PROCESS INDICATOR ENVIRONMENT CONDITION:

PI 41
Operating Temp. 0°C to 55°C
UP to 95% RH
Relative Humidity
(non-condensing)

Protection Level IP-65 (Front side) As per IS/IEC

(As per request) 60529 : 2001

MECHANICAL INSTALLATION

Panel Cutout
Outline Dimension (mm)
Dimension (mm)

PI 41
3
46

TECHNICAL SPECIFICATION 9500 45

48
FEATURES: SET

Elegant appearance and compact in size 45

48
Accurate and sturdy in operation
Very easy to operate TERMINAL CONNECTION

INPUT SPECIFICATION: 0-10V

100 ~ 270V AC 0/4-20
Voltage: 0 to 10V DC mA DC DC
Input Types
L N + - +
Current: 0 to 20mA DC,
4 to 20mA DC 1 2 3 4 5
I/P Filter Time 0.1 Sec to 10.0 Sec
Resolution Decimal point selectable:
0.1, 0.01, 0.001, 0001
Connection for voltage I/P
Range -999 to 9999 (For all I/P)
Indication ±1% FSD ± 1 digit (0-10V DC)
Accuracy
+
(FSD - Full Scale Deflection)

4 5
DISPLAY AND KEY:
Display 4 digit, 7 segment, 0.39” LED
Keys SET, SHIFT, INC
Connection for current I/P
DIMENSION:
(4-20mA DC or
Size 48 (H) x 48 (W) x 46 (D) mm 0-20mA DC)
Panel Cutout 45 (H) x 45(W) mm +

POWER SUPPLY: 3 4
Supply
Voltage 100 to 270V AC, 50-60Hz
Power
2VA @ 230V AC MAX
Consuption
(VA Rating)

Page -1
 KEY OPERATION MAINTENANCE

1. The equipment should be cleaned regularly to avoid

FUNCTION PRESS KEY blockage of ventilating parts.
OPERATOR MODE 2. Clean the equipment with a clean soft cloth. Do not use
To enter in parameter setting + isopropyl alcohol or any other cleaning agent.
For 5 sec 3. Fusible resistor must not be replaced by operator.
To go in factory setting mode +
For 3 sec
! SAFETY PRECAUTION
PARAMETER SETTING MODE
Edited parameter value to be set, All safety related codifications, symbols and instructions
And move to the next step. (Single click operation) that appear in this operating manual or on the equipment
must be strictly followed to ensure the safety of the operating
It will select the digit to modify, personnel as well as the instrument.
When value is edited If all the equipment is not handled in a manner specified
by the manufacturer, it might impair the protection provided
It will change the value of by the equipment.
selected digit. Read complete instructions prior to installation
and operation of the unit.
Set parameter to be save & exit.
For 3 sec WARNING : Risk of electric shock.

INSTALLATION GUIDELINES WARNING GUIDELINES

1. This equipment, being built-in-type, normally becomes a WARNING : Risk of electric shock.
part of main control panel and in such case the terminals
do not remain accessible to the end user after installation 1. To prevent the risk of electric shock power supply to the
and internal wiring. equipment must be kept OFF while doing the wiring
arrangement. Do not touch the terminals while power is
2. Do not allow pieces of metal, wire clippings, or fine
being supplied.
metallic fillings from installation to enter the product or
else it may lead to a safety hazard that may in turn 2. To reduce electro magnetic interference, use wire with
endanger life or cause electrical shock to the operator. adequate rating and twists of the same of equal size shall
be made with shortest connection.
3. Circuit breaker or mains switch must be installed
3. Cable used for connection to power source, must have a
between power source and supply terminal to facilitate
cross section of 1mm or greater. These wires should have
power ‘ON’ or ‘OFF’ function. However this mains switch
insulations capacity made of at least 1.5kV.
or circuit breaker must be installed at convenient place
normally accessible to the operator. 4. A better anti-noise effect can be expected by using
standard power supply cable for the instrument.
4. Use and store the instrument within the specified ambient
temperature and humidity ranges as mentioned in this
manual.

MECHANICAL INSTALLATION GUIDELINES ERROR DISPLAY

1. Prepare the panel cutout with proper dimensions as show When an error has occurred the display indicates error codes
above. as given below.
2. Fit the unit into the panel with the help of clamp given. ERROR MEANING
[Link] equipment in its installed state must not come in close Over range Input applied
proximity to any heating source, caustic vapors, oils steam,
or other unwanted process by products. OUER 1) For 0 to 10V DC - exceed
10 V DC
4. Use the specified size of crimp terminal (M3.5 screws) to 2) For 0/4-20mA dc - exceed
wire the terminal block. Tightening the screws on the 20mA DC
terminal block using the tightening torque of the range of
When I/P is 4 to 20mA DC
1.2 N.m.
5. Do not connect anything to unused terminals. LOv is selected, And if applied I/P
signal is lower than selected
signal low level (SLL) than this
message will display.
Page -2
 PARAMETER SETTING

Press SET key

1 2 3 4 Process value
s L L Signal low level
Press SET + key for 5 Sec
only for 4-20mA
Press SET key
p a r a Parameter message
a 3 5 Press & key to set
Press SET key offset value

I n p Input
Press SET key for 3 sec to save & exit
Press SET key

0 - 1 0 4 - 2 0 0 - 2 0 Press key
FACTORY SETTING
Press SET key

D P Decimal Point
1 2 3 4
Press SET key
Press SET + key for 3 Sec
0 0 0 0 Press key to set the position
of DP F C S T
Press SET key
Press SET key
L R N Low Range
0 - 1 0 4 - 2 0 0 - 2 0
Press SET key
Press key
0 0 0 0 Press & key to set
low range value Press SET key for 3 sec to save & exit
Press SET key

H R N High Range

Press SET key

FACTORY SETTING
1 0 0 0 Press & key to set Parameter 0-10V DC 0-20mA DC 4-20mA DC
high range value Low Range 0 0 0
Press SET key High Range 1000 2000 2000
Decimal Point 0000. 0000. 0000.
F L t r Filter Time Filter Time 0.5 sec 0.5 sec 0.5 sec
OffSet 0 0 0
Press SET key
Correction factor 0 0 0
0 0 5 Press & key to set Signal Low Level - - 3.5mA
filter time value
Press SET key
PARAMETER RANGE
O F S T Offset
Press SET key Sr. Parameter Range
1 Low Range -999 to 9999
0 0 0 0 Press & key to set
offset value 2 High Range -999 to 9999
Press SET key
3 Filter Time 00.1 to 10.0 sec
C R F C Correction factor 4 Off set -999 to 999

Press SET key 5 Correction factor -999 to 999

6 Signal Low Level 0.0 to 5.0mA
0 0 0 0 Press & key to set
offset value

To be continued
Specifications are subject to change, since development is a continuous process,
So for more updated operating information and Support,
Please contact our Helpline: 9978991474/76/82 or
Email at service@[Link] Ver:201031

Page -3