with the
message:
Eject CD-ROM and press CTRL+ALT+DEL to restart the computer.
Figure 89:
Eject the IRS OS V3.1.0 CD from the CD-ROM drive, and press CtrL+Alt+Del to restart the computer.
4. Press Ctrl+Alt+Del and Log on as administrator (password: mxroot).

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 93
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Installing the IRS Operating System
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Installing the Supplemental CD on the IRS

1. Insert the supplemental CD. Refer to Table 19 on page 94 for the correct CD for your system.
Table 19: Brilliance CT Supplemental CD

Part Number Description

4550 128 99401 BR 16-slice Supplem. CD V2.2.1.14009

4550 128 99411 BR 10-slice Supplem. CD V2.2.1.14009

4550 128 99481 BR 6-slice Supplemental V2.2.1.14009

4550 128 99461 4550 128 99461

4550 128 99471 Supplemental 10-Slice V4.2.1.14009

2. Installation window opens. Ensure

the Typical Supplemental
Installation option is selected.
Press Next.
3. Click Finish to close the
installation.
4. Eject the CD.

Figure 90:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 94
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Installing the IRS Operating System
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Drive Letters Modification

1. From the windows Start menu, select Programs > Administrative Tools > Disk Administrator.
2. At the message prompt click OK. A dialog box opens. Click Yes. The Disk Administrator window shown in Figure 91
on page 96 opens.
3. Verify that the drives are correctly assigned as follows:
NOTE The volume of Drive C: and Drive D: may slightly vary.
However, the total volume must be 38 GB for a 40-GB hard disk.
• Drive C: Local Disk, total size 4.1 GB
• Drive D: Local Disk, total size 34 GB
• Drive E: Local (RAID) Disk, active partition size 105 GB
• Drive F: CD ROM
4. If two drive letters must be switched, do the following:
a. Change the first incorrectly-labelled drive letter to an unassigned letter (see Figure 92 on page 96). Highlight the
disk to change.
b. Right-click and select Assign Drive Letter.
c. The Assign Drive Letter window opens. From the pull-down menu (see Figure 91 on page 96) assigning the disk
an unassigned drive letter.
d. Click OK to close the Assign Drive Letter window.
e. A confirmation window opens. Click Yes to confirm the change and close the window.
f. Repeat steps b on page 95 to e on page 95 and change the second drive letter to the correct disk letter.
g. Click OK to close the Assign Drive Letter window.
h. Repeat steps b on page 95 to e on page 95 to assign the correct letter to the first drive.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 95
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Installing the IRS Operating System
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Figure 92:

Figure 91: Disk Administrator Window

5. Close the Disk Administrator window.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 96
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Installing the IRS Operating System
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Installing the IRS Software

1. Insert the IRS CD into the CD-ROM drive (see Table 20 on page 97). The Philips Installation dialog box opens
automatically.
Table 20: Application Software CD Part Numbers

Part Number Description

4550 128 99521 IRS SW V4.2.1.1100

2. Click Start.

!
CAUTION Do not touch the mouse or the keyboard until the message Installation Completed appears at
the bottom of the Philips Install Supervisor window.
3. The Date and Time Properties window appears. Move the window away so you can see the Philips Install
Supervisor and wait for the Installation Completed message to appear on the bottom.
4. In the Time Zone tab set the correct time zone. Select your time zone from the list.
5. Click Apply.
6. Switch to the Date & Time tab and enter the correct time and date. Click OK.
7. In the Philips Install Supervisor window scroll through the list of Installed Components and verify that the Status for
all components is Done with exit code = 0x00000000.
NOTE If any of the exit codes are other than this value, return to Step 1 on page 97 and repeat this procedure.
8. Click Close.
9. Eject the CD.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 97
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Installing the IRS Operating System
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Installing the IRS Test Raws

1. Insert the IRS Add-on CD for your system (see Table 21 on page 98).
Table 21:

Part Number Description

1 4550 128 99491 16-Slice IRS Add-on V4.2.0.1/[Link]

2 4550 128 99501 10-Slice IRS Add-on V4.2.0.1/[Link]

3 4550 128 99511 6-Slice IRS Add-on V4.2.0.1/[Link]

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 98
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Installing the IRS Operating System
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

2. If the IRS AddOn wizard shown in

Figure 93 on page 99 does not
open automatically, double-click
My Computer on your desktop and
then double-click the CD drive.

Figure 93:

!
CAUTION In the next step click Cancel. DO NOT click Next.
3. The Installation Wizard window opens. Click Cancel, then click Yes and then Finish to close the wizard.
4. Double-click the Install_Test_Raws.vbs icon on the bottom left corner of the Desktop.
5. Wait for the install shield to finish.
NOTE Do not touch the keyboard before the message Installation Completed appears at the bottom of the Philips
Install Supervisor window.
6. The Installation window closes automatically when the process is complete.
7. Eject the CD.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 99
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Installing the IRS Operating System
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Installing Add-On BR/IDT Supplemental on the IRS

Install the Host Add-On BR IDT by completing the following procedure:

Part Number Description

4550 128 99541 BRIDT Suppl.V2.2.1/4.2.1.14016

1. Insert the CD labelled BRIDT Suppl.V2.2.1/

4.2.1.14016 into the CD drive.
2. In case the Philips MS IDT Upgrade wizard
shown in Figure 94 on page 100 does not open
automatically, double-click My Computer on
your desktop and then double-click the CD
drive.
3. Select IRS.
4. Click Next. The installation process begins.
5. Click Finish and eject the CD.

Figure 94: Philips MS IDT Upgrade

Time Sync
NOTE Perform this procedure when the Host software is completed.
1. On the desktop of the IRS double-click My Computer and navigate to C:\temp.
2. Double-click [Link]. The Command window appears.
3. After a few minutes the Command window closes automatically.
4. Restart the computer.
5. When the computer restarts use the new user name mx (no password needed).
6. Continue with System Calibrations and Performance Verifications on page 126.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 100
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Full CIRS Software Installation on a Two Server Configuration
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Full CIRS Software Installation on a Two Server Configuration

NOTE In this upgrade there are no Test Raws installation from separate CDs. The test RAWS will be installed in section
Add-on and Test Raws Installation on S1 Server on page 124.
If your system has a CIRS with one server configuration (Vertical Server) skip to CIRS Software Installation on a
Single Server (Vertical Server) Configuration on page 118.
This section covers installing both CIRS OS (Windows XP) and CIRS Application software on a two-server
configuration.
NOTE There are new IP addresses for the servers. The addresses are set automatically during install, and consist of the
following:

S1 (10/100/1000)[Link] Data link (10/100/1000) [Link] Diagnostics (the left port)

S2 (10/100/1000)[Link] Data link (10/100/1000)[Link] Diagnostics (the bottom port)

Before Installation

Check for a Service Partition

There is a service partition located on the C: drive only on the S2 server (P/N 4535-670-68911 or 4535-671-02401). If
you have the S2 server (P/N 4535-670-68911 or 4535-671-02401) check for a service partition by completing the
following procedure, otherwise proceed to Install Software on page 103:
1. From the Host PC, connect to each server using Remote Desktop.
2. On the server desktop click Start, then right-click on My Computer and select Manage.
3. Select Disk Management; you should see the first 39 MB on C:\ as a partition named "Service Boot".
4. If you have a service partition, proceed to Install Software on page 103. If there is no service partition, perform the
procedure Install Service Partition on page 102.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 101
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Full CIRS Software Installation on a Two Server Configuration
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Install Service Partition

1. Attach a monitor, keyboard, and mouse to the S2 server.
2. Insert the CD marked BRCT MX CIRS Service V4.2.4.13 into the server that you wish to install the service
partition.
3. Reboot the server:
a. Click Start > Shutdown, then click OK.
b. Click Yes on any messages that appear.
c. The server will then boot from the CD.
NOTE The next step formats drive C:\ and all data will be deleted.
4. When the menu appears, select the option Service partition restore.
5. This takes about 1 minute to complete. When finished, remove the CD.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 102
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Full CIRS Software Installation on a Two Server Configuration
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Install Software

!
CAUTION The CIRS Application installation automatically updates the Acquisitor and BP boards with the
new FPGA version during the software installation if needed.
Do NOT power down or reboot the server during the FPGA update. This could cause the board
to stop functioning. If the installation seems to take too long or appears to hang, please wait at
least 45 minutes after pulling out the CD from the original OS install before powering down the
server. Before powering down the system, connect a keyboard, monitor and mouse to diagnose
the problem.
1. The upgrade kit contains two copies of the CIRS OS CD:
a. Insert a copy of the CIRS V4.2.4.13 CD into the CD-ROM drive on S1.
b. Insert another copy of the CIRS V4.2.4.13 CD into the CD-ROM drive on S2.
2. Restart S1:
a. Press and hold the Power button on the Server S1 until the LED is off.
b. Press and release the Power button again.
3. Restart S2:
a. Press and hold the Power button on the Server S1 until the LED is off.
b. Press and release the Power button again.
4. Booting from the CIRS OS CDs will start the installation process. At this time data will be preserved, the hard disks
will be partitioned and formatted as necessary and the first stage of the Windows XP OS installation will copy
necessary Windows XP and CIRS installation files to the C: drive.
5. After approximately 10-20 minutes, the Servers will power down. If a server has not powered down after 20
minutes, there is an issue with the installation.
6. Power up the server and immediately remove the BRCT MX CIRS Service V4.2.4.13 CD.
7. The Windows XP installation will begin and take approximately 30 minutes to complete on each server. Once the
Windows XP installation finishes, the system will reboot, and the CIRS Application software will automatically be
installed. After approximately 5 more minutes, the system will power down. Once all two servers power down for the
final time, continue with Configure S2 on page 104.
4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 103
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Full CIRS Software Installation on a Two Server Configuration
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Configure S2
NOTE Before starting the configuration procedure pull out S2 and write down the Windows XP product key.
S2 Windows XP product key___________________________________________
1. Power on S2 by depressing and holding the switch on the front of the server until the green light to the left of the
switch illuminates.
2. After S2 powers up, wait three minutes, then use Windows Remote Desktop to connect to the S2 server.
3. Open CIRS folder on the Host PC Desktop or Service Laptop.
NOTE If the CIRS folder does not exist, create the Recon S-2 shortcut for the Remote Desktop as follows, otherwise
skip to Step f on page 107.

a. Press the Windows + R key combination.

b. In the Run window type in mstsc as shown in
Figure 95 on page 104.

Figure 95:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 104
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Full CIRS Software Installation on a Two Server Configuration
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

c. In the Remote Desktop Connection window enter

the IP address for CIRS server ([Link] as
the IP address for S2 as shown in Figure 96 on
page 105 and click the Options button.

Figure 96: Remote Desktop Connection (IP for S2)

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 105
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Full CIRS Software Installation on a Two Server Configuration
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

d. In the General tab, click the Save As... button as

shown in Figure 97 on page 106.

Figure 97: Remote Connection - General (IP for S2)

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 106
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Full CIRS Software Installation on a Two Server Configuration
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

e. Name the shortcut Recon-S2,

select Desktop in the left
pane and click the Save
button as shown in Figure 105
on page 113.

Figure 98:

f. Double-click the Remote Desktop icon Recon S-2.

g. Click OK at the security warning.
h. At the Log on prompt, log on as philips_service. Click OK.
4. If the hospital LAN uses the [Link] addresses you can use [Link] instead as described in Change
HOST - CIRS IP Addresses on page 181.
5. You will be prompted with a message "Do you want to identify the server by ejecting the CDROM drive?” Click
No.
6. The Windows Activation dialog appears. Enter the Windows XP Product Key located on the sticker attached to the
server.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 107
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Full CIRS Software Installation on a Two Server Configuration
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

7. You will be prompted to activate Windows XP. Select the second option (telephone activation) and follow the
activation instructions.
8. Following activation, an Internet Explorer window will display the CIRS installation status. Look for the "CIRS
Application Installation Completed!” message shown in Figure 99 on page 108, then close the window.

Figure 99: CIRS Application Installation Completed!

