Scribd
Upload
628 views3 pages

Chemical Composition of Steel Pipes

The document provides a specification chart for tubes and pipes listing various standards (e.g. ASTM, BS, DIN, JIS) that specify requirements for chemical composition and mechanical properties. For each standard, the chart lists requirements for elements like carbon, manganese, phosphorus and sulfur content, as well as minimum yield stress, tensile strength, and elongation. The standards cover specifications for carbon steel and alloy steel tubes for uses like heat exchangers, boilers, and high temperature or pressure services.

Uploaded by

emmas18
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
628 views3 pages

Chemical Composition of Steel Pipes

The document provides a specification chart for tubes and pipes listing various standards (e.g. ASTM, BS, DIN, JIS) that specify requirements for chemical composition and mechanical properties. For each standard, the chart lists requirements for elements like carbon, manganese, phosphorus and sulfur content, as well as minimum yield stress, tensile strength, and elongation. The standards cover specifications for carbon steel and alloy steel tubes for uses like heat exchangers, boilers, and high temperature or pressure services.

Uploaded by

emmas18
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
  • Specification Chart of Tubes and Pipes

SPECIFICATION CHART OF TUBES AND PIPES

CHEMICAL COMPOSITION MECHANICAL PROPERTIES

CS :- Carbon Steel AS :- Alloy Steel YIELD TENSILE ELONGATION IMPACT


STRESS STRENGTH IN TEST

SPECIFICATION TYPE C% Mn% P% S% Si % Cr % Cu % Mo % Ni % Va& MPa MPa 50mmMIN -50°1


MAX MAX MAX MAX MAX Longitudinal 40x10
STANDARD SPECIFICATION OF CARBON STEEL SEAMLESS TUBES / PIPES FOR HEAT EXCHANGER AND CONDENSER

ASTM A179 CS 0.06-0.18 0.27-0.63 0.035 0.035 - - - - - - 180MIN 325MIN 35.0 -


STANDARD SPECIFICATION OF CARBON STEEL SEAMLESS BOILER TUBES/PIPES FOR HIGH PRESSURE SERVICES

ASTM A192 CS 0.06-0.18 0.27-0.63 0.035 0.035 0.25MAX - - - - - 180MIN 325MIN 35.0 -
STANDARD SPECIFICATION OF CARBON STEEL SEAMLESS TUBES/PIPES FOR HIGH TEMPERATURE SERVICES

1 ASTM A53/A 0.25MAX 0.95MAX 0.050 0.060 - - - - - - 205MIN 330MIN 36.0 -


CS
2 ASTM A53/B 0.30MAX 1.20MAX 0.050 0.060 - - - - - - 240MIN 415MIN 29.5 -

3 ASTM A106/A 0.25MAX 0.27-0.93 0.035 0.035 0.10MIN 0.40MAX 0.40 0.15MAX 0.40 0.080 205MIN 330MIN 35.0 -

4 ASTM A106/B CS 0.30MAX 0.29-1.06 0.035 0.035 0.10MIN 0.40MAX 0.40 0.15MAX 0.40 0.080 240MIN 415MIN 30.0 -

5 ASTM A106/C 0.35MAX 0.29-1.06 0.035 0.035 0.10MIN 0.40MAX 0.40 0.15MAX 0.40 0.080 275MIN 485MIN 30.0 -
STANDARD SPECIFICATION OF SEAMLESS CARBON-MOLYBDENUM ALLOY-STEEL BOILER AND SUPER HEATER TUBES

8 ASTM A209/T1 0.10-0.20 0.30-0.80 0.025 0.025 0.10-0.50 - - 0.44-0.65 - - 205MIN 380MIN 30.0 -

9 ASTM A209/T1A AS 0.15-0.25 0.30-0.80 0.025 0.025 0.10-0.50 - - 0.44-0.65 - - 195MIN 365MIN 30.0 -

10 ASTM A209/Tb 0.14MAX 0.30-0.80 0.025 0.025 0.10-0.50 - - 0.44-0.65 - - 220MIN 415MIN 30.0 -
STANDARD SPECIFICATION OF CARBON STEEL BOILER AND SUPER HEATER TUBES

