For details about certified products

conforming to international standards,

visit us at [Link].

5 Port Solenoid Valve

Body Ported

Series VZ5000
How to Order VK

r
so
VZ

es
pr
up
es
ag

ize
VF
n

olt

de
io

ts
ry

ev
at

ge

rri

or
nt
tu

rg

pe
n

ve
ta

le

)p
tio

/su
ac

ty
l

lo
vo

ca

(B
op

VFR

ht
of

ad
ua

n
tr i

/2
lig
ed

io
dy
e

re
ec

an

A)
ith

pt
at
p

Bo

Th
Ty

El

4(
M
W

O
R

Body ported VZ5 1 2 0 5 L 01 VP4

VZS
Type of actuation

Option
2 position single solenoid F: With foot bracket
(2 position single type only)
VFS
Body option

1 0: Individual exhaust VS4
for the pilot valve
VQ7
2 position double solenoid
EVS
2 Note) Do not remove the
3(R) port
PE port factory installed VFN
bracket from models
3: Common exhaust type with the bracket
for main and pilot valve option.
3 position closed center

Thread type
3 Nil Rc
F G
PE port
3(R) port N NPT
T NPTF
3 position exhaust center

4
Rated voltage

4(A), 2(B) port size
1 100 VAC, 50/60 Hz 01 Rc 1 8
2 200 VAC, 50/60 Hz C6 One-touch fitting for ø6
3 position pressure center
3∗ 110 VAC, 50/60 Hz C8 One-touch fitting for ø8
4∗ 220 VAC, 50/60 Hz Note) P, R1, R2 port: Rc 1/8
5 5∗ 24 VDC
6 12 VDC
9∗ Other
Manual override
∗ Option
Nil: Non-locking B: Locking type B C: Locking type C
Electrical entry

push type (Slotted) (Manual)
Grommet L plug connector M plug connector DIN terminal
G: Lead wire L: With lead wire M: With MN: Without D: With connector
length (Length 300 mm) lead wire lead wire
300 mm (Length 300 mm)

H: Lead wire LN: Without LO: Without MO: Without DO: Without
length lead wire connector connector connector
600 mm
Light/Surge voltage suppressor
Nil None
Z∗ With light/surge voltage suppressor
S With surge voltage suppressor
∗ Type “LN”, “MN”: With 2 sockets. ∗ Not available for “GZ”, “HZ” and “DOZ”

3-3-53
Series VZ5000
Specifications
Applicable for cylinder Fluid Air
actuation (up to ø50). Operating pressure
2 position single 0.15 to 0.7
2 position double 0.1 to 0.7
range (MPa)
Compact size 3 position 0.15 to 0.7
(Width: 18 mm) Ambient and fluid temperature (°C) –10 to 50°C (No freezing. Refer to page 3-13-4.)
Response time (ms) (1) 2 position single, double 20 or less
Low power consumption: (at the pressure of 0.5 MPa) 3 position 50 or less
1.8 W DC Max. operating 2 position single, double 10
frequency (Hz) 3 position 3
Effective area Refer to the table below.
Manual override (2) Non-locking push type, Locking slotted type, Locking lever type
Pilot exhaust method Individual pilot exhaust type, Common exhaust (pilot and main valve) type
Lubrication Not required
Mounting orientation Unrestricted
Impact/Vibration resistance (m/s2 )(3) 300/50
Enclosure Dustproof
Note 1) Based on dynamic performance test, JIS B 8375-1981. (Coil temperature: 20°C, at
rated voltage, without surge suppressor)
Note 2) When operating the locking type manually, apply torque of 0.2 N·m or less.
Note 3) Impact resistance: No malfunction occurred when it is tested with a drop tester in the
axial direction and at the right angles to the main valve and
armature in both energized and de-energized states every once for
each condition. (Values at the initial period)
Vibration resistance: No malfunction occurred in a one-sweep test between 45 and 2000
Hz. Test was performed at both energized and de-energized states
in the axial direction and at the right angles to the main valve and
armature. (Values at the initial period)

Solenoid Specifications ∗ Option

Grommet (G)/(H), L plug connector (L),
Electrical entry
M plug connector (M), DIN terminal (D)
AC 50/60 Hz 100, 200, 24∗, 48∗, 110∗, 220∗
Coil rated voltage (V)
DC 24, 6∗, 12∗, 48∗
Allowable voltage fluctuation (%) –15 to +10% of rated voltage
Power consumption (W) Note) 1.8 (With indicator light 2.1)
[Current mA] DC
[24 VDC: 75 (With indicator light 87.5)]

Inrush 100 VAC: 45/50 Hz, 42/60 Hz

Refer to pages 3-3-60 to 3-3-65 for manifold use. 4.5/50 Hz, 4.2/60 Hz
Apparent power (VA) Note) 200 VAC: 22.5/50 Hz, 21/60 Hz
AC
[Current mA] 100 VAC: 35/50 Hz, 30/60 Hz
Holding 3.5/50 Hz, 3/60 Hz
200 VAC: 17.5/50 Hz, 15/60 Hz
Surge voltage suppressor DC: Diode, AC: ZNR
Indicator light DC: LED (Red), AC: Neon bulb
Note) At rated voltage

Made to Order Specifications

(For details, refer to page 3-3-85.)

3-3-54
 5 Port Solenoid Valve
Body Ported Series VZ5000
Flow Characteristics/Weight
Port size Flow characteristics Note)
Weight (g)
Valve model Type of actuation 1, 5, 3 4, 2 1
4/2 (P
A/B) 4/2
5/3 (A/B
EA/EB)
(P, EA, EB) (A, B) C [dm3/(s·bar)] b Cv C [dm3/(s·bar)] b Cv Grommet
2 Single 120
position 2.2 0.36 0.58 2.4 0.34 0.63
Double 160
3 Closed center Rc 1/8 Rc 1/8 1.8 0.37 0.45 2.0 0.35 0.49
VZ520--01 position Exhaust center 1.2 0.50 0.34 3.0[1.3] 0.35[0.52] 0.73[0.39] 160
Pressure center 3.0 [0.83] 0.37[0.50] 0.78[0.25] 1.8 0.37 0.45
2 Single 120
position 1.6 0.33 0.4 2.2 0.32 0.53
Double C6 160 VK
Closed center Rc 1/8 (One-touch 1.4 0.27 0.35 1.9 0.33 0.49
3
VZ520--C6 Exhaust center fitting for ø6) 1.1 0.37 0.27 2.5[1.3] 0.32[0.54] 0.61[0.38] 160
position
Pressure center 1.8 [0.78] 0.36[0.40] 0.45[0.22] 1.6 0.30 0.39
VZ
2 Single 120
position Double C8
2.0 0.39 0.52 2.3 0.34 0.61
160 VF
Closed center Rc 1/8 (One-touch 1.7 0.35 0.42 2.0 0.29 0.49
3
VZ520--C8 position Exhaust center fitting for ø8) 1.2 0.38 0.33 2.6[1.3] 0.35[0.49] 0.67[0.38] 160 VFR
Pressure center 1.9 [0.86] 0.57[0.46] 0.59[0.25] 1.7 0.39 0.42
Note) [ ]: Denotes the normal position. Exhaust center: 4/2
5/3, Pressure center: 1
4/2 VP4
VZS
Use as a guide for selection.
Cylinder Speed Chart Please confirm the actual conditions with SMC Sizing Program. VFS
Bore size
Series CJ2
Average Pressure 0.5 MPa
Series CM2
Pressure 0.5 MPa
Series MB, CA1 Note)
Pressure 0.5 MPa
VS4
Series speed Load factor 50%
Load factor 50% Load factor 50%
(mm/s) Stroke 60 mm
Stroke 300 mm Stroke 500 mm VQ7
ø6 ø10 ø16 ø20 ø25 ø32 ø40 ø40 ø50 ø63 ø80 ø100
800
700 605
749
610
Perpendicular, EVS
600 560 558 upward actuation
500 475 487 Horizontal actuation
VZ5120-01 400 286 310
398 364 360
301
379 386 VFN
300 214 204 235 252 252
200 130 157 103
159
100
0
∗ It is when the cylinder is extending that is meter-out controlled by speed controller which is directly connected with cylinder, and its needle valve
with being fully open.
∗ The average velocity of the cylinder is what the stroke is divided by the total stroke time.
∗ Load factor: ((Load weight x 9.8)/Theoretical force) x 100%
Note) The Series CA1 has been changed to the Series CA2.

