Chapter 3
Resistance
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
OBJECTIVES
• Become familiar with the parameters that
determine the resistance of an element and
be able to calculate the resistance from the
given dimensions and material
characteristics.
• Understand the effects of temperature on
the resistance of a material and how to
calculate the change in resistance with
temperature.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
OBJECTIVES
• Become familiar with the broad range of
commercially available resistors available
today and how to read the value of each
from the color code or labeling.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
INTRODUCTION
• This opposition to the flow of charge
through an electrical circuit, called
resistance, has the units of ohms
and uses the Greek letter omega (Ω)
as its symbol.
• The graphic symbol for resistance,
which resembles the cutting edge of a
saw.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
INTRODUCTION
FIG. 3.1 Resistance symbol and notation.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
INTRODUCTION
• This opposition, due primarily to collisions
and friction between the free electrons and
other electrons, ions, and atoms in the path
of motion, converts the supplied electrical
energy into heat that raises the
temperature of the electrical component
and surrounding medium.
• The heat you feel from an electrical heater
is simply due to current passing through a
high-resistance material.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
RESISTANCE
• The resistance of any material is due
primarily to four factors:
– Material
– Length
– Cross-sectional area
– Temperature of the material
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
RESISTANCE
• The atomic structure determines how easily a free
electron will pass through a material.
• The longer the path through which the free
electron must pass, the greater is the resistance
factor.
• Free electrons pass more easily through
conductors with larger crosssectional areas.
– In addition, the higher the temperature of the conductive
materials, the greater is the internal vibration and motion
of the components that make up the atomic structure of
the wire, and the more difficult it is for the free electrons
to find a path through the material.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
RESISTANCE
• The first three elements are related by the
following basic equation for resistance:
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
RESISTANCE
FIG. 3.2 Factors affecting the resistance of a
conductor.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
TEMPERATURE EFFECTS
FIG. 3.10 Demonstrating the effect of a positive and a negative temperature
coefficient on the resistance of a conductor.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
TYPES OF RESISTORS
Fixed Resistors
• Resistors are made in many forms,
but all belong in either of two groups:
fixed or variable.
• The most common of the low-
wattage, fixedtype resistors is the film
resistor.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
TYPES OF RESISTORS
Fixed Resistors
FIG. 3.12 Film resistors: (a) construction; (b) types.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
TYPES OF RESISTORS
Fixed Resistors
FIG. 3.13 Fixed-composition
resistors: (a) construction; (b)
appearance.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
TYPES OF RESISTORS
Fixed Resistors
FIG. 3.14 Fixed metal-oxide
resistors of different wattage
ratings.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
TYPES OF RESISTORS
Fixed Resistors
FIG. 3.15 Various types of fixed
resistors.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
TYPES OF RESISTORS
Variable Resistors
• Variable resistors, as the name implies,
have a terminal resistance that can be
varied by turning a dial, knob, screw, or
whatever seems appropriate for the
application.
• They can have two or three terminals, but
most have three terminals. If the two- or
three-terminal device is used as a variable
resistor, it is usually referred to as a
rheostat.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
TYPES OF RESISTORS
Variable Resistors
• If the three-terminal device is used for
controlling potential levels, it is then
commonly called a potentiometer.
• Even though a three-terminal device can
be used as a rheostat or a potentiometer
(depending on how it is connected), it is
typically called a potentiometer when listed
in trade magazines or requested for a
particular application.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
TYPES OF RESISTORS
Variable Resistors
FIG. 3.16 Potentiometer: (a) symbol; (b) and (c) rheostat connections; (d) rheostat
symbol.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
TYPES OF RESISTORS
Variable Resistors
FIG. 3.17 Molded composition-type
potentiometer. (Courtesy of Allen-
Bradley Co.)