9. Power off the server:

a. Right-click on the Windows Taskbar, and select

Task Manager.
b. In the Task Manager window, click Shut Down >
Turn Off as shown in Figure 100 on page 108.
c. Click Yes on any messages that appear.
d. Click OK on the Remote Desktop Disconnected
prompt.

Figure 100: Task Manager Shut Down Menu

NOTE During shutdown, the Remote Desktop connection will automatically disconnect and return you to the Host
desktop.
10. Power on the server by depressing and holding the switch on the front of the server until the green light to the left of
the switch illuminates.
11. Verify the 3DBP driver is correctly updated as follows:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 108
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Full CIRS Software Installation on a Two Server Configuration
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

a. If you created a Recon S-2 Remote Desktop

shortcut on the Desktop in Step 3 on page 104,
double-click it. If not, open the CIRS folder and
double-click the Recon S-2 Remote Desktop
shortcut there.
b. Click OK at the security warning.
c. At the Log on prompt, log on as philips_service.
Click OK. Figure 101: VHDL Revision for S2
d. On the CIRS S2 desktop double-click the NOTE This figure is for illustration only.
3DBPdiag icon.
e. Verify the Hardware VHDL Revision is the same
as the version listed in Figure 101 on page 109
NOTE If the version is not correct or does not show
up, follow the procedure Manually Updating
the 3DBP Device Driver on page 188.
12. Continue with Configure S1 on page 110.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 109
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Full CIRS Software Installation on a Two Server Configuration
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Configure S1
NOTE Before starting the configuration procedure pull out S1 and write down the Windows XP product key.
S1 Windows XP product key___________________________________________
1. Power on S1 by depressing and holding the switch on the front of the server until the green light to the left of the
switch illuminates.
2. After S1 powers up, wait three minutes, then use Windows Remote Desktop to connect to the S1 server.
3. Open CIRS folder on the Host PC Desktop or Service Laptop.
NOTE If the CIRS folder does not exist, create the Recon S-1 shortcut for the Remote Desktop as follows, otherwise
skip to Step f on page 113.

a. Press the Windows + R key combination.

b. In the Run window type in mstsc as shown in
Figure 102 on page 110.

Figure 102:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 110
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Full CIRS Software Installation on a Two Server Configuration
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

c. In the Remote Desktop Connection window enter

the IP address for CIRS server ([Link] as
the IP address for S1 as shown in Figure 103 on
page 111 and click the Options button.

Figure 103: Remote Desktop Connection (IP for S1)

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 111
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Full CIRS Software Installation on a Two Server Configuration
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

d. In the General tab, click the Save As... button as

shown in Figure 104 on page 112.

Figure 104: Remote Connection - General (IP for S1)

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 112
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Full CIRS Software Installation on a Two Server Configuration
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

e. Name the shortcut Recon-S1,

select Desktop in the left
pane and click the Save
button as shown in Figure 105
on page 113.

Figure 105:

f. Double-click the Remote Desktop icon Recon S-1.

g. Click OK at the security warning.
h. At the Log on prompt, log on as philips_service.
i. Click OK.
4. If the hospital LAN uses the [Link] addresses you can use [Link] instead as described in Change
HOST - CIRS IP Addresses on page 181.
5. You will be prompted with a message "Do you want to identify the server by ejecting the CDROM drive?” Click
No.
6. The Windows Activation dialog will appear. Enter the Windows XP Product Key located on the sticker attached to
the server.
4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 113
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Full CIRS Software Installation on a Two Server Configuration
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

7. You will be prompted to activate Windows XP. Select the second option (telephone activation) and follow the
activation instructions.
8. Following activation, an Internet Explorer window will display the CIRS installation status. Look for the "CIRS
Application installation completed” message, then close the window.
9. Enable Supervisor service on S1 as follows:
a. On the Desktop, double-click the Services icon.
b. Right-click on CIRS Supervisor Service, and
select Properties. The CIRS Supervisor Service
Properties window appears.
c. Change Startup type to Automatic.
d. Click Apply, then click OK.
e. Close the Services window.

Figure 106:
10. Power off the server:
a. Right-click on the Windows Taskbar, and select Task Manager.
b. On Task Manager, click Shut Down > Turn Off as shown in Figure 100 on page 108.
c. Click Yes on any messages that appear.
d. Click OK on the Remote Desktop Disconnected prompt. During shutdown, the Remote Desktop connection will
automatically disconnect and return you to the Host desktop.
11. Power on the server by depressing and holding the switch on the front of the server until the green light to the left of
the switch illuminates.
4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 114
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Full CIRS Software Installation on a Two Server Configuration
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

12. Verify the ACQ driver is correctly updated as follows:

a. If you created a Recon S-1 Remote Desktop
shortcut on the Desktop in Step 3 on page 110,
double-click it. If not, open the CIRS folder and
double-click the Recon S-1 Remote Desktop
shortcut there.
b. Click OK at the security warning.
Figure 107: Hardware VHDL Revision S1
c. At the Log on prompt, log on as philips_service.
d. Click OK.
e. On the CIRS S1 desktop double-click the ACQdiag
icon.
f. Verify the Hardware VHDL Revision is the same as
in Figure 107 on page 115:
NOTE If the version is not correct or does not show
up, follow the procedure Updating the
Acquisition Device Driver on page 185.
13. Verify the Time Zone is set correctly:
a. From the Host computer remotely connect to the CIRS S2.
b. Click Start > Control Panel > Date,time,language,and Regional Settings > Time and Date.
c. Select the Time Zone tab and check the Time Zone.
NOTE If a change was made to the Time Zone and click Apply to complete the Time Zone change.
d. Verify the time of the server is the same as the Host. Select the Date & Time tab and change the setting if
necessary.
e. Select the Internet Time tab and verify the Automatic Synchronize option is not selected.
NOTE There MUST be date and time synchronization between the Host computer and CIRS servers so that the time-
stamp on the image is identical to the time displayed on the Host computer system tray.
14. From S2 computer perform the following sub-procedure:
a. Open Windows Explorer and navigate to C:\Program Files\Philips\CIRS.
b. Double-click [Link].

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 115
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Full CIRS Software Installation on a Two Server Configuration
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

c. Close Windows Explorer

15. Power off the server:
a. Right-click on the Windows Taskbar, and select Task Manager.
b. On Task Manager, click Shut Down > Turn Off as shown in Figure 100 on page 108.
c. Click Yes on any messages that appear.
d. Click OK on the Remote Desktop Disconnected prompt.
NOTE During shutdown, the Remote Desktop connection will automatically disconnect and return you to the Host
desktop.
e. Power on the server by depressing and holding the switch on the front of the server until the green light to the left
of the switch illuminates.
16. Repeat the above Step 13 on page 115 to Step 15 on page 116 for CIRS S1
17. The CIRS Application software is now installed. If the Scanner Application is running on the Host, log off and
restart it before attempting any reconstructions.
18. Continue with Two Server Configuration Setting on page 117.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 116
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Full CIRS Software Installation on a Two Server Configuration
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Two Server Configuration Setting

1. Using Windows Remote Desktop, connect to S1:
2. If you created a Recon S-1 Remote Desktop shortcut on the Desktop in Step 3 on page 110, double-click it. If not,
open the CIRS folder and double-click the Recon S-1 Remote Desktop shortcut there.
3. Click OK at the security warning.
4. At the Log on prompt, log on as philips_service.
5. Click OK.
6. Double-click on the 2-ServerCFfg icon on the S1 Remote Server Desktop; a command window opens with the
message Value NumberofNodes exists, overwrite? (Y/N). Press y and <Enter>. The command window closes.
Continue to Add-on and Test Raws Installation on S1 Server on page 124.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 117
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 CIRS Software Installation on a Single Server (Vertical Server) Configuration
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

CIRS Software Installation on a Single Server (Vertical Server)

Configuration

NOTE To switch the KVM to the Vertical Server connection, press the Ctrl key twice.
This section covers installing both CIRS OS (Windows XP) and CIRS Application software on a single-server
configuration.
During the installation, new IP addresses are assigned automatically. They are as follows:

Table 22: New IP Addresses

S1 (10/100/1000)[Link] Data link (10/100/1000) [Link] Diagnostics (the left port)

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 118
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 CIRS Software Installation on a Single Server (Vertical Server) Configuration
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Installing the Software

!
CAUTION The CIRS Application installation automatically updates the Acquisitor and BP boards with the
new FPGA version during the software installation if needed. Do NOT power down or reboot the
server during the FPGA update. This could cause the board to stop functioning. If the installation
seems to take too long or appears to hang, wait at least 45 minutes after removing the CD from
the original OS install before powering down the server. Before powering down the system,
connect a keyboard, monitor and mouse to diagnose the problem.
NOTE The upgrade kit contains two copies of the CIRS OS CD.
Proceed as follows:
1. Insert one copy of the BRCT MX CIRS V4.2.4.13 (4550 128 04571) CD into the CD-ROM drive on S1.
2. Restart the S1 Server.
a. Press and hold the Power button on the Server S1 until the LED is off.
a. Press and release the Power button again.
NOTE Booting from the CIRS OS CDs will start the installation process. At this time data will be preserved, the hard
disks will be partitioned and formatted as necessary and the first stage of the Windows XP OS installation will
copy necessary Windows XP and CIRS installation files to the C: drive.
3. After approximately 10-20 minutes, the Server will power down. If the server has not powered down after 20
minutes, there is an issue with the installation.
4. Power up the server and immediately remove the BRCT MX CIRS V4.2.4.13 (4550 128 04571) CD. The Windows
XP installation will begin and take approximately 30 minutes to complete.
5. Once the Windows XP installation finishes, the system will reboot, and the CIRS Application software will
automatically be installed. After approximately 5 more minutes, the system will power down.
6. Continue with Configure S1 on page 120.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 119
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 CIRS Software Installation on a Single Server (Vertical Server) Configuration
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Configure S1
NOTE Before starting the configuration procedure pull out S1 and write down the Windows XP product key.
S1 Windows XP product key___________________________________________
Configure S1 as follows:
1. Power up the CIRS S1 Server.
2. Log on as philips_service.
3. Click OK. The message "Do you want to identify the server by ejecting the CDROM drive?" appears.
4. Click No. The Windows Activation dialog box appears.
5. Enter the Windows XP Product Key you wrote down (the Product Key is located on the sticker attached to the
Server).
6. Select the second activation option (telephone activation) and follow the activation instructions. An Internet
Explorer window appears and displays the CIRS installation status.
7. Wait for the "CIRS Application installation completed" message, and then close the window.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 120
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 CIRS Software Installation on a Single Server (Vertical Server) Configuration
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

8. Enable Supervisor service on S1 as follows:

a. On the Desktop, double-click the Services icon.
b. Right-click on CIRS Supervisor Service, and
select Properties. The CIRS Supervisor Service
Properties window appears.
c. Change Startup type to Automatic.
d. Click Apply, then click OK.
e. Close the Services window.
9. Restart the CIRS S1 Server:
a. Select Start > Turn off computer.
b. Click Restart.

Figure 108:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 121
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 CIRS Software Installation on a Single Server (Vertical Server) Configuration
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

10. Verify the 3DBP driver is correctly updated as follows:

a. Log on as philips_service. Click OK.
b. On the CIRS S1 desktop double-click the
3DBPdiag icon.
c. Make sure that the Hardware VHDL Revision is the
same as in Figure 109.
NOTE If the version is not correct or does not show Figure 109:
up, follow the procedure described in Manually
Updating the 3DBP Device Driver on page
188.
d. Click Quit.
11. Verify that the ACQ driver is correctly updated as
follows:
a. On the CIRS S1 desktop double-click the ACQdiag
icon.
b. Verify the Hardware VHDL Revision is the same as
Figure 110. Figure 110:
c. Click Quit.