Conditions
Body ported Series CJ2 Series CM2 Series MB
Tube bore x Length ø6 x 1 m ø6 x 1 m ø12 x 1 m
VZ5120-01 Speed controller AS2301F-06 AS3301F-06 AS4001F-12
Silencer AN110-01 AN200-02

3-3-55
Series VZ5000
Construction
2 position single 2 position double

De-energized
De-energized

3 position closed center 3 position closed center/exhaust center/pressure center

De-energized De-energized

3 position exhaust center

3 position pressure center (This figure shows a closed center type.)

Component Parts Replacement Parts

No. Description Material Note No. Description Material Part no. Note
q Body Aluminum die-casted Platinum silver u Solenoid assembly Epoxy/Stainless steel DXT170-C-
w Piston plate Resin Black Common with
i O-ring NBR 13 x 11 x 1
e Piston Resin Series VZ 13 000
r Spool valve Aluminum, HNBR
t End cover Resin Black painted
y Spool spring Stainless steel

3-3-56
 5 Port Solenoid Valve
Body Ported Series VZ5000
2 Position Single

VZ5120 Foot bracket

Grommet (G), (H) VZ5120-GH -01-F
H -01
VZ5120-G
(Mounting
hole)

VK
Manual override
(Mounting hole for manifold) (Non-locking)
VZ

(Lead wire length)

VF

G: 300 mm
H: 600 mm
(Mounting hole)
VFR
VP4
VZS
VFS
VS4
(PE port)
VQ7
EVS
VFN
(Piping port)

L plug connector (L) M plug connector (M)

VZ5120-L-01 VZ5120-M-01
(Lead wire length)

≅300
(Lead wire length)
≅300

: With light/surge voltage suppressor

DIN terminal (D) Built-in One-touch fittings

VZ5120-D-01 VZ5120--C6
C8
C8: MAX. 6.5

MAX. 10
C6: MAX. 6

2-One-touch fitting
(A, B port)
Applicable tubing model
Applicable cable O.D. C6: T0604
C8: T0806
ø3.5 to ø7

3-3-57
Series VZ5000
2 Position Double
VZ5220

Grommet (G), (H)

H-01
VZ5220-G

Manual
override
(Mounting hole for manifold) (Non-locking)

(Lead wire length)

G: 300 mm
H: 600 mm
(Mounting hole)

(PE port)

(Piping port)

L plug connector (L) M plug connector (M)

VZ5220-L-01 VZ5220-M-01
(Lead wire length)

≅300
(Lead wire length)
≅300

: With light/surge voltage suppressor

DIN terminal (D) Built-in One-touch fittings

VZ5220-D-01 VZ5220-- C6
C8: MAX. 6.5

C8
C6: MAX. 6

MAX. 10
2-One-touch fitting
(A, B port)
Applicable tubing model
C6: T0604
C8: T0806

Applicable cable O.D.

ø3.5 to ø7

3-3-58
 5 Port Solenoid Valve
Body Ported Series VZ5000
3 Position Closed Center/Exhaust Center/Pressure Center
VZ5320

Grommet (G), (H) (Mounting hole for manifold)

3
VZ5 45 20-G
H -01 Manual override
(Non-locking)

VZ5420
VK
VZ
VF

(Lead wire length)

VZ5520 VFR

G: 300 mm
H: 600 mm
(Mounting hole)
VP4
VZS
VFS
VS4
VQ7
(PE port)
EVS
VFN

(Piping port)

L plug connector (L) M plug connector (M)

(Lead wire length)

3 3
VZ5 4 20-L-01 VZ5 4 20-M-01
5 5
≅300
(Lead wire length)
≅300

: With light/surge voltage suppressor

DIN terminal (D) Built-in One-touch fittings

3 3
VZ5 4 20-D-01 VZ5 4 20-- C6
5 5 C8
C8: MAX. 6.5
C6: MAX. 6

2-One-touch fitting
Applicable cable O.D. (A, B port)
ø3.5 to ø7 Applicable tubing model
C6: T0604
C8: T0806

3-3-59
 Series VZ5000/Body ported
Manifold Specifications
Manifold Standard
Manifold Specifications
Model Type 20 Type 21
Manifold type Single base/B mount
P(SUP)/R(EXH) Common SUP/Common EXH
Valve stations 2 to 15 stations 2 to 20 stations
4(A), 2(B) port location Valve
1(P), 3/5(R) port Rc 1 8 Rc 1 4
Port size
4(A), 2(B) port Rc 1 8 , C6, C8

Flow Characteristics
Port size Flow characteristics
Manifold 1(P), 5/3(R) 2(B), 4(A) 1
4/2 (P
A/B) 4/2
5/3 (A/B
R)
port port 3
C [dm /(s·bar)] b Cv C [dm3/(s·bar)] b Cv
VV5Z5-20-01 1/8 1/8 2.2 0.35 0.57 2.3 0.26 0.55
VV5Z5-20-C6 1/8 C6 1.4 0.32 0.37 2.0 0.25 0.49
VV5Z5-20-C8 1/8 C8 1.7 0.38 0.45 2.1 0.25 0.51
VZ52
VV5Z5-21-01 1/4 1/8 2.1 0.36 0.55 2.3 0.26 0.54
VV5Z5-21-C6 1/4 C6 1.4 0.32 0.36 2.1 0.24 0.50
VV5Z5-21-C8 1/4 C8 1.8 0.37 0.50 2.1 0.20 0.50
Note) Value at manifold base mounted, 2 position single operating

How to Order Manifold

Instruct by specifying the valves and blanking plate assembly to be mounted on the manifold along
with the manifold base model no.
(Example) VV5Z5-20-031···········1 pc. (Manifold base)
∗VZ5120-5G-01·········2 pcs. (Valve)
∗DXT199-22-1A·········1 pc. (Blanking plate assembly)
The asterisk denotes the symbol for assembly. Prefix it to the part nos. of the solenoid valve, etc.

Flat Ribbon Cable Manifold

Flat Ribbon Cable Manifold Specifications
• One-touch wiring to Model Type 21P
consolidate connection of Manifold type Single base/B mount
P(SUP), R(EXH) Common SUP/Common EXH
external wires. Valve stations 3 to 12 stations
• Clean appearance 4(A), 2(B) port location Valve
The flat cable provides wiring on a 1(P), 3/5(R) port Rc 1 4
Port size
printed circuit board to the individual 4(A), 2(B) port Rc 1 8 , C6, C8
valves at the manifold base, enabling Socket: 26 pins MIL, with strain relief
Applicable flat ribbon cable connector
(Conforming to MIL-C-83503)
the consolidation of external wiring at
Internal wiring +COM (For –COM, please contact SMC separately.)
a touch through a 26 pins MIL 1
connector. Applicable solenoid valve VZ523- 35 MOZ-VZ3- C6
01
6 C8

Rated voltage 100 VAC 50/60 Hz, 110 VAC 50/60 Hz, 24 VDC, 12 VDC
Note) Withstand voltage specification of wiring unit part is equivalent to JIS C 0704 class 1.

