Introduction to

CMOS VLSI
Design

Lecture 20:
Package, Power, and I/O
David Harris

Harvey Mudd College

Spring 2004
 Outline
 Packaging
 Power Distribution
 I/O
 Synchronization

20: Package, Power, and I/O CMOS VLSI Design Slide 2

 Packages
 Package functions
– Electrical connection of signals and power from
chip to board
– Little delay or distortion
– Mechanical connection of chip to board
– Removes heat produced on chip
– Protects chip from mechanical damage
– Compatible with thermal expansion
– Inexpensive to manufacture and test

20: Package, Power, and I/O CMOS VLSI Design Slide 3

 Package Types
 Through-hole vs. surface mount

20: Package, Power, and I/O CMOS VLSI Design Slide 4

 Multichip Modules
 Pentium Pro MCM
– Fast connection of CPU to cache
– Expensive, requires known good dice

20: Package, Power, and I/O CMOS VLSI Design Slide 5

Chip-to-Package Bonding
 Traditionally, chip is surrounded by pad frame
– Metal pads on 100 – 200 mm pitch
– Gold bond wires attach pads to package
– Lead frame distributes signals in package
– Metal heat spreader helps with cooling

20: Package, Power, and I/O CMOS VLSI Design Slide 6

 Advanced Packages
 Bond wires contribute parasitic inductance
 Fancy packages have many signal, power layers
– Like tiny printed circuit boards
 Flip-chip places connections across surface of die
rather than around periphery
– Top level metal pads covered with solder balls
– Chip flips upside down
– Carefully aligned to package (done blind!)
– Heated to melt balls
– Also called C4 (Controlled Collapse Chip Connection)

20: Package, Power, and I/O CMOS VLSI Design Slide 7

 Package Parasitics
 Use many VDD, GND in parallel
– Inductance, IDD
Package

Chip Bond Wire Lead Frame Board

VDD VDD
Signal Pins

Signal Pads

Chip Package
Capacitor
Chip Board
GND GND

20: Package, Power, and I/O CMOS VLSI Design Slide 8

 Heat Dissipation
 60 W light bulb has surface area of 120 cm2
 Itanium 2 die dissipates 130 W over 4 cm2
– Chips have enormous power densities
– Cooling is a serious challenge
 Package spreads heat to larger surface area
– Heat sinks may increase surface area further
– Fans increase airflow rate over surface area
– Liquid cooling used in extreme cases ($$$)

20: Package, Power, and I/O CMOS VLSI Design Slide 9

 Thermal Resistance
 DT = qjaP
– DT: temperature rise on chip
– qja: thermal resistance of chip junction to ambient
– P: power dissipation on chip
 Thermal resistances combine like resistors
– Series and parallel
 qja = qjp + qpa
– Series combination

20: Package, Power, and I/O CMOS VLSI Design Slide 10

 Example
 Your chip has a heat sink with a thermal resistance
to the package of 4.0° C/W.
 The resistance from chip to package is 1° C/W.
 The system box ambient temperature may reach
55° C.
 The chip temperature must not exceed 100° C.
 What is the maximum chip power dissipation?

20: Package, Power, and I/O CMOS VLSI Design Slide 11

 Example
 Your chip has a heat sink with a thermal resistance
to the package of 4.0° C/W.
 The resistance from chip to package is 1° C/W.
 The system box ambient temperature may reach
55° C.
 The chip temperature must not exceed 100° C.
 What is the maximum chip power dissipation?

 (100-55 C) / (4 + 1 C/W) = 9 W

20: Package, Power, and I/O CMOS VLSI Design Slide 12

 Power Distribution
 Power Distribution Network functions
– Carry current from pads to transistors on chip
– Maintain stable voltage with low noise
– Provide average and peak power demands
– Provide current return paths for signals
– Avoid electromigration & self-heating wearout
– Consume little chip area and wire
– Easy to lay out

20: Package, Power, and I/O CMOS VLSI Design Slide 13

 Power Requirements
 VDD = VDDnominal – Vdroop
 Want Vdroop < +/- 10% of VDD
 Sources of Vdroop
– IR drops
– L di/dt noise
 IDD changes on many time scales
Power