NOTE If the version is not correct or does not show up, follow the procedure Updating the Acquisition Device Driver on
page 185.
12. In the event that the hospital LAN uses the [Link] IP addresses, you can use [Link] (change the IP
address for S1according to the instructions in Change HOST - CIRS IP Addresses on page 181).
NOTE If needed log on as philips_service.
13. Verify the Time Zone is set correctly as follows:
a. On the CIRS S1 computer, click Start > Control Panel.
b. Click Date, time, language, and Regional Settings.
c. Click Date and Time.
d. Select the Time Zone tab and check the Time Zone.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 122
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 CIRS Software Installation on a Single Server (Vertical Server) Configuration
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

NOTE If a change was made to the Time Zone, click Apply to complete the Time Zone change.
e. Verify the time of the Server is the same as the Host. Select the Date and Time tab and change the setting if
necessary.
f. Select the Internet Time tab and verify the Automatic Synchronize option is not selected.
NOTE There must be date and time synchronization between the Host computer and CIRS Servers so that the time-
stamp on the image is identical to the time displayed on the Host computer system tray.
14. From CIRS S1 computer, perform the following sub-procedure:
a. Open Windows Explorer and navigate to C:\Program Files\Philips\CIRS.
b. Double-click [Link].
c. Close Windows Explorer.
15. Restart the CIRS-S1 Server (select Start > Shutdown > Restart and click OK).

Single Server Configuration Setting

Proceed as follows:
1. If your are not on S1 use the KVM (press the Ctrl key twice) to switch to S1.
2. On the S1 desktop double-click on the 1-ServerCfg icon. A cmd window appears with the message “Value
NumberofNodes exists; overwrite? (Y/N)” displayed.
3. Press Y and then press Enter. The cmd window closes.
4. Continue to Add-on and Test Raws Installation on S1 Server on page 124.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 123
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Add-on and Test Raws Installation on S1 Server
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Add-on and Test Raws Installation on S1 Server

NOTE (For a Two-Server Configuration only) Ensure that Server S2 is turned ON before continuing; failure to do so will
result in incorrect software installation.
1. If your are not connected, connect to S1 (or log on to the S1 Vertical Server using the KVM switch).
2. Install CIRS Add-on for S1. Insert the appropriate CD:
Table 23:

1 4550 128 99441 IDT/BR 16 CIRS AddOn V2.2.0.5

2 4550 128 99451 IDT/BR 10 CIRS AddOn V2.2.0.5

3 4550 127 01931 IDT/BR 6 CIRS Addon V2.2.1.1938

NOTE If the InstallShield menu does not appear, open Windows Explorer and double-click the CD drive. If a folder
opens run the CIRS_addOn_IDT10.msi or CIRS_addOn_IDT16.msi file.

3. When the wizard opens, click Next.

4. Make sure that the CIRS Add-On is
selected.
5. Click Install.
6. If the Add-On installation is completed
message appears, click OK.
If the wizard closes without the message,
insert the CD again and when the wizard
begins again, click Next.
7. Select Test Raws and click Install.
8. When the “Test Raws installation is
completed” message appears click OK,
then Quit, Yes and Finish. Figure 111:
9. Eject the AddOn CD.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 124
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Add-on and Test Raws Installation on S1 Server
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

NOTE For a Vertical Server, click Start > Turn Off the
Compu‘ter. In the window that opens, click Turn Off,
then skip to Step 11 on page 125.
10. Restart the CIRS S1 Server.
a. Right-click on the Windows Taskbar, and select Task
Manager.
b. In the Task Manager window, click Shut Down > Turn Off as
shown in Figure 112 on page 125.
c. Click Yes on any messages that appear.
d. Click OK on the Remote Desktop Disconnected prompt. Figure 112: Task Manager Shut Down Menu

NOTE During shutdown, the Remote Desktop connection will automatically disconnect and return you to the Host
desktop.
11. Power on the server by depressing and holding the switch on the front of the server until the green light to the left of
the switch illuminates.
The CIRS Application software is now installed. If the Scanner Application is running on the Host, Log off and
restart it before attempting any reconstructions.
12. Log on as philips_service.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 125
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 System Calibrations and Performance Verifications
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

System Calibrations and Performance Verifications

1. From Home > Service > Tube Conditioning run the Short Tube TC.
2. When upgrading from 6/10 slice configurations from V1.2.5/3.2.5 perform all physics calibrations according to
BR CT_IDT Performance Procedure-Multiple Versions in the InCenter.
3. Perform Air calibration for all modes.
4. Verify system performance according to BR CT_IDT Performance Procedure-Multiple Versions in the InCenter.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 126
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 System Calibrations and Performance Verifications
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Backup System Parameters

1. Insert a formatted EOD into the EOD drive.

2. Launch the Backup/Restore application: double-click
Backup/Restore icon on the Desktop.
3. Select the Backup tab.
4. Click Browse and navigate to Drive F: (EOD), select the
backup directory with the most recent date and click OK.
5. In the Backup dialog box, verify all options (check boxes) are
selected as shown in Figure 113 on page 127.
6. Click Start Backup.

Figure 113:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 127
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 System Calibrations and Performance Verifications
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

7. When the backup is complete a message appears,

click OK as shown in Figure 114 on page 128.
8. Scroll up the log and look for errors in the Log
window shown in Figure 115 on page 128 (the
Backup Done message appears even if the
backup was not successful).

Figure 114: Backup Done Prompt

9. Click Close in the Log window.
10. Click exit in the Backup/Restore window shown in
Figure 113 on page 127.
11. Eject the EOD.

Figure 115:

Final Checks
1. Log off and restart the Host.
2. Log on as CT.
3. Run a few scans using the Customer protocols.
4. If there is an IBox run a few Cardiac and/or Pulmo scans.
4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 128
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Installing FCO 72800440
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Installing FCO 72800440

Downloading the ISO File for FCO 72800440 from the InCenter
The following steps lead you through the process of accessing and downloading the ISO image from the Philips
Intranet.
1. Connect to the Philips network (IST).
2. Navigate to the InCenter webpage Service Library > Computed Tomography > Brilliance Series > Brilliance 6/
10/16 (Water)| Support > FCO
3. Open the FCO72800440 – ROF – V2.2.1/4.2.1 Pediatric Filter Fix page.
4. Click the ISO file.
The File Download window opens.
5. Click Save to save the file.
The Save As window opens.
6. Select the folder on your hard drive where you want to save this file.
TIP Make a note of where you save the file for creation of the CD in the next section.
7. Click Save. The file downloads and is saved at the selected location.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 129
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Creating the Utility CD
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Creating the Utility CD

NOTE Make sure the file you downloaded is on your PC.

Create a CD using Roxio Easy CD Creator

1. On the Windows Desktop of your laptop computer double-click the CD Creation software icon .
The Easy CD Creator application opens.
2. On the menu bar click File > Make a data CD.
The Record CD from Hard Disk Image window appears.
3. Navigate to and select the file you downloaded.
4. Click Open.
The Record CD Setup window appears.
5. Click Start Recording.
The Record CD Progress window appears. The progress of the CD recording process is displayed.
When the process is complete, the Progress and Disc Progress bars display 100% and the message CD created
successfully appears.
6. Click OK.
The Create a Label window opens.
7. In the text box type the label name Utility CD.
8. Click Yes to close the window.
9. Close the Easy CD Creator by clicking File > Exit. from the menu bar.
10. Continue to Installing the IDT Supplemental (Pediatric Filter Change) CD on page 132.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 130
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Creating the Utility CD
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Create a CD using Sonic

1. On the Windows Desktop of your laptop computer double-click the Sonic icon . to open the Sonic application.
(Figure 116).
2. Click Data Disk (Figure 117).

Figure 116: Sonic Application - Select Data Disk Figure 117: Sonic Application - Add Files

3. Click Add files and folders.

4. Navigate to and select the file you downloaded and click Add.
5. In the Volume Label drop down window type the label name Utility CD.
6. Click the Burn button.
The CD recording is finished when the Progress bar is 100%, the message Your disk was created successfully
appears and the CD ejects.
7. Click Done
8. Close Sonic.
9. Remove the CD from the laptop and close the drive.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 131
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Installing the IDT Supplemental (Pediatric Filter Change) CD
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Installing the IDT Supplemental (Pediatric Filter Change) CD

1. Log on as philips_service.
2. Insert the CD into the CD/DVD-ROM/ drive of the Host computer.
NOTE If the installation window does not appear, double-click My Computer, and then double-click the IDT V2.2.1_4.2.1
drive icon.
3. The Philips_MS_IDT_Upgrade Installation window opens.
4. Click Next.
NOTE Wait while the files are being installed.

Figure 118: IDT Upgrade CD Installation

5. When the installation is complete, click Finish.
NOTE The installation window closes and a cmd window appears and quickly disappears (do not do anything). Wait until
the Installation Validation window appears.
6. Make sure that the Installed Version is:
4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 132
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Installing the IDT Supplemental (Pediatric Filter Change) CD
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

• For Mx8000 IDT - 4.2.1.14022.

• For Brilliance CT - 2.2.1.14022.
7. Click OK to close the Installation Validation window.
8. Eject the CD.

Figure 119: Installation Completed

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 133
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Application Release Notes
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Appendix A: Application Release Notes

This section includes the application release notes for the following versions:
• Brilliance (Water-Cooled) Version 2.0.2 and Mx8000 IDT V4.02 Application Release Notes on page 134
• Brilliance (water-cooled) Version 2.2.1 and Mx8000 IDT V4.2.1 Application Release Notes on page 148

Brilliance (Water-Cooled) Version 2.0.2 and Mx8000 IDT V4.02

Application Release Notes

New Features
This version includes the following changes:
• Scan angle parameter in the protocol:
• In Head scans, Scan angle of 360/420 can be selected in Generate Protocols mode. This applies to all Head
scan-types.
• Scan angle of 240 is automatically applied by the rules system to specific scans like locator and tracker.
• FOV for Surview may be set by the user.
• New cardiac factory protocols for the Cardiac option
• Report options are available
• Image quality for scanners: 10 slices in 8x3mm mode and for 6 slices in 6x3 mode, was improved – splay artifacts
were reduced.
• Remote Recon option can be used (EBW V2.0.52)

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 134
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Application Release Notes
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Work Flow
• Integration of EBW 2.0 into the Scanner Console
• Enhanced Plan on Surview, including additional reconstructions and MPRs.
• Enhanced graphic planning on Surview for easier and faster operation. Mouse cursor automatically changes its
shape according to the desired operation:

Move the Scan - move mouse cursor into the middle of scan plan box (not over one of the scan’s borders),
then click and drag the scan plan box to the desired position.
Change Start/End - move mouse cursor to beginning or end of scan, then click and drag the line up or
down.
Change Field of View – move mouse cursor to the scans side borders, then click and drag the line left or
right.
Rotate the Scan (Axial and MPRs only) – move mouse cursor over the Rotate icon above the scan
rectangle, then click and drag the mouse left or right.
Resize Plan – move the mouse is over a corner of the plan contour, then click and drag the corner to
change the corner position. This changes the start, end, length, FOV, or X/Y shift. When dragging the
corner, the FOV does not change symmetrically

MPR planning
• During the Plan Scan stage – after the reconstruction is complete, the CT Viewer is launched and the MPR images
are displayed.
• Add an MPR: click on a scan in Series list during Plan Scan stage and click “Insert MPR” button. The MPR is
inserted after the selected series. The MPR “RAW images” are derived from the recon before it.
• Set MPR parameters: Click on the MPR in Series list to view the MPR parameters.
• Change the MPR’s length and FOV: can be done graphically.
NOTE The middle of MPR must always be within the scan’s boundaries.
• Orientation: there are three ways of determining MPR orientation.
Orientation buttons: Sagittal / Coronal / Axial buttons sets the MPR direction and uses maximum scan volume.
Sagittal angle and Coronal angle: parameter in scan protocol. Range is –90 to +90.
Graphic interface to Rotate the MPR: When using a Surview 180, the Sagittal angle can be rotated. When
using Surview 90, the Coronal angle can be rotated.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 135
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Application Release Notes
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

NOTE Using both angles on single Surview can be confusing and is not recommended.
NOTE When using both angles, the plan box (blue filled rectangle) is used to manipulate MPR (Move, change F.O.V. etc.)
• Viewing MPR images: After all images are reconstructed MPR images are automatically loaded into the
CT Viewer.
• Batch: range can be edited by using the “insert” and “delete” buttons in the keyboard
NOTE To save the MPR series, right click on the series name, and select “save” or “film”. Images are not automatically
saved.
• Interactive series list (in the toolbox): controls both planning the scans on the Surview and viewing the images
on the Scan Viewer.
Click on a Series to plan it (in Plan Scan mode) or to View the images (in View Scan mode).
Copy, Paste and Delete scans and recons directly from series list during planning and viewing.

