Scribd
Upload
24 views1 page

Carboguard 824 Epoxy Primer Data Sheet

Carboguard 824 is a VOC compliant epoxy polyamide primer designed for harsh marine and industrial environments, suitable for immersion service. It features a dry film thickness of 3-4 mils per coat and has a solids content of 67% by volume. The product requires thorough surface preparation and is qualified under military specifications.

Uploaded by

Longtomahawk
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
24 views1 page

Carboguard 824 Epoxy Primer Data Sheet

Carboguard 824 is a VOC compliant epoxy polyamide primer designed for harsh marine and industrial environments, suitable for immersion service. It features a dry film thickness of 3-4 mils per coat and has a solids content of 67% by volume. The product requires thorough surface preparation and is qualified under military specifications.

Uploaded by

Longtomahawk
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd

®

Carboguard 824 Primer (F-150)


PRODUCT DATA SHEET

S E L E C T I O N & S P E C I F I C AT I O N D ATA
Generic Type Epoxy Polyamide

Carboguard 824 is a VOC compliant, two coat, epoxy polyamide system for use where marine
coating regulations are restricted to a maximum VOC of 340 g/l or 2.8 lb/gal. The system is
specifically formulated for use in immersion service; it is highly versatile and may also be used
Description
as an intermediate coating for a variety of industrial applications. Carboguard 824 is for use over
properly prepared steel and aluminum substrates that will be subject to exposure in harsh industrial
and marine environments.

• Immersion grade epoxy


• Excellent for harsh marine or industrial exposures
Features
• Qualified under MIL-DTL-24441D Type IV
• Approved for UFGS 09 97 13.27

Color Green F-150 (2394)

Dry Film Thickness 3 - 4 mils (76 - 102 microns) per coat

Solids Content By Volume 67% +/- 2%

Theoretical Coverage 1080 ft²/gal @ 1 dry mil


Rates

1075 ft²/gal at 1.0 mils (26.4 m²/l at 25 microns)


Theoretical Coverage 358 ft²/gal at 3.0 mils (8.8 m²/l at 75 microns)
Rate 269 ft²/gal at 4.0 mils (6.6 m²/l at 100 microns)
Allow for loss in mixing and application.

VOC Values As Supplied : 2.29 lbs/gal (274 g/l)

Continuous: 200°F (93°C)


Dry Temp. Resistance
Non-Continuous: 250°F (121°C)

Limitations Epoxies may lose gloss, discolor and chalk when exposed to sunlight.

S U B S T R AT E S & S U R F A C E P R E PA R AT I O N
All surfaces must be thoroughly cleaned to remove dirt, grease, mill scale, loose rust, chalk, and
General any other contaminants that can reduce adhesion via SSPC-SP1 solvent cleaning. Primer required
for most substrates.

All previously painted surfaces should be cleaned thoroughly to remove surface contamination.
Previously Painted Rinse well and allow to dry. Scrape loose, scaly, peeling paint and sand the edges smooth, remove
Surfaces any rust and scale from ferrous metal. If the paint is glossy, sand to dull the surface. Test for
compatibility with existing coatings.

Abrasive blasting is recommended to remove rust and mill scale. Solvent clean surfaces according
to SSPC-SP1, then a commercial blast to SSPC-SP6 for mild exposures. For immersion service
Metal
and severe environments, solvent clean surfaces according to SSPC-SP1 first, then near-white
blast to SSPC-SP10.

March 2025 207F Page 1 of 3

You might also like