TPRA2M1-1-U-CE Thermistor Protection Relay

Features :
! PTC Input
! LED Indication : Power ON, Trip, Open, Short
! DIN Rail Mount
! DPDT Relay Output

Certifications :

52.5mm (Width)

Display Specifications Auxiliary Supply Specifications

LED Indication 1. GREEN : Power ON Indication Supply Voltage 95-270V AC

2. YELLOW : Sensor Indication Frequency 50-60 Hz
3. RED : Relay status Power consumption Approx. 3 Watts @ 230VAC
Initialization time 3 seconds
Input Specifications
Sensor type PTC Environmental Specifications

Temperature Operating : 0o to 50o C

Output Specifications Storage : -20 to 70°C
Type of contact DPDT Humidity (non-condensing) 10% to 95% RH
Contact rating 8A 250VAC
Contact material AgSnO2 Mechanical Specifications
Max switching current 8A
Electrical life 1x105 Operations Mounting Din Rail Mounting (size 35mm)
Mechanical life 1x107 Operations Type of connection Terminal screw - 16A rating
Dimension 60 x 35 x 90mm
Housing 2M
Functional Specifications
Weight 115 g
Relay operating mode Failsafe mode Type of protection IP20
Non-failsafe mode No of terminals 11 (L, N, REMOTE, GND,
Reset Auto / Manual / Remote PTC, NO1, NC1, C1, NO2, NC2, C2)
Response time maximum <100ms

Ordering Information
Sensor Specifications
Product Code Output 1 Supply Voltage Certification
Sensor Short : < 39Ω (±1Ω)
TPRA2M1-1-U-CE RELAY 95-270V AC / DC
Sensor Healthy : 42Ω (±1Ω) to <3.8KΩ(±40Ω)
Sensor Trip : ≥3.8KΩ (±40Ω) to <5.6KΩ (±60Ω)
Sensor Open : ≥5.6KΩ (±60Ω) & Above
Sensor Cut-in : ≤1.5KΩ (±40Ω)

[Link] 1
 TPRA2M1 MECHANICAL INSTALLATION LED INDICATION
OP645-V01
selec Operating Instructions MECHANICAL
Mounting : Din Rail Mounting (size 35mm) FRONT SIDE

Type of connection : Terminal screw-16A rating

Dimension : 60mm x 35mm x 90mm ON S R
Housing : 2M
Weight : 115 g
No of terminals : 11 (L, N, REMOTE, GND, PTC

67.5mm
NO1, NC1, C1, NO2, NC2, C2)

90mm
90mm

45mm
Green Yellow Red

WIRING GUIDELINES

FEATURES WARNING PTC SENSOR CHARACTERISTICS

35mm
1. To prevent the risk of electric shock power supply
!Auto / Manual mode selection to the equipment must be kept OFF while doing
!Failsafe / Non-failsafe mode selection
CONNECTION DIAGRAM
the wiring arrangement. MOTOR
!Self check mode RPTC(Ω)
2. Wiring shall be done strictly according to the R
!Remotely controllable terminal layout with shortest connections. Confirm Y
B
that all connections are correct. OFF

SPECIFICATIONS CAUTION
ON

1. To ensure the safe operation of unit, check the MOTOR STARTER 5600
AUXILIARY SUPPLY wiring and connections.
Voltage : 90-270V AC / DC 2. It is recommended to test the unit periodically to
Frequency : 50-60 Hz satisfy the regulations. 26 25 28 15 18
16
Power consumption : Approx. 3 Watts NC COM NO NC COM NO 4100
@230V AC SAFETY PRECAUTIONS
Initialization time : 3 seconds 1000
All safety related codifications, symbols and
L N R1 S1 S2
LED INDICATIONS instructions that appear in this operating manual or
1. GREEN : Power ON indication on the equipment must be strictly followed to ensure
2. YELLOW : Sensor indication the safety of the operating personnel as well as the
Remote
3. RED : Relay status instrument.
If the equipment is not used in a manner specified
by the manufacturer it might impair the protection Tsense-10 Tsense Tsense+10 TPTC( oC)
RELAY OPERATING MODES
1. Failsafe mode provided by the equipment.
selec SENSOR SPECIFICATIONS
2. Non-failsafe mode ON S R
Read complete instructions prior to installation.
RELAY OUTPUT 1. Sensor Short : ≤ 40Ω
Type of contact : DPDT TERMINAL DIAGRAM TPRA2M1

Contact rating : 8A@250V AC 2. Sensor Healthy : ≥44Ω (±3Ω) to

RELAY 1 PRG
<3.8KΩ(±150Ω)
Contact material : AgSnO2
Max switching current : 8A 26 25 28 16 15 18
Electrical life : 1x105 Operations 3. Sensor Trip : ≥3.8KΩ (±150Ω) to
TPRA2M1

Mechanical life : 1x107 Operations NC COM NO NC COM NO <5.5KΩ (±150Ω)