Split study
• Define a different Requested Procedure for each series of a study.
• Set Requested Procedure in the Auto Options tab of a scan or an Add-Recon.
• For multiple scan studies, select the new Requested Procedure to create a separate study in Archive with a
different Requested Procedure for each scan.
• Each archive study will have the selected Series for the Requested Procedure and all the studies will have the
Surview images.
NOTE Requested Procedures should be set up during installation.

Merge Two series

• Merge series into one, for PACS review
• Select “Merge with Previous Series” in the Auto Options tab of a scan or an Add-Recon.
• Select “Merge with Previous Series” to merge the selected Series with the preceding Series. Both Series will have
consecutive numbering; the 2nd Series number will start after the previous Series last image number.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 136
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Application Release Notes
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Continue Last Study

• This option appears in the Patient Data window and is available if Patient Parameters are identical to those of the
previous Patient.
• Select this option if previous study was mistakenly stopped. New scans will have the same Study number in
Archive.
• Select Last Exam Protocol: Click this button to use the last used Exam protocol of the last study.

Use Previous Surview Image

• This button appears on the Clinical tab of the Toolbox in Plan Scan mode of a Surview image.
• Click Use Previous Surview Image to use the last Surview performed on this patient.

Integrated HIS/RIS
• Modify patients’ details in HIS/RIS using Web Interface or Telnet Interface.
• Click the Direct HIS/RIS quick access button in the Home page to open the HIS/RIS window.
NOTE HIS/RIS should be defined once using Preferences

Auto Create Es Image as Secondary Capture (for Pacs Review)

In Preferences > Scanner, select Autosend ES images as secondary capture = Yes. ES images will be
automatically sent to PACs as a secondary capture.

Block Transfer of Certain Type of Images

This feature enables filtration of the images according to different flags or tags while exporting them from the scanner to
the PACS. This reduces the images load on the PACS by avoiding transfer of unnecessary images.

Import Procedure List From His/ris for Mapping

Required Procedure imported from His/Ris

New “Archived” Flag in Directory

This feature is configured in the system configuration. Images sent to the different media (except EOD) appear with
flag.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 137
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Application Release Notes
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Pulmo Instructions
• To plan two Pulmo Prospective scans using different scan modes (for instance "max inhale" and "max exhale")
perform the scans as follows:
1. Plan the first scan in the max. inhale mode and click Go.
2. When the scan is complete plan the second scan in the Max. Exhale mode.
3. Click Go.
NOTE Do not plan the two scans simultaneously.
• To avoid reconstruction failure due to invalid pitch, always keep the pitch values within 0.04 - 0.08 and the rotation
time 0.4 or 0.5 sec. The factory recommended values are: Pitch = 0.06 and RT = 0.5 sec.
• The Varian sensor is not supported. The only supported sensor is Bellows.
• Never edit the R tags on-line. After the scan and reconstruction are finished, end the study and only then perform R-
tag editing for the off-line reconstruction. If the peak is not identified use the "Add new tag" function. Editing the last
R-tag doesn't work.
• The message "Respiratory device is disconnected" may appear during the Pulmo scans, even when the device
is performing correctly. When this message appears make sure that the device is connected. If it is disconnected,
abort the scan.

Easy protocols
• Clinically oriented scanning: a new parameter called Scan Type is used to avoid erroneous parameters.
• Parameters that may result in bad image quality are not available.
• Automatic parameters: parameters are optimized automatically according to the scan type.
• Improved protocol interface: a new design offers more intuitive operation.

Bolus Tracking Enhancements

• Automatic vessel tracking for improved triggering when following the vessel movements.
• Improved tracker image quality: 512 matrix

Pulmonary Gating Option

• Trigger a scan at a particular breath level: prospective scan at different breath phases.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 138
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Application Release Notes
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

• Improved image quality by reducing the motion artifacts caused by patient’s breathing.

Cardiac Irregularities (R Tag Correction) in Retrospective Tagging

• Improved image quality of cardiac scans by adding, deleting or adjusting the R tags on the ECG graph before final
recon.

Cardiac Adaptive Filter

• A new algorithm dedicated to Cardiac scans, replaces the regular Adaptive Filter for Cardiac scans.
• Activated from the Advanced tab of a Cardiac scan: same checkbox as normal Adaptive Filter.
• In order to control the adaptive filter in the scan protocol, in the Preferences window clear the Automatic Special
Filters selection.

Adaptive Filter
• Select to activate a special algorithm that improves image quality of Axial & Helical scans.
• Available in the Advanced tab of a scan.
• In order to control the adaptive filter from the scan protocol, in the Preferences window clear the Automatic Special
Filters selection.

Recon Image Enhancement

Recon Image enhancement may be set in the scan protocol. The enhanced image may be viewed on external devices
as it appears on the scanner viewer.

Shifted CT scale
• The CT scale is shifted down by 24 Hounsfield units as shown below.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 139
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Application Release Notes
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

• The upper 24 Hounsfield units are lost in favor of low-end 24 Hounsfield units.

Figure 120: CT Scale Shift

Issues fixed in Brilliance V2.0.2/4.0.2

The following corrections and improvements were implemented in version 2.0.2/4.0.2:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 140
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Application Release Notes
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

• Annotations in MIP MasterCut

• LNA option – volume calculation accuracy
• BolusPro reliability improvements
• Fix patient data improvements
• HIS/RIS window is no more hidden behind other windows
• Cardiac viewer fixes
• DLP (Dose-Length product) display for short spiral scans accuracy
• Split-study is a key-enabled option
• Long TC crash on arcing
• Bug and Irregularities
• Reconstruction with SP Off
The reconstruction with SP off is now allowed. Although Philips recommends reconstructing with the SP on, in some
cases where the speed of the scan is crucial for the success of the scan, the SP may be turned off.
This applies to the Ultra Fast mode where the DFS is not used, and as a result the in-plane resolution decreases when
the SP is on and/or the pitch is higher than 1.
Consequently, in order to optimize the reconstruction quality in these scans, you may wish to turn-off the SP. However,
if the scan mode is Ultra-Fast and the needed scan speed is so fast that the actual pitch is higher than 1, the SP should
be on since the in-plane resolution will anyway be low.
To summarize the recommended SP status, see the table below:

Pitch UF Std. HR UHR

<1 OFF ON ON ON

(CIRS systems) ON
>1 ON ON
(IRS systems) NA
NA

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 141
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Application Release Notes
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Scanner Operation Cautions and Warnings

!
CAUTION

• During Bolus tracking, pay attention to the CT values on images.

• To start the clinical scan manually, click the Start Clinical scan button.
• When using SAS injector — start the injection only after the message “Start Injection” appears
on the scanner screen.
• Perform daily and monthly scanner checks to ensure correct CT numerical values.
• Keep the Maylar clean at all times. Any contrast material left on the Mylar surface, patient
table, and accessories will create image artifacts. (see instructions in the section Cleaning the
System).
• When Automatic dose-right ACS is used — always review the mAs value before scanning.
• When a Decubitus position is used, review Surview scan angle. When using a Decubitus
position use 90° for AP and PA and 180° for Lateral.
• While working in the scanner room, be aware of cables that may be lying on the floor around
the Gantry.
• A doctor must sign reports used for Interventional operations.

WARNING Biopsy CCT

• The doctor must avoid infecting the patient; do not touch the panel or any other
surface that is not sterile.
• Ask the assistant to operate the panel.
• Use disposable sterile gloves.
• Perform operations on the console according to the biopsy operator’s instructions.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 142
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Application Release Notes
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

!
WARNING Additional or off-line reconstruction

• Don’t use 7.5 mm slice thickness in Additional or Off-line reconstruction if the scan
was acquired with 6x3 mm or 8x3 mm collimation and the original slice thickness
was 3.3 mm.

!
CAUTION Uninterruptible Power Supply (UPS) will supply power to the console for approximately 10 to 15
minutes when there is a power failure. To improve system security against program viruses, the
UPS does not send messages (time left on UPS power or shut down) to the user. The user must
quickly complete the reconstruction for the last scan and then safely shut down the Host and IRS
computers.

Open Issues

Guidelines and Operation Instructions

Scanning
• When scanning without a Surview – Don’t use * as the start position; enter a number.
• If the Start Study button does not respond, wait 30 seconds. If still not responding, try clicking the Home button
and then click Start Study again.

Bolus Tracking
• Don’t move the patient table after clicking Go for the Locator scan.

Interventional CCT
• Lasers are not turned off automatically after clicking End Study. Turn Lasers off manually.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 143
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Application Release Notes
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

• In order to view previous CCT images – click on the series list.

• Start pressing the pedal only after “Press Pedal To Scan” message is displayed on the screen.
• When using CCT Single mode, move the bed only using the Gantry panel or the CT box.
NOTE If the table height & tilt are changed during the scan, image parameters will not be updated.

Cardiac
• Do not use Continue Current Series option in Cardiac scans.
• Do not auto launch to cardiac viewer if cardiac viewer is already open.
• Do not use the ECG button on tool box
• Use Adaptive Filter in all cardiac scans as follows:
• Large protocol: Adaptive filter + CB filter
• Routine CCTA protocol: Adaptive filter + CC filter
• Stent protocol: Adaptive filer + CD filter

TLCT

• The actual cycle time may differ from the planned cycle time up to 0.5 seconds.

Pulmo
• Use of Re-Recon creates images that don't belong to the required phase. In order to reconstruct the desired phase
only use the Off-line reconstruction.

Offline Reconstruction
• Sometimes it takes up to 20 seconds until the Reconstruction editor opens after selecting View Recon.

Archive – Sub Selection

• Split option in sub-selection window doesn’t work.
• Don’t use Sub-selection when mixed series are selected.
• If the reference surview appears gray, re-select the requested series in the archive without surview images.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 144
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Application Release Notes
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

General
• Restart the host console every day.
• Before using Generate Protocols or Air calibration, click Start Study and make sure the patient data fields are
empty.
• Make sure the EOD media is always inserted into the EOD slot, even if it is not used for backup.
• Stereotaxis: use only spiral protocols with SP reconstruction or Axial protocols. If you are using axial protocols,
select only the following collimations:
• For 16 and 10 slices configuration: 4x0.75, 4x1.5 or 4x3.
• For 6 slices configuration use 3x1.5mm or 3x3mm images obtained from 6x0.75mm or 6x1.5mm collimation
respectively.
• “Unhandled Exception” error message– if this dialog box appears, click Quit and Logout. Do not continue
working after an Unhandled Exception appeared.
• Dental CT Application: only images with matrix 512x512 can be loaded to the application. In case the Dental
images have higher matrix, perform offline recon with matrix 512.
• Cursor coordinates value on Surview may not be accurate, don’t use them for measuring or positioning.

Common IRS (CIRS) Guidelines

• The toolbox state messages might not be synchronized (messages such as: Scanning, Reconstruction, Acquisition
complete).
• The numbers of images left for reconstruction on the scan viewer might not be accurate.
• If CIRS was disconnected or turned off for any reason, Logoff and then Logon the console before scanning (for
systems with CIRS).

Application Limitations

Quick Review
• Unable to open RF or CR modality images
Workaround: Open the images in the Viewer application

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 145
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Application Release Notes
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Lung Nodule Assessment (LNA)

• After segmenting a nodule it is impossible to edit the contours on the original images.