11 ASTM A210/A1 0.27MAX 0.93MAX 0.035 0.035 0.10MIN - - - - - 255MIN 415MIN 30.0 -
CS
12 ASTM A210/C 0.35MAX 0.29-1.06 0.035 0.035 0.10MIN - - - - - 275MIN 485MIN 30.0 -
STANDARD SPECIFICATION OF CARBON STEEL BOILER AND SUPER HEATER TUBES

13 ASTM A213/T2 0.10-0.20 0.30-0.60 0.025 0.025 0.10-0.30 0.50-0.81 - 0.44-0.65 - - 205MIN 415MIN 30.0 -

14 ASTM A213/T5 0.15MAX 0.30-0.60 0.025 0.025 0.50MAX 4.00-6.00 - 0.45-0.65 - - 205MIN 415MIN 30.0 -

15 ASTM A213/T11 AS 0.05-0.15 0.30-0.60 0.025 0.025 0.50-1.00 1.00-1.50 - 0.44-0.65 - - 205MIN 415MIN 30.0 -

16 ASTM A213/T12 0.05-0.15 0.30-0.61 0.025 0.025 0.50MAX 0.80-1.25 - 0.44-0.65 - - 205MIN 415MIN 30.0 -

17 ASTM A213/T22 0.05-0.15 0.30-0.60 0.025 0.025 0.50MAX 1.90-2.60 - 0.87-1.13 - - 205MIN 415MIN 30.0 -

Page 1
SPECIFICATION CHART OF TUBES AND PIPES
CHEMICAL COMPOSITION MECHANICAL PROPERTIES

CS :- Carbon Steel AS :- Alloy Steel YIELD TENSILE ELONGATION IMPACT


STRESS STRENGTH IN TEST

SPECIFICATION TYPE C% Mn% P% S% Si % Cr % Cu % Mo % Ni % Va& MPa MPa 50mmMIN -50°1


MAX MAX MAX MAX MAX Longitudinal 40x10

23 ASTM A335/P2 0.10-0.20 0.30-0.61 0.025 0.025 0.10-0.30 0.50-0.81 - 0.44-0.65 - - 205MIN 380MIN 30.0 -

24 ASTM A335/P5 0.15MAX 0.30-0.60 0.025 0.025 0.50MAX 4.00-6.00 - 0.45-0.65 - - 205MIN 415MIN 30.0 -

25 ASTM A335/P11 0.05-0.15 0.30-0.60 0.025 0.025 0.50-1.00 1.00-1.50 - 0.44-0.65 - - 205MIN 415MIN 30.0 -

26 ASTM A335/P12 0.05-0.15 0.30-0.60 0.025 0.025 0.50MAX 0.80-1.25 - 0.44-0.65 - - 220MIN 415MIN 30.0 -

27 ASTM A335/P22 0.05-0.15 0.30-0.60 0.025 0.025 0.50MAX 1.90-2.60 - 0.87-1.13 - - 205MIN 415MIN 30.0 -
STANDARD SPECIFICATION OF CARBON STEEL BOILER AND SUPER HEATER