Power LED
Programming and reset key 4. Sensor Open : ≥5.5KΩ (±150Ω) & Above
ENVIRONMENTAL
Temperature range Sensor indication
Operating : 0o to 55o C L N R1 S1 S2 [Link] Cut-in/Recovery : ≤1.5KΩ (±60Ω)
Storage : -20o to 70o C Relay status
PTC
Humidity : 10% to 95% RH

Remote Key

Doc. name : OP INST TPRA2M RoHS OP645-V01(Page 1 of 2)

 DESCRIPTION 2. MANUAL MODE : PROGRAMMING SCHEME
Press the key when the R-LED starts slow blinking
Thermistor motor protection relay is used for To enter programming mode, short terminals S1 and S2 to go to Sensor Short conditon. Make sure
i.e. when the sensor condition is Cut-in. After
controlling motor with the help of PTC sensors. to remove all connections done to the relay. Now, press the PRG key for 5 seconds. Once, we enter
pressing the key, the relay goes into Healthy state.
The PTC sensor changes it's resistance with programming mode, each mode has 10 seconds to be configured. To make changes press the front
respect to the temperature of motor. The PRG key but in that time window only. After 10 seconds, it will directly go to the next mode which is
resistance is measured by the thermistor motor Sensor R-LED R-LED indicated by fast blinking of both S & R LEDs. The changes are auto-saved and retained.
Non-Failsafe S-LED
protection relay and depending upon the sensor condition Failsafe Note: Remote key can also be used for programming.
condition the relay is switched. Short
Following are the sensor conditions which are LED indication
classified depending upon the resistance: Healthy Mode PRG key DURATION
1. Sensor Short : Sensor is short / damaged. S R
Trip
S-LED blinks slowly.
We can enter the programming mode only when Enter
Open Pressed for 5 seconds 3 seconds
configuration
in Sensor Short condition. To enter into the
programming mode keep the PRG key pressed Cut-in(Key
for 5 seconds. not press)
2. Sensor Healthy : The motor is running safely. WARRANTY
USER GUIDE / LIMITATIONS OF LIABILITY : Relay ON
Relay check Press key to toggle relay
R-LED is ON in fail-safe mode & vice versa. ON 10 seconds
mode : Relay OFF
3. Sensor Trip : When the motor exceeds it's Selec warrants the products to be free from
temperature beyond it's safety limit, it is in trip defects in the materials and workmanship for a
condition. The moment Trip condition is reached, period of one year (or other period specified, if any)
the S-LED, turns on and the relay changes it's from the date of sale by Selec. Next mode NA 3 seconds
state automatically. It stays in Trip condition until The warranty does not apply to defects
the motor cools down and reaches Cut-in. resulting from any action of the buyer, including but
Sensor Cut-in : After the motor cools down, it not limited to improper handling, operating the
product outside the specification limits or Auto / Press key to select mode : Auto
reaches cut-in condition. The relay switches
unauthorized disassembling / altering of the Manual •Auto OFF 10 seconds
automatically, in Auto Mode. Whereas, in Manual
product. The warranty shall be VOID if the product selection •Manual : Manual
mode, the user has to press the front PRG key or
the Remote Key, momentarily, when in Cut-in shows evidence of having been tampered or being
condition. Press the PRG key momentarily when damaged due to usage in corrosive environment ;
R-LED is blinking. or current, heat, moisture or vibration ; improper Next mode NA 3 seconds
5. Sensor Open : Sensor is open / break. S-Led specification ; wrong usage in an application ;
blinks fast. misuse or other operating conditions outside of
Selec's control.
Press key to select mode : Failsafe
Selec shall not be responsible for special, Failsafe &
LED STATUS indirect or consequential damages, loss of profits or Non-failsafe •Failsafe 10 seconds
: Non-
commercial loss in any way connected with the selection •Non-Failsafe mode
ON failsafe
products, whether such claim is based on contract,
OFF warranty, negligence or strict liability.
In no event shall the responsibility of Selec
Slow Blink for any act exceed the individual price of the
product on which liability is asserted.
Fast Blink In no event shall Selec be responsible for
warranty or other claims regarding the products
FUNCTIONING unless Selec's analysis confirms that the products
1. AUTO MODE : were properly handled, stored, installed and
After cut-in the relay switches its state maintained and not subject to contamination,
automatically to Healthy state. abuse, misuse or inappropriate modification or
(Specifications are subject to change, since development is a
R-LED repair. continuous process.)
Sensor R-LED
Non-Failsafe S-LED
condition Failsafe Selec Controls Pvt. Ltd., India
Short Factory Address :
ORDER CODE INFORMATION EL-27/1, Electronic Zone, TTC Industrial Area, MIDC, Mahape,
Healthy
Product Supply Navi Mumbai - 400 710, INDIA.
Certification
Trip Tel. No. : +91-22-41 418 468/452 | Fax No. : +91-22-28471733
Toll free : 1800 227 353 (BSNL/MTNL Subscribers only)
Open TPRA2M1-1-U 90-270V AC/DC
Website : [Link] | Email : sales@[Link]
Doc. name : OP INST TPRA2M RoHS OP645-V01(Page 2 of 2)