States
State doesn't include the following features:
• User graphics including QCTA tool graphic elements
• Sculpting
• Bone removal
• Batch/cine
• Rendering parameters (protocols)
• User-defined stent measurements
• CCTA states containing multiple phases does not support loading bookmarks saved in scenes other than Cage
Removal.
• AVA Stent Planning stage

Workarounds for Known problems

• When loading to the CCTA application, the window is gray.
Solution: left click the mouse on the window.
• In Archive manager it is impossible to access a remote EOD after formatting.
Solution: transfer data locally to the formatted EOD before trying to access the remote EOD.
• Archive manager gets stuck (does not respond).
Solution: Press keyboard Alt + Tab (Quick Review) and check if an open application or dialog box is hiding behind
the Archive Manager window.
• Loading large matrix images: the Preview application can open up to 1700 images at a resolution of 512x512.
When opening larger matrix images, a reduced number of images are allowed.
Solution: Open up to 850 images of 768x768 matrix and up to 425 images of 1024x1024 matrix.
• HIS-RIS hides is behind the main window
Solution: Click on home page

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 146
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Application Release Notes
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

• If some series don't appear on the IRS archive

Solution: Select another patient and then reselect the previous patient series.
• When reconstruction is stuck and does not proceed (for CIRS only) follow the following steps:
a. Shut down the CIRS computer and wait approximately one minute
b. Turn on the CIRS computer and wait until the “IRS disconnected” message disappears.
c. Reconstruct off-line the problematic Raw data by redefining as Start position the original start position plus at
least 2 mm.
For example: if the original start position is 123.4 mm and the original increment is -0.5 mm then the new start
position will be 121 mm.
• On IRS systems, as in the previous software versions, the Raw Data on the IRS cannot be locked against
automatic delete when it is the oldest raw on the disk and a new scan is requested.
Solution: To reconstruct a study again, perform the reconstruction before the Raw Data is automatically deleted
from the IRS."

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 147
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Application Release Notes
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Brilliance (water-cooled) Version 2.2.1 and Mx8000 IDT V4.2.1

Application Release Notes

New Features in Brilliance 2.2.1

Cardiac
• New filters: Eight cardiac filters are available.
• CA and XresA are intended for large size patients
• CB and XresB are intended for Average size patients
• CC and XresC improves image quality for average size patients to get sharper images
• CD and XresD are intended for stent imaging
• The Xres filters use a special adaptive algorithm for noise optimization.
The user should select the best filter adequate for his needs. All 8 filters were present in the first and second betas of
BR2.2.1, however special attention should be given to image quality with filters CC and the Xres filters.
• Cosmix filter: Four new filters are introduced in BR2.2.1. The purpose of the COSMIX filters is to reduce the noise
in the vessels while preserving their edges thus enhancing the coronaries visualization in cardiac applications.
Validation of these filters will be done both internally and externally (Not in beta 1)
• Burlap artifact: A correction to reduce the burlap artifact on cardiac images is introduced to BR2.2.1. The
validation of this artifact will be done mostly internally.
• Continue cardiac scan: If scan continued, one ECG file and one volume scan is resulted when reviewing the data
in CT viewer or Cardiac viewer. Not applied to off line.
• Irregularities detection and correction: An automatic algorithm to detect irregularities in the patient heart rate
runs in the background of a cardiac scan. In case such an irregularity is detected, the following occurs:
• If the Cardiac Dose Right was ON, it will be cancelled automatically to allow reconstruction of additional phases
at higher image quality. The user receives the following message: “Cardiac Dose Right cancelled due to unstable
heart rate”.
• The ECG viewer notifies the user the number of irregularities detected
• The ECG wave presents the first irregularity detected.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 148
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Application Release Notes
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

• The irregularities detected are automatically labeled with a question mark. The user can accept or reject the
automatic detection with the left-click options. Before Accepting / Rejecting a detected irregularity, the user
should review the ECG wave and determine if the detected irregularity is actually an irregularity.
• If the user accepts the irregularity the question mark will disappear and in some cases additional phases will be
automatically added to the reconstruction request.
• If the user rejects the irregularity: the label will be removed and no changes in the reconstruction procedure will
be made.
• If the user takes no action (neither accepts nor rejects the irregularity): the question mark label remains and no
changes in the reconstruction is made.
• In offline reconstruction or in re-recon the user has three possibilities:

• Re-run the irregularities detection algorithm: right-click on the ECG viewer

and click Run Irreg autodetect
• Accept or Reject irregularities

• Click Reset

• Recon parameters (such as FOV and Shifts) are saved after evolving.

New Filters (applicable only for system with CIRS)

Six new filters with improved spatial resolution (both in plane and longitude direction) are introduced, two for each scan
mode: YA and YB for Standard Resolution, YC and YD for High Resolution and YE and YF for Ultra High Resolution.

mA and mAs Values

The mA values now appears together with the mAs value; this allows the user to know what tube power was used for a
given scan. In order to enable the display of both mA and mAs values:
1. Click Preferences in the Archive toolbox.
2. Select Image Viewing > Titles in the Preferences tree on the left side of the window.
3. Select (check) the Current checkbox.
4. Select the location on the image to view the mA value.
5. Click OK to close the Preferences window.
4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 149
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Application Release Notes
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Bolus Pro Automatic ROI Graphic Improvement

• Operator adjustment of the automatic ROI is limited to less than 1.5 around the original position to avoid inaccurate
positioning.
• Active ROI (the one that will trigger) is more prominent.

A New Surview Mode

A new Surview mode is introduced called Multi Surview. In this mode a large number of Surview scans may be
performed within the same study. This enables rescanning after a scanner operation errors or when a repetitive
procedure for Oncology purposes is needed.
In order to enable this new mode open the Preferences > Scan Options and select Multi Surview in the Surview
Mode drop-down list.

Force Max FOV in Detailed and UH Resolutions

Max FOV on the plan viewer includes shift calculations.

New GUI in Plan VIEWER

Max FOV is Displayed on the image. Data for off-line planning: the user will know that he cannot use data beyond the
max FOV.

Minimum Delay in Timed Scan

A new parameter was added to the scan protocol, in the Injection tab: Minimum delay. This parameter keeps the scans
with the minimum possible delay.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 150
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Application Release Notes
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Scanner Operation Cautions and Warnings

!
CAUTION

• During Bolus tracking, pay attention to the CT values on images.

• To start the clinical scan manually, click the button “Start Clinical scan”.
• When using the SAS injector – start the injection only after the message “Start Injection”
appears on the scanner screen.
• Perform daily and monthly scanner checks to ensure correct CT numerical values.
• Keep the Mylar clean at all times. Any contrast material left on the mylar surface, patient
table, and accessories will create image artifacts. (see instructions in the section Cleaning the
System).
• When Automatic dose-right ACS is used – always review the mAs value before scanning.
• When a Decubitus position is used, review the Surview scan angle: use 90° for AP and PA and
180° for Lateral.
• While connecting the patient to different Pulmonary detection devices, check that the cables
do not endanger CT personnel working in the Gantry room.
• While working in the scanner room, be aware of cables that may be lying on the floor in the
gantry room.
• Pulmonary bellows may cause allergic reaction; do not allow direct contact with the patient’s
body.
• A doctor must sign reports used for Interventional operations.

!
WARNING Biopsy CCT

• Ask the assistant to operate the panel.

• Perform operations on the console only according to the biopsy operator’s
instructions.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 151
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Application Release Notes
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Open Issues
• If images don't arrive to archive after log out then restart the host computer.
• Do not save images from the CT/MR application. The Bed position may be wrong.
• If at any point, an error message titled "Unhandled exception" pops-up: click Quit and log off before performing the
next scan.
• Do not use Print Screen. Use SnagIt to take screen captures.

General
• After installation, make sure that there all protocols are correct.
• It is highly recommended not to have more than 400 studies in the Local device Archive.
• When logged on as CT it is not possible to use the Long Tube Conditioning application.
• After restarting the host, Windows may launch with the wrong resolution (640X480), and without dual monitor
horizontal span support (both monitors will have the same display). In this case, restart the system again.
• If you move the bed manually by using the tapeswitch (either footswitch or couchswitch) while the system is
initializing or ready for a scan, the system will return to plan scan and numerous error message will appear. Close
the messages and continue routine work.
• Do not use a pitch higher than 0.6 in UHR scans. To avoid errors, always use appropriate Scan Type when
scanning with UHR mode.

Scanning
• After pressing Pause during Repeat Scan, clicking Next Series will perform the cancelled scan (repeat or
continue).
• When pressing pause on the CT-box, the Examination Flow dialog box is displayed. If Continue is then pressed,
the continued scan may start a couple of slices prior to the last one, meaning that some slices may be overlapped
and have the same image number.
• If the End Study is clicked before the reconstruction ends, the Surview ES image will not be saved.
• If the Start Study button does not respond, try clicking Home and then click Start Study again. If the problem
persists, wait 1 minute and try again.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 152
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Application Release Notes
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Plan on Surview
Do not plan Autolaunch to a review/analysis application in more than one step. Bear in mind that planning MPRs is an
Autolaunch by itself.

Archive
• To see new studies in the local archive, click Refresh in the Directory window.
• Filtering the series list: when typing a partial string, use "*" before and/or after the string. For example: searching for
patient named Smith, type the partial string Sm*.
• When copying data to the EOD, select 1-4 studies a time. Copying large batches of data may cause the system to
slow down.
• Avoid using the Full Rebuild option in the Archive.
• It is recommended not to delete more than 25 studies at once.
• Do not use the Split Series feature in Sub-selection.
• If series' appear to be missing in the IRS device, switch to a different study and then back to the current one.

Bolus Tracking
• If Go is disabled, check that the tracker post threshold delay is legal.
• Do not use minimum cycle time when rotation time=1.

Interventional CCT
• CCT fluoro - The last few images may not appear in the CCT viewer when releasing the pedal. These slices will
arrive after pause.
• Pressing the Pedal while scanner is initializing may interrupt the initialization process. Press the pedal only when
"Press Pedal" message appears.
NOTE If the table height and tilt are changed during the scan, image parameters will not be updated.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 153
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Application Release Notes
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Pulmo
• Do not use Pulmo scans in combination with Bolus tracking, timed scans or cardiac scans.
• Start offline recon only after the Pulmo study is completed and closed.
• The Pulmonary viewer in the operator console may not be accurate and used for the reconstruction process only.

Cardiac
• Generate a Cardiac protocol only from a factory Cardiac-protocol.
• Do not scan patients with a heart rate lower than 40 or higher than 140.
• Y Scale of HR graph does not adjust automatically. This results in the graph running out of the visible area.
• ECG R-tag Correction: Do not use APB/VPB correction
• ECG Editing tool: Do not use "Add new R-Tag" option.
• Do not use the following options during a cardiac study:
• Tilt
• DOM (in Retrospective Cardiac scan)
• Auto Processing
• Cardiac Injection Guide
• Do not delete ECG from the archive.
• It is highly recommended to use 0.2 pitch for all heart rates.
• Automatic arrhythmia detection is applied before and after each scan. Currently, correction of arrhythmia can only
be performed manually via R-tag editing.
• Do not use off-line reconstruction from the Cardiac Viewer (Re-Recon)— perform additional reconstructions in the
Off-Line Recon application only.
• When Cardiac Doseright is applied, automatic arrhythmia detection will automatically cancel this feature if an
irregular rhythm is detected during a scan.
• Reset monitor between scans.
• Prospective gating for calcium scoring should be performed at phase 75% (and not 85%). Prospective and
retrospective phase definitions are now equivalent.
• Do not perform a non-cardiac scan after a cardiac one in a single study.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 154
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Application Release Notes
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

• Do not use the following filters: 'D', 'CD', and 'XCD'.

Cardiac Off-line Reconstruction

The reconstruction shift and zoom settings are not saved with the Raw Data in Cardiac Scans. Therefore, if off-line
reconstructions are needed (e.g. for different phases) proceed as follows:
1. Load the original series in the CT Viewer and select the 2D scene.
2. Make a note of the x and y shift and the zoom settings of the images.
3. Load the Raw Data from the IRS.
4. Change the shift and zoom values from the original images as shown in Step 2 on page 155 and then start the off-
line reconstruction.