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
TYPES OF RESISTORS
Variable Resistors
FIG. 3.18 Resistance components of a potentiometer: (a) between
outside terminals; (b) between wiper arm and each outside terminal.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
TYPES OF RESISTORS
Variable Resistors
FIG. 3.19 Variable resistors: (a) 4 mm ( 5/32 in.) trimmer (courtesy of Bourns, Inc.); (b)
conductive plastic and cermet elements (courtesy of Honeywell Clarostat); (c) three-point
wire-wound resistor.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
TYPES OF RESISTORS
Variable Resistors
FIG. 3.20 Potentiometer control
of voltage levels.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
COLOR CODING AND STANDARD
RESISTOR VALUES
• A wide variety of resistors, fixed or
variable, are large enough to have their
resistance in ohms printed on the casing.
• Some, however, are too small to have
numbers printed on them, so a system of
color coding is used.
• For the thin-film resistor, four, five, or six
bands may be used.
• The four-band scheme is described.
• Later in this section the purpose of the fifth
and sixth bands will be described.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
COLOR CODING AND STANDARD
RESISTOR VALUES
FIG. 3.21 Color coding for
fixed resistors.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
COLOR CODING AND STANDARD
RESISTOR VALUES
FIG. 3.22 Color coding.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
COLOR CODING AND STANDARD
RESISTOR VALUES
FIG. 3.23 Example 3.11.
FIG. 3.24 Example 3.12.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
COLOR CODING AND STANDARD
RESISTOR VALUES
FIG. 3.25 Five-band color coding
for fixed resistors.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
COLOR CODING AND STANDARD
RESISTOR VALUES
TABLE 3.5 Standard values of
commercially available resistors.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
COLOR CODING AND STANDARD
RESISTOR VALUES
FIG. 3.26 Guaranteeing the full range of resistor values for the given tolerance: (a) 20%;
(b) 10%.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
COLOR CODING AND STANDARD RESISTOR VALUES
Surface Mount Resistors
• In general, surface mount resistors are
marked in three ways: color coding, three
symbols, and two symbols.
– The color coding is the same as just
described earlier in this section for through-hole
resistors.
– The three-symbol approach uses three digits.
The first two define the first two digits of the
value; the last digit defines the power of the
power-of-ten multiplier.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
COLOR CODING AND STANDARD RESISTOR VALUES
Surface Mount Resistors
• The two-symbol marking uses a letter followed by
a number.
• The letter defines the value as in the following list.
• Note that all the numbers of the commercially
available list of Table 3.5 are included.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
CONDUCTANCE
• By finding the reciprocal of the resistance
of a material, we have a measure of how
well the material conducts electricity.
• The quantity is called conductance, has
the symbol G, and is measured in
siemens.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
OHMMETERS
FIG. 3.29 Checking the
FIG. 3.28 Measuring the continuity of a
resistance of a single connection.
element.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
RESISTANCE: METRIC UNITS
FIGURE 3.31 Defining r in ohm-centimeters.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
RESISTANCE: METRIC UNITS
TABLE 3.6 Resistivity (r) of various materials.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
RESISTANCE: METRIC UNITS
FIG. 3.32 Thin-film resistor. Example 3.16.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
RESISTANCE: METRIC UNITS
TABLE 3.7 Comparing levels of r in -cm.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
APPLICATIONS
Electric Baseboard Heating Element
• One of the most common applications
of resistance is in household fixtures
such as toasters and baseboard
heating where the heat generated by
current passing through a resistive
element is employed to perform a
useful function.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
APPLICATIONS
Electric Baseboard Heating Element
FIG. 3.41 Electric baseboard:
(a) 2-ft section; (b) interior; (c)
heating element; (d) nichrome
coil.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
APPLICATIONS
Dimmer Control in an Automobile
• A two-point rheostat is the primary
element in the control of the light
intensity on the dashboard and
accessories of a car.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
APPLICATIONS
Dimmer Control in an Automobile
FIG. 3.42 Dashboard dimmer control in an automobile.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
APPLICATIONS
Strain Gauges
• Any change in the shape of a structure can
be detected using strain gauges whose
resistance changes with applied stress or
flex.
FIG. 3.43 Resistive strain
gauge.
Introductory Circuit Analysis, 12/e Copyright ©2011 by Pearson Education, Inc.
Boylestad publishing as Pearson [imprint]