Flow Characteristics
Port size Flow characteristics
Manifold 1(P), 5/3(R) 2(B), 4(A) 1
4/2 (P
A/B) 4/2
5/3 (A/B
R)
port port C [dm3/(s·bar)] b Cv C [dm3/(s·bar)] b Cv
VV5Z5-21P-01 1/4 1/8 2.1 0.36 0.55 2.3 0.26 0.54
VV5Z5-21P-C6 VZ523 1/4 C6 1.4 0.32 0.36 2.1 0.24 0.50
VV5Z5-21P-C8 1/4 C8 1.8 0.37 0.50 2.1 0.20 0.50
Note) Value at manifold base mounted, 2 position single operating

How to Order Manifold

Instruct by specifying the valves, blanking plate assembly and connector assembly to be mounted on
the manifold along with the manifold base model no.
(Example) VV5Z5-21P-07············1 pc. (Manifold base)
∗VZ5123-5MOZ-C8···· 3 pcs. (Valve)
∗VZ5223-5MOZ-C8···· 3 pcs. (Valve)
∗DXT199-22-3A········· 1 pc. (Blanking plate assembly)
∗DXT192-52-1-4A······ 3 pcs. (Connector assembly)
∗DXT192-52-2-4A······ 3 pcs. (Connector assembly)
The asterisk denotes the symbol for assembly. Prefix it to the part nos. of the solenoid valve, etc.

3-3-60
 5 Port Solenoid Valve
Body Ported Series VZ5000
Common SUP/Common EXH
Type 20 How to Order
4(A), 2(B) port
VV5Z5 20 05 1
Stations P, R port
1(P) port 02 2 stations thread type

···
···
Rc 1/8 Nil Rc
Applicable solenoid
15 15 stations 00F G
3/5(R) port valve
Rc 1/8 00N NPT G 01 VK
00T NPTF VZ52- LM - C6
D C8
Note) For more than 6 stations, supply air to both sides of P port and exhaust air from both sides of R port.
Applicable blanking plate VZ
assembly
Type 21 How to Order
DXT199-22-1A VF
Applicable individual EXH
4(A), 2(B) port
VV5Z5 21 05 1 spacer assembly
DXT199-29-1A VFR
Stations P, R port
1(P) port
02 2 stations thread type VP4

···
···
Nil Rc
Rc 1/4 20 20 stations 00F
00N
G
NPT
VZS
3/5(R) port 00T NPTF
Rc 1/4 VFS
Note) For more than 10 stations, supply air to both sides of P port and exhaust air from
both sides of R port.
VS4
Flat Ribbon Cable Type 21P How to Order Applicable solenoid
valve
1
VQ7
01
VV5Z5 21P 05 VZ523- 35 MOZ-C6
6 C8
EVS
Applicable blanking plate
Stations P, R port assembly
4(A), 2(B) port 03 3 stations thread type DXT199-22-3A VFN
···
···

Nil Rc Applicable connector

12 12 stations 00F G assembly
00N NPT DXT192-52-1- ∗ A
1(P) port (For 2 position single)
00T NPTF
Rc 1/4 DXT192-52-1- ∗ A
(For 2 position double, 3
position)
3/5(R) port ∗ 1: 100 VAC, 3: 110 VAC,
Rc 1/4 4: DC
For “How to order
applicable connector
assemblies”, refer to
page 3-3-7.
Note) For more than 10 stations, supply air to both sides of 1(P) port and exhaust air from
both sides of 3 and 5(R) port.

3-3-61
Series VZ5000
Option

Combinations of Solenoid Individual EXH Spacer Assembly Installation of the VZ500 Valve
Valve, Manifold Gasket and DXT199-29-1A on the VZ5000 Manifold
Manifold Base • Use of an adaptor plate makes it possible
to mount Series VZ500 on the manifold
Round head base of Series VZ5000.
Round head combination screw combination screw • The mounting direction is shown in the
diagram below. Mount the solenoid so that
(With springM3washer
x 31
) (M3
With spring washer)
x 47
it will be on the same side as the single
solenoid of the Series VZ5000.

Adapter plate assembly

DXT201-3-1A
Round head
combination screw

Gasket (M3
With spring washer )
x 31

Individual
EXH spacer

Applicable base 2-Rc 1/8

VV5Z5-20 Gasket
(EXH port)
VV5Z5-21
VV5Z5-21P

Gasket

Round head
combination screw
Applicable base
VV5Z5-20
VV5Z5-21 (With springM3washer
x 10
)
Note) Please contact SMC when using an Adapter plate
individual EXH spacer assembly,
an individual or an adapter plate
assembly on VV5Z5-21P.
O-ring

Blanking Plate Assembly

DXT199-22-1A DXT199-22-3A Applicable base
VV5Z5-20
Round head
combination screw VV5Z5-21
Round head combination screw

(M3 (M3
With spring washer )
x8
With spring washer )
x8

Blanking plate Blanking plate

Gasket

Applicable base Gasket

VV5Z5-20
VV5Z5-21

Dust cap
Caution
Applicable base Mounting Screw Tightening Torques
VV5Z5-21P M3: 0.8 N·m

3-3-62
 5 Port Solenoid Valve
Body Ported Series VZ5000
Type 20 Manifold

VV5Z5-20- Station 1
2n-Rc 1/8
(4(A), 2(B) port)
Grommet (G), (H)
(Pitch)

4-ø4.5
(Mounting hole)

VK
VZ
VF

6-Rc 1/8 VFR

(1(P), 3/5(R) port)
PE port VP4
(Pilot EXH)

Manual override
VZS
G: 300 mm
(Non-locking) H: 600 mm
VFS
(Lead wire length)

VS4
VQ7
EVS
VFN

(mm)
Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15
L1 59 78 97 116 135 154 173 192 211 230 249 268 287 306
L2 47 66 85 104 123 142 161 180 199 218 237 256 275 294

L plug connector (L) M plug connector (M) DIN terminal (D) Built-in One-touch fittings
MAX. 10
(Lead wire length)

C6: MAX. 6
≅300

C8: MAX. 6.5

≅300
(Lead wire length)

2n-One-touch fitting
(4(A), 2(B) port)
Applicable tubing model
C6: T0604
C8: T0806

Applicable cable O.D.

ø3.5 to ø7

: With light/surge voltage suppressor

3-3-63
Series VZ5000
Type 21 Manifold

VV5Z5-21- Station 1
2n-Rc 1/8
Grommet (G), (H) (4(A), 2(B) port)

(Pitch)

(Mounting hole)

6-Rc 1/4
(1(P), 3/5(R) port)
PE port

Manual override G: 300 mm

H: 600 mm
(Non-locking)
(Lead wire length)

(mm)
Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
L1 66 85 104 123 142 161 180 199 218 237 256 275 294 313 332 351 370 389 408
L2 46 65 84 103 122 141 160 179 198 217 236 255 274 293 312 331 350 369 388

L plug connector (L) M plug connector (M) DIN terminal (D) Built-in One-touch fittings
MAX. 10
(Lead wire length)
≅300

C6: MAX. 6
≅300 C8: MAX. 6.5
(Lead wire length)
Applicable cable O.D.
ø3.5 to ø7

2n-One-touch fitting
(4(A), 2(B) port)
Applicable tubing model
C6: T0604
C8: T0806

: With light/surge voltage suppressor

3-3-64
 5 Port Solenoid Valve
Body Ported Series VZ5000
Type 21P Manifold

VV5Z5-21P- Station

VV5Z5-21P- Station

VK
Manual override VZ
(Non-locking)
2n-Rc 1/8
(4(A), 2(B) port)
VF
(Pitch) VFR
(Mounting hole)
6-Rc 1/4
VP4
(1(P), 3/5(R) port)
VZS
VFS
VS4
VQ7

Triangle mark EVS

(Light/Surge voltage suppressor)
VFN

(Station n)···························(Station 1)

Connector polarity indicator

Applicable connector: 26 pins MIL
(Conforming to MIL-C-83503)

Built-in One-touch fittings (mm)

Stations 3 4 5 6 7 8 9 10 11 12
L1 88 108.5 129 149.5 170 190.5 211 231.5 252 272.5
L2 68 109 109 129.5 150 170.5 191 211.5 232 252.5

C6: MAX. 6
C8: MAX. 6.5

2n-One-touch fitting
(4(A), 2(B) port)
Applicable tubing model
C6: T0604
C8: T0806

3-3-65
 For details about certified products
conforming to international standards,
visit us at [Link].