Preferences
• The Fast get ready feature is not available. Make sure it set to NO.
• When activating/deactivating the Fast get ready feature, changes will only be applied after logout/login.
No message will appear.

TLCT
The actual cycle time can differ from the planned cycle time by up to 0.5 seconds.

Viewing and Filming

• When sending images from CT Viewer or from Cardiac viewer to film, the contrast sign (C) will not appear on the
filmed image. The ECG value in cardiac images will also be missing.
• Before using Generate Protocols or Air Calibration, click Start Study/End study and make sure the patient data
fields are empty.
• Avoid printing while images are being loaded to the Master Film.
• When using Auto Filming, always make sure all requested images were loaded to Master Film with correct
windowing settings.
• Dental CT Application: only images with matrix 512x512 can be loaded to the application. Use only Spiral protocols
with SP reconstruction.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 155
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Application Release Notes
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

• Stereotaxis: use only Spiral protocols with SP reconstruction or Axial protocols. If axial protocols are used, select
only 16x0.75 and thickness 3mm or 16x1.5 and thickness 6mm.
• Cursor coordinates value on surview may not be accurate, do not use them to measure the positioning.
• Do not use the CT / MR application.

Common IRS (CIRS) Guidelines

• Evolving reconstruction might be slow. You will see the green line advancing and images still arriving even when the
scan is completed.
• The toolbox state messages might not be synchronized (messages such as: Scanning, Reconstruction, Acquisition
complete).

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 156
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Service Release Notes
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Appendix B: Service Release Notes

The current version includes the following features relative to the software versions 1.2.5/3.2.5:
• New logon user name and password for service and administrator:
• Logon for service is philips_service.
• Service logon no longer opens scanner application automatically. To launch scanner application click Scanner
Application icon on Host desktop.
• New 108 character Option License Key
• K2D Visa Service License Key
• UPS functionality changes:
• Uninterruptible Power Supply (UPS) will supply power to the console for approximately 10 to 15 minutes when
there is a power failure. To improve system security against program viruses, the UPS does not send messages
(time left on UPS power or shut down) to the user. The user must quickly complete the reconstruction for the last
scan and then safely shut down the Host and IRS computers.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 157
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Service Release Notes
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Set User Mode Workaround

Problem:
After using the Set User Mode utility to change the user
mode, the service preferences reserved for Service mode
remain enabled in the CT mode.
Workaround:
1. Complete all necessary work that requires Service
mode.
2. Open the Set User Mode utility and select the new
user mode Technologist.
3. The Password dialog box opens. Type mxtech.
4. Click Close.
The service tools return to CT mode.

Figure 121:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 158
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Service Release Notes
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Synchronizing CANpro with Host Computer

Turing Off the Firewall to synchronize CANpro with the Host computer.

NOTE If the Laptop with the CANpro is connected

to the Host through the Hospital network,
switch to a direct connection via a crossover
cable to the Host directly during the
Synchronization procedure.
1. Disconnect the Host computer from the Hospital
network in order to prevent a software virus intrusion.
2. Press the Windows key and click Settings >
Control Panel.
3. Double-click Windows Firewall.

Figure 122:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 159
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Service Release Notes
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

4. Select Off (not recommended) and

click OK
5. Start the Canpro program.
6. After the Canpro program opens the
file (Synchronizing done), repeat steps
1 and 2 and select "On
(recommended) and click "OK".
7. Re-connect the Host computer to the
Hospital network.
NOTE If the Laptop was connected to
the Hospital network you may
now reconnect to the Hospital
network.

Figure 123:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 160
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 IBox Software Upgrade
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Appendix C: IBox Software Upgrade

NOTE If your system does not have an IBox skip to Remote Recon Option Upgrade on page 83.
If you do have an IBox verify that the USB cable between IBox and Host is connected and the IBox is ON (Gantry
ON) before proceeding.

IBox Driver Verification

Ver if y that the IBox dr iver is installed properly as follows:

1. If needed press Windows +D key to view the

desktop.
2. On the desktop right-click My Computer and
select Properties.
3. Select System and in the Hardware tab, click
Device Manager. The Device Manager
window opens (see Figure 124 on
page 161).
4. Click the + next to the Universal Serial Bus
controllers to view all the installed drivers;
the Philips Medical IBox Device should
appear in the list.
5. Close all the windows.

Figure 124: Computer Management Window

6. If the driver is not installed continue with the section Installing the IBox Driver on page 162.
If the driver is installed:
- If your system was V1.2.5./3.2.5 than skip to Programming IBox FPGA Upgrade from V1.2.5/V3.2.5 on page 163.
- If your system was V2.0.2/4.0.2 than skip to IBox Flash Upgrade on page 174.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 161
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 IBox Software Upgrade
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Installing the IBox Driver

1. Reboot the Host computer.
2. After boot-up, the Found New Hardware Wizard opens (see Figure 125 on page 162) to direct you in IBox
installation.

Figure 125: Hardware Wizard Figure 126: Driver Selection Dialog Box

3. Select the Install the Software Automatically option and click Next.
4. In the next dialog box, select the first option; c:\drivers\[Link] Figure 126 on page 162 and click Next.
5. The driver is automatically installed. Click Finish to close the Wizard.
6. For an upgrade from V2.02/V4.02 skip to IBox Flash Upgrade on page 174, otherwise continue to Programming
IBox FPGA Upgrade from V1.2.5/V3.2.5 on page 163.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 162
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 IBox Software Upgrade
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Programming IBox FPGA Upgrade from V1.2.5/V3.2.5

NOTE Before performing this procedure when upgrading from V1.2.5/3.2.5 first verify the FPGA version is not already
V1.5. Follow the procedure in section IBox Software and FPGA Version Verification on page 176
If your FPGA version is 1.5 continue to IBox Flash Upgrade on page 174.

Installing the FPGA Files to the Laptop

1. Insert the IDT/BRHost V4.2.1.1925/2.2.1.1925 CD into the Laptop CD drive.
2. Right-click Start and select Explorer.
3. Create a folder C:\usr\[Link]\IBoxFPGA\.
4. Navigate to folder IboxFPGA_IDT\1.0.10\ on the CD device.
5. Copy the two files in the folder to the new folder C:\usr\[Link]\IBoxFPGA\.
6. Eject the IDT/BRHost V4.2.1.1925/2.2.1.1925 CD.

FPGA File Programming

1. Remove the Gantry left column upper and lower covers.
2. On the CT Box, turn the power switch OFF.
3. Locate the P2 JTAG connector on the IBox (see Figure 128 on page 165).

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 163
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 IBox Software Upgrade
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

!
CAUTION Follow all guidelines for ESD Anti-static protection before performing any service procedure.

4. Connect the JTAG plug with the leads to the

JTAG adaptor as shown in Figure 127 on
page 164.
NOTE If JTAG LED colors do not match those
displayed in Figure 127 on page 164,
match up the JTAG adapter leads to
the board connector by pin names.

JTAG Adapter Plug with Leads

Figure 127 JTAG Adapter and Plug

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 164
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 IBox Software Upgrade
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

5. Connect the JTAG cable leads to P2 according to Table 24 on page 165.

P2-JTAG connector 1 2

9 10
Figure 128: P2 IBox Connector

Table 24: JTAG Connections

P2 Connector Pin Number Pin Name JTAG Lead

1 TDI/DIN Green Lead

2 VCC Red Lead

3 TMS/PROG Yellow Lead

5 TCK/CCLK Blue Lead

7 TDO/D/P Purple Lead

10 GND Black Lead

6. Switch ON the power to the Gantry by turning the CT Box power switch ON.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 165
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 IBox Software Upgrade
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

IBox Programming Procedure

1. Press the Reset button shown in Figure 129 twice! in order to load a
default firmware before loading the updated firmware.
2. Launch the Xilinx JTAG programmer software.
3. With version Xilinx 7.1i software, a Project Selection box will be
displayed. Click the Cancel button.

Figure 129:
4. The Operation Mode Selection dialog box shown in Figure 130
opens. Click Cancel.
5. The iMPACT Configuration Mode window should be displayed.
6. If you are using a USB JTAG cable, set the communication speed to
750 KHz as follows:
a. Click on Output from the top Menu bar (or right-click in the white
window area).
b. Choose Cable Setup from the drop-down menu. The Cable
Communication Setup Menu should be displayed.
c. Select Platform Cable USB, Select Speed, Local Cable Location,
and the USB port being used on your laptop.
d. Click the OK button.
e. In the TCK Speed/Baud Rate select 750 KHz.
f. Click the OK button.
Figure 130: Operation Mode Selection

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 166
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 IBox Software Upgrade
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

7. Right click in the iMPACT window

and choose Initialize Chain or click
on the Initialize Chain button on the
toolbar shown in Figure 131 on
page 167.

Figure 131: Initialize Chain Button

8. When the message 3 Devices

Detected shown in Figure 132
appears.
9. Click OK.

Figure 132: Boundary-Scan Chain Summary

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 167
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 IBox Software Upgrade
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

10. When the Assign New

Configuration File dialog box shown
in Figure 133 on page 168 appears
click Cancel All.

Figure 133: Assign New Configuration File Dialog Box

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 168
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 IBox Software Upgrade
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

11. The window opens showing the IBox

Prom chain (Figure 134).

Figure 134: IBox Chain

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 169
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 IBox Software Upgrade
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

12. Define the chain and load the files for programming as
follows:
a. Double click on the device #1 icon from the
beginning of the chain as shown in Figure 134 on
page 169. The selected device number appears in
the lower window (in blue) of the iMPACT.
b. The Assign New Configuration File window shown
in Figure 135 on page 170 opens.
c. Navigate to the C:\usr\[Link]\IBoxFPGA
folder and select the appropriate firmware file for the
first device in the chain (refer to the table below for
the correct firmware versions). Click Open.
d. Repeat the procedure for the third device in the
chain.
NOTE Figure 135 on page 170 is for example only.
Data may differ.
Figure 135: Assign New Configuration Program for
Programming

IBox

Device # on chain File Name SW FPGA

1 I_BOX_Ver1_5.mcs 2.33 1.5

2 Not for programming

3 [Link]

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 170
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 IBox Software Upgrade
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

13. Verify the chain is defined correctly by

comparing the file names under each
device as shown in Figure 136 and the
appropriate file names.
14. Click on the Device #1 icon and then
press and hold the Ctrl-key and click
on the Device #3 to select the devices
for programming as shown in
Figure 136. They will become green.
15. Verify that in the lower window a
message appears stating that the
devices #1 and #3 have been selected
as shown in Figure 136.
NOTE Figure 136 is for example only. Example Only, Data may Differ
Data may differ.

Selected device

Figure 136: Chain Selection For Programming

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 171
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 IBox Software Upgrade
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

16. From the Operations menu, click Program as shown in Figure 137 on page 172; the Program Options window
opens.
17. Select the Erase Before Programming and Verify check boxes as shown in Figure 138 on page 172 and then
click OK.

Figure 137: Program Menu

Figure 138: Program Option Window

NOTE The Programming Succeeded and Verify Succeeded messages disappear after 10 seconds.
18. The Operation Status window opens. Wait for “Programming Succeeded”
message to appear. You can see the status of the programming in the
window below. The programming takes approximately 1 minute.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 172
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 IBox Software Upgrade
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Final Steps
1. Select Files from the main menu and click Exit and then click No to exit the IMPACT application.
2. On the CT Box, turn the power switch OFF.
3. Remove the Xilinx JTAG Programming cable.
4. Mount the Gantry left column lower and upper covers.
5. On the CT Box, turn the power switch ON.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 173
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 IBox Software Upgrade
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

IBox Flash Upgrade

1. If needed log on as philips_service.

2. On the Desktop, double-click the
IBox Diag icon. The IBox Diagnostic
window opens (see Figure 139 on
page 174).
NOTE The IBox diagnostic wizard dialog
can be minimized on the Windows
Taskbar.
select the IBox Diagnostics.
3. Select IBox program upgrade (Flash
Programming).
4. Click Next to load the program in the
IBox flash memory; the Backup Current
Program window opens.