28 BS/3059 /1/ 320 CS 0.16MAX 0.30-0.70 0.050 0.050 - - -         - - - 195MIN 320-480 25.0 -

29 BS/3059 /2/ 360 CS 0.17MAX 0.40-0.80 0.045 0.045 0.35MAX - -         - - - 215MIN 360-500 24.0 -

30 BS/3059 / 440 CS 0.12-0.18 0.90-1.20 0.040 0.035 0.10-0.35 - -         - - - 245MIN 440-560 21.0 -

32 BS/3059/2/ 620 AS 0.12-0.15 0.40-0.70 0.040 0.040 0.10-0.35 0.70-1.10 - 0.45-0.65 - - 180 MIN 460-640 22.0 -

31 BS/3059/2/ 622 AS 0.08-0.15 0.40-0.70 0.040 0.040 0.10-0.35 2.00-2.50 0.90-1.20 275MIN 490-640 20.0

STANDARD SPECIFICATION FOR SEAMLESS ALLOY STEEL TUBES FOR BOILER, PIPELINES, PRESSURE VESSEL FOR TEMPRATURE UP TO 6000C

33 DIN/17175 ST35.8 CS 0.17MAX 0.40-0.80 0.040 0.040 0.10-0.35 - -         - - - 235MIN 340-441 25.0 -

34 DIN/17175 ST45.8 CS 0.21 MAX 0.40-1.20 0.040 0.040 0.10-0.35 - -         - - - 235MIN 441-540 25.0 -

35 DIN/17175 15M03 AS 0.12-0.20 0.40-0.80 0.035 0.035 0.10-0.35 - - 0.25-0.35 - - 285MIN 441-540 21.0 -

36 DIN/17175 13CM044 AS 0.10-0.18 0.40-0.70 0.035 0.035 0.10-0.35 0.70-1.00 - 0.45-0.65 - - 294MIN 441-570 22.0 -

DIN/17175
36 AS 0.15MAX 0.40-0.80 0.035 0.035 0.10-0.35 2.00-2.50 - 0.90-1.10 - - 265MIN 441-590 20.0 -
10CrMo910
STANDARD SPECIFICATION FOR SEAMLESS CARBON STEEL TUBES

37 JIS3445 STKM 11A 0.12MAX 0.60MAX 0.040 0.040 0.35MAX - - - - - - 294MIN 35.0 -

38 JIS3445 STKM 12A 0.20MAX 0.60MAX 0.040 0.040 0.35MAX - - - - - 177MIN 344MIN 35.0 -

Page 2
SPECIFICATION CHART OF TUBES AND PIPES
CHEMICAL COMPOSITION MECHANICAL PROPERTIES

CS :- Carbon Steel AS :- Alloy Steel YIELD TENSILE ELONGATION IMPACT


STRESS STRENGTH IN TEST

SPECIFICATION TYPE C% Mn% P% S% Si % Cr % Cu % Mo % Ni % Va& MPa MPa 50mmMIN -50°1


MAX MAX MAX MAX MAX Longitudinal 40x10
39 JIS3445 STKM 12B 0.20MAX 0.60MAX 0.040 0.040 0.35MAX - - - - - 274MIN 393MIN 25.0 -

40 JIS3445 STKM 12C CS 0.20MAX 0.60MAX 0.040 0.040 0.35MAX - - - - - 353MIN 470MIN 20.0 -

41 JIS3445 STKM 13C 0.25MAX 0.30MAX 0.040 0.040 0.35MAX - - - - - 216MIN 373MIN 30.0 -

42 JIS3445 STKM 13B 0.25MAX 0.30-0.90 0.040 0.040 0.35MAX - - - - - 304MIN 442MIN 20.0 -

JIS 3461
43 0.32MAX 0.30-0.80 0.035 0.035 0.35MAX - - - - - 255MIN 412MIN 30.0 -
STB42
JIS 3461
44 0.18MAX 0.30-0.60 0.035 0.035 0.35MAX - - - - - 177MIN 344MIN 30.0 -
STB35

45 ASTM A 519 SAE 1010 0.08-0.13 0.30-0.60 0.040 0.050 - - - - - - -

46 ASTM A 519 SAE 1015 CS 0.13-0.18 0.30-0.60 0.040 0.050 - - - - - - -

47 ASTM A 519 SAE 1020 0.18-0.23 0.30-0.60 0.040 0.050 - - - - - - -

48 ASTM A 519 SAE 1025 0.22-0.28 0.30-0.60 0.040 0.050 - - - - - - -

49 ASTM A 519 SAE 1030 CS 0.28-0.34 0.60-0.90 0.040 0.050 - - - - - - -

50 ASTM A 519 SAE 1035 0.32-0.38 0.60-0.90 0.040 0.050 - - - - - - -

51 ASTM A 519 SAE 1040 0.37-0.44 0.60-0.90 0.040 0.050 - - - - - - -

52 ASTM A 519 SAE 1045 0.43-0.50 0.60-0.90 0.040 0.050 - - - - - - -

53 ASTM A 519 SAE 1050 0.48-0.55 0.60-0.90 0.040 0.050 - - - - - - -

Page 3

You might also like