5 Port Solenoid Valve

Base Mounted

Series VZ5000
How to Order VK

or
VZ

ss
re
pp
su
n

e
VF

e
io

ag

d
ry
at

ge

rri
lt
nt

vo
tu

ve
lta

le
tio
ac

ge

lo
vo

e
ca
op

Note) Please contact SMC in the case

ur

iz
of

ua
VFR

tri

/S
ed

s
dy
e

ec

an
of without indicator light.

ht

rt
p

at
Bo

Po
Lig
Ty

El

M
R

Note)
VZ5 1 4 3 5 F Z

pe
Plug-in VP4

ty
d
a
re
Th
VZS
Non plug-in VZ5 1 4 0 5 L
VFS
Type of actuation

Thread type
2 position single solenoid Nil Rc VS4
F G
1 N NPT VQ7
T NPTF

Port size
Body option

0: Individual exhaust Nil: Without 01: Rc 1 8
EVS
2 position double solenoid for the pilot valve sub-plate With sub-plate Note)
VFN
2

3(R) port PE port

3 position closed center 3: Common exhaust type 02: Rc 1 4

for main and pilot valve With sub-plate

Note) 5(R1), 3(R2) port: Rc 1 4

3(R) port PE port
3 position exhaust center

Manual override/Plug-in type
Rated voltage
Nil: Non-locking B: Locking type B C: Locking type C
4
push type (Slotted) (Manual)
1 100 VAC, 50/60 Hz
2 200 VAC, 50/60 Hz
3∗ 110 VAC, 50/60 Hz
3 position pressure center 4∗ 220 VAC, 50/60 Hz 1 1

5∗
0 0
24 VDC
5 6 12 VDC
9∗ Other
∗ Option Manual override/Non plug-in type
Electrical entry
Nil: Non-locking B: Locking type B C: Locking type C
Grommet L plug connector M plug connector DIN terminal push type (Slotted) (Manual)
G: Lead wire L: With lead wire M: With MN: Without D: With connector
length (Length 300 mm) lead wire lead wire
300 mm (Length 300 mm)

H: Lead wire LN: Without LO: Without MO: Without DO: Without
length lead wire connector connector connector
600 mm

Light/Surge voltage suppressor
Nil None
Z∗ With light/surge voltage suppressor
S With surge voltage suppressor
∗ Type “LN”, “MN”: With 2 sockets. ∗ Not available for “GZ”, “HZ” and “DOZ”

3-3-67
Series VZ5000
Specifications
Applicable for cylinder Fluid Air
2 position single 0.15 to 0.7
actuation (up to ø50). Operating pressure
2 position double 0.1 to 0.7
range (MPa)
Compact size 3 position 0.15 to 0.7
Ambient and fluid temperature (°C) –10 to 50°C (No freezing. Refer to page 3-13-4.)
(Width: 18 mm) Response time (ms)(1) 2 position single, double 20 or less
Low power consumption: (at the pressure of 0.5 MPa) 3 position 50 or less
Max. operating 2 position single, double 10
1.8 W DC frequency (Hz) 3 position 3
Effective area Refer to the table below.
Non-locking push type, Locking slotted type,
Manual override (2) Locking lever type
Individual pilot exhaust, Common exhaust (pilot and main valve)
Pilot exhaust
Common exhaust port for the pilot and main valve
Lubrication Not required
Mounting orientation Unrestricted
Impact /Vibration resistance (m/s2 )(3) 300/50
Enclosure Dustproof
Note 1) Based on dynamic performance test, JIS B 8374-1981. (Coil temperature: 20°C, at
rated voltage, without surge suppressor)
Note 2) When operating the locking type manually, apply torque of 0.2 N·m or less.
Note 3) Impact resistance: No malfunction occurred when it is tested with a drop tester in the
axial direction and at the right angles to the main valve and
armature in both energized and de-energized states every once for
each condition. (Values at the initial period)
Vibration resistance: No malfunction occurred in a one-sweep test between 45 and 2000
Hz. Test was performed at both energized and de-energized states
in the axial direction and at the right angles to the main valve and
armature. (Values at the initial period)

Solenoid Specifications
Grommet (G)/(H), L plug connector (L),
Electrical entry
M plug connector (M), DIN terminal (D)
AC 50/60 Hz 100, 200, 24∗, 48∗, 110∗, 220∗
Coil rated voltage (V)
DC 24, 6∗, 12∗, 48∗
Allowable voltage fluctuation (%) –15 to +10% of rated voltage
Power consumption (W) (1) 1.8 (With indicator light 2.1)
[Current mA] DC
[24 VDC: 75 (With indicator light 87.5)]

Inrush 100 VAC: 45/50 Hz, 42/60 Hz

4.5/50 Hz, 4.2/60 Hz
Apparent power (VA) (1) 200 VAC: 22.5/50 Hz, 21/60 Hz
Refer to pages 3-3-74 to 3-3-84 for manifold use. AC
[Current mA] 100 VAC: 35/50 Hz, 30/60 Hz
Holding 3.5/50 Hz, 3/60 Hz
200 VAC: 17.5/50 Hz, 15/60 Hz
Surge voltage suppressor DC: Diode, AC: ZNR (2)
Made to Order Specifications Indicator light DC: LED (Red), AC: Neon bulb
(For details, refer to page 3-3-85.) Note 1) At rated voltage
Note 2) Plug-in should be ZNR

3-3-68
 5 Port Solenoid Valve
Base Mounted Series VZ5000
Flow Characteristics/Weight
Port size Flow characteristics (1)
Weight (g) (2)
Valve model Type of actuation 1, 5, 3 4, 2 1
4/2 (P
A/B) 4/2
5/3 (A/B
EA/EB)
(P, EA, EB) (A, B) C [dm3/(s·bar)] b Cv C [dm3/(s·bar)] b Cv Grommet
2 Single 200(120)
2.3 0.45 0.57 2.8 0.37 0.71
position Double 240(160)
VZ540--01 Closed center Rc 1/8 Rc 1/8 1.9 0.36 0.48 2.1 0.46 0.57
3
Exhaust center 1.2 0.48 0.35 3.4[1.3] 0.36[0.57] 0.86[0.41] 240(160)
position
Pressure center 3.3[0.85] 0.43[0.54] 0.78[0.25] 2.1 0.45 0.56
2 Single 200(120)
2.3 0.41 0.61 2.9 0.35 0.74
position Double 240(160) VK
VZ540--02 Closed center Rc 1/4 Rc 1/4 1.9 0.46 0.50 2.2 0.44 0.60
3
position Exhaust center 1.3 0.45 0.35 3.7[1.4] 0.27[0.56] 0.87[0.43] 240(160)
Pressure center 3.6[0.83] 0.23[0.55] 0.84[0.25] 2.1 0.47 0.58
VZ
Note 1) [ ]: Denotes the normal position. Exhaust center: 4/2
5/3, Pressure center: 1
4/2
Note 2) ( ): Without sub-plate. VF
VFR
Use as a guide for selection.
Cylinder Speed Chart Please confirm the actual conditions with SMC Sizing Program.
VP4
Bore size
Series CA1 Note) The CA1 series has been changed to the CA2 series.
VZS
Average
Series speed Pressure 0.5 MPa
(mm/s) Load factor 50% VFS
Stroke 500 mm
ø40 ø50 ø63 ø80 ø100 VS4
800 Perpendicular,
700 upward actuation
600 Horizontal actuation
VQ7
VZ514--02 500
(Piping: ø6 x 1 m) 400 EVS
300
200 VFN
100