!
CAUTION It is very important that
you ONLY click Skip and
do nothing else in the
Backup Current Program
window.
Figure 139: Welcome to IBox Diagnostics - Program Upgrade
5. Click Skip.
6. In the next dialog, click Browse and navigate to c:\usr\[Link]\IBoxDiag\PromVersion\IBox_v_2.[Link]
(Figure 140 on page 175).
7. Click Open and then click Next. The flash programming starts.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 174
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 IBox Software Upgrade
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

NOTE If a failure message appears when performing the following step, repeat the IBox Flash Upgrade on page 174
procedure again. Try several times before reporting a hardware failure.
8. If an error message appears, click Exit to close the IBox Diagnostic application.
Restart the Host, log on as philips_service, and start the procedure from Step 2 on page 174.
9. After successful flash programming, the following message appears as shown in Figure 141 on page 175
“Flash burn terminated successfully. IBox reset is needed. Do You want to reset the IBox?”
Click Yes.

Burn-in progress may still appear underneath

“success” message.

Figure 140: Path for Flash Programming Figure 141: Flash Programming Success
10. Click Next and then click Exit to close the IBox Diagnostic wizard.
11. Verify the correct IBox and FPGA software versions as described in IBox Software and FPGA Version Verification
on page 176.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 175
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 IBox Software Upgrade
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

IBox Software and FPGA Version Verification

Perform the IBox software and FPGA Versions verification as follows:
1. On the Desktop, double-click the IBox Diag icon; the Welcome to IBox Diagnostic window opens.
2. Select the Manual Test option box and then click Next; the IBox Diagnostic Wizard shown in Figure 142 on
page 176 opens.
3. From the IBox Diagnostic Wizard, click Get Version as shown in Figure 143 on page 176.

Figure 142: Welcome to IBox Diagnostics Window Figure 143: Manual Test

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 176
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 IBox Software Upgrade
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

The IBox version and FPGA version appears in the Test in Progress window (see example in Figure 144 on
page 177).

Figure 144: Test in Progress Window

NOTE If the FPGA version is not 1.5 perform the procedure Programming IBox FPGA Upgrade from V1.2.5/V3.2.5 on
page 163 before continuing.
If the IBox version is not 2.33 perform the procedure IBox Flash Upgrade on page 174.
4. Click OK to close the Test in Progress window. Then click Exit to close the IBox application.
5. Continue with Remote Recon Option Upgrade on page 83.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 177
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Setting the Boot Devices
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Appendix D: Setting the Boot Devices

The following procedure enables the setting of boot devices during restart. Verify that the devices are set in BIOS in the
order that appears below. If it is not in that order, change it to the order of the procedure below.
1. Restart the computer.
2. When the Intel screen appears with a message saying F2-setup in the bottom left-hand corner, press F2 and wait
for the BIOS setup screen to appear.
3. Use the keyboard arrow keys to highlight the Boot menu. Press Enter.
4. A menu appears. Highlight the CD-ROM Drive. Use the keyboard ‘+’ and ‘-‘ keys and move the CD-ROM Drive to
the top of the list. The list should appear as follows:
• CD-ROM Drive
• Removable Devices
• Hard Drive
5. Highlight the Hard Drive and press Enter.
6. A sub-menu appears. The list should appear as follows:
• ST340016A- (PM)
• Bootable Add-in Cards
• PCI RAID Adapter (bus 03 dev 00)
In case the order is different, use the ‘+’ and ‘-‘ keys to change the devices’ order.
7. Use the keyboard arrow keys to highlight the exit button. Click Enter and save changes.
8. Press F10 to Save and Exit. The computer will restart.
9. Continue with Step 2 on page 93.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 178
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Change Host-IRS Connections Settings
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Appendix E: Change Host-IRS Connections Settings

1. On the Host PC desktop, double-click the Olevel Interface icon to launch the O-Level Diagnostics Panel.
2. On the O-Level Diagnostics Panel, click the Adjust Hospital-Recon Network button.
3. The pop-up will ask if you want to change the subnet to [Link].
4. Click OK on the pop-up.
5. On the O-Level Diagnostics panel, click the Exit button.
6. For a Vertical Server skip to Step 2 on page 180

Configure Remote Desktop Connections

1. On the Host PC Desktop, open CIRS folder.
If the folder does not exist, from the desktop right-
click the Recon-S1 icon, select Edit from the menu
and skip to Step 3 on page 179.
2. Right-click on the recon-S1 icon, and select Edit
form the menu.
3. On the Remote Desktop Connection dialog, in the
Computer field change 192 to 10.
4. Click Save As... (the Save As dialog should default
to the CIRS folder. If it does not, then browse to the
CIRS folder. If the CIRS folder does not exist, save it
to the desktop.).
5. On the Save As dialog, select recon-S1 and click
Save. Then click Yes at the prompt.
6. Click Cancel to close out the Dialog.
7. Right-click on the recon-S2 icon, and select Edit
form the menu.
8. On the Remote Desktop Connection dialog, in the
Computer field change 192 to 10.
Figure 145:

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 179
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Change Host-IRS Connections Settings
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

9. Click Save As... (the Save As dialog should default to the CIRS folder. If it does not, then browse to the CIRS folder.
If the CIRS folder does not exist, save it to the desktop.).
10. On the Save As dialog, select recon-S2 and click Save. Then click Yes at the prompt.
11. Click Cancel to close the dialog box.

Enable Supervisor service on S1

1. Log on to the S1 server from the Host:
a. If you created a Recon S-1 Remote Desktop shortcut on the Desktop in Step 3 on page 110, double-click it. If
not, open the CIRS folder and double-click the Recon S-1 Remote Desktop shortcut there.
b. Click OK at the security warning.
c. At the Log on prompt, enter “philips_service”. In the Password field, enter the appropriate password.
d. Click OK.
2. Enable Supervisor service on S1:
NOTE On a Vertical Server use the KVM instead of Remote Desktop to connect to the server.
a. On the Desktop, double-click the Services icon.
b. Right-click on CIRS Supervisor Service, and select Restart.
c. Click Apply, then click OK.
d. Close the Services window.
e. Close the Remote Desktop connection to S1.
NOTE For two server configuration continue with Step 13 on page 115.

For one server configuration continue with Step 13 on page 122.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 180
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Change HOST - CIRS IP Addresses
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Appendix F: Change HOST - CIRS IP Addresses

Hospital LAN uses same IP addresses

In the event that the hospital's LAN uses the [Link] IP addresses, you can use [Link]. You must then
change all occurrences of 192 to 10. Keep the remaining values the same.
There are four parts:
NOTE In order to change the IP address disconnect the Host from the Hospital network and perform the following
procedures on S1 and S2 (if it exists).

If you encounter problems with the Remote Desktop connection to the CIRS servers, use a keyboard, mouse,
and monitor connected directly to each CIRS server when performing the procedure in Change IP Addresses on
the CIRS Servers on page 181.

Change IP Addresses on the CIRS Servers

NOTE On a Vertical Server use the KVM instead of Remote Desktop to connect to the server.
1. Log on to the S1 server from the Host:
a. If you created a Recon S-1 Remote Desktop shortcut on the Desktop in Step 3 on page 110, double-click it. If
not, open the CIRS folder and double-click the Recon S-1 Remote Desktop shortcut there.
b. Click OK at the security warning.
c. At the Log on prompt, enter “philips_service”. In the Password field, enter the appropriate password.
d. Click OK.
2. On the S1 desktop, double-click the Recon icon.
3. In the Command window, type: Supervisor -sethost [Link]
4. Press the <Enter> key.
5. On the S1 server:
a. Navigate to C:\windows\system32\drivers\etc.
b. Backup the Host files.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 181
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Change HOST - CIRS IP Addresses
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

c. Right-click on Hosts, and select Properties from the menu.

d. Click on Read-only to un-select it.
e. Click Apply, then click OK.
f. Right-click on Hosts, and select Open. On the Open With dialog, select Notepad and click OK.
g. In the file, change all occurrences of 192 to 10.
h. When finished, click File > Save. Then click File > Exit.
i. Right-click on Hosts, and select Properties from the menu.
j. Click on Read-only to select it.
k. Click Apply, then click OK.
l. Close the Folder window.
[Link] to C:\Program Files\Philips\CIRS
n. Right-click on the file [Link], and select Edit from the menu.
o. In the file, change all occurrences of 192 to 10.
p. When finished, click File > Save. Then click File > Exit.
6. On the S1 desktop:
a. Double-click the Set IP Address icon.
b. Click Yes in the CIRS Set IP Address window when prompted.
c. On the Configure IP Address dialog, enter [Link], then click OK. The application will now set both IP
addresses.
d. The Command Window will show the progress, and then close when complete.
e. Close the Remote Desktop Connection to S1.
f. Click OK in the Disconnect Windows Session.
NOTE On installations with only one server (Vertical Server), skip to CIRS Server Changes Final Steps on page 184.
7. Log on to the S2 server from the Host:
a. If you created a Recon S-2 Remote Desktop shortcut on the Desktop in Step 3 on page 104, double-click it. If
not, open the CIRS folder and double-click the Recon S-2 Remote Desktop shortcut there.
b. Click OK at the security warning.
c. At the Log on prompt, enter “philips_service”. In the Password field, enter the appropriate password.
4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 182
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Change HOST - CIRS IP Addresses
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

d. Click OK.
8. On the S2 server:
a. Navigate to C:\windows\system32\drivers\etc.
b. Backup the Host files.
c. Right-click on Hosts, and select Properties from the menu.
d. Click on Read-only to un-select it.
e. Click Apply, then click OK.
f. Right-click on Hosts, and select Open. On the Open With dialog, select Notepad and click OK.
g. In the file, change all occurrences of 192 to 10.
h. When finished, click File > Save. Then click File > Exit.
i. Right-click on Hosts, and select Properties from the menu.
j. Click on Read-only to select it.
k. Click Apply, then click OK.
l. Navigate to C:\Program Files\Philips\CIRS
[Link]-click on the file [Link], and select Edit from the menu.
n. In the file, change all occurrences of 192 to 10.
o. When finished, click File > Save. Then click File > Exit.
9. On the S2 desktop:
a. Double-click the Set IP Address icon.
b. Click Yes in the CIRS Set IP Address window when prompted.
c. On the Configure IP Address dialog, enter [Link], then click OK. The application will now set both IP
addresses.
d. The Command Window will show the progress, and then close when complete.
e. Close the Remote Desktop Connection to S2.
f. Continue with CIRS Server Changes Final Steps on page 184.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 183
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Change HOST - CIRS IP Addresses
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

CIRS Server Changes Final Steps

1. Shutdown the Host computer.
NOTE For a Vertical Server, click Start > Shutdown > Shutdown and click OK to confirm, then skip to Step 3 on page
184.

