Toll Free: 800­345­4364 | sales@aircompressorworks.

com

Search Catalog By Keyword

Home Products Services Case Studies About Us Contact Us Request Information Blog

PRODUCTS
Air Compressor Works
Kaeser Compressors

Reciprocating / Piston Air Compressor Works » Basics

Compressors
Search
Vacuum, Medical Air &
Dental Systems
Compressed Air Basics, Part 6: Claw Compressors and Archive
Portable Air
Compressors Vacuum Pumps 2016 (3)
Compressed Air Thu 17th Apr 2014 at 5:13pm, 0 comments May (2)
Treatment & Breathing
Air Systems
April (1)
2015 (1)
Nitrogen Systems &
Generators January (1)
2014 (26)
Heat Transfer & Chilled
Water Products October (1)
Tanks & Piping
September (2)
August (1)
Electric Motors
July (3)
Lubricant June (2)
Parts & Accessories May (4)
Services April (5)
March (3)
Industry Links
February (3)
Helpful Information & Links
January (2)
Employment Opportunities 2013 (10)
In most compressed air training classes and seminars, the rotary claw pump is usually only
Used & Rebuilt Equipment November (4)
mentioned in passing, if at all. In most of the applications where claw compressors and vacuum
pumps can be used, rotary vanes or rotary lobes are more common. However, a claw pump can October (3)
often provide a large amount of energy savings when sized correctly. August (1)
May (2)
24 Hour Emergency We decided that instead of just lumping them in a post under "other," we'd highlight them in a
Service Available separate post.

Categories

Certifications Here is how a claw compressor works. It is a rotary compressor with two Advanced (2)
claw­shaped rotors. They turn in opposite directions in the housing. They
don't touch but the clearance is very, very small. As the claw moves over Basics (19)
State Certified Mechanical
Contractor ­ License the inlet, air is sucked into the compression chamber. As the rotors Energy Savings (10)
#CMC1249580 revolve, it reduces the volume of the trapped air, which causes the
pressure to rise. Local News (1)
Florida Healthcare Maintenance (3)
Engineering Association
The claw pump is another "oil­free" technology. There is no oil in the Tips (1)
Kaeser Factory Certified compression chamber, only in the gearbox.
Compressed Air Challenge
Certification of Completion

Usually claw pumps are used as vacuum pumps or as blowers. What I mean by the term "blower"
is a compressor that puts out a low pressure at a high volume. Of course low pressure and high
volume are relative terms. What we're comparing it to in this case are the technologies we
reviewed before ­ piston, screw, and scroll. For the same amount of energy a blower will give you
a lot more volume, but at a considerably lower pressure. Piston, screw, and scroll compressors
are mostly used for pressures above 80 psi. When used as a pressure pump, the claw is usually
for pressures below 30 psi. Every technology has their "sweet spot" where they perform well
compared to the competition.

A lot of customers don't know that the claw pumps exist, but they're great for certain situations.
Rotary vane and rotary lobe tend to dominate the market for these low pressure applications,
because those pumps have been around for a long time and the customers are familiar with the
technology.

However, if you're in the market for a vane or lobe pump, you may want to consider a claw pump,
because there may be some benefits.

Here are the benefits of a claw:

1. In most cases you use less horsepower to provide the same amount of air or vacuum that you
would from the claw's major competitors ­ the vane and lobe pumps.

2. The maintenance is extremely low.

3. 100% duty cycle.

A good example of this is the Rietschle VLR­301 vacuum pump. At 7.5hp it can produce the same
amount of volume that Rietschle's 10 hp vane pump can do (and the 10hp vane pumps of the
competitors). Additionally with the vane pump, you're replacing about a gallon of oil at least twice
 a year ­ sometimes as much as four times per year. With the VLR­301, you replace the gear oil
every 20,000 hours of running time and it's only about a quart.

So that sounds great, what's the catch?

The drawbacks are:

1. Higher initial cost. In the example above the 7.5hp VLR­301 costs a couple of thousand more
than Rietschle's 10hp vane pump. However, that's made up later in energy savings and
maintenance costs. If you look long term, or even medium term, this isn't a drawback, because
over the course of a few years, your overall cost is less.

2. In the instance above, the VLR­301 cannot pull a full vacuum. It can pull a lot, but it can't pull
the vacuum that a vane pump can. If you needed a full 29 inHg, then you'd have to go with the
vane pump. For a more general drawback of claw technology as a whole, it's designed around its
sweet spot of power, flow, and pressure/vacuum. When you hit that sweet spot, it's usually the
best option. If you're too far outside that sweet spot, it may not be able to do what's asked of it. It
needs to be sized correctly by a professional.

So in what situations should you look for a claw pump? Here's a list of good applications for it:

Central vacuum systems

Chemical industry ­ gas compression
Aeration
Drying
Dust extraction
Gas compression
Soil remediation
Drying systems
Dust extraction systems
Industrial furnaces
Medical vacuum
Packaging
Pneumatic conveying
Printing industry
Woodworking industry
Clamping
Dust extraction
Holding

Claw pumps seem to be exceptionally good fits for the printing industry, soil remediation, medical
vacuum, bulk material handling, CNC machines and vacuum hold­down.

Again with any technology, it has a sweet­spot where it performs the best. Claw sizing is more
advanced than your typical compressor installation. I highly advise you contact the experts before
you buy one. Also, if you ask for a claw pump, and the distributor doesn't ask a bunch of
questions on why you need that pump and what it's used for ­ you should probably get a quote
from somewhere else. That company just wants to sell you equipment with no regard on whether
it's right for you or not. They just want to make a quick buck and run ­ they're not looking to be
your compressed air partner.

Add Comment
Name:

Comment:

(This will be reviewed before appearing on the page)

request new code

Please enter the code above:

Submit
Back to previous page

Air Compressor Works • 1956 West 9th St., Riviera Beach, FL 33404 • Toll Free: 800­345­4364 • Ph: 561­844­4559 • Fx: 561­844­8247 • [email protected] • Privacy • Sitemap
Site created by ThomasNet Web Solutions