Speed controller/Silencer AS3301F-02-06/AN200-2

800
Perpendicular,
700 upward actuation
600 Horizontal actuation
500
VZ514--02
400
(Piping: ø8 x 1 m)
300
200
100

Speed controller/Silencer AS3301F-02-08/AN200-2

800
Perpendicular,
700 upward actuation
600 Horizontal actuation
500
VZ514--02
400
(Piping: ø10 x 1 m)
300
200
100

Speed controller/Silencer AS3301F-02-10/AN200-2

800
Perpendicular,
700 upward actuation
600 Horizontal actuation
500
VZ514--02
400
(Piping: ø12 x 1 m)
300
200
100

Speed controller/Silencer AS4001F-02-12/AN200-2

∗ It is when the cylinder is extending that is meter-out controlled by speed controller which is directly connected with
cylinder, and its needle valve with being fully open.
∗ The average velocity of the cylinder is what the stroke is divided by the total stroke time.
∗ Load factor: ((Load weight x 9.8)/Theoretical force) x 100%

3-3-69
Series VZ5000
Construction
2 position single 2 position double

3 position closed center 3 position closed center/exhaust center/pressure center

3 position exhaust center

3 position pressure center

(This figure shows a closed center type.)

Component Parts Replacement Parts

No. Description Material Note No. Description Material Part no. Note
q Body Aluminum die-casted Platinum silver Aluminum DXT199-7-1∗P Rc 1 8
u Sub-plate
w Piston plate Resin Black die-casted DXT199-7-2∗P Rc 1 4
e Piston Aluminum, HNBR i Solenoid assembly Epoxy/Stainless steel DXT170-C-
r Spool valve Resin Common with
o O-ring NBR 13 x 11 x 1
t End cover Resin Black painted Series VZ 13 000
y Spool spring Stainless steel ∗ Thread type
Nil: Rc
F: G
N: NPT
T: NPTF

3-3-70
 5 Port Solenoid Valve
Base Mounted Series VZ5000
2 Position Single
VZ5140

Grommet (G), (H)

H- 02
VZ5140-G 01

VK
Manual override (Mounting hole)
(Non-locking) VZ
VF
VFR
VP4
(Lead wire length)

VZS
G: 300 mm
H: 600 mm

3-Rc 1/8, 1/4

(1(P), 4(A), 2(B) port) VFS
VS4
2-Rc 1/4
(5(R1), 3(R2) port) VQ7
EVS
(PE port)
VFN
(Lead wire length)

L plug connector (L) M plug connector (M)

VZ5140-L- 01
02 VZ5140-M- 01
02
≅300
≅300

(Lead wire length)

DIN terminal (D)

VZ5140-D- 01 02 MAX. 10
: With light/surge voltage suppressor
Applicable cable O.D.
ø3.5 to ø7

3-3-71
Series VZ5000
2 Position Double
VZ5240

Grommet (G), (H)

H - 02
VZ5240-G 01

Manual override
(Non-locking) (Mounting hole)
(Lead wire length)
G: 300 mm
H: 600 mm

(PE port)

3-Rc 1/8, 1/4

2-Rc 1/4
(1(P), 4(A), 2(B) port)
(5(R1), 3(R2) port)

L plug connector (L) M plug connector (M)

VZ5240-L- 01
02 VZ5240-M- 01
02
(Lead wire length)

≅300
≅300

(Lead wire length)

: With light/surge voltage suppressor

DIN terminal (D)
VZ5240-D- 01 02
MAX. 10 Applicable cable O.D.
ø3.5 to ø7

3-3-72
 5 Port Solenoid Valve
Base Mounted Series VZ5000
3 Position Closed Center/Exhaust Center/Pressure Center
VZ5340

Grommet (G), (H)

3
H-02
VZ5 45 40-G 01

(Lead wire length)

G: 300 mm
H: 600 mm

VZ5440
VK
VZ
Manual override (Mounting hole)
(Non-locking)
VF
VZ5540 VFR
VP4
VZS
VFS
VS4
VQ7
(PE port)
EVS
2-Rc 1/4
3-Rc 1/8, 1/4
(3(R1), 5(R2) port)
(1(P), 4(A), 2(B) port) VFN
L plug connector (L) M plug connector (M)
3 3
VZ5 4 40-L- 01
02 VZ5 4 40-M-01
02
5 5
(Lead wire length)

≅300
≅300

(Lead wire length)

DIN terminal (D)

3 : With light/surge voltage suppressor
VZ5 4 40-D- 01
02
5
MAX. 10

Applicable cable O.D.

ø3.5 to ø7

3-3-73
 Series VZ5000/Base Mounted
Manifold Specifications
Manifold Standard
Manifold Specifications
Model Type 40 Type 41 Type 42
Manifold type Single base/B mount
P(SUP), R(EXH) Common SUP and EXH
Valve stations 2 to 20
4(A), 2(B) port Position Base Base
porting specifications Direction Bottom Side
1(P), 3/5(R) port Rc 1/4
01(Rc 1/8)
C6 (One-touch fitting for ø6)
Port size
4(A), 2(B) port Rc 1/8 C8 (One-touch fitting for ø8)
B7 (One-touch fitting for 1/4")
C9 (One-touch fitting for 5/16")

Flow Characteristics
Port size Flow characteristics
Manifold 1(P), 5/3(R) 2(B), 4(A) 1
4/2 (P
A/B) 4/2
5/3 (A/B
R)
port port 3
C [dm /(s·bar)] b Cv C [dm3/(s·bar)] b Cv
VV5Z5-40 1/4 1/8 2.1 0.28 0.51 2.5 0.23 0.59
VV5Z5-41 1/4 1/8 2.0 0.30 0.50 2.2 0.30 0.55
VZ54
VV5Z5-42-C6 1/4 C6 1.5 0.32 0.38 2.2 0.23 0.52
VV5Z5-42-C8 1/4 C8 1.9 0.24 0.46 2.2 0.26 0.53
Note) Value at manifold base mounted, 2 position single operating

How to Order Manifold

Instruct by specifying the valves and blanking plate assembly to be mounted on the manifold along
with the manifold base model no.
(Example) VV5Z5-41-031-01····1 pc. (Manifold base)
∗VZ5140-5G············2 pcs. (Valve)
∗DXT199-22-1A······ 1 pc. (Blanking plate assembly)
The asterisk denotes the symbol for assembly. Prefix it to the part nos. of the solenoid valve, etc.