2. Power OFF both CIRS servers.

a. Double-click the Remote Desktop icon Recon S-2.
b. Right-click on the Windows Taskbar, and select Task
Manager.
c. In the Task Manager window, click Shut Down > Turn Off as
shown in Figure 146 on page 184.
d. Click Yes on any messages that appear.
e. Click OK on the Remote Desktop Disconnected prompt.
f. Double-click the Remote Desktop icon Recon S-1 and repeat
for the S1 CIRS server. Figure 146: Task Manager Shut Down Menu

NOTE During shutdown, the Remote Desktop connection will automatically disconnect and return you to the Host
desktop.
3. Power on the server(s) by depressing and holding the switch on the front of the server until the green light to the left
of the switch illuminates.
4. Power On the Host computer.
5. Log on as philips_service.
6. Continue to Change Host-IRS Connections Settings on page 179.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 184
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Updating the Acquisition Device Driver
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Appendix G: Updating the Acquisition Device Driver

NOTE On a Vertical Server use the KVM to connect to S1 instead of using the Remote Desktop connection.
1. Using Windows Remote Desktop, connect to S1:
a. If you created a Recon S-1 Remote Desktop shortcut on the Desktop in Step 3 on page 110, double-click it. If
not, open the CIRS folder and double-click the Recon S-1 Remote Desktop shortcut there.
b. Click OK at the security warning.
c. At the Log on prompt, log on as philips_service.
d. Click OK.
2. Click Start, then right-click on My Computer.
3. Select Manage.
4. Click Device manager.
5. Updating the ACQ board
a. Click the [+] on Philips acquisition devices.
b. Look for the Philips ACQ board
c. Right-click Philips ACQ board.
6. Select Update driver… (the first option in the list); the Update Driver Wizard appears.
7. In the Update Driver Wizard, select “No, not this time” and then click Next.
8. Select “Install from a list or specific location (Advanced)”. Click Next.
9. Select “Don't search. I will choose the driver to install”.
10. Click Next.
11. Click Have Disk…
12. Navigate to C:\Program Files\Philips\CIRS\drivers.
13. To update the ACQ driver, select the [Link] file and click Open.
14. Click OK.
15. Click Next.
16. Click Finish.
17. Close the Computer Management window.
4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 185
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Manually Updating Acquisitor FPGA Programming
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Appendix H: Manually Updating Acquisitor FPGA Programming

!
WARNING Do NOT power down or reboot the server, during the FPGA update. This could
cause the board to stop functioning.
1. On the Desktop, click the ACQ Diagnostics icon to start the CIRS Acquisition Board Diagnostics application.
2. Click JTAG Download, to launch the JTAG Download window.
3. On the JTAG Download window, click Select File.
4. Navigate to the C:\ProgramFiles\Philips\CIRS\AcqGem folder, and right-click the “ACQ16V_V10.svf” file.
5. Click Open.
6. In the JTAG Download window, click OK.
NOTE If the FPGA version is already up-to-date:
• A dialog box will indicate that the update will not be done.
• Click OK and on the CIRS Acquisition Board Diagnostics window.
• Click Quit. You have completed updating the Acquisition software.
7. After the download is complete, a dialog box appears with the message: “JTAG Download of the file was
successful. Shutdown and power up the PC to reconfigure the FPGA”. Click OK.
8. On the CIRS Acquisition Board Diagnostics window, click Quit.
NOTE The downloaded FPGA will not take effect until the power to the board is cycled.
NOTE For a Vertical Server, click Start > Shutdown > Shutdown and click OK to confirm, then skip to Step 13 on page
187.
9. Right-click the Windows Taskbar, and select Task Manager.
10. In the Task Manager, click Shut Down as shown in Figure 146 on page 184.
11. Click Yes on any messages that appear.
12. Press Enter.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 186
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Manually Updating Acquisitor FPGA Programming
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

NOTE During shutdown, the Remote Desktop connection will automatically terminate and return you to the Host
desktop.
13. Power on the server by pressing and holding the switch on the front of the server until the green light to the left of
the switch illuminates.
NOTE For two server configuration continue with Step 4 on page 113.
For one server configuration (vertical server) continue with Step 12 on page 122.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 187
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Manually Updating Acquisitor FPGA Programming
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Manually Updating the 3DBP Device Driver

NOTE On a Vertical Server use the KVM to connect to S1 instead of using Remote Desktop to connect to S2.
1. Using Windows Remote Desktop, connect to S2:
a. If you created a Recon S-2 Remote Desktop shortcut on the Desktop in Step 3 on page 104, double-click it. If
not, open the CIRS folder and double-click the Recon S-2 Remote Desktop shortcut there.
b. Click OK at the security warning.
c. At the Log on prompt, log on as philips_service.
d. Click OK.
2. Updating the 3DBP board
a. Click the [+] on Philips Backprojection devices.
b. Look for the 3DBP Backprojection board.
c. Right-click 3DBP Backprojection board.
3. Select Update driver… (the first option in the list); the Update Driver Wizard appears.
4. In the Update Driver Wizard, select “No, not this time” and then click Next.
5. Select “Install from a list or specific location (Advanced)”.
6. Click Next.
7. Select “Don't search. I will choose the driver to install”.
8. Click Next.
9. Click Have Disk…
10. Navigate to C:\Program Files\Philips\CIRS\drivers.
11. To update the 3DBP driver select the 3DBP file and click Open.
12. Click OK.
13. Click Next.
14. Click Finish.
15. Close the Computer Management window.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 188
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Manually Updating Acquisitor FPGA Programming
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Manually Updating 3DBP FPGA Programming

!
WARNING Do NOT power down or reboot the server, during the FPGA update. This could
cause the board to stop functioning.
1. Double-click the 3DBP Diagnostics icon to start the CIRS 3DBP Board Diagnostics application.
2. Click JTAG Download, to launch the JTAG Download window.
3. In the JTAG Download window, click Select File.
NOTE There are two different FPGA files, “3DBPLC_FPGA.svf ” for the 2 ASICs 3BP card in the Vertical Server and
“3DBP_FPGA.svf” for the 6 ASICs 3DBP card in other CIRS servers.

Figure 147: .svf File for the 2 ASICs 3BP card Figure 148: .svf File for the 6 ASICs 3BP card
4. Navigate to the C:\ProgramFiles\Philips\CIRS\3DBP folder, then select the file “3DBP_FPGA.svf” or
“3DBPLC_FPGA.svf” for a Vertical Server, and click Open.
5. In the JTAG Download window, click OK.
NOTE If the FPGA version is already up-to-date:
• A dialog box will indicate that the update will not be done.
• Click OK and on the CIRS Acquisition Board Diagnostics window.
• Click Quit. You have completed updating the Acquisition software.
6. In the BpDiagGUI window, click OK. This will appear after programming is complete.
7. In the CIRS 3DBP Board Diagnostics window, click Quit.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 189
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Manually Updating Acquisitor FPGA Programming
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

NOTE The downloaded FPGA will not take effect until the power to the board is cycled.
NOTE For a Vertical Server, click Start > Shutdown > Shutdown and click OK to confirm, then skip to Step 11 on page
190.
8. Right-click the Windows Taskbar, and select Task Manager.
9. In Task Manager, click Shut Down > Shut Down as shown in Figure 146 on page 184. Click Yes on any messages
that appear.
10. Press the Enter key.
NOTE During shutdown, the Remote Desktop connection will automatically terminate and return you to the Host
desktop.
11. Power on the server by pressing and holding the switch on the front of the server until the green light to the left of
the switch illuminates.
NOTE For two server configuration continue with Configure S1 on page 110.
For one server configuration continue with Step 11 on page 122.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 190
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Gantry Firmware Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Appendix I: Gantry Firmware Installation

Gantry Firmware Installation

1. Log on as philips_service.
2. Switch the Gantry ON.
3. On the Scan Control Box, press the emergency STOP button.
4. Click Home and from the Calibration menu, click Gantry and Couch Calibration.

5. From the Flash menu, select Load. The Flash

Load dialog box appears (see Figure 149).
6. Select the specific firmware controller.
7. Ensure that the Flash Load Firmware option
is selected, and click Select File. The Select
Controller dialog box appears (Figure 149).
8. Select the required Firmware Version from
the Available Firmware Versions list in
Table 26 on page 193, and click OK.
The Flash Load dialog box reappears
(Figure 149).
9. Click OK [Link] Flash Loading message
appears. Wait until Firmware loading is
complete.
Figure 149: Flash Load Dialog Box
10. In the next window click Yes.
11. Repeat Step 6 on page 191 to Step 10 on page 191 above for all of the remaining controllers as needed.
12. Select Exit from the File menu to close the Gantry and Couch Calibration window. Click OK.
13. Turn the Gantry OFF and then turn it ON.
14. Log off from the Host and then logon again as philips_service (password service_only).

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 191
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Gantry Firmware Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Check the Firmware Versions

Check the Firmware Versions as follows:
1. From Home > Calibration run
Gantry and Couch Cal.
2. From Simulation select Load >
List Fw Ver. E
0
3. From Simulation select Start. 0
4. From the list of frames, double 5
0
click on each of the fist line after
"## xxx FW ID". The CANpro
Telegram Interpretation dialog
box appears. For details see
Figure 150.

Figure 150: MCU E0050

5. Use Table 25 on page 192 and convert the numbers in the number lines to ASCII
(30 = 0, 35 = 5, etc.).
Table 25:

Hex
30 31 32 33 34 35 36 37 38 39
number

Value 0 1 2 3 4 5 6 7 8 9

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 192
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Gantry Firmware Installation
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

6. Verify the list in Table 26 is the same as the values in the CANpro Telegram Interpretation.
Table 26: Controller Firmware Versions

Controller Firmware Version

ACU VA00G

DOM VA00D

FOC VA00I

GPC VA00G

MCU E0050

PTH VA00E

PTV VA01G

RTC VA00H

XRS VA00E

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 193
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Enabling 0.42 Sec. Rotation Speed for Rotor Balancing
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Appendix J: Enabling 0.42 Sec. Rotation Speed for Rotor Balancing

1. Log on as philips_service.
2. In the upper left corner of
the application, click
Gantry Control (A). A

Figure 151: Upper Left Corner of the Application

3. Click Edit Table (B).
B

Figure 152: Gantry Control Window

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 194
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Enabling 0.42 Sec. Rotation Speed for Rotor Balancing
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

4. Click Update Table (C).

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 195
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Enabling 0.42 Sec. Rotation Speed for Rotor Balancing
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

5. Select tab (D).

6. Click OK (E).

Figure 153: Table Selection

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 196
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Enabling 0.42 Sec. Rotation Speed for Rotor Balancing
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

7. Find the last 2 rows that contain real data (0x00 in all fields of a row is not data) in, then enter the same data into the
next 2 rows (F).
Table 27: Example of Step 7

Before After

The last two rows

containing data
F
Enter the same
data into the
next two rows

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 197
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Enabling 0.42 Sec. Rotation Speed for Rotor Balancing
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

8. Edit the values (G) in the new lines according to Table 28

Table 28: New Values for Lines Added

1st field 2nd field 3rd field 4th field 5th field
1st line added no change 0x01 0xa4 no change no change
2nd line added no change no change no change no change no change

Table 29: Example of Step 8

Before After

G
Find fields 2 and 3 Change values to
of the 1st new line 0x01 and 0xa4

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 198
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Enabling 0.42 Sec. Rotation Speed for Rotor Balancing
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

9. Click Update (H).

Figure 154: Update Button in the Gantry Control Table

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 199
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Enabling 0.42 Sec. Rotation Speed for Rotor Balancing
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

10. Click Exit (I).

NOTE Running XRT Z
alignment erases
the values from the
table. Therefore
you must repeat
this procedure
immediately before
running Rotor
Balancing.

Figure 155: Update Button in the Gantry Control Table

11. In the Gantry Control

window, click Exit (J). J

Figure 156: Gantry Control Window

12. From the CT-Box, turn the Gantry Off and On again. This updates the Tab table.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 200
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.
 Enabling 0.42 Sec. Rotation Speed for Rotor Balancing
BrillianceTM CT 16/10/6-Slice Configuration (water) V.2.2.1 Mx8000 IDT 16/10-Slice Configuration V4.2.1 Upgrade Instructions Rev F

Restore Calibrations (Partial Restore)

1. Insert the backup EOD into the EOD drive.
2. Launch the Backup/Restore application: double-click Backup/Restore icon on the Desktop.
3. Select the Restore tab.
4. Click Browse and navigate to Drive F: (EOD), select the backup directory with the most recent date and click OK.
5. In the Restore tab, select only the Calib. Tables option.
6. Click Start Restore.
7. When the restore is complete a message appears, click OK.
8. Scroll up the log and look for errors in the Log window (the Restore Done message appears even if the restore was
not successful).
9. Click Close in the Log window.
10. Click Exit in the Backup/Restore window.
11. Eject the EOD.
12. Return to Step 3 of System Calibrations and Performance Verifications on page 126.

4550 191 01302 © 2011 Koninklijke Philips Electronics N.V All Rights Reserved CSIP Level 1 201
Attention: This page contains copyrighted materials that are confidential and/or proprietary. Any release or distribution of this material, without permission, is a violation of law.