Max
clock gating

Average

Min

Time

20: Package, Power, and I/O CMOS VLSI Design Slide 14

 Power System Model
 Power comes from regulator on system board
– Board and package add parasitic R and L
– Bypass capacitors help stabilize supply voltage
– But capacitors also have parasitic R and L
 Simulate system for time and frequency responses
Voltage Printed Circuit Package Solder Chip
Regulator Board Planes and Pins Bumps

Bulk Ceramic Package On-Chip On-Chip

VDD
Capacitor Capacitor Capacitor Capacitor Current Demand

Board Package

20: Package, Power, and I/O CMOS VLSI Design Slide 15

 Bypass Capacitors
 Need low supply impedance at all frequencies
 Ideal capacitors have impedance decreasing with w
 Real capacitors have parasitic R and L
– Leads to resonant frequency of capacitor
2
10

1
10
0.03 
impedance

1 mF 10
0

0.25 nH
-1
10

-2
10
4 5 6 7 8 9 10
10 10 10 10 10 10 10
frequency (Hz)

20: Package, Power, and I/O CMOS VLSI Design Slide 16

 Frequency Response
 Use multiple capacitors in parallel
– Large capacitor near regulator has low impedance
at low frequencies
– But also has a low self-resonant frequency
– Small capacitors near chip and on chip have low
impedance at high frequencies
 Choose caps to get low impedance at all frequencies
impedance

frequency (Hz)

20: Package, Power, and I/O CMOS VLSI Design Slide 17

 Input / Output
 Input/Output System functions
– Communicate between chip and external world
– Drive large capacitance off chip
– Operate at compatible voltage levels
– Provide adequate bandwidth
– Limit slew rates to control di/dt noise
– Protect chip against electrostatic discharge
– Use small number of pins (low cost)

20: Package, Power, and I/O CMOS VLSI Design Slide 18

 I/O Pad Design
 Pad types
– VDD / GND
– Output
– Input
– Bidirectional
– Analog

20: Package, Power, and I/O CMOS VLSI Design Slide 19

 Output Pads
 Drive large off-chip loads (2 – 50 pF)
– With suitable rise/fall times
– Requires chain of successively larger buffers
 Guard rings to protect against latchup
– Noise below GND injects charge into substrate
– Large nMOS output transistor
– p+ inner guard ring
– n+ outer guard ring
• In n-well

20: Package, Power, and I/O CMOS VLSI Design Slide 20

 Input Pads
 Level conversion VDDH VDDL

– Higher or lower off-chip V A

VDDL Y A Y

– May need thick oxide gates

weak

 Noise filtering A Y
Y
– Schmitt trigger weak

– Hysteresis changes VIH, VIL A

 Protection against electrostatic discharge

20: Package, Power, and I/O CMOS VLSI Design Slide 21

 ESD Protection
 Static electricity builds up on your body
– Shock delivered to a chip can fry thin gates
– Must dissipate this energy in protection circuits
before it reaches the gates Diode
clamps
 ESD protection circuits R
PAD
– Current limiting resistor Current Thin
gate
– Diode clamps
limiting
resistor oxides

 ESD testing
1500 
– Human body model Device
Under
100 pF
– Views human as charged capacitor Test

20: Package, Power, and I/O CMOS VLSI Design Slide 22

 Bidirectional Pads
 Combine input and output pad
 Need tristate driver on output
– Use enable signal to set direction
– Optimized tristate avoids huge series transistors
PAD

En
Din
Dout

NAND

Dout

En Y

Dout
NOR

20: Package, Power, and I/O CMOS VLSI Design Slide 23

 Analog Pads
 Pass analog voltages directly in or out of chip
– No buffering
– Protection circuits must not distort voltages

20: Package, Power, and I/O CMOS VLSI Design Slide 24

 MOSIS I/O Pad
 1.6 mm two-metal process
– Protection resistors
– Protection diodes
– Guard rings
– Field oxide clamps

PAD
600/3
264  185 
Out
240 48 90
En In
160 20 40
Out
In_unbuffered In_b

20: Package, Power, and I/O CMOS VLSI Design Slide 25