DIN Rail Manifold

Manifold Specifications
Model Type 45 Type 45F
Manifold type Stacking type non plug-in type Stacking type plug-in type
P(SUP), R(EXH) Common SUP and EXH
Valve stations 2 to 20
4(A), 2(B) port Position Base
Porting specifications Direction Side
1(P), 3/5(R) port C10 (One-touch fitting for ø10)
Port size C6 (One-touch fitting for ø6)
4(A), 2(B) port
C8 (One-touch fitting for ø8)
MIL-C-24308 Applicable for D-sub
Connector — JIS-X-5101 connector
Internal wiring — COM Note)
Note) It is available at +COM or –COM.

Flow Characteristics
Port size Flow characteristics
Manifold 1(P), 5/3(R) 2(B), 4(A) 1
4/2 (P
A/B) 4/2
5/3 (A/B
R)
port port 3
C [dm /(s·bar)] b Cv C [dm3/(s·bar)] b Cv
VV5Z5-45 C10 C6 1.5 0.31 0.38 2.2 0.17 0.52
VZ54
C10 C8 2.1 0.26 0.51 2.2 0.15 0.52
Note) Value at manifold base mounted, 2 position single operating

How to Order Manifold

Instruct by specifying the valves and blanking plate assembly to be mounted on the manifold along
with the manifold base model no.
(Example) VV5Z5-45FD-06-C8C····1 pc. (Manifold base)
∗VZ5143-5FZ················2 pcs. (Valve)
∗VZ5243-5FZ················3 pcs. (Valve)
∗VZ5000-65-1A·············1 pc. (Blanking plate assembly)
The asterisk denotes the symbol for assembly. Prefix it to the part nos. of the solenoid valve, etc.

3-3-74
 5 Port Solenoid Valve
Base Mounted Series VZ5000
Common SUP/Common EXH
Type 40 How to Order
1(P) port
Rc 1/4
VV5Z5 40 05 2 01
4(A), 2(B) P, R port
Stations Port size thread type
02 2 stations 01 Rc 1 8
Nil Rc

···
···
3/5(R) port F G
20 20 stations
Rc 1/4 N NPT
4(A), 2(B) port Note) For more than 10 stations, supply air to both
Rc 1/8 sides of 1(P) port and exhaust air from both
sides of 3 and 5(R) port.
T NPTF VK
Applicable solenoid
Type 41 How to Order valve VZ
G
VV5Z5 41 05 1 01 VZ54- LM
D VF
4(A), 2(B) P, R port Applicable blanking plate
Stations Port size thread type assembly
1(P) port
02 2 stations 01 Rc 1 8 Nil Rc DXT199-22-1A
VFR
Rc 1/4

···
···
F G Applicable individual EXH
4(A), 2(B) port 20 20 stations N NPT spacer assembly VP4
Rc 1/8 3/5(R) port Note) For more than 8 stations, supply air to both sides of T NPTF DXT199-29-2A
P port and exhaust air from both sides of R port. Applicable individual SUP
Rc 1/4
spacer assembly
VZS
DXT199-35-1A
Type 42 How to Order
Applicable interface VFS
VV5Z5 42 05 1 C6 regulator
ARBZ5000-00-P
P, R port
VS4
Stations A, B port size
thread type
1(P) port
02 2 stations C6 One-touch fitting for ø6
Nil Rc
VQ7
C8
···
···

One-touch fitting for ø8

Rc 1/4 F G
20 20 stations B7 One-touch fitting for 1/4"
4(A), 2(B) port B9 One-touch fitting for 5/16" N NPT EVS
C6, C8 3/5(R) port T NPTF
Rc 1/4 VFN
Note) For more than 8 stations, supply air to both sides of 1(P) port
and exhaust air from both sides of 3 and 5(R) port.

DIN Rail Manifold

Common SUP/Common EXH
Type 45 (Non plug-in type) How to Order Applicable solenoid
valve
VV5Z5 45 05 D C8 C VZ54- LM
G

Stations
SUP/EXH block 4 (A), 2 (B) D
02 2 stations port size Applicable blanking plate
mounting position
···
···

assembly
Symbol Position Applicable stations One-touch
20 20 stations C6 VZ5000-65-2A
U U side 2 to 10 stations fitting for ø6
D D side 2 to 10 stations One-touch DIN rail length specified
C8
B Both sides 2 to 20 stations fitting for ø8 Nil Standard length
Special Special Mixed M∗ 3 For 3 stations (Specify a longer
M∗ specifications ∗ In the case of mixed
specifications
···
···

rail than the

∗ For special specifications, specifications (M), indicate 20 For 20 stations standard length.)
indicate separately by the separately on the manifold
manifold specification sheet. specification sheet.

Type 45F (Plug-in type) How to Order Applicable solenoid

valve
VV5Z5 45F D 05 C8 C VZ543-FZ
Applicable blanking plate
assembly
Connector mounting direction 4(A), 2(B) VZ5000-65-1A
Symbol Mounting direction Applicable stations port size
U U side
2 to 10 stations One-touch DIN rail length specified
D D side C6
fitting for ø6 Nil Standard length
B Both sides 11 to 10 stations One-touch 3 For 3 stations (Specify a longer
C8
Stations rail than the
···
···

fitting for ø8
02 2 stations
SUP/EXH block mounting position M∗ 20 For 20 stations standard length.)
Mixed
For 2 to 10 stations : One side ∗ In the case of mixed specifications
···
···

20 20 stations Nil (Same as direction of connector mount) (M), indicate separately on the
For 11 to 20 stations: Both sides manifold specification sheet.
B For 2 to 10 stations: Both sides
M∗ Special specifications
∗ For special specifications, indicate
separately by the manifold specification
sheet.

3-3-75
Series VZ5000
Option/Standard Manifold

Combinations of Solenoid Individual EXH Spacer Assembly Installation of the VZ500 Valve
Valve, Manifold Gasket and DXT199-29-2A on the VZ5000 Manifold
Manifold Base • Use of an adaptor plate makes it possible
Round head Round head to mount Series VZ500 on the manifold
combination screw combination screw base of Series VZ5000.
• The mounting direction is shown in the
(With springM3washer
x 31
) (M3
With spring washer )
x 47 diagram below. Mount the solenoid so that
it will be on the same side as the single
solenoid of the Series VZ5000.
• In the case of base mounting, 2(A) port of
3 port valve should be 2(B) port of manifold
base.

Adapter Plate Assembly

DXT201-3-2A
Round head
combination screw
Gasket Series VZ500
(M3 x 38
With spring washer ) Base mounted
Round head
Individual combination screw
Applicable base EXH spacer DXT199-23-1
VV5Z5-40
VV5Z5-41 (M3 x 31
With spring washer )
VV5Z5-42 2-Rc 1/8 Gasket
(EXH port)
Blanking Plate Assembly
DXT199-22-1A Applicable base
Round head VV5Z5-40
combination screw VV5Z5-41
VV5Z5-42
(With spring M3
washer )
x8

Blanking plate
Round head
Gasket
Interface Regulator combination
(P port regulation) screw

Interface style regulators can be placed on

top of the manifold base to reduce the (M3
With spring washer )
x 10

Applicable base pressure of each of the valves.

Adapter plate
VV5Z5-40
VV5Z5-41 ARBZ5000-00-P
VV5Z5-42
Gasket
Individual SUP Spacer Assembly Round head
combination screw
DXT199-35-1A
( With spring
washer )
Round head Applicable base
combination screw VV5Z5-40
VV5Z5-41
(M3
With spring washer)
x 47 VV5Z5-42

Gasket

Individual
SUP spacer Before Applicable base
using, refer VV5Z5-40
Gasket to page VV5Z5-41
3-3-8. VV5Z5-42
Rc 1/8 Caution
(SUP port) Mounting Screw Tightening Torques
Applicable base M3: 0.8 N·m
VV5Z5-40
VV5Z5-41
VV5Z5-42

3-3-76
 5 Port Solenoid Valve
Base Mounted Series VZ5000
Option/DIN Rail Manifold
Blanking Plate Assembly Combination of Solenoid Valve, Gasket and Manifold Base
VZ5000-65-2A
Round head
Round head combination screw
Round head combination screw combination screw

( With springM3washer
x 31
) ( With springM3washer
x 31
)
( With spring washer
M3 x 8
)
Blanking plate VK
VZ
Manifold gasket
VF
Manifold gasket Manifold gasket
VFR
Applicable base
VV5Z5-45 Applicable base
VP4
Applicable base
VV5Z3-45
VV5Z5-45F
VZS
VFS
VZ5000-65-1A SUP Block Disk EXH Block Disk
Round head By installing a SUP block disk in the By installing an EXH block disk in the VS4
combination screw pressure supply passage of a manifold exhaust passage of a manifold valve, it is
valve, it is possible to supply two or more possible to divide the valve’s exhaust so that
VQ7
(With spring washer
M3 x 8
) different high and low pressures to one
manifold.
it does not affect another valve.

Blanking plate
VZ5000-68-1A VZ5000-68-1A EVS
VFN
Manifold gasket

Applicable Plug Assembly (D-sub connector cable assembly)

Cable length Assembly part no. Component parts
Dust cap 1.5 m VVZS3000-21A-1
Plug MIL standard D-sub connector
3m VVZS3000-21A-2
Number of terminals: 25
5m VVZS3000-21A-3 Cable: 25 cores x 0.3 mm2
8m VVZS3000-21A-4
For details, refer to page 3-3-8.

Applicable base
VV5Z5-45F

Caution
Mounting Screw Tightening Torques
M2.5: 0.32 N·m
(For stacking type manifold)

3-3-77
Series VZ5000
Exploded View/DIN Rail Manifold
Type 45 Manifold r

U side q

(a) Bolt (Both sides)

(b) Lever D side

(a) Bolt (Both sides)

Replacement Parts
No. Description Part no. Note
Manifold block C6: A, B port with One-touch fitting for ø6
q VZ5000-50A-2-C6
C8
assembly C8: A, B port with One-touch fitting for ø8
w SUP/EXH block assembly VZ5000-51A-2 P/R port with One-touch fitting for ø10 DIN rail
e End block assembly VZ5000-52A-2D For D side
r End block assembly VZ5000-52A-2U For U side

How to Increase Manifold Base Station expansion is possible at any position.

(1) Loosen (both) bolts (a), which are securing the manifold onto the
DIN rail, 1 to 2 turns.
(To remove the manifold base from the DIN rail, loosen the bolts 4
Fig. (1)
to 5 turns.)

(2) Press lever (b) to disconnect the manifold block assembly at the
location in which you wish to place an additional manifold block
assembly. (However, there are no levers between q and r or (a) Bolt (Both sides)
between e and r. They can be disconnected by merely pulling
them apart.)

(3) Mount additional manifold block assembly on the DIN rail as

shown in the Fig. (2).
Fig. (2)
(4) Press the block assemblies and tighten the bolts (a) to fix them to
the DIN rail.

Note) When there are 10 or fewer manifold block assemblies,

and more are added to make a total of 11 or more, a Hook this part onto
supply/exhaust block assembly must also be added. the DIN rail, and press
down in the direction
of the arrow.

(b) Lever

3-3-78
 5 Port Solenoid Valve
Base Mounted Series VZ5000
Exploded View/DIN Rail Manifold
Type 45F Manifold u

e i

t
VK
U side
q VZ
(b)
Lever
y VF
VFR

w
VP4
Location of addition
(a)
Bolt VZS
r (Both sides)
VFS
Replacement Parts (b) Lever
No. Description Part no. Note VS4
Manifold block C6 C6: A, B port with One-touch fitting for ø6
q VZ5000-50A-1- C8
assembly C8: A, B port with One-touch fitting for ø8 (a)
Bolt (Both sides)
VQ7
SUP/EXH block For D side, With D-sub connector and
w VZ5000-51A-1D
assembly P/R port with One-touch fitting for ø10 D side EVS
SUP/EXH block For U side, With D-sub connector and DIN rail
e VZ5000-51A-1U
assembly P/R port with One-touch fitting for ø10
r End block assembly VZ5000-52A-2D For D side, set with w
VFN
t End block assembly VZ5000-52A-1U For U side
y End block assembly VZ5000-52A-1D For D side
u End block assembly VZ5000-52A-2U For U side, set with e
SUP/EXH block Without D-sub connector, For indicated location
i VZ5000-51A-1M
assembly P/R port with One-touch fitting for ø10

To add a manifold block assembly, add it to the U side so that the terminal number of the
How to Increase Manifold Base D-sub connector and the valve link position will be in accordance with the circuit diagram.

(1) Loosen (both) bolts (a), which are securing the manifold onto the Housing cover
DIN rail, 1 to 2 turns. (To remove the manifold base from the DIN
rail, loosen the bolts 4 to 5 turns.) Hook this part on
to the DIN rail
and press down
until a click is
heard.
(2) Using a flat screwdriver, press lever (b) to disengage the link of Fig. (1)
the manifold block assembly on the U side or the D side from the
SUP/EXH block assembly or from the end block assembly. Lead
Fig. (2) Terminal wire
no.
(However, there are no levers between t and q. They can be color
(b) Lever B side coil
Black
disconnected by merely pulling them apart.) Connector 1 station A side coil
D-sub terminal no. (11 stations) White
Black connector B side coil
Black
(3) Remove the housing cover from the D-sub connector portion of White
2 station A side coil
(12 stations) White
the SUP/EXH block assembly. (Refer to Fig. (1).) B side coil
3 station Black
A side coil
(13 stations) White
(4) Following the procedure shown in Fig. (2), mount the manifold block B side coil
4 station Black
assembly to be added onto the DIN rail. As shown in Fig. (3), insert (14 stations)
A side coil
White
the pin of the lead wire assembly into the D-sub connector, and 5 station
B side coil
Black
Lead A side coil
attach the round crimped terminal to the screw that connects the wire (15 stations) White
wires. ass'y B side coil
Black
Hook 6 station A side coil
Pin (16 stations) White
B side coil
(5) Press the block assemblies and tighten the bolts (a) to fix them to After inserting the pin, U side 7 station Black
A side coil
the DIN rail. lightly pull on the lead (17 stations) White
B side coil
wire to verify the lock. 8 station Black
A side coil
Note) When there are 10 or fewer manifold block assemblies, (18 stations) White
and more are added to make a total of 11 or more, a Fig. (3) How to insert lead 9 station
B side coil
Black
A side coil
supply/exhaust block assembly must also be added. wire assembly pin Stations (19 stations) White
Housing side D side B side coil
10 station Black
A side coil
(20 stations) White
Red
Red

3-3-79
Series VZ5000
Type 40 Manifold: Bottom Ported
VV5Z5-40- Station 2-01

Grommet (G), (H) (Mounting hole)

6-Rc 1/4
(1(P), 3/5(R) port)

Manual override G: 300 mm

(Non-locking) H: 600 mm
(Lead wire length)

PE port
(Pilot EXH)
2n-Rc 1/8
(4(A), 2(B) port)

(Pitch)

(mm)
Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
L1 66 85 104 123 142 161 180 199 218 237 256 275 294 313 332 351 370 389 408
L2 46 65 84 103 122 141 160 179 198 217 236 255 274 293 312 331 350 369 388

L plug connector (L) M plug connector (M) DIN terminal (D)

Applicable cable O.D.
ø3.5 to ø7
(Lead wire length)

MAX. 10
≅300

≅300

(Lead wire length)

: With light /surge voltage suppressor

3-3-80
 5 Port Solenoid Valve
Base Mounted Series VZ5000
Type 41 Manifold: Side Ported
VV5Z5-41- Station 1-01
Manual override PE port
(Non-locking)
(Pilot EXH)
Grommet (G), (H)
6-Rc 1/4
(1(P), 3/5(R) port)
VK
VZ
VF

(Mounting hole) VFR

VP4
(Pitch)
G: 300 mm
H: 600 mm VZS
(Lead wire length)
VFS
VS4
VQ7
EVS
VFN
2n-Rc 1/8
(4(A), 2(B) port)
(mm)
Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
L1 78 98 118 138 158 178 198 218 238 258 278 298 318 338 358 378 398 418 438
L2 50 70 90 110 130 150 170 190 210 230 250 270 290 310 330 350 370 390 410

L plug connector (L) M plug connector (M) DIN terminal (D)

(Lead wire length)

≅300
≅300

MAX. 10

(Lead wire length)

Applicable cable O.D.
ø3.5 to ø7

: With light/surge voltage suppressor

3-3-81
Series VZ5000
Type 42 Manifold: Side Ported
VV5Z5-42- Station 1- C6
C8
Manual override
(Non-locking)
PE port
Grommet (G), (H) (Pilot EXH)

6-Rc 1/4
(1(P), 3/5(R) port)

(Pitch)

C8: MAX. 6.5

C6: MAX. 6
(Mounting hole) G: 300 mm
H: 600 mm
2n-One-touch fitting (Lead wire length)
(4(A), 2(B) port)
Applicable tubing model
C6: T0604
C8: T0806

(mm)
Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
L1 77 96 115 134 153 172 191 210 229 248 267 286 305 324 343 362 381 400 419
L2 49 68 87 106 125 144 163 182 201 220 239 258 277 296 315 334 353 372 391

L plug connector (L) M plug connector (M) DIN terminal (D)

(Lead wire length)

≅300
≅300

MAX. 10

(Lead wire length)

Applicable cable O.D.

ø3.5 to ø7

: With light/surge voltage suppressor

3-3-82
 5 Port Solenoid Valve
Base Mounted Series VZ5000
Type 45 DIN Rail Manifold (Non Plug-in): Side Ported

VV5Z5-45- Station D- C6C

C8C
Grommet (G), (H) C6C
VV5Z5-45- Station B-
C8C
2n-One-touch fitting (Pitch)
(A, B port) Applicable
tubing model (Pitch)
C6: T0604
C8: T0806 VK
VZ
VF
One-touch fitting
(P, R port) Applicable tubing model VFR
VP4
VZS
VFS
U side D side
VS4
DIN rail VQ7
(mm)

DIN rail
Manual
override G: 300 Stations 2 3 4 5 6 7 8 9 10 EVS
(Non- H: 600 L1 148 160.5 185.5 198 223 235.5 260.5 273 298
holding screw locking) (Lead wire length)
(Rail mounting hole pitch 12.5)
L2 137.5 150 175 187.5 212.5 225 250 262.5 287.5 VFN
L3 116 135 154 173 192 211 230 249 268
L4 16 13 16 12.5 15.5 12.5 15.5 12 15 (mm)

(Station n)······················(Station 1) Stations 11 12 13 14 15 16 17 18 19 20

L1 310.5 335.5 348 373 385.5 410.5 423 448 473 485.5
L2 300 325 337.5 362.5 375 400 412.5 437.5 462.5 475
L3 287 306 325 344 363 382 401 420 439 458
L4 12 15 11.5 14.5 11.5 14.5 11 14 17 14

VV5Z5-45- Station U- C4C

C6C
(Pitch)
Separation
lever
(mm)
Stations 2 3 4 5 6 7 8 9 10
L1 123 148 160.5 185.5 198 223 235.5 260.5 273
L2 112.5 137.5 150 175 187.5 212.5 225 250 262.5
L3 97 116 135 154 173 192 211 230 249
L4 13 16 13 16 12.5 15.5 12.5 15.5 12

L plug connector (L) M plug connector (M) DIN terminal (D)

(Lead wire length)

MAX. 10
≅300

≅300
(Lead wire length)

(mm)
Stations 2 3 4 5 6 7 8 9 10
L1 123 148 160.5 185.5 198 223 235.5 260.5 273
Applicable cable O.D. ø3.5 to ø7 L2 112.5 137.5 150 175 187.5 212.5 225 250 262.5
L3 97 116 135 154 173 192 211 230 249
L4 13 16 13 16 12.5 15.5 12.5 15.5 12

3-3-83
Series VZ5000
Type 45F DIN Rail Manifold (Plug-in): Side Ported

VV5Z5-45FD- Station - C6C

C8C
2n-One-touch fitting
(A, B port)
Applicable tubing
model (Pitch)
C6: T0604
C8: T0806

One-touch fitting port (P, R port)

Applicable tubing model: T1075

U side D side

DIN rail
DIN rail
holding screw
Manual override Terminal no. 1
(Non-locking) {JIS-X-5101
∗Applicable connector D-SUB MIL-C-24308 }
(Rail mounting hole pitch 12.5)
D side (mm)
(Station n)············(Station 1) connector Stations 2 3 4 5 6 7 8 9 10
L1 123 148 160.5 185.5 198 223 235.5 260.5 273
L2 112.5 137.5 150 175 187.5 212.5 225 250 262.5
L3 97 116 135 154 173 192 211 230 249
L4 13 16 13 16 12.5 15.5 12.5 15.5 12
C6C
Separation
VV5Z5-45FU
D- Station B- C8C (2 to 10 stations)
lever
(Push type) C6C
VV5Z5-45FB- Station - C8C (11 to 20 stations)
VV5Z5-45FU- Station - C6C
C8C (Pitch) (Pitch)

(mm) (mm)
Stations 2 3 4 5 6 7 8 9 10 Stations 2 3 4 5 6 7 8 9 10
L1 123 148 160.5 185.5 198 223 235.5 260.5 273 L1 148 160.5 185.5 198 223 235.5 260.5 273 298
L2 112.5 137.5 150 175 187.5 212.5 225 250 262.5 L2 137.5 150 175 187.5 212.5 225 250 262.5 287.5
L3 97 116 135 154 173 192 211 230 249 L3 116 135 154 173 192 211 230 249 268
L4 13 16 13 16 12.5 15.5 12.5 15.5 12 L4 16 13 16 12.5 15.5 12.5 15.5 12 15 (mm)
Stations 11 12 13 14 15 16 17 18 19 20
L1 310.5 335.5 348 373 385.5 410.5 423 448 473 485.5
L2 300 325 337.5 362.5 375 400 412.5 437.5 462.5 475
L3 287 306 325 344 363 382 401 420 439 458
L4 12 15 11.5 14.5 11.5 14.5 11 14 17 14

3-3-84
 Series VZ
Made to Order Specifications:
Please contact SMC for detailed specifications, dimensions, and delivery.

1. Solenoid Valve: External Pilot Specifications

Applicable solenoid valve series
VZ3000/5000
(Non plug-in type only)
VK
Model no.
VZ
VZ 35 0 ( ) X20 VF
VFR
Entry is the same as standard products.
VP4
VZS
Specifications
Operating pressure Main pressure –100 kPa to 0.7 VFS
range (MPa) External pilot pressure 0.15 to 0.7
Pilot exhaust method Pilot valve individual exhaust VS4
Dimensions VQ7
VZ3000: 8 mm longer
VZ5000: 8 mm longer
EVS
JIS Symbol VFN
Body ported
2 position single 3 position closed center

2 position double 3 position exhaust center

3 position pressure center

